summaryrefslogtreecommitdiffstats
path: root/drivers/hwmon/abituguru3.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/hwmon/abituguru3.c')
-rw-r--r--drivers/hwmon/abituguru3.c1303
1 files changed, 1303 insertions, 0 deletions
diff --git a/drivers/hwmon/abituguru3.c b/drivers/hwmon/abituguru3.c
new file mode 100644
index 0000000000..afb21f7303
--- /dev/null
+++ b/drivers/hwmon/abituguru3.c
@@ -0,0 +1,1303 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * abituguru3.c
+ *
+ * Copyright (c) 2006-2008 Hans de Goede <hdegoede@redhat.com>
+ * Copyright (c) 2008 Alistair John Strachan <alistair@devzero.co.uk>
+ */
+/*
+ * This driver supports the sensor part of revision 3 of the custom Abit uGuru
+ * chip found on newer Abit uGuru motherboards. Note: because of lack of specs
+ * only reading the sensors and their settings is supported.
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/jiffies.h>
+#include <linux/mutex.h>
+#include <linux/err.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/dmi.h>
+#include <linux/io.h>
+
+/* uGuru3 bank addresses */
+#define ABIT_UGURU3_SETTINGS_BANK 0x01
+#define ABIT_UGURU3_SENSORS_BANK 0x08
+#define ABIT_UGURU3_MISC_BANK 0x09
+#define ABIT_UGURU3_ALARMS_START 0x1E
+#define ABIT_UGURU3_SETTINGS_START 0x24
+#define ABIT_UGURU3_VALUES_START 0x80
+#define ABIT_UGURU3_BOARD_ID 0x0A
+/* uGuru3 sensor bank flags */ /* Alarm if: */
+#define ABIT_UGURU3_TEMP_HIGH_ALARM_ENABLE 0x01 /* temp over warn */
+#define ABIT_UGURU3_VOLT_HIGH_ALARM_ENABLE 0x02 /* volt over max */
+#define ABIT_UGURU3_VOLT_LOW_ALARM_ENABLE 0x04 /* volt under min */
+#define ABIT_UGURU3_TEMP_HIGH_ALARM_FLAG 0x10 /* temp is over warn */
+#define ABIT_UGURU3_VOLT_HIGH_ALARM_FLAG 0x20 /* volt is over max */
+#define ABIT_UGURU3_VOLT_LOW_ALARM_FLAG 0x40 /* volt is under min */
+#define ABIT_UGURU3_FAN_LOW_ALARM_ENABLE 0x01 /* fan under min */
+#define ABIT_UGURU3_BEEP_ENABLE 0x08 /* beep if alarm */
+#define ABIT_UGURU3_SHUTDOWN_ENABLE 0x80 /* shutdown if alarm */
+/* sensor types */
+#define ABIT_UGURU3_IN_SENSOR 0
+#define ABIT_UGURU3_TEMP_SENSOR 1
+#define ABIT_UGURU3_FAN_SENSOR 2
+
+/*
+ * Timeouts / Retries, if these turn out to need a lot of fiddling we could
+ * convert them to params. Determined by trial and error. I assume this is
+ * cpu-speed independent, since the ISA-bus and not the CPU should be the
+ * bottleneck.
+ */
+#define ABIT_UGURU3_WAIT_TIMEOUT 250
+/*
+ * Normally the 0xAC at the end of synchronize() is reported after the
+ * first read, but sometimes not and we need to poll
+ */
+#define ABIT_UGURU3_SYNCHRONIZE_TIMEOUT 5
+/* utility macros */
+#define ABIT_UGURU3_NAME "abituguru3"
+#define ABIT_UGURU3_DEBUG(format, arg...) \
+ do { \
+ if (verbose) \
+ pr_debug(format , ## arg); \
+ } while (0)
+
+/* Macros to help calculate the sysfs_names array length */
+#define ABIT_UGURU3_MAX_NO_SENSORS 26
+/*
+ * sum of strlen +1 of: in??_input\0, in??_{min,max}\0, in??_{min,max}_alarm\0,
+ * in??_{min,max}_alarm_enable\0, in??_beep\0, in??_shutdown\0, in??_label\0
+ */
+#define ABIT_UGURU3_IN_NAMES_LENGTH \
+ (11 + 2 * 9 + 2 * 15 + 2 * 22 + 10 + 14 + 11)
+/*
+ * sum of strlen +1 of: temp??_input\0, temp??_max\0, temp??_crit\0,
+ * temp??_alarm\0, temp??_alarm_enable\0, temp??_beep\0, temp??_shutdown\0,
+ * temp??_label\0
+ */
+#define ABIT_UGURU3_TEMP_NAMES_LENGTH (13 + 11 + 12 + 13 + 20 + 12 + 16 + 13)
+/*
+ * sum of strlen +1 of: fan??_input\0, fan??_min\0, fan??_alarm\0,
+ * fan??_alarm_enable\0, fan??_beep\0, fan??_shutdown\0, fan??_label\0
+ */
+#define ABIT_UGURU3_FAN_NAMES_LENGTH (12 + 10 + 12 + 19 + 11 + 15 + 12)
+/*
+ * Worst case scenario 16 in sensors (longest names_length) and the rest
+ * temp sensors (second longest names_length).
+ */
+#define ABIT_UGURU3_SYSFS_NAMES_LENGTH (16 * ABIT_UGURU3_IN_NAMES_LENGTH + \
+ (ABIT_UGURU3_MAX_NO_SENSORS - 16) * ABIT_UGURU3_TEMP_NAMES_LENGTH)
+
+/*
+ * All the macros below are named identical to the openguru2 program
+ * reverse engineered by Louis Kruger, hence the names might not be 100%
+ * logical. I could come up with better names, but I prefer keeping the names
+ * identical so that this driver can be compared with his work more easily.
+ */
+/* Two i/o-ports are used by uGuru */
+#define ABIT_UGURU3_BASE 0x00E0
+#define ABIT_UGURU3_CMD 0x00
+#define ABIT_UGURU3_DATA 0x04
+#define ABIT_UGURU3_REGION_LENGTH 5
+/*
+ * The wait_xxx functions return this on success and the last contents
+ * of the DATA register (0-255) on failure.
+ */
+#define ABIT_UGURU3_SUCCESS -1
+/* uGuru status flags */
+#define ABIT_UGURU3_STATUS_READY_FOR_READ 0x01
+#define ABIT_UGURU3_STATUS_BUSY 0x02
+
+
+/* Structures */
+struct abituguru3_sensor_info {
+ const char *name;
+ int port;
+ int type;
+ int multiplier;
+ int divisor;
+ int offset;
+};
+
+/* Avoid use of flexible array members */
+#define ABIT_UGURU3_MAX_DMI_NAMES 2
+
+struct abituguru3_motherboard_info {
+ u16 id;
+ const char *dmi_name[ABIT_UGURU3_MAX_DMI_NAMES + 1];
+ /* + 1 -> end of sensors indicated by a sensor with name == NULL */
+ struct abituguru3_sensor_info sensors[ABIT_UGURU3_MAX_NO_SENSORS + 1];
+};
+
+/*
+ * For the Abit uGuru, we need to keep some data in memory.
+ * The structure is dynamically allocated, at the same time when a new
+ * abituguru3 device is allocated.
+ */
+struct abituguru3_data {
+ struct device *hwmon_dev; /* hwmon registered device */
+ struct mutex update_lock; /* protect access to data and uGuru */
+ unsigned short addr; /* uguru base address */
+ bool valid; /* true if following fields are valid */
+ unsigned long last_updated; /* In jiffies */
+
+ /*
+ * For convenience the sysfs attr and their names are generated
+ * automatically. We have max 10 entries per sensor (for in sensors)
+ */
+ struct sensor_device_attribute_2 sysfs_attr[ABIT_UGURU3_MAX_NO_SENSORS
+ * 10];
+
+ /* Buffer to store the dynamically generated sysfs names */
+ char sysfs_names[ABIT_UGURU3_SYSFS_NAMES_LENGTH];
+
+ /* Pointer to the sensors info for the detected motherboard */
+ const struct abituguru3_sensor_info *sensors;
+
+ /*
+ * The abituguru3 supports up to 48 sensors, and thus has registers
+ * sets for 48 sensors, for convenience reasons / simplicity of the
+ * code we always read and store all registers for all 48 sensors
+ */
+
+ /* Alarms for all 48 sensors (1 bit per sensor) */
+ u8 alarms[48/8];
+
+ /* Value of all 48 sensors */
+ u8 value[48];
+
+ /*
+ * Settings of all 48 sensors, note in and temp sensors (the first 32
+ * sensors) have 3 bytes of settings, while fans only have 2 bytes,
+ * for convenience we use 3 bytes for all sensors
+ */
+ u8 settings[48][3];
+};
+
+
+/* Constants */
+static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
+ { 0x000C, { NULL } /* Unknown, need DMI string */, {
+ { "CPU Core", 0, 0, 10, 1, 0 },
+ { "DDR", 1, 0, 10, 1, 0 },
+ { "DDR VTT", 2, 0, 10, 1, 0 },
+ { "CPU VTT 1.2V", 3, 0, 10, 1, 0 },
+ { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 },
+ { "MCH 2.5V", 5, 0, 20, 1, 0 },
+ { "ICH 1.05V", 6, 0, 10, 1, 0 },
+ { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 },
+ { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 },
+ { "ATX +5V", 9, 0, 30, 1, 0 },
+ { "+3.3V", 10, 0, 20, 1, 0 },
+ { "5VSB", 11, 0, 30, 1, 0 },
+ { "CPU", 24, 1, 1, 1, 0 },
+ { "System", 25, 1, 1, 1, 0 },
+ { "PWM", 26, 1, 1, 1, 0 },
+ { "CPU Fan", 32, 2, 60, 1, 0 },
+ { "NB Fan", 33, 2, 60, 1, 0 },
+ { "SYS FAN", 34, 2, 60, 1, 0 },
+ { "AUX1 Fan", 35, 2, 60, 1, 0 },
+ { NULL, 0, 0, 0, 0, 0 } }
+ },
+ { 0x000D, { NULL } /* Abit AW8, need DMI string */, {
+ { "CPU Core", 0, 0, 10, 1, 0 },
+ { "DDR", 1, 0, 10, 1, 0 },
+ { "DDR VTT", 2, 0, 10, 1, 0 },
+ { "CPU VTT 1.2V", 3, 0, 10, 1, 0 },
+ { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 },
+ { "MCH 2.5V", 5, 0, 20, 1, 0 },
+ { "ICH 1.05V", 6, 0, 10, 1, 0 },
+ { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 },
+ { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 },
+ { "ATX +5V", 9, 0, 30, 1, 0 },
+ { "+3.3V", 10, 0, 20, 1, 0 },
+ { "5VSB", 11, 0, 30, 1, 0 },
+ { "CPU", 24, 1, 1, 1, 0 },
+ { "System", 25, 1, 1, 1, 0 },
+ { "PWM1", 26, 1, 1, 1, 0 },
+ { "PWM2", 27, 1, 1, 1, 0 },
+ { "PWM3", 28, 1, 1, 1, 0 },
+ { "PWM4", 29, 1, 1, 1, 0 },
+ { "CPU Fan", 32, 2, 60, 1, 0 },
+ { "NB Fan", 33, 2, 60, 1, 0 },
+ { "SYS Fan", 34, 2, 60, 1, 0 },
+ { "AUX1 Fan", 35, 2, 60, 1, 0 },
+ { "AUX2 Fan", 36, 2, 60, 1, 0 },
+ { "AUX3 Fan", 37, 2, 60, 1, 0 },
+ { "AUX4 Fan", 38, 2, 60, 1, 0 },
+ { "AUX5 Fan", 39, 2, 60, 1, 0 },
+ { NULL, 0, 0, 0, 0, 0 } }
+ },
+ { 0x000E, { NULL } /* AL-8, need DMI string */, {
+ { "CPU Core", 0, 0, 10, 1, 0 },
+ { "DDR", 1, 0, 10, 1, 0 },
+ { "DDR VTT", 2, 0, 10, 1, 0 },
+ { "CPU VTT 1.2V", 3, 0, 10, 1, 0 },
+ { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 },
+ { "MCH 2.5V", 5, 0, 20, 1, 0 },
+ { "ICH 1.05V", 6, 0, 10, 1, 0 },
+ { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 },
+ { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 },
+ { "ATX +5V", 9, 0, 30, 1, 0 },
+ { "+3.3V", 10, 0, 20, 1, 0 },
+ { "5VSB", 11, 0, 30, 1, 0 },
+ { "CPU", 24, 1, 1, 1, 0 },
+ { "System", 25, 1, 1, 1, 0 },
+ { "PWM", 26, 1, 1, 1, 0 },
+ { "CPU Fan", 32, 2, 60, 1, 0 },
+ { "NB Fan", 33, 2, 60, 1, 0 },
+ { "SYS Fan", 34, 2, 60, 1, 0 },
+ { NULL, 0, 0, 0, 0, 0 } }
+ },
+ { 0x000F, { NULL } /* Unknown, need DMI string */, {
+
+ { "CPU Core", 0, 0, 10, 1, 0 },
+ { "DDR", 1, 0, 10, 1, 0 },
+ { "DDR VTT", 2, 0, 10, 1, 0 },
+ { "CPU VTT 1.2V", 3, 0, 10, 1, 0 },
+ { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 },
+ { "MCH 2.5V", 5, 0, 20, 1, 0 },
+ { "ICH 1.05V", 6, 0, 10, 1, 0 },
+ { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 },
+ { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 },
+ { "ATX +5V", 9, 0, 30, 1, 0 },
+ { "+3.3V", 10, 0, 20, 1, 0 },
+ { "5VSB", 11, 0, 30, 1, 0 },
+ { "CPU", 24, 1, 1, 1, 0 },
+ { "System", 25, 1, 1, 1, 0 },
+ { "PWM", 26, 1, 1, 1, 0 },
+ { "CPU Fan", 32, 2, 60, 1, 0 },
+ { "NB Fan", 33, 2, 60, 1, 0 },
+ { "SYS Fan", 34, 2, 60, 1, 0 },
+ { NULL, 0, 0, 0, 0, 0 } }
+ },
+ { 0x0010, { NULL } /* Abit NI8 SLI GR, need DMI string */, {
+ { "CPU Core", 0, 0, 10, 1, 0 },
+ { "DDR", 1, 0, 10, 1, 0 },
+ { "DDR VTT", 2, 0, 10, 1, 0 },
+ { "CPU VTT 1.2V", 3, 0, 10, 1, 0 },
+ { "NB 1.4V", 4, 0, 10, 1, 0 },
+ { "SB 1.5V", 6, 0, 10, 1, 0 },
+ { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 },
+ { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 },
+ { "ATX +5V", 9, 0, 30, 1, 0 },
+ { "+3.3V", 10, 0, 20, 1, 0 },
+ { "5VSB", 11, 0, 30, 1, 0 },
+ { "CPU", 24, 1, 1, 1, 0 },
+ { "SYS", 25, 1, 1, 1, 0 },
+ { "PWM", 26, 1, 1, 1, 0 },
+ { "CPU Fan", 32, 2, 60, 1, 0 },
+ { "NB Fan", 33, 2, 60, 1, 0 },
+ { "SYS Fan", 34, 2, 60, 1, 0 },
+ { "AUX1 Fan", 35, 2, 60, 1, 0 },
+ { "OTES1 Fan", 36, 2, 60, 1, 0 },
+ { NULL, 0, 0, 0, 0, 0 } }
+ },
+ { 0x0011, { "AT8 32X", NULL }, {
+ { "CPU Core", 0, 0, 10, 1, 0 },
+ { "DDR", 1, 0, 20, 1, 0 },
+ { "DDR VTT", 2, 0, 10, 1, 0 },
+ { "CPU VDDA 2.5V", 6, 0, 20, 1, 0 },
+ { "NB 1.8V", 4, 0, 10, 1, 0 },
+ { "NB 1.8V Dual", 5, 0, 10, 1, 0 },
+ { "HTV 1.2", 3, 0, 10, 1, 0 },
+ { "PCIE 1.2V", 12, 0, 10, 1, 0 },
+ { "NB 1.2V", 13, 0, 10, 1, 0 },
+ { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 },
+ { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 },
+ { "ATX +5V", 9, 0, 30, 1, 0 },
+ { "+3.3V", 10, 0, 20, 1, 0 },
+ { "5VSB", 11, 0, 30, 1, 0 },
+ { "CPU", 24, 1, 1, 1, 0 },
+ { "NB", 25, 1, 1, 1, 0 },
+ { "System", 26, 1, 1, 1, 0 },
+ { "PWM", 27, 1, 1, 1, 0 },
+ { "CPU Fan", 32, 2, 60, 1, 0 },
+ { "NB Fan", 33, 2, 60, 1, 0 },
+ { "SYS Fan", 34, 2, 60, 1, 0 },
+ { "AUX1 Fan", 35, 2, 60, 1, 0 },
+ { "AUX2 Fan", 36, 2, 60, 1, 0 },
+ { "AUX3 Fan", 37, 2, 60, 1, 0 },
+ { NULL, 0, 0, 0, 0, 0 } }
+ },
+ { 0x0012, { NULL } /* Abit AN8 32X, need DMI string */, {
+ { "CPU Core", 0, 0, 10, 1, 0 },
+ { "DDR", 1, 0, 20, 1, 0 },
+ { "DDR VTT", 2, 0, 10, 1, 0 },
+ { "HyperTransport", 3, 0, 10, 1, 0 },
+ { "CPU VDDA 2.5V", 5, 0, 20, 1, 0 },
+ { "NB", 4, 0, 10, 1, 0 },
+ { "SB", 6, 0, 10, 1, 0 },
+ { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 },
+ { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 },
+ { "ATX +5V", 9, 0, 30, 1, 0 },
+ { "+3.3V", 10, 0, 20, 1, 0 },
+ { "5VSB", 11, 0, 30, 1, 0 },
+ { "CPU", 24, 1, 1, 1, 0 },
+ { "SYS", 25, 1, 1, 1, 0 },
+ { "PWM", 26, 1, 1, 1, 0 },
+ { "CPU Fan", 32, 2, 60, 1, 0 },
+ { "NB Fan", 33, 2, 60, 1, 0 },
+ { "SYS Fan", 34, 2, 60, 1, 0 },
+ { "AUX1 Fan", 36, 2, 60, 1, 0 },
+ { NULL, 0, 0, 0, 0, 0 } }
+ },
+ { 0x0013, { NULL } /* Abit AW8D, need DMI string */, {
+ { "CPU Core", 0, 0, 10, 1, 0 },
+ { "DDR", 1, 0, 10, 1, 0 },
+ { "DDR VTT", 2, 0, 10, 1, 0 },
+ { "CPU VTT 1.2V", 3, 0, 10, 1, 0 },
+ { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 },
+ { "MCH 2.5V", 5, 0, 20, 1, 0 },
+ { "ICH 1.05V", 6, 0, 10, 1, 0 },
+ { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 },
+ { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 },
+ { "ATX +5V", 9, 0, 30, 1, 0 },
+ { "+3.3V", 10, 0, 20, 1, 0 },
+ { "5VSB", 11, 0, 30, 1, 0 },
+ { "CPU", 24, 1, 1, 1, 0 },
+ { "System", 25, 1, 1, 1, 0 },
+ { "PWM1", 26, 1, 1, 1, 0 },
+ { "PWM2", 27, 1, 1, 1, 0 },
+ { "PWM3", 28, 1, 1, 1, 0 },
+ { "PWM4", 29, 1, 1, 1, 0 },
+ { "CPU Fan", 32, 2, 60, 1, 0 },
+ { "NB Fan", 33, 2, 60, 1, 0 },
+ { "SYS Fan", 34, 2, 60, 1, 0 },
+ { "AUX1 Fan", 35, 2, 60, 1, 0 },
+ { "AUX2 Fan", 36, 2, 60, 1, 0 },
+ { "AUX3 Fan", 37, 2, 60, 1, 0 },
+ { "AUX4 Fan", 38, 2, 60, 1, 0 },
+ { "AUX5 Fan", 39, 2, 60, 1, 0 },
+ { NULL, 0, 0, 0, 0, 0 } }
+ },
+ { 0x0014, { "AB9", "AB9 Pro", NULL }, {
+ { "CPU Core", 0, 0, 10, 1, 0 },
+ { "DDR", 1, 0, 10, 1, 0 },
+ { "DDR VTT", 2, 0, 10, 1, 0 },
+ { "CPU VTT 1.2V", 3, 0, 10, 1, 0 },
+ { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 },
+ { "MCH 2.5V", 5, 0, 20, 1, 0 },
+ { "ICH 1.05V", 6, 0, 10, 1, 0 },
+ { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 },
+ { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 },
+ { "ATX +5V", 9, 0, 30, 1, 0 },
+ { "+3.3V", 10, 0, 20, 1, 0 },
+ { "5VSB", 11, 0, 30, 1, 0 },
+ { "CPU", 24, 1, 1, 1, 0 },
+ { "System", 25, 1, 1, 1, 0 },
+ { "PWM", 26, 1, 1, 1, 0 },
+ { "CPU Fan", 32, 2, 60, 1, 0 },
+ { "NB Fan", 33, 2, 60, 1, 0 },
+ { "SYS Fan", 34, 2, 60, 1, 0 },
+ { NULL, 0, 0, 0, 0, 0 } }
+ },
+ { 0x0015, { NULL } /* Unknown, need DMI string */, {
+ { "CPU Core", 0, 0, 10, 1, 0 },
+ { "DDR", 1, 0, 20, 1, 0 },
+ { "DDR VTT", 2, 0, 10, 1, 0 },
+ { "HyperTransport", 3, 0, 10, 1, 0 },
+ { "CPU VDDA 2.5V", 5, 0, 20, 1, 0 },
+ { "NB", 4, 0, 10, 1, 0 },
+ { "SB", 6, 0, 10, 1, 0 },
+ { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 },
+ { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 },
+ { "ATX +5V", 9, 0, 30, 1, 0 },
+ { "+3.3V", 10, 0, 20, 1, 0 },
+ { "5VSB", 11, 0, 30, 1, 0 },
+ { "CPU", 24, 1, 1, 1, 0 },
+ { "SYS", 25, 1, 1, 1, 0 },
+ { "PWM", 26, 1, 1, 1, 0 },
+ { "CPU Fan", 32, 2, 60, 1, 0 },
+ { "NB Fan", 33, 2, 60, 1, 0 },
+ { "SYS Fan", 34, 2, 60, 1, 0 },
+ { "AUX1 Fan", 33, 2, 60, 1, 0 },
+ { "AUX2 Fan", 35, 2, 60, 1, 0 },
+ { "AUX3 Fan", 36, 2, 60, 1, 0 },
+ { NULL, 0, 0, 0, 0, 0 } }
+ },
+ { 0x0016, { "AW9D-MAX", NULL }, {
+ { "CPU Core", 0, 0, 10, 1, 0 },
+ { "DDR2", 1, 0, 20, 1, 0 },
+ { "DDR2 VTT", 2, 0, 10, 1, 0 },
+ { "CPU VTT 1.2V", 3, 0, 10, 1, 0 },
+ { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 },
+ { "MCH 2.5V", 5, 0, 20, 1, 0 },
+ { "ICH 1.05V", 6, 0, 10, 1, 0 },
+ { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 },
+ { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 },
+ { "ATX +5V", 9, 0, 30, 1, 0 },
+ { "+3.3V", 10, 0, 20, 1, 0 },
+ { "5VSB", 11, 0, 30, 1, 0 },
+ { "CPU", 24, 1, 1, 1, 0 },
+ { "System", 25, 1, 1, 1, 0 },
+ { "PWM1", 26, 1, 1, 1, 0 },
+ { "PWM2", 27, 1, 1, 1, 0 },
+ { "PWM3", 28, 1, 1, 1, 0 },
+ { "PWM4", 29, 1, 1, 1, 0 },
+ { "CPU Fan", 32, 2, 60, 1, 0 },
+ { "NB Fan", 33, 2, 60, 1, 0 },
+ { "SYS Fan", 34, 2, 60, 1, 0 },
+ { "AUX1 Fan", 35, 2, 60, 1, 0 },
+ { "AUX2 Fan", 36, 2, 60, 1, 0 },
+ { "AUX3 Fan", 37, 2, 60, 1, 0 },
+ { "OTES1 Fan", 38, 2, 60, 1, 0 },
+ { NULL, 0, 0, 0, 0, 0 } }
+ },
+ { 0x0017, { NULL } /* Unknown, need DMI string */, {
+ { "CPU Core", 0, 0, 10, 1, 0 },
+ { "DDR2", 1, 0, 20, 1, 0 },
+ { "DDR2 VTT", 2, 0, 10, 1, 0 },
+ { "HyperTransport", 3, 0, 10, 1, 0 },
+ { "CPU VDDA 2.5V", 6, 0, 20, 1, 0 },
+ { "NB 1.8V", 4, 0, 10, 1, 0 },
+ { "NB 1.2V ", 13, 0, 10, 1, 0 },
+ { "SB 1.2V", 5, 0, 10, 1, 0 },
+ { "PCIE 1.2V", 12, 0, 10, 1, 0 },
+ { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 },
+ { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 },
+ { "ATX +5V", 9, 0, 30, 1, 0 },
+ { "ATX +3.3V", 10, 0, 20, 1, 0 },
+ { "ATX 5VSB", 11, 0, 30, 1, 0 },
+ { "CPU", 24, 1, 1, 1, 0 },
+ { "System", 26, 1, 1, 1, 0 },
+ { "PWM", 27, 1, 1, 1, 0 },
+ { "CPU FAN", 32, 2, 60, 1, 0 },
+ { "SYS FAN", 34, 2, 60, 1, 0 },
+ { "AUX1 FAN", 35, 2, 60, 1, 0 },
+ { "AUX2 FAN", 36, 2, 60, 1, 0 },
+ { "AUX3 FAN", 37, 2, 60, 1, 0 },
+ { NULL, 0, 0, 0, 0, 0 } }
+ },
+ { 0x0018, { "AB9 QuadGT", NULL }, {
+ { "CPU Core", 0, 0, 10, 1, 0 },
+ { "DDR2", 1, 0, 20, 1, 0 },
+ { "DDR2 VTT", 2, 0, 10, 1, 0 },
+ { "CPU VTT", 3, 0, 10, 1, 0 },
+ { "MCH 1.25V", 4, 0, 10, 1, 0 },
+ { "ICHIO 1.5V", 5, 0, 10, 1, 0 },
+ { "ICH 1.05V", 6, 0, 10, 1, 0 },
+ { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 },
+ { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 },
+ { "ATX +5V", 9, 0, 30, 1, 0 },
+ { "+3.3V", 10, 0, 20, 1, 0 },
+ { "5VSB", 11, 0, 30, 1, 0 },
+ { "CPU", 24, 1, 1, 1, 0 },
+ { "System", 25, 1, 1, 1, 0 },
+ { "PWM Phase1", 26, 1, 1, 1, 0 },
+ { "PWM Phase2", 27, 1, 1, 1, 0 },
+ { "PWM Phase3", 28, 1, 1, 1, 0 },
+ { "PWM Phase4", 29, 1, 1, 1, 0 },
+ { "PWM Phase5", 30, 1, 1, 1, 0 },
+ { "CPU Fan", 32, 2, 60, 1, 0 },
+ { "SYS Fan", 34, 2, 60, 1, 0 },
+ { "AUX1 Fan", 33, 2, 60, 1, 0 },
+ { "AUX2 Fan", 35, 2, 60, 1, 0 },
+ { "AUX3 Fan", 36, 2, 60, 1, 0 },
+ { NULL, 0, 0, 0, 0, 0 } }
+ },
+ { 0x0019, { "IN9 32X MAX", NULL }, {
+ { "CPU Core", 7, 0, 10, 1, 0 },
+ { "DDR2", 13, 0, 20, 1, 0 },
+ { "DDR2 VTT", 14, 0, 10, 1, 0 },
+ { "CPU VTT", 3, 0, 20, 1, 0 },
+ { "NB 1.2V", 4, 0, 10, 1, 0 },
+ { "SB 1.5V", 6, 0, 10, 1, 0 },
+ { "HyperTransport", 5, 0, 10, 1, 0 },
+ { "ATX +12V (24-Pin)", 12, 0, 60, 1, 0 },
+ { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 },
+ { "ATX +5V", 9, 0, 30, 1, 0 },
+ { "ATX +3.3V", 10, 0, 20, 1, 0 },
+ { "ATX 5VSB", 11, 0, 30, 1, 0 },
+ { "CPU", 24, 1, 1, 1, 0 },
+ { "System", 25, 1, 1, 1, 0 },
+ { "PWM Phase1", 26, 1, 1, 1, 0 },
+ { "PWM Phase2", 27, 1, 1, 1, 0 },
+ { "PWM Phase3", 28, 1, 1, 1, 0 },
+ { "PWM Phase4", 29, 1, 1, 1, 0 },
+ { "PWM Phase5", 30, 1, 1, 1, 0 },
+ { "CPU FAN", 32, 2, 60, 1, 0 },
+ { "SYS FAN", 34, 2, 60, 1, 0 },
+ { "AUX1 FAN", 33, 2, 60, 1, 0 },
+ { "AUX2 FAN", 35, 2, 60, 1, 0 },
+ { "AUX3 FAN", 36, 2, 60, 1, 0 },
+ { NULL, 0, 0, 0, 0, 0 } }
+ },
+ { 0x001A, { "IP35 Pro", "IP35 Pro XE", NULL }, {
+ { "CPU Core", 0, 0, 10, 1, 0 },
+ { "DDR2", 1, 0, 20, 1, 0 },
+ { "DDR2 VTT", 2, 0, 10, 1, 0 },
+ { "CPU VTT 1.2V", 3, 0, 10, 1, 0 },
+ { "MCH 1.25V", 4, 0, 10, 1, 0 },
+ { "ICHIO 1.5V", 5, 0, 10, 1, 0 },
+ { "ICH 1.05V", 6, 0, 10, 1, 0 },
+ { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 },
+ { "ATX +12V (8-pin)", 8, 0, 60, 1, 0 },
+ { "ATX +5V", 9, 0, 30, 1, 0 },
+ { "+3.3V", 10, 0, 20, 1, 0 },
+ { "5VSB", 11, 0, 30, 1, 0 },
+ { "CPU", 24, 1, 1, 1, 0 },
+ { "System", 25, 1, 1, 1, 0 },
+ { "PWM", 26, 1, 1, 1, 0 },
+ { "PWM Phase2", 27, 1, 1, 1, 0 },
+ { "PWM Phase3", 28, 1, 1, 1, 0 },
+ { "PWM Phase4", 29, 1, 1, 1, 0 },
+ { "PWM Phase5", 30, 1, 1, 1, 0 },
+ { "CPU Fan", 32, 2, 60, 1, 0 },
+ { "SYS Fan", 34, 2, 60, 1, 0 },
+ { "AUX1 Fan", 33, 2, 60, 1, 0 },
+ { "AUX2 Fan", 35, 2, 60, 1, 0 },
+ { "AUX3 Fan", 36, 2, 60, 1, 0 },
+ { "AUX4 Fan", 37, 2, 60, 1, 0 },
+ { NULL, 0, 0, 0, 0, 0 } }
+ },
+ { 0x001B, { NULL } /* Unknown, need DMI string */, {
+ { "CPU Core", 0, 0, 10, 1, 0 },
+ { "DDR3", 1, 0, 20, 1, 0 },
+ { "DDR3 VTT", 2, 0, 10, 1, 0 },
+ { "CPU VTT", 3, 0, 10, 1, 0 },
+ { "MCH 1.25V", 4, 0, 10, 1, 0 },
+ { "ICHIO 1.5V", 5, 0, 10, 1, 0 },
+ { "ICH 1.05V", 6, 0, 10, 1, 0 },
+ { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 },
+ { "ATX +12V (8-pin)", 8, 0, 60, 1, 0 },
+ { "ATX +5V", 9, 0, 30, 1, 0 },
+ { "+3.3V", 10, 0, 20, 1, 0 },
+ { "5VSB", 11, 0, 30, 1, 0 },
+ { "CPU", 24, 1, 1, 1, 0 },
+ { "System", 25, 1, 1, 1, 0 },
+ { "PWM Phase1", 26, 1, 1, 1, 0 },
+ { "PWM Phase2", 27, 1, 1, 1, 0 },
+ { "PWM Phase3", 28, 1, 1, 1, 0 },
+ { "PWM Phase4", 29, 1, 1, 1, 0 },
+ { "PWM Phase5", 30, 1, 1, 1, 0 },
+ { "CPU Fan", 32, 2, 60, 1, 0 },
+ { "SYS Fan", 34, 2, 60, 1, 0 },
+ { "AUX1 Fan", 33, 2, 60, 1, 0 },
+ { "AUX2 Fan", 35, 2, 60, 1, 0 },
+ { "AUX3 Fan", 36, 2, 60, 1, 0 },
+ { NULL, 0, 0, 0, 0, 0 } }
+ },
+ { 0x001C, { "IX38 QuadGT", NULL }, {
+ { "CPU Core", 0, 0, 10, 1, 0 },
+ { "DDR2", 1, 0, 20, 1, 0 },
+ { "DDR2 VTT", 2, 0, 10, 1, 0 },
+ { "CPU VTT", 3, 0, 10, 1, 0 },
+ { "MCH 1.25V", 4, 0, 10, 1, 0 },
+ { "ICHIO 1.5V", 5, 0, 10, 1, 0 },
+ { "ICH 1.05V", 6, 0, 10, 1, 0 },
+ { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 },
+ { "ATX +12V (8-pin)", 8, 0, 60, 1, 0 },
+ { "ATX +5V", 9, 0, 30, 1, 0 },
+ { "+3.3V", 10, 0, 20, 1, 0 },
+ { "5VSB", 11, 0, 30, 1, 0 },
+ { "CPU", 24, 1, 1, 1, 0 },
+ { "System", 25, 1, 1, 1, 0 },
+ { "PWM Phase1", 26, 1, 1, 1, 0 },
+ { "PWM Phase2", 27, 1, 1, 1, 0 },
+ { "PWM Phase3", 28, 1, 1, 1, 0 },
+ { "PWM Phase4", 29, 1, 1, 1, 0 },
+ { "PWM Phase5", 30, 1, 1, 1, 0 },
+ { "CPU Fan", 32, 2, 60, 1, 0 },
+ { "SYS Fan", 34, 2, 60, 1, 0 },
+ { "AUX1 Fan", 33, 2, 60, 1, 0 },
+ { "AUX2 Fan", 35, 2, 60, 1, 0 },
+ { "AUX3 Fan", 36, 2, 60, 1, 0 },
+ { NULL, 0, 0, 0, 0, 0 } }
+ },
+ { 0x0000, { NULL }, { { NULL, 0, 0, 0, 0, 0 } } }
+};
+
+
+/* Insmod parameters */
+static bool force;
+module_param(force, bool, 0);
+MODULE_PARM_DESC(force, "Set to one to force detection.");
+/* Default verbose is 1, since this driver is still in the testing phase */
+static bool verbose = 1;
+module_param(verbose, bool, 0644);
+MODULE_PARM_DESC(verbose, "Enable/disable verbose error reporting");
+
+static const char *never_happen = "This should never happen.";
+static const char *report_this =
+ "Please report this to the abituguru3 maintainer (see MAINTAINERS)";
+
+/* wait while the uguru is busy (usually after a write) */
+static int abituguru3_wait_while_busy(struct abituguru3_data *data)
+{
+ u8 x;
+ int timeout = ABIT_UGURU3_WAIT_TIMEOUT;
+
+ while ((x = inb_p(data->addr + ABIT_UGURU3_DATA)) &
+ ABIT_UGURU3_STATUS_BUSY) {
+ timeout--;
+ if (timeout == 0)
+ return x;
+ /*
+ * sleep a bit before our last try, to give the uGuru3 one
+ * last chance to respond.
+ */
+ if (timeout == 1)
+ msleep(1);
+ }
+ return ABIT_UGURU3_SUCCESS;
+}
+
+/* wait till uguru is ready to be read */
+static int abituguru3_wait_for_read(struct abituguru3_data *data)
+{
+ u8 x;
+ int timeout = ABIT_UGURU3_WAIT_TIMEOUT;
+
+ while (!((x = inb_p(data->addr + ABIT_UGURU3_DATA)) &
+ ABIT_UGURU3_STATUS_READY_FOR_READ)) {
+ timeout--;
+ if (timeout == 0)
+ return x;
+ /*
+ * sleep a bit before our last try, to give the uGuru3 one
+ * last chance to respond.
+ */
+ if (timeout == 1)
+ msleep(1);
+ }
+ return ABIT_UGURU3_SUCCESS;
+}
+
+/*
+ * This synchronizes us with the uGuru3's protocol state machine, this
+ * must be done before each command.
+ */
+static int abituguru3_synchronize(struct abituguru3_data *data)
+{
+ int x, timeout = ABIT_UGURU3_SYNCHRONIZE_TIMEOUT;
+
+ x = abituguru3_wait_while_busy(data);
+ if (x != ABIT_UGURU3_SUCCESS) {
+ ABIT_UGURU3_DEBUG("synchronize timeout during initial busy "
+ "wait, status: 0x%02x\n", x);
+ return -EIO;
+ }
+
+ outb(0x20, data->addr + ABIT_UGURU3_DATA);
+ x = abituguru3_wait_while_busy(data);
+ if (x != ABIT_UGURU3_SUCCESS) {
+ ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x20, "
+ "status: 0x%02x\n", x);
+ return -EIO;
+ }
+
+ outb(0x10, data->addr + ABIT_UGURU3_CMD);
+ x = abituguru3_wait_while_busy(data);
+ if (x != ABIT_UGURU3_SUCCESS) {
+ ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x10, "
+ "status: 0x%02x\n", x);
+ return -EIO;
+ }
+
+ outb(0x00, data->addr + ABIT_UGURU3_CMD);
+ x = abituguru3_wait_while_busy(data);
+ if (x != ABIT_UGURU3_SUCCESS) {
+ ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x00, "
+ "status: 0x%02x\n", x);
+ return -EIO;
+ }
+
+ x = abituguru3_wait_for_read(data);
+ if (x != ABIT_UGURU3_SUCCESS) {
+ ABIT_UGURU3_DEBUG("synchronize timeout waiting for read, "
+ "status: 0x%02x\n", x);
+ return -EIO;
+ }
+
+ while ((x = inb(data->addr + ABIT_UGURU3_CMD)) != 0xAC) {
+ timeout--;
+ if (timeout == 0) {
+ ABIT_UGURU3_DEBUG("synchronize timeout cmd does not "
+ "hold 0xAC after synchronize, cmd: 0x%02x\n",
+ x);
+ return -EIO;
+ }
+ msleep(1);
+ }
+ return 0;
+}
+
+/*
+ * Read count bytes from sensor sensor_addr in bank bank_addr and store the
+ * result in buf
+ */
+static int abituguru3_read(struct abituguru3_data *data, u8 bank, u8 offset,
+ u8 count, u8 *buf)
+{
+ int i, x;
+
+ x = abituguru3_synchronize(data);
+ if (x)
+ return x;
+
+ outb(0x1A, data->addr + ABIT_UGURU3_DATA);
+ x = abituguru3_wait_while_busy(data);
+ if (x != ABIT_UGURU3_SUCCESS) {
+ ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after "
+ "sending 0x1A, status: 0x%02x\n", (unsigned int)bank,
+ (unsigned int)offset, x);
+ return -EIO;
+ }
+
+ outb(bank, data->addr + ABIT_UGURU3_CMD);
+ x = abituguru3_wait_while_busy(data);
+ if (x != ABIT_UGURU3_SUCCESS) {
+ ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after "
+ "sending the bank, status: 0x%02x\n",
+ (unsigned int)bank, (unsigned int)offset, x);
+ return -EIO;
+ }
+
+ outb(offset, data->addr + ABIT_UGURU3_CMD);
+ x = abituguru3_wait_while_busy(data);
+ if (x != ABIT_UGURU3_SUCCESS) {
+ ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after "
+ "sending the offset, status: 0x%02x\n",
+ (unsigned int)bank, (unsigned int)offset, x);
+ return -EIO;
+ }
+
+ outb(count, data->addr + ABIT_UGURU3_CMD);
+ x = abituguru3_wait_while_busy(data);
+ if (x != ABIT_UGURU3_SUCCESS) {
+ ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after "
+ "sending the count, status: 0x%02x\n",
+ (unsigned int)bank, (unsigned int)offset, x);
+ return -EIO;
+ }
+
+ for (i = 0; i < count; i++) {
+ x = abituguru3_wait_for_read(data);
+ if (x != ABIT_UGURU3_SUCCESS) {
+ ABIT_UGURU3_DEBUG("timeout reading byte %d from "
+ "0x%02x:0x%02x, status: 0x%02x\n", i,
+ (unsigned int)bank, (unsigned int)offset, x);
+ break;
+ }
+ buf[i] = inb(data->addr + ABIT_UGURU3_CMD);
+ }
+ return i;
+}
+
+/*
+ * Sensor settings are stored 1 byte per offset with the bytes
+ * placed add consecutive offsets.
+ */
+static int abituguru3_read_increment_offset(struct abituguru3_data *data,
+ u8 bank, u8 offset, u8 count,
+ u8 *buf, int offset_count)
+{
+ int i, x;
+
+ for (i = 0; i < offset_count; i++) {
+ x = abituguru3_read(data, bank, offset + i, count,
+ buf + i * count);
+ if (x != count) {
+ if (x < 0)
+ return x;
+ return i * count + x;
+ }
+ }
+
+ return i * count;
+}
+
+/*
+ * Following are the sysfs callback functions. These functions expect:
+ * sensor_device_attribute_2->index: index into the data->sensors array
+ * sensor_device_attribute_2->nr: register offset, bitmask or NA.
+ */
+static struct abituguru3_data *abituguru3_update_device(struct device *dev);
+
+static ssize_t show_value(struct device *dev,
+ struct device_attribute *devattr, char *buf)
+{
+ int value;
+ struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+ struct abituguru3_data *data = abituguru3_update_device(dev);
+ const struct abituguru3_sensor_info *sensor;
+
+ if (!data)
+ return -EIO;
+
+ sensor = &data->sensors[attr->index];
+
+ /* are we reading a setting, or is this a normal read? */
+ if (attr->nr)
+ value = data->settings[sensor->port][attr->nr];
+ else
+ value = data->value[sensor->port];
+
+ /* convert the value */
+ value = (value * sensor->multiplier) / sensor->divisor +
+ sensor->offset;
+
+ /*
+ * alternatively we could update the sensors settings struct for this,
+ * but then its contents would differ from the windows sw ini files
+ */
+ if (sensor->type == ABIT_UGURU3_TEMP_SENSOR)
+ value *= 1000;
+
+ return sprintf(buf, "%d\n", value);
+}
+
+static ssize_t show_alarm(struct device *dev,
+ struct device_attribute *devattr, char *buf)
+{
+ int port;
+ struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+ struct abituguru3_data *data = abituguru3_update_device(dev);
+
+ if (!data)
+ return -EIO;
+
+ port = data->sensors[attr->index].port;
+
+ /*
+ * See if the alarm bit for this sensor is set and if a bitmask is
+ * given in attr->nr also check if the alarm matches the type of alarm
+ * we're looking for (for volt it can be either low or high). The type
+ * is stored in a few readonly bits in the settings of the sensor.
+ */
+ if ((data->alarms[port / 8] & (0x01 << (port % 8))) &&
+ (!attr->nr || (data->settings[port][0] & attr->nr)))
+ return sprintf(buf, "1\n");
+ else
+ return sprintf(buf, "0\n");
+}
+
+static ssize_t show_mask(struct device *dev,
+ struct device_attribute *devattr, char *buf)
+{
+ struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+ struct abituguru3_data *data = dev_get_drvdata(dev);
+
+ if (data->settings[data->sensors[attr->index].port][0] & attr->nr)
+ return sprintf(buf, "1\n");
+ else
+ return sprintf(buf, "0\n");
+}
+
+static ssize_t show_label(struct device *dev,
+ struct device_attribute *devattr, char *buf)
+{
+ struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+ struct abituguru3_data *data = dev_get_drvdata(dev);
+
+ return sprintf(buf, "%s\n", data->sensors[attr->index].name);
+}
+
+static ssize_t show_name(struct device *dev,
+ struct device_attribute *devattr, char *buf)
+{
+ return sprintf(buf, "%s\n", ABIT_UGURU3_NAME);
+}
+
+/* Sysfs attr templates, the real entries are generated automatically. */
+static const
+struct sensor_device_attribute_2 abituguru3_sysfs_templ[3][10] = { {
+ SENSOR_ATTR_2(in%d_input, 0444, show_value, NULL, 0, 0),
+ SENSOR_ATTR_2(in%d_min, 0444, show_value, NULL, 1, 0),
+ SENSOR_ATTR_2(in%d_max, 0444, show_value, NULL, 2, 0),
+ SENSOR_ATTR_2(in%d_min_alarm, 0444, show_alarm, NULL,
+ ABIT_UGURU3_VOLT_LOW_ALARM_FLAG, 0),
+ SENSOR_ATTR_2(in%d_max_alarm, 0444, show_alarm, NULL,
+ ABIT_UGURU3_VOLT_HIGH_ALARM_FLAG, 0),
+ SENSOR_ATTR_2(in%d_beep, 0444, show_mask, NULL,
+ ABIT_UGURU3_BEEP_ENABLE, 0),
+ SENSOR_ATTR_2(in%d_shutdown, 0444, show_mask, NULL,
+ ABIT_UGURU3_SHUTDOWN_ENABLE, 0),
+ SENSOR_ATTR_2(in%d_min_alarm_enable, 0444, show_mask, NULL,
+ ABIT_UGURU3_VOLT_LOW_ALARM_ENABLE, 0),
+ SENSOR_ATTR_2(in%d_max_alarm_enable, 0444, show_mask, NULL,
+ ABIT_UGURU3_VOLT_HIGH_ALARM_ENABLE, 0),
+ SENSOR_ATTR_2(in%d_label, 0444, show_label, NULL, 0, 0)
+ }, {
+ SENSOR_ATTR_2(temp%d_input, 0444, show_value, NULL, 0, 0),
+ SENSOR_ATTR_2(temp%d_max, 0444, show_value, NULL, 1, 0),
+ SENSOR_ATTR_2(temp%d_crit, 0444, show_value, NULL, 2, 0),
+ SENSOR_ATTR_2(temp%d_alarm, 0444, show_alarm, NULL, 0, 0),
+ SENSOR_ATTR_2(temp%d_beep, 0444, show_mask, NULL,
+ ABIT_UGURU3_BEEP_ENABLE, 0),
+ SENSOR_ATTR_2(temp%d_shutdown, 0444, show_mask, NULL,
+ ABIT_UGURU3_SHUTDOWN_ENABLE, 0),
+ SENSOR_ATTR_2(temp%d_alarm_enable, 0444, show_mask, NULL,
+ ABIT_UGURU3_TEMP_HIGH_ALARM_ENABLE, 0),
+ SENSOR_ATTR_2(temp%d_label, 0444, show_label, NULL, 0, 0)
+ }, {
+ SENSOR_ATTR_2(fan%d_input, 0444, show_value, NULL, 0, 0),
+ SENSOR_ATTR_2(fan%d_min, 0444, show_value, NULL, 1, 0),
+ SENSOR_ATTR_2(fan%d_alarm, 0444, show_alarm, NULL, 0, 0),
+ SENSOR_ATTR_2(fan%d_beep, 0444, show_mask, NULL,
+ ABIT_UGURU3_BEEP_ENABLE, 0),
+ SENSOR_ATTR_2(fan%d_shutdown, 0444, show_mask, NULL,
+ ABIT_UGURU3_SHUTDOWN_ENABLE, 0),
+ SENSOR_ATTR_2(fan%d_alarm_enable, 0444, show_mask, NULL,
+ ABIT_UGURU3_FAN_LOW_ALARM_ENABLE, 0),
+ SENSOR_ATTR_2(fan%d_label, 0444, show_label, NULL, 0, 0)
+} };
+
+static struct sensor_device_attribute_2 abituguru3_sysfs_attr[] = {
+ SENSOR_ATTR_2(name, 0444, show_name, NULL, 0, 0),
+};
+
+static int abituguru3_probe(struct platform_device *pdev)
+{
+ const int no_sysfs_attr[3] = { 10, 8, 7 };
+ int sensor_index[3] = { 0, 1, 1 };
+ struct abituguru3_data *data;
+ int i, j, type, used, sysfs_names_free, sysfs_attr_i, res = -ENODEV;
+ char *sysfs_filename;
+ u8 buf[2];
+ u16 id;
+
+ data = devm_kzalloc(&pdev->dev, sizeof(struct abituguru3_data),
+ GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ data->addr = platform_get_resource(pdev, IORESOURCE_IO, 0)->start;
+ mutex_init(&data->update_lock);
+ platform_set_drvdata(pdev, data);
+
+ /* Read the motherboard ID */
+ i = abituguru3_read(data, ABIT_UGURU3_MISC_BANK, ABIT_UGURU3_BOARD_ID,
+ 2, buf);
+ if (i != 2)
+ goto abituguru3_probe_error;
+
+ /* Completely read the uGuru to see if one really is there */
+ if (!abituguru3_update_device(&pdev->dev))
+ goto abituguru3_probe_error;
+
+ /* lookup the ID in our motherboard table */
+ id = ((u16)buf[0] << 8) | (u16)buf[1];
+ for (i = 0; abituguru3_motherboards[i].id; i++)
+ if (abituguru3_motherboards[i].id == id)
+ break;
+ if (!abituguru3_motherboards[i].id) {
+ pr_err("error unknown motherboard ID: %04X. %s\n",
+ (unsigned int)id, report_this);
+ goto abituguru3_probe_error;
+ }
+ data->sensors = abituguru3_motherboards[i].sensors;
+
+ pr_info("found Abit uGuru3, motherboard ID: %04X\n", (unsigned int)id);
+
+ /* Fill the sysfs attr array */
+ sysfs_attr_i = 0;
+ sysfs_filename = data->sysfs_names;
+ sysfs_names_free = ABIT_UGURU3_SYSFS_NAMES_LENGTH;
+ for (i = 0; data->sensors[i].name; i++) {
+ /* Fail safe check, this should never happen! */
+ if (i >= ABIT_UGURU3_MAX_NO_SENSORS) {
+ pr_err("Fatal error motherboard has more sensors then ABIT_UGURU3_MAX_NO_SENSORS. %s %s\n",
+ never_happen, report_this);
+ res = -ENAMETOOLONG;
+ goto abituguru3_probe_error;
+ }
+ type = data->sensors[i].type;
+ for (j = 0; j < no_sysfs_attr[type]; j++) {
+ used = snprintf(sysfs_filename, sysfs_names_free,
+ abituguru3_sysfs_templ[type][j].dev_attr.attr.
+ name, sensor_index[type]) + 1;
+ data->sysfs_attr[sysfs_attr_i] =
+ abituguru3_sysfs_templ[type][j];
+ data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name =
+ sysfs_filename;
+ data->sysfs_attr[sysfs_attr_i].index = i;
+ sysfs_filename += used;
+ sysfs_names_free -= used;
+ sysfs_attr_i++;
+ }
+ sensor_index[type]++;
+ }
+ /* Fail safe check, this should never happen! */
+ if (sysfs_names_free < 0) {
+ pr_err("Fatal error ran out of space for sysfs attr names. %s %s\n",
+ never_happen, report_this);
+ res = -ENAMETOOLONG;
+ goto abituguru3_probe_error;
+ }
+
+ /* Register sysfs hooks */
+ for (i = 0; i < sysfs_attr_i; i++)
+ if (device_create_file(&pdev->dev,
+ &data->sysfs_attr[i].dev_attr))
+ goto abituguru3_probe_error;
+ for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++)
+ if (device_create_file(&pdev->dev,
+ &abituguru3_sysfs_attr[i].dev_attr))
+ goto abituguru3_probe_error;
+
+ data->hwmon_dev = hwmon_device_register(&pdev->dev);
+ if (IS_ERR(data->hwmon_dev)) {
+ res = PTR_ERR(data->hwmon_dev);
+ goto abituguru3_probe_error;
+ }
+
+ return 0; /* success */
+
+abituguru3_probe_error:
+ for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++)
+ device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr);
+ for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++)
+ device_remove_file(&pdev->dev,
+ &abituguru3_sysfs_attr[i].dev_attr);
+ return res;
+}
+
+static int abituguru3_remove(struct platform_device *pdev)
+{
+ int i;
+ struct abituguru3_data *data = platform_get_drvdata(pdev);
+
+ hwmon_device_unregister(data->hwmon_dev);
+ for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++)
+ device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr);
+ for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++)
+ device_remove_file(&pdev->dev,
+ &abituguru3_sysfs_attr[i].dev_attr);
+ return 0;
+}
+
+static struct abituguru3_data *abituguru3_update_device(struct device *dev)
+{
+ int i;
+ struct abituguru3_data *data = dev_get_drvdata(dev);
+
+ mutex_lock(&data->update_lock);
+ if (!data->valid || time_after(jiffies, data->last_updated + HZ)) {
+ /* Clear data->valid while updating */
+ data->valid = false;
+ /* Read alarms */
+ if (abituguru3_read_increment_offset(data,
+ ABIT_UGURU3_SETTINGS_BANK,
+ ABIT_UGURU3_ALARMS_START,
+ 1, data->alarms, 48/8) != (48/8))
+ goto LEAVE_UPDATE;
+ /* Read in and temp sensors (3 byte settings / sensor) */
+ for (i = 0; i < 32; i++) {
+ if (abituguru3_read(data, ABIT_UGURU3_SENSORS_BANK,
+ ABIT_UGURU3_VALUES_START + i,
+ 1, &data->value[i]) != 1)
+ goto LEAVE_UPDATE;
+ if (abituguru3_read_increment_offset(data,
+ ABIT_UGURU3_SETTINGS_BANK,
+ ABIT_UGURU3_SETTINGS_START + i * 3,
+ 1,
+ data->settings[i], 3) != 3)
+ goto LEAVE_UPDATE;
+ }
+ /* Read temp sensors (2 byte settings / sensor) */
+ for (i = 0; i < 16; i++) {
+ if (abituguru3_read(data, ABIT_UGURU3_SENSORS_BANK,
+ ABIT_UGURU3_VALUES_START + 32 + i,
+ 1, &data->value[32 + i]) != 1)
+ goto LEAVE_UPDATE;
+ if (abituguru3_read_increment_offset(data,
+ ABIT_UGURU3_SETTINGS_BANK,
+ ABIT_UGURU3_SETTINGS_START + 32 * 3 +
+ i * 2, 1,
+ data->settings[32 + i], 2) != 2)
+ goto LEAVE_UPDATE;
+ }
+ data->last_updated = jiffies;
+ data->valid = true;
+ }
+LEAVE_UPDATE:
+ mutex_unlock(&data->update_lock);
+ if (data->valid)
+ return data;
+ else
+ return NULL;
+}
+
+static int abituguru3_suspend(struct device *dev)
+{
+ struct abituguru3_data *data = dev_get_drvdata(dev);
+ /*
+ * make sure all communications with the uguru3 are done and no new
+ * ones are started
+ */
+ mutex_lock(&data->update_lock);
+ return 0;
+}
+
+static int abituguru3_resume(struct device *dev)
+{
+ struct abituguru3_data *data = dev_get_drvdata(dev);
+ mutex_unlock(&data->update_lock);
+ return 0;
+}
+
+static DEFINE_SIMPLE_DEV_PM_OPS(abituguru3_pm, abituguru3_suspend, abituguru3_resume);
+
+static struct platform_driver abituguru3_driver = {
+ .driver = {
+ .name = ABIT_UGURU3_NAME,
+ .pm = pm_sleep_ptr(&abituguru3_pm),
+ },
+ .probe = abituguru3_probe,
+ .remove = abituguru3_remove,
+};
+
+static int __init abituguru3_dmi_detect(void)
+{
+ const char *board_vendor, *board_name;
+ int i, err = (force) ? 1 : -ENODEV;
+ const char *const *dmi_name;
+ size_t sublen;
+
+ board_vendor = dmi_get_system_info(DMI_BOARD_VENDOR);
+ if (!board_vendor || strcmp(board_vendor, "http://www.abit.com.tw/"))
+ return err;
+
+ board_name = dmi_get_system_info(DMI_BOARD_NAME);
+ if (!board_name)
+ return err;
+
+ /*
+ * At the moment, we don't care about the part of the vendor
+ * DMI string contained in brackets. Truncate the string at
+ * the first occurrence of a bracket. Trim any trailing space
+ * from the substring.
+ */
+ sublen = strcspn(board_name, "(");
+ while (sublen > 0 && board_name[sublen - 1] == ' ')
+ sublen--;
+
+ for (i = 0; abituguru3_motherboards[i].id; i++) {
+ dmi_name = abituguru3_motherboards[i].dmi_name;
+ for ( ; *dmi_name; dmi_name++) {
+ if (strlen(*dmi_name) != sublen)
+ continue;
+ if (!strncasecmp(board_name, *dmi_name, sublen))
+ return 0;
+ }
+ }
+
+ /* No match found */
+ return 1;
+}
+
+/*
+ * FIXME: Manual detection should die eventually; we need to collect stable
+ * DMI model names first before we can rely entirely on CONFIG_DMI.
+ */
+
+static int __init abituguru3_detect(void)
+{
+ /*
+ * See if there is an uguru3 there. An idle uGuru3 will hold 0x00 or
+ * 0x08 at DATA and 0xAC at CMD. Sometimes the uGuru3 will hold 0x05
+ * or 0x55 at CMD instead, why is unknown.
+ */
+ u8 data_val = inb_p(ABIT_UGURU3_BASE + ABIT_UGURU3_DATA);
+ u8 cmd_val = inb_p(ABIT_UGURU3_BASE + ABIT_UGURU3_CMD);
+ if (((data_val == 0x00) || (data_val == 0x08)) &&
+ ((cmd_val == 0xAC) || (cmd_val == 0x05) ||
+ (cmd_val == 0x55)))
+ return 0;
+
+ ABIT_UGURU3_DEBUG("no Abit uGuru3 found, data = 0x%02X, cmd = "
+ "0x%02X\n", (unsigned int)data_val, (unsigned int)cmd_val);
+
+ if (force) {
+ pr_info("Assuming Abit uGuru3 is present because of \"force\" parameter\n");
+ return 0;
+ }
+
+ /* No uGuru3 found */
+ return -ENODEV;
+}
+
+static struct platform_device *abituguru3_pdev;
+
+static int __init abituguru3_init(void)
+{
+ struct resource res = { .flags = IORESOURCE_IO };
+ int err;
+
+ /* Attempt DMI detection first */
+ err = abituguru3_dmi_detect();
+ if (err < 0)
+ return err;
+
+ /*
+ * Fall back to manual detection if there was no exact
+ * board name match, or force was specified.
+ */
+ if (err > 0) {
+ err = abituguru3_detect();
+ if (err)
+ return err;
+
+ pr_warn("this motherboard was not detected using DMI. "
+ "Please send the output of \"dmidecode\" to the abituguru3 maintainer (see MAINTAINERS)\n");
+ }
+
+ err = platform_driver_register(&abituguru3_driver);
+ if (err)
+ goto exit;
+
+ abituguru3_pdev = platform_device_alloc(ABIT_UGURU3_NAME,
+ ABIT_UGURU3_BASE);
+ if (!abituguru3_pdev) {
+ pr_err("Device allocation failed\n");
+ err = -ENOMEM;
+ goto exit_driver_unregister;
+ }
+
+ res.start = ABIT_UGURU3_BASE;
+ res.end = ABIT_UGURU3_BASE + ABIT_UGURU3_REGION_LENGTH - 1;
+ res.name = ABIT_UGURU3_NAME;
+
+ err = platform_device_add_resources(abituguru3_pdev, &res, 1);
+ if (err) {
+ pr_err("Device resource addition failed (%d)\n", err);
+ goto exit_device_put;
+ }
+
+ err = platform_device_add(abituguru3_pdev);
+ if (err) {
+ pr_err("Device addition failed (%d)\n", err);
+ goto exit_device_put;
+ }
+
+ return 0;
+
+exit_device_put:
+ platform_device_put(abituguru3_pdev);
+exit_driver_unregister:
+ platform_driver_unregister(&abituguru3_driver);
+exit:
+ return err;
+}
+
+static void __exit abituguru3_exit(void)
+{
+ platform_device_unregister(abituguru3_pdev);
+ platform_driver_unregister(&abituguru3_driver);
+}
+
+MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>");
+MODULE_DESCRIPTION("Abit uGuru3 Sensor device");
+MODULE_LICENSE("GPL");
+
+module_init(abituguru3_init);
+module_exit(abituguru3_exit);