summaryrefslogtreecommitdiffstats
path: root/drivers/i2c/busses/i2c-nomadik.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/i2c/busses/i2c-nomadik.c')
-rw-r--r--drivers/i2c/busses/i2c-nomadik.c740
1 files changed, 432 insertions, 308 deletions
diff --git a/drivers/i2c/busses/i2c-nomadik.c b/drivers/i2c/busses/i2c-nomadik.c
index b10574d42b..4f41a3c782 100644
--- a/drivers/i2c/busses/i2c-nomadik.c
+++ b/drivers/i2c/busses/i2c-nomadik.c
@@ -6,21 +6,30 @@
* I2C master mode controller driver, used in Nomadik 8815
* and Ux500 platforms.
*
+ * The Mobileye EyeQ5 platform is also supported; it uses
+ * the same Ux500/DB8500 IP block with two quirks:
+ * - The memory bus only supports 32-bit accesses.
+ * - A register must be configured for the I2C speed mode;
+ * it is located in a shared register region called OLB.
+ *
* Author: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
* Author: Sachin Verma <sachin.verma@st.com>
*/
-#include <linux/init.h>
-#include <linux/module.h>
#include <linux/amba/bus.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/i2c.h>
-#include <linux/err.h>
+#include <linux/bitfield.h>
#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
#include <linux/io.h>
-#include <linux/pm_runtime.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
#include <linux/of.h>
#include <linux/pinctrl/consumer.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
#define DRIVER_NAME "nmk-i2c"
@@ -42,61 +51,63 @@
#define I2C_ICR (0x038)
/* Control registers */
-#define I2C_CR_PE (0x1 << 0) /* Peripheral Enable */
-#define I2C_CR_OM (0x3 << 1) /* Operating mode */
-#define I2C_CR_SAM (0x1 << 3) /* Slave addressing mode */
-#define I2C_CR_SM (0x3 << 4) /* Speed mode */
-#define I2C_CR_SGCM (0x1 << 6) /* Slave general call mode */
-#define I2C_CR_FTX (0x1 << 7) /* Flush Transmit */
-#define I2C_CR_FRX (0x1 << 8) /* Flush Receive */
-#define I2C_CR_DMA_TX_EN (0x1 << 9) /* DMA Tx enable */
-#define I2C_CR_DMA_RX_EN (0x1 << 10) /* DMA Rx Enable */
-#define I2C_CR_DMA_SLE (0x1 << 11) /* DMA sync. logic enable */
-#define I2C_CR_LM (0x1 << 12) /* Loopback mode */
-#define I2C_CR_FON (0x3 << 13) /* Filtering on */
-#define I2C_CR_FS (0x3 << 15) /* Force stop enable */
+#define I2C_CR_PE BIT(0) /* Peripheral Enable */
+#define I2C_CR_OM GENMASK(2, 1) /* Operating mode */
+#define I2C_CR_SAM BIT(3) /* Slave addressing mode */
+#define I2C_CR_SM GENMASK(5, 4) /* Speed mode */
+#define I2C_CR_SGCM BIT(6) /* Slave general call mode */
+#define I2C_CR_FTX BIT(7) /* Flush Transmit */
+#define I2C_CR_FRX BIT(8) /* Flush Receive */
+#define I2C_CR_DMA_TX_EN BIT(9) /* DMA Tx enable */
+#define I2C_CR_DMA_RX_EN BIT(10) /* DMA Rx Enable */
+#define I2C_CR_DMA_SLE BIT(11) /* DMA sync. logic enable */
+#define I2C_CR_LM BIT(12) /* Loopback mode */
+#define I2C_CR_FON GENMASK(14, 13) /* Filtering on */
+#define I2C_CR_FS GENMASK(16, 15) /* Force stop enable */
+
+/* Slave control register (SCR) */
+#define I2C_SCR_SLSU GENMASK(31, 16) /* Slave data setup time */
/* Master controller (MCR) register */
-#define I2C_MCR_OP (0x1 << 0) /* Operation */
-#define I2C_MCR_A7 (0x7f << 1) /* 7-bit address */
-#define I2C_MCR_EA10 (0x7 << 8) /* 10-bit Extended address */
-#define I2C_MCR_SB (0x1 << 11) /* Extended address */
-#define I2C_MCR_AM (0x3 << 12) /* Address type */
-#define I2C_MCR_STOP (0x1 << 14) /* Stop condition */
-#define I2C_MCR_LENGTH (0x7ff << 15) /* Transaction length */
+#define I2C_MCR_OP BIT(0) /* Operation */
+#define I2C_MCR_A7 GENMASK(7, 1) /* 7-bit address */
+#define I2C_MCR_EA10 GENMASK(10, 8) /* 10-bit Extended address */
+#define I2C_MCR_SB BIT(11) /* Extended address */
+#define I2C_MCR_AM GENMASK(13, 12) /* Address type */
+#define I2C_MCR_STOP BIT(14) /* Stop condition */
+#define I2C_MCR_LENGTH GENMASK(25, 15) /* Transaction length */
/* Status register (SR) */
-#define I2C_SR_OP (0x3 << 0) /* Operation */
-#define I2C_SR_STATUS (0x3 << 2) /* controller status */
-#define I2C_SR_CAUSE (0x7 << 4) /* Abort cause */
-#define I2C_SR_TYPE (0x3 << 7) /* Receive type */
-#define I2C_SR_LENGTH (0x7ff << 9) /* Transfer length */
+#define I2C_SR_OP GENMASK(1, 0) /* Operation */
+#define I2C_SR_STATUS GENMASK(3, 2) /* controller status */
+#define I2C_SR_CAUSE GENMASK(6, 4) /* Abort cause */
+#define I2C_SR_TYPE GENMASK(8, 7) /* Receive type */
+#define I2C_SR_LENGTH GENMASK(19, 9) /* Transfer length */
+
+/* Baud-rate counter register (BRCR) */
+#define I2C_BRCR_BRCNT1 GENMASK(31, 16) /* Baud-rate counter 1 */
+#define I2C_BRCR_BRCNT2 GENMASK(15, 0) /* Baud-rate counter 2 */
/* Interrupt mask set/clear (IMSCR) bits */
-#define I2C_IT_TXFE (0x1 << 0)
-#define I2C_IT_TXFNE (0x1 << 1)
-#define I2C_IT_TXFF (0x1 << 2)
-#define I2C_IT_TXFOVR (0x1 << 3)
-#define I2C_IT_RXFE (0x1 << 4)
-#define I2C_IT_RXFNF (0x1 << 5)
-#define I2C_IT_RXFF (0x1 << 6)
-#define I2C_IT_RFSR (0x1 << 16)
-#define I2C_IT_RFSE (0x1 << 17)
-#define I2C_IT_WTSR (0x1 << 18)
-#define I2C_IT_MTD (0x1 << 19)
-#define I2C_IT_STD (0x1 << 20)
-#define I2C_IT_MAL (0x1 << 24)
-#define I2C_IT_BERR (0x1 << 25)
-#define I2C_IT_MTDWS (0x1 << 28)
-
-#define GEN_MASK(val, mask, sb) (((val) << (sb)) & (mask))
+#define I2C_IT_TXFE BIT(0)
+#define I2C_IT_TXFNE BIT(1)
+#define I2C_IT_TXFF BIT(2)
+#define I2C_IT_TXFOVR BIT(3)
+#define I2C_IT_RXFE BIT(4)
+#define I2C_IT_RXFNF BIT(5)
+#define I2C_IT_RXFF BIT(6)
+#define I2C_IT_RFSR BIT(16)
+#define I2C_IT_RFSE BIT(17)
+#define I2C_IT_WTSR BIT(18)
+#define I2C_IT_MTD BIT(19)
+#define I2C_IT_STD BIT(20)
+#define I2C_IT_MAL BIT(24)
+#define I2C_IT_BERR BIT(25)
+#define I2C_IT_MTDWS BIT(28)
/* some bits in ICR are reserved */
#define I2C_CLEAR_ALL_INTS 0x131f007f
-/* first three msb bits are reserved */
-#define IRQ_MASK(mask) (mask & 0x1fffffff)
-
/* maximum threshold value */
#define MAX_I2C_FIFO_THRESHOLD 15
@@ -107,6 +118,15 @@ enum i2c_freq_mode {
I2C_FREQ_MODE_FAST_PLUS, /* up to 1 Mb/s */
};
+/* Mobileye EyeQ5 offset into a shared register region (called OLB) */
+#define NMK_I2C_EYEQ5_OLB_IOCR2 0x0B8
+
+enum i2c_eyeq5_speed {
+ I2C_EYEQ5_SPEED_FAST,
+ I2C_EYEQ5_SPEED_FAST_PLUS,
+ I2C_EYEQ5_SPEED_HIGH_SPEED,
+};
+
/**
* struct i2c_vendor_data - per-vendor variations
* @has_mtdws: variant has the MTDWS bit
@@ -131,6 +151,12 @@ enum i2c_operation {
I2C_READ = 0x01
};
+enum i2c_operating_mode {
+ I2C_OM_SLAVE,
+ I2C_OM_MASTER,
+ I2C_OM_MASTER_OR_SLAVE,
+};
+
/**
* struct i2c_nmk_client - client specific data
* @slave_adr: 7-bit slave address
@@ -159,11 +185,13 @@ struct i2c_nmk_client {
* @clk_freq: clock frequency for the operation mode
* @tft: Tx FIFO Threshold in bytes
* @rft: Rx FIFO Threshold in bytes
- * @timeout: Slave response timeout (ms)
+ * @timeout_usecs: Slave response timeout
* @sm: speed mode
* @stop: stop condition.
- * @xfer_complete: acknowledge completion for a I2C message.
+ * @xfer_wq: xfer done wait queue.
+ * @xfer_done: xfer done boolean.
* @result: controller propogated result.
+ * @has_32b_bus: controller is on a bus that only supports 32-bit accesses.
*/
struct nmk_i2c_dev {
struct i2c_vendor_data *vendor;
@@ -176,11 +204,13 @@ struct nmk_i2c_dev {
u32 clk_freq;
unsigned char tft;
unsigned char rft;
- int timeout;
+ u32 timeout_usecs;
enum i2c_freq_mode sm;
int stop;
- struct completion xfer_complete;
+ struct wait_queue_head xfer_wq;
+ bool xfer_done;
int result;
+ bool has_32b_bus;
};
/* controller's abort causes */
@@ -204,18 +234,36 @@ static inline void i2c_clr_bit(void __iomem *reg, u32 mask)
writel(readl(reg) & ~mask, reg);
}
+static inline u8 nmk_i2c_readb(const struct nmk_i2c_dev *priv,
+ unsigned long reg)
+{
+ if (priv->has_32b_bus)
+ return readl(priv->virtbase + reg);
+ else
+ return readb(priv->virtbase + reg);
+}
+
+static inline void nmk_i2c_writeb(const struct nmk_i2c_dev *priv, u32 val,
+ unsigned long reg)
+{
+ if (priv->has_32b_bus)
+ writel(val, priv->virtbase + reg);
+ else
+ writeb(val, priv->virtbase + reg);
+}
+
/**
* flush_i2c_fifo() - This function flushes the I2C FIFO
- * @dev: private data of I2C Driver
+ * @priv: private data of I2C Driver
*
* This function flushes the I2C Tx and Rx FIFOs. It returns
* 0 on successful flushing of FIFO
*/
-static int flush_i2c_fifo(struct nmk_i2c_dev *dev)
+static int flush_i2c_fifo(struct nmk_i2c_dev *priv)
{
#define LOOP_ATTEMPTS 10
+ ktime_t timeout;
int i;
- unsigned long timeout;
/*
* flush the transmit and receive FIFO. The flushing
@@ -224,19 +272,19 @@ static int flush_i2c_fifo(struct nmk_i2c_dev *dev)
* bits, until then no one must access Tx, Rx FIFO and
* should poll on these bits waiting for the completion.
*/
- writel((I2C_CR_FTX | I2C_CR_FRX), dev->virtbase + I2C_CR);
+ writel((I2C_CR_FTX | I2C_CR_FRX), priv->virtbase + I2C_CR);
for (i = 0; i < LOOP_ATTEMPTS; i++) {
- timeout = jiffies + dev->adap.timeout;
+ timeout = ktime_add_us(ktime_get(), priv->timeout_usecs);
- while (!time_after(jiffies, timeout)) {
- if ((readl(dev->virtbase + I2C_CR) &
+ while (ktime_after(timeout, ktime_get())) {
+ if ((readl(priv->virtbase + I2C_CR) &
(I2C_CR_FTX | I2C_CR_FRX)) == 0)
- return 0;
+ return 0;
}
}
- dev_err(&dev->adev->dev,
+ dev_err(&priv->adev->dev,
"flushing operation timed out giving up after %d attempts",
LOOP_ATTEMPTS);
@@ -245,120 +293,121 @@ static int flush_i2c_fifo(struct nmk_i2c_dev *dev)
/**
* disable_all_interrupts() - Disable all interrupts of this I2c Bus
- * @dev: private data of I2C Driver
+ * @priv: private data of I2C Driver
*/
-static void disable_all_interrupts(struct nmk_i2c_dev *dev)
+static void disable_all_interrupts(struct nmk_i2c_dev *priv)
{
- u32 mask = IRQ_MASK(0);
- writel(mask, dev->virtbase + I2C_IMSCR);
+ writel(0, priv->virtbase + I2C_IMSCR);
}
/**
* clear_all_interrupts() - Clear all interrupts of I2C Controller
- * @dev: private data of I2C Driver
+ * @priv: private data of I2C Driver
*/
-static void clear_all_interrupts(struct nmk_i2c_dev *dev)
+static void clear_all_interrupts(struct nmk_i2c_dev *priv)
{
- u32 mask;
- mask = IRQ_MASK(I2C_CLEAR_ALL_INTS);
- writel(mask, dev->virtbase + I2C_ICR);
+ writel(I2C_CLEAR_ALL_INTS, priv->virtbase + I2C_ICR);
}
/**
* init_hw() - initialize the I2C hardware
- * @dev: private data of I2C Driver
+ * @priv: private data of I2C Driver
*/
-static int init_hw(struct nmk_i2c_dev *dev)
+static int init_hw(struct nmk_i2c_dev *priv)
{
int stat;
- stat = flush_i2c_fifo(dev);
+ stat = flush_i2c_fifo(priv);
if (stat)
goto exit;
/* disable the controller */
- i2c_clr_bit(dev->virtbase + I2C_CR, I2C_CR_PE);
+ i2c_clr_bit(priv->virtbase + I2C_CR, I2C_CR_PE);
- disable_all_interrupts(dev);
+ disable_all_interrupts(priv);
- clear_all_interrupts(dev);
+ clear_all_interrupts(priv);
- dev->cli.operation = I2C_NO_OPERATION;
+ priv->cli.operation = I2C_NO_OPERATION;
exit:
return stat;
}
/* enable peripheral, master mode operation */
-#define DEFAULT_I2C_REG_CR ((1 << 1) | I2C_CR_PE)
+#define DEFAULT_I2C_REG_CR (FIELD_PREP(I2C_CR_OM, I2C_OM_MASTER) | I2C_CR_PE)
+
+/* grab top three bits from extended I2C addresses */
+#define ADR_3MSB_BITS GENMASK(9, 7)
/**
* load_i2c_mcr_reg() - load the MCR register
- * @dev: private data of controller
+ * @priv: private data of controller
* @flags: message flags
*/
-static u32 load_i2c_mcr_reg(struct nmk_i2c_dev *dev, u16 flags)
+static u32 load_i2c_mcr_reg(struct nmk_i2c_dev *priv, u16 flags)
{
u32 mcr = 0;
unsigned short slave_adr_3msb_bits;
- mcr |= GEN_MASK(dev->cli.slave_adr, I2C_MCR_A7, 1);
+ mcr |= FIELD_PREP(I2C_MCR_A7, priv->cli.slave_adr);
if (unlikely(flags & I2C_M_TEN)) {
/* 10-bit address transaction */
- mcr |= GEN_MASK(2, I2C_MCR_AM, 12);
+ mcr |= FIELD_PREP(I2C_MCR_AM, 2);
/*
* Get the top 3 bits.
* EA10 represents extended address in MCR. This includes
* the extension (MSB bits) of the 7 bit address loaded
* in A7
*/
- slave_adr_3msb_bits = (dev->cli.slave_adr >> 7) & 0x7;
+ slave_adr_3msb_bits = FIELD_GET(ADR_3MSB_BITS,
+ priv->cli.slave_adr);
- mcr |= GEN_MASK(slave_adr_3msb_bits, I2C_MCR_EA10, 8);
+ mcr |= FIELD_PREP(I2C_MCR_EA10, slave_adr_3msb_bits);
} else {
/* 7-bit address transaction */
- mcr |= GEN_MASK(1, I2C_MCR_AM, 12);
+ mcr |= FIELD_PREP(I2C_MCR_AM, 1);
}
/* start byte procedure not applied */
- mcr |= GEN_MASK(0, I2C_MCR_SB, 11);
+ mcr |= FIELD_PREP(I2C_MCR_SB, 0);
/* check the operation, master read/write? */
- if (dev->cli.operation == I2C_WRITE)
- mcr |= GEN_MASK(I2C_WRITE, I2C_MCR_OP, 0);
+ if (priv->cli.operation == I2C_WRITE)
+ mcr |= FIELD_PREP(I2C_MCR_OP, I2C_WRITE);
else
- mcr |= GEN_MASK(I2C_READ, I2C_MCR_OP, 0);
+ mcr |= FIELD_PREP(I2C_MCR_OP, I2C_READ);
/* stop or repeated start? */
- if (dev->stop)
- mcr |= GEN_MASK(1, I2C_MCR_STOP, 14);
+ if (priv->stop)
+ mcr |= FIELD_PREP(I2C_MCR_STOP, 1);
else
- mcr &= ~(GEN_MASK(1, I2C_MCR_STOP, 14));
+ mcr &= ~FIELD_PREP(I2C_MCR_STOP, 1);
- mcr |= GEN_MASK(dev->cli.count, I2C_MCR_LENGTH, 15);
+ mcr |= FIELD_PREP(I2C_MCR_LENGTH, priv->cli.count);
return mcr;
}
/**
* setup_i2c_controller() - setup the controller
- * @dev: private data of controller
+ * @priv: private data of controller
*/
-static void setup_i2c_controller(struct nmk_i2c_dev *dev)
+static void setup_i2c_controller(struct nmk_i2c_dev *priv)
{
u32 brcr1, brcr2;
u32 i2c_clk, div;
u32 ns;
u16 slsu;
- writel(0x0, dev->virtbase + I2C_CR);
- writel(0x0, dev->virtbase + I2C_HSMCR);
- writel(0x0, dev->virtbase + I2C_TFTR);
- writel(0x0, dev->virtbase + I2C_RFTR);
- writel(0x0, dev->virtbase + I2C_DMAR);
+ writel(0x0, priv->virtbase + I2C_CR);
+ writel(0x0, priv->virtbase + I2C_HSMCR);
+ writel(0x0, priv->virtbase + I2C_TFTR);
+ writel(0x0, priv->virtbase + I2C_RFTR);
+ writel(0x0, priv->virtbase + I2C_DMAR);
- i2c_clk = clk_get_rate(dev->clk);
+ i2c_clk = clk_get_rate(priv->clk);
/*
* set the slsu:
@@ -373,7 +422,7 @@ static void setup_i2c_controller(struct nmk_i2c_dev *dev)
* slsu = cycles / (1000000000 / f) + 1
*/
ns = DIV_ROUND_UP_ULL(1000000000ULL, i2c_clk);
- switch (dev->sm) {
+ switch (priv->sm) {
case I2C_FREQ_MODE_FAST:
case I2C_FREQ_MODE_FAST_PLUS:
slsu = DIV_ROUND_UP(100, ns); /* Fast */
@@ -388,15 +437,15 @@ static void setup_i2c_controller(struct nmk_i2c_dev *dev)
}
slsu += 1;
- dev_dbg(&dev->adev->dev, "calculated SLSU = %04x\n", slsu);
- writel(slsu << 16, dev->virtbase + I2C_SCR);
+ dev_dbg(&priv->adev->dev, "calculated SLSU = %04x\n", slsu);
+ writel(FIELD_PREP(I2C_SCR_SLSU, slsu), priv->virtbase + I2C_SCR);
/*
* The spec says, in case of std. mode the divider is
* 2 whereas it is 3 for fast and fastplus mode of
* operation. TODO - high speed support.
*/
- div = (dev->clk_freq > I2C_MAX_STANDARD_MODE_FREQ) ? 3 : 2;
+ div = (priv->clk_freq > I2C_MAX_STANDARD_MODE_FREQ) ? 3 : 2;
/*
* generate the mask for baud rate counters. The controller
@@ -405,11 +454,11 @@ static void setup_i2c_controller(struct nmk_i2c_dev *dev)
* plus operation. Currently we do not supprt high speed mode
* so set brcr1 to 0.
*/
- brcr1 = 0 << 16;
- brcr2 = (i2c_clk/(dev->clk_freq * div)) & 0xffff;
+ brcr1 = FIELD_PREP(I2C_BRCR_BRCNT1, 0);
+ brcr2 = FIELD_PREP(I2C_BRCR_BRCNT2, i2c_clk / (priv->clk_freq * div));
/* set the baud rate counter register */
- writel((brcr1 | brcr2), dev->virtbase + I2C_BRCR);
+ writel((brcr1 | brcr2), priv->virtbase + I2C_BRCR);
/*
* set the speed mode. Currently we support
@@ -417,125 +466,142 @@ static void setup_i2c_controller(struct nmk_i2c_dev *dev)
* TODO - support for fast mode plus (up to 1Mb/s)
* and high speed (up to 3.4 Mb/s)
*/
- if (dev->sm > I2C_FREQ_MODE_FAST) {
- dev_err(&dev->adev->dev,
+ if (priv->sm > I2C_FREQ_MODE_FAST) {
+ dev_err(&priv->adev->dev,
"do not support this mode defaulting to std. mode\n");
- brcr2 = i2c_clk / (I2C_MAX_STANDARD_MODE_FREQ * 2) & 0xffff;
- writel((brcr1 | brcr2), dev->virtbase + I2C_BRCR);
- writel(I2C_FREQ_MODE_STANDARD << 4,
- dev->virtbase + I2C_CR);
+ brcr2 = FIELD_PREP(I2C_BRCR_BRCNT2,
+ i2c_clk / (I2C_MAX_STANDARD_MODE_FREQ * 2));
+ writel((brcr1 | brcr2), priv->virtbase + I2C_BRCR);
+ writel(FIELD_PREP(I2C_CR_SM, I2C_FREQ_MODE_STANDARD),
+ priv->virtbase + I2C_CR);
}
- writel(dev->sm << 4, dev->virtbase + I2C_CR);
+ writel(FIELD_PREP(I2C_CR_SM, priv->sm), priv->virtbase + I2C_CR);
/* set the Tx and Rx FIFO threshold */
- writel(dev->tft, dev->virtbase + I2C_TFTR);
- writel(dev->rft, dev->virtbase + I2C_RFTR);
+ writel(priv->tft, priv->virtbase + I2C_TFTR);
+ writel(priv->rft, priv->virtbase + I2C_RFTR);
+}
+
+static bool nmk_i2c_wait_xfer_done(struct nmk_i2c_dev *priv)
+{
+ if (priv->timeout_usecs < jiffies_to_usecs(1)) {
+ unsigned long timeout_usecs = priv->timeout_usecs;
+ ktime_t timeout = ktime_set(0, timeout_usecs * NSEC_PER_USEC);
+
+ wait_event_hrtimeout(priv->xfer_wq, priv->xfer_done, timeout);
+ } else {
+ unsigned long timeout = usecs_to_jiffies(priv->timeout_usecs);
+
+ wait_event_timeout(priv->xfer_wq, priv->xfer_done, timeout);
+ }
+
+ return priv->xfer_done;
}
/**
* read_i2c() - Read from I2C client device
- * @dev: private data of I2C Driver
+ * @priv: private data of I2C Driver
* @flags: message flags
*
* This function reads from i2c client device when controller is in
* master mode. There is a completion timeout. If there is no transfer
* before timeout error is returned.
*/
-static int read_i2c(struct nmk_i2c_dev *dev, u16 flags)
+static int read_i2c(struct nmk_i2c_dev *priv, u16 flags)
{
- int status = 0;
u32 mcr, irq_mask;
- unsigned long timeout;
+ int status = 0;
+ bool xfer_done;
- mcr = load_i2c_mcr_reg(dev, flags);
- writel(mcr, dev->virtbase + I2C_MCR);
+ mcr = load_i2c_mcr_reg(priv, flags);
+ writel(mcr, priv->virtbase + I2C_MCR);
/* load the current CR value */
- writel(readl(dev->virtbase + I2C_CR) | DEFAULT_I2C_REG_CR,
- dev->virtbase + I2C_CR);
+ writel(readl(priv->virtbase + I2C_CR) | DEFAULT_I2C_REG_CR,
+ priv->virtbase + I2C_CR);
/* enable the controller */
- i2c_set_bit(dev->virtbase + I2C_CR, I2C_CR_PE);
+ i2c_set_bit(priv->virtbase + I2C_CR, I2C_CR_PE);
- init_completion(&dev->xfer_complete);
+ init_waitqueue_head(&priv->xfer_wq);
+ priv->xfer_done = false;
/* enable interrupts by setting the mask */
irq_mask = (I2C_IT_RXFNF | I2C_IT_RXFF |
I2C_IT_MAL | I2C_IT_BERR);
- if (dev->stop || !dev->vendor->has_mtdws)
+ if (priv->stop || !priv->vendor->has_mtdws)
irq_mask |= I2C_IT_MTD;
else
irq_mask |= I2C_IT_MTDWS;
- irq_mask = I2C_CLEAR_ALL_INTS & IRQ_MASK(irq_mask);
+ irq_mask &= I2C_CLEAR_ALL_INTS;
- writel(readl(dev->virtbase + I2C_IMSCR) | irq_mask,
- dev->virtbase + I2C_IMSCR);
+ writel(readl(priv->virtbase + I2C_IMSCR) | irq_mask,
+ priv->virtbase + I2C_IMSCR);
- timeout = wait_for_completion_timeout(
- &dev->xfer_complete, dev->adap.timeout);
+ xfer_done = nmk_i2c_wait_xfer_done(priv);
- if (timeout == 0) {
+ if (!xfer_done) {
/* Controller timed out */
- dev_err(&dev->adev->dev, "read from slave 0x%x timed out\n",
- dev->cli.slave_adr);
+ dev_err(&priv->adev->dev, "read from slave 0x%x timed out\n",
+ priv->cli.slave_adr);
status = -ETIMEDOUT;
}
return status;
}
-static void fill_tx_fifo(struct nmk_i2c_dev *dev, int no_bytes)
+static void fill_tx_fifo(struct nmk_i2c_dev *priv, int no_bytes)
{
int count;
for (count = (no_bytes - 2);
(count > 0) &&
- (dev->cli.count != 0);
+ (priv->cli.count != 0);
count--) {
/* write to the Tx FIFO */
- writeb(*dev->cli.buffer,
- dev->virtbase + I2C_TFR);
- dev->cli.buffer++;
- dev->cli.count--;
- dev->cli.xfer_bytes++;
+ nmk_i2c_writeb(priv, *priv->cli.buffer, I2C_TFR);
+ priv->cli.buffer++;
+ priv->cli.count--;
+ priv->cli.xfer_bytes++;
}
}
/**
* write_i2c() - Write data to I2C client.
- * @dev: private data of I2C Driver
+ * @priv: private data of I2C Driver
* @flags: message flags
*
* This function writes data to I2C client
*/
-static int write_i2c(struct nmk_i2c_dev *dev, u16 flags)
+static int write_i2c(struct nmk_i2c_dev *priv, u16 flags)
{
- u32 status = 0;
u32 mcr, irq_mask;
- unsigned long timeout;
+ u32 status = 0;
+ bool xfer_done;
- mcr = load_i2c_mcr_reg(dev, flags);
+ mcr = load_i2c_mcr_reg(priv, flags);
- writel(mcr, dev->virtbase + I2C_MCR);
+ writel(mcr, priv->virtbase + I2C_MCR);
/* load the current CR value */
- writel(readl(dev->virtbase + I2C_CR) | DEFAULT_I2C_REG_CR,
- dev->virtbase + I2C_CR);
+ writel(readl(priv->virtbase + I2C_CR) | DEFAULT_I2C_REG_CR,
+ priv->virtbase + I2C_CR);
/* enable the controller */
- i2c_set_bit(dev->virtbase + I2C_CR, I2C_CR_PE);
+ i2c_set_bit(priv->virtbase + I2C_CR, I2C_CR_PE);
- init_completion(&dev->xfer_complete);
+ init_waitqueue_head(&priv->xfer_wq);
+ priv->xfer_done = false;
/* enable interrupts by settings the masks */
irq_mask = (I2C_IT_TXFOVR | I2C_IT_MAL | I2C_IT_BERR);
/* Fill the TX FIFO with transmit data */
- fill_tx_fifo(dev, MAX_I2C_FIFO_THRESHOLD);
+ fill_tx_fifo(priv, MAX_I2C_FIFO_THRESHOLD);
- if (dev->cli.count != 0)
+ if (priv->cli.count != 0)
irq_mask |= I2C_IT_TXFNE;
/*
@@ -543,23 +609,22 @@ static int write_i2c(struct nmk_i2c_dev *dev, u16 flags)
* set the MTDWS bit (Master Transaction Done Without Stop)
* to start repeated start operation
*/
- if (dev->stop || !dev->vendor->has_mtdws)
+ if (priv->stop || !priv->vendor->has_mtdws)
irq_mask |= I2C_IT_MTD;
else
irq_mask |= I2C_IT_MTDWS;
- irq_mask = I2C_CLEAR_ALL_INTS & IRQ_MASK(irq_mask);
+ irq_mask &= I2C_CLEAR_ALL_INTS;
- writel(readl(dev->virtbase + I2C_IMSCR) | irq_mask,
- dev->virtbase + I2C_IMSCR);
+ writel(readl(priv->virtbase + I2C_IMSCR) | irq_mask,
+ priv->virtbase + I2C_IMSCR);
- timeout = wait_for_completion_timeout(
- &dev->xfer_complete, dev->adap.timeout);
+ xfer_done = nmk_i2c_wait_xfer_done(priv);
- if (timeout == 0) {
+ if (!xfer_done) {
/* Controller timed out */
- dev_err(&dev->adev->dev, "write to slave 0x%x timed out\n",
- dev->cli.slave_adr);
+ dev_err(&priv->adev->dev, "write to slave 0x%x timed out\n",
+ priv->cli.slave_adr);
status = -ETIMEDOUT;
}
@@ -568,44 +633,39 @@ static int write_i2c(struct nmk_i2c_dev *dev, u16 flags)
/**
* nmk_i2c_xfer_one() - transmit a single I2C message
- * @dev: device with a message encoded into it
+ * @priv: device with a message encoded into it
* @flags: message flags
*/
-static int nmk_i2c_xfer_one(struct nmk_i2c_dev *dev, u16 flags)
+static int nmk_i2c_xfer_one(struct nmk_i2c_dev *priv, u16 flags)
{
int status;
if (flags & I2C_M_RD) {
/* read operation */
- dev->cli.operation = I2C_READ;
- status = read_i2c(dev, flags);
+ priv->cli.operation = I2C_READ;
+ status = read_i2c(priv, flags);
} else {
/* write operation */
- dev->cli.operation = I2C_WRITE;
- status = write_i2c(dev, flags);
+ priv->cli.operation = I2C_WRITE;
+ status = write_i2c(priv, flags);
}
- if (status || (dev->result)) {
+ if (status || priv->result) {
u32 i2c_sr;
u32 cause;
- i2c_sr = readl(dev->virtbase + I2C_SR);
- /*
- * Check if the controller I2C operation status
- * is set to ABORT(11b).
- */
- if (((i2c_sr >> 2) & 0x3) == 0x3) {
- /* get the abort cause */
- cause = (i2c_sr >> 4) & 0x7;
- dev_err(&dev->adev->dev, "%s\n",
+ i2c_sr = readl(priv->virtbase + I2C_SR);
+ if (FIELD_GET(I2C_SR_STATUS, i2c_sr) == I2C_ABORT) {
+ cause = FIELD_GET(I2C_SR_CAUSE, i2c_sr);
+ dev_err(&priv->adev->dev, "%s\n",
cause >= ARRAY_SIZE(abort_causes) ?
"unknown reason" :
abort_causes[cause]);
}
- (void) init_hw(dev);
+ init_hw(priv);
- status = status ? status : dev->result;
+ status = status ? status : priv->result;
}
return status;
@@ -663,24 +723,24 @@ static int nmk_i2c_xfer(struct i2c_adapter *i2c_adap,
{
int status = 0;
int i;
- struct nmk_i2c_dev *dev = i2c_get_adapdata(i2c_adap);
+ struct nmk_i2c_dev *priv = i2c_get_adapdata(i2c_adap);
int j;
- pm_runtime_get_sync(&dev->adev->dev);
+ pm_runtime_get_sync(&priv->adev->dev);
/* Attempt three times to send the message queue */
for (j = 0; j < 3; j++) {
/* setup the i2c controller */
- setup_i2c_controller(dev);
+ setup_i2c_controller(priv);
for (i = 0; i < num_msgs; i++) {
- dev->cli.slave_adr = msgs[i].addr;
- dev->cli.buffer = msgs[i].buf;
- dev->cli.count = msgs[i].len;
- dev->stop = (i < (num_msgs - 1)) ? 0 : 1;
- dev->result = 0;
+ priv->cli.slave_adr = msgs[i].addr;
+ priv->cli.buffer = msgs[i].buf;
+ priv->cli.count = msgs[i].len;
+ priv->stop = (i < (num_msgs - 1)) ? 0 : 1;
+ priv->result = 0;
- status = nmk_i2c_xfer_one(dev, msgs[i].flags);
+ status = nmk_i2c_xfer_one(priv, msgs[i].flags);
if (status != 0)
break;
}
@@ -688,7 +748,7 @@ static int nmk_i2c_xfer(struct i2c_adapter *i2c_adap,
break;
}
- pm_runtime_put_sync(&dev->adev->dev);
+ pm_runtime_put_sync(&priv->adev->dev);
/* return the no. messages processed */
if (status)
@@ -699,14 +759,14 @@ static int nmk_i2c_xfer(struct i2c_adapter *i2c_adap,
/**
* disable_interrupts() - disable the interrupts
- * @dev: private data of controller
+ * @priv: private data of controller
* @irq: interrupt number
*/
-static int disable_interrupts(struct nmk_i2c_dev *dev, u32 irq)
+static int disable_interrupts(struct nmk_i2c_dev *priv, u32 irq)
{
- irq = IRQ_MASK(irq);
- writel(readl(dev->virtbase + I2C_IMSCR) & ~(I2C_CLEAR_ALL_INTS & irq),
- dev->virtbase + I2C_IMSCR);
+ irq &= I2C_CLEAR_ALL_INTS;
+ writel(readl(priv->virtbase + I2C_IMSCR) & ~irq,
+ priv->virtbase + I2C_IMSCR);
return 0;
}
@@ -723,38 +783,39 @@ static int disable_interrupts(struct nmk_i2c_dev *dev, u32 irq)
*/
static irqreturn_t i2c_irq_handler(int irq, void *arg)
{
- struct nmk_i2c_dev *dev = arg;
+ struct nmk_i2c_dev *priv = arg;
+ struct device *dev = &priv->adev->dev;
u32 tft, rft;
u32 count;
u32 misr, src;
/* load Tx FIFO and Rx FIFO threshold values */
- tft = readl(dev->virtbase + I2C_TFTR);
- rft = readl(dev->virtbase + I2C_RFTR);
+ tft = readl(priv->virtbase + I2C_TFTR);
+ rft = readl(priv->virtbase + I2C_RFTR);
/* read interrupt status register */
- misr = readl(dev->virtbase + I2C_MISR);
+ misr = readl(priv->virtbase + I2C_MISR);
src = __ffs(misr);
- switch ((1 << src)) {
+ switch (BIT(src)) {
/* Transmit FIFO nearly empty interrupt */
case I2C_IT_TXFNE:
{
- if (dev->cli.operation == I2C_READ) {
+ if (priv->cli.operation == I2C_READ) {
/*
* in read operation why do we care for writing?
* so disable the Transmit FIFO interrupt
*/
- disable_interrupts(dev, I2C_IT_TXFNE);
+ disable_interrupts(priv, I2C_IT_TXFNE);
} else {
- fill_tx_fifo(dev, (MAX_I2C_FIFO_THRESHOLD - tft));
+ fill_tx_fifo(priv, (MAX_I2C_FIFO_THRESHOLD - tft));
/*
* if done, close the transfer by disabling the
* corresponding TXFNE interrupt
*/
- if (dev->cli.count == 0)
- disable_interrupts(dev, I2C_IT_TXFNE);
+ if (priv->cli.count == 0)
+ disable_interrupts(priv, I2C_IT_TXFNE);
}
}
break;
@@ -768,60 +829,63 @@ static irqreturn_t i2c_irq_handler(int irq, void *arg)
case I2C_IT_RXFNF:
for (count = rft; count > 0; count--) {
/* Read the Rx FIFO */
- *dev->cli.buffer = readb(dev->virtbase + I2C_RFR);
- dev->cli.buffer++;
+ *priv->cli.buffer = nmk_i2c_readb(priv, I2C_RFR);
+ priv->cli.buffer++;
}
- dev->cli.count -= rft;
- dev->cli.xfer_bytes += rft;
+ priv->cli.count -= rft;
+ priv->cli.xfer_bytes += rft;
break;
/* Rx FIFO full */
case I2C_IT_RXFF:
for (count = MAX_I2C_FIFO_THRESHOLD; count > 0; count--) {
- *dev->cli.buffer = readb(dev->virtbase + I2C_RFR);
- dev->cli.buffer++;
+ *priv->cli.buffer = nmk_i2c_readb(priv, I2C_RFR);
+ priv->cli.buffer++;
}
- dev->cli.count -= MAX_I2C_FIFO_THRESHOLD;
- dev->cli.xfer_bytes += MAX_I2C_FIFO_THRESHOLD;
+ priv->cli.count -= MAX_I2C_FIFO_THRESHOLD;
+ priv->cli.xfer_bytes += MAX_I2C_FIFO_THRESHOLD;
break;
/* Master Transaction Done with/without stop */
case I2C_IT_MTD:
case I2C_IT_MTDWS:
- if (dev->cli.operation == I2C_READ) {
- while (!(readl(dev->virtbase + I2C_RISR)
+ if (priv->cli.operation == I2C_READ) {
+ while (!(readl(priv->virtbase + I2C_RISR)
& I2C_IT_RXFE)) {
- if (dev->cli.count == 0)
+ if (priv->cli.count == 0)
break;
- *dev->cli.buffer =
- readb(dev->virtbase + I2C_RFR);
- dev->cli.buffer++;
- dev->cli.count--;
- dev->cli.xfer_bytes++;
+ *priv->cli.buffer =
+ nmk_i2c_readb(priv, I2C_RFR);
+ priv->cli.buffer++;
+ priv->cli.count--;
+ priv->cli.xfer_bytes++;
}
}
- disable_all_interrupts(dev);
- clear_all_interrupts(dev);
+ disable_all_interrupts(priv);
+ clear_all_interrupts(priv);
- if (dev->cli.count) {
- dev->result = -EIO;
- dev_err(&dev->adev->dev,
- "%lu bytes still remain to be xfered\n",
- dev->cli.count);
- (void) init_hw(dev);
+ if (priv->cli.count) {
+ priv->result = -EIO;
+ dev_err(dev, "%lu bytes still remain to be xfered\n",
+ priv->cli.count);
+ init_hw(priv);
}
- complete(&dev->xfer_complete);
+ priv->xfer_done = true;
+ wake_up(&priv->xfer_wq);
+
break;
/* Master Arbitration lost interrupt */
case I2C_IT_MAL:
- dev->result = -EIO;
- (void) init_hw(dev);
+ priv->result = -EIO;
+ init_hw(priv);
+
+ i2c_set_bit(priv->virtbase + I2C_ICR, I2C_IT_MAL);
+ priv->xfer_done = true;
+ wake_up(&priv->xfer_wq);
- i2c_set_bit(dev->virtbase + I2C_ICR, I2C_IT_MAL);
- complete(&dev->xfer_complete);
break;
@@ -831,15 +895,20 @@ static irqreturn_t i2c_irq_handler(int irq, void *arg)
* during the transaction.
*/
case I2C_IT_BERR:
- dev->result = -EIO;
- /* get the status */
- if (((readl(dev->virtbase + I2C_SR) >> 2) & 0x3) == I2C_ABORT)
- (void) init_hw(dev);
+ {
+ u32 sr;
- i2c_set_bit(dev->virtbase + I2C_ICR, I2C_IT_BERR);
- complete(&dev->xfer_complete);
+ sr = readl(priv->virtbase + I2C_SR);
+ priv->result = -EIO;
+ if (FIELD_GET(I2C_SR_STATUS, sr) == I2C_ABORT)
+ init_hw(priv);
- break;
+ i2c_set_bit(priv->virtbase + I2C_ICR, I2C_IT_BERR);
+ priv->xfer_done = true;
+ wake_up(&priv->xfer_wq);
+
+ }
+ break;
/*
* Tx FIFO overrun interrupt.
@@ -847,11 +916,13 @@ static irqreturn_t i2c_irq_handler(int irq, void *arg)
* the Tx FIFO is full.
*/
case I2C_IT_TXFOVR:
- dev->result = -EIO;
- (void) init_hw(dev);
+ priv->result = -EIO;
+ init_hw(priv);
+
+ dev_err(dev, "Tx Fifo Over run\n");
+ priv->xfer_done = true;
+ wake_up(&priv->xfer_wq);
- dev_err(&dev->adev->dev, "Tx Fifo Over run\n");
- complete(&dev->xfer_complete);
break;
@@ -863,10 +934,10 @@ static irqreturn_t i2c_irq_handler(int irq, void *arg)
case I2C_IT_RFSE:
case I2C_IT_WTSR:
case I2C_IT_STD:
- dev_err(&dev->adev->dev, "unhandled Interrupt\n");
+ dev_err(dev, "unhandled Interrupt\n");
break;
default:
- dev_err(&dev->adev->dev, "spurious Interrupt..\n");
+ dev_err(dev, "spurious Interrupt..\n");
break;
}
@@ -893,9 +964,9 @@ static int nmk_i2c_resume_early(struct device *dev)
static int nmk_i2c_runtime_suspend(struct device *dev)
{
struct amba_device *adev = to_amba_device(dev);
- struct nmk_i2c_dev *nmk_i2c = amba_get_drvdata(adev);
+ struct nmk_i2c_dev *priv = amba_get_drvdata(adev);
- clk_disable_unprepare(nmk_i2c->clk);
+ clk_disable_unprepare(priv->clk);
pinctrl_pm_select_idle_state(dev);
return 0;
}
@@ -903,10 +974,10 @@ static int nmk_i2c_runtime_suspend(struct device *dev)
static int nmk_i2c_runtime_resume(struct device *dev)
{
struct amba_device *adev = to_amba_device(dev);
- struct nmk_i2c_dev *nmk_i2c = amba_get_drvdata(adev);
+ struct nmk_i2c_dev *priv = amba_get_drvdata(adev);
int ret;
- ret = clk_prepare_enable(nmk_i2c->clk);
+ ret = clk_prepare_enable(priv->clk);
if (ret) {
dev_err(dev, "can't prepare_enable clock\n");
return ret;
@@ -914,9 +985,9 @@ static int nmk_i2c_runtime_resume(struct device *dev)
pinctrl_pm_select_default_state(dev);
- ret = init_hw(nmk_i2c);
+ ret = init_hw(priv);
if (ret) {
- clk_disable_unprepare(nmk_i2c->clk);
+ clk_disable_unprepare(priv->clk);
pinctrl_pm_select_idle_state(dev);
}
@@ -939,107 +1010,160 @@ static const struct i2c_algorithm nmk_i2c_algo = {
};
static void nmk_i2c_of_probe(struct device_node *np,
- struct nmk_i2c_dev *nmk)
+ struct nmk_i2c_dev *priv)
{
+ u32 timeout_usecs;
+
/* Default to 100 kHz if no frequency is given in the node */
- if (of_property_read_u32(np, "clock-frequency", &nmk->clk_freq))
- nmk->clk_freq = I2C_MAX_STANDARD_MODE_FREQ;
+ if (of_property_read_u32(np, "clock-frequency", &priv->clk_freq))
+ priv->clk_freq = I2C_MAX_STANDARD_MODE_FREQ;
/* This driver only supports 'standard' and 'fast' modes of operation. */
- if (nmk->clk_freq <= I2C_MAX_STANDARD_MODE_FREQ)
- nmk->sm = I2C_FREQ_MODE_STANDARD;
+ if (priv->clk_freq <= I2C_MAX_STANDARD_MODE_FREQ)
+ priv->sm = I2C_FREQ_MODE_STANDARD;
+ else
+ priv->sm = I2C_FREQ_MODE_FAST;
+ priv->tft = 1; /* Tx FIFO threshold */
+ priv->rft = 8; /* Rx FIFO threshold */
+
+ /* Slave response timeout */
+ if (!of_property_read_u32(np, "i2c-transfer-timeout-us", &timeout_usecs))
+ priv->timeout_usecs = timeout_usecs;
+ else
+ priv->timeout_usecs = 200 * USEC_PER_MSEC;
+}
+
+static const unsigned int nmk_i2c_eyeq5_masks[] = {
+ GENMASK(5, 4),
+ GENMASK(7, 6),
+ GENMASK(9, 8),
+ GENMASK(11, 10),
+ GENMASK(13, 12),
+};
+
+static int nmk_i2c_eyeq5_probe(struct nmk_i2c_dev *priv)
+{
+ struct device *dev = &priv->adev->dev;
+ struct device_node *np = dev->of_node;
+ unsigned int mask, speed_mode;
+ struct regmap *olb;
+ unsigned int id;
+
+ priv->has_32b_bus = true;
+
+ olb = syscon_regmap_lookup_by_phandle_args(np, "mobileye,olb", 1, &id);
+ if (IS_ERR(olb))
+ return PTR_ERR(olb);
+ if (id >= ARRAY_SIZE(nmk_i2c_eyeq5_masks))
+ return -ENOENT;
+
+ if (priv->clk_freq <= 400000)
+ speed_mode = I2C_EYEQ5_SPEED_FAST;
+ else if (priv->clk_freq <= 1000000)
+ speed_mode = I2C_EYEQ5_SPEED_FAST_PLUS;
else
- nmk->sm = I2C_FREQ_MODE_FAST;
- nmk->tft = 1; /* Tx FIFO threshold */
- nmk->rft = 8; /* Rx FIFO threshold */
- nmk->timeout = 200; /* Slave response timeout(ms) */
+ speed_mode = I2C_EYEQ5_SPEED_HIGH_SPEED;
+
+ mask = nmk_i2c_eyeq5_masks[id];
+ regmap_update_bits(olb, NMK_I2C_EYEQ5_OLB_IOCR2,
+ mask, speed_mode << __fls(mask));
+
+ return 0;
}
static int nmk_i2c_probe(struct amba_device *adev, const struct amba_id *id)
{
int ret = 0;
+ struct nmk_i2c_dev *priv;
struct device_node *np = adev->dev.of_node;
- struct nmk_i2c_dev *dev;
+ struct device *dev = &adev->dev;
struct i2c_adapter *adap;
struct i2c_vendor_data *vendor = id->data;
u32 max_fifo_threshold = (vendor->fifodepth / 2) - 1;
- dev = devm_kzalloc(&adev->dev, sizeof(*dev), GFP_KERNEL);
- if (!dev)
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
return -ENOMEM;
- dev->vendor = vendor;
- dev->adev = adev;
- nmk_i2c_of_probe(np, dev);
+ priv->vendor = vendor;
+ priv->adev = adev;
+ priv->has_32b_bus = false;
+ nmk_i2c_of_probe(np, priv);
+
+ if (of_device_is_compatible(np, "mobileye,eyeq5-i2c")) {
+ ret = nmk_i2c_eyeq5_probe(priv);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed OLB lookup\n");
+ }
- if (dev->tft > max_fifo_threshold) {
- dev_warn(&adev->dev, "requested TX FIFO threshold %u, adjusted down to %u\n",
- dev->tft, max_fifo_threshold);
- dev->tft = max_fifo_threshold;
+ if (priv->tft > max_fifo_threshold) {
+ dev_warn(dev, "requested TX FIFO threshold %u, adjusted down to %u\n",
+ priv->tft, max_fifo_threshold);
+ priv->tft = max_fifo_threshold;
}
- if (dev->rft > max_fifo_threshold) {
- dev_warn(&adev->dev, "requested RX FIFO threshold %u, adjusted down to %u\n",
- dev->rft, max_fifo_threshold);
- dev->rft = max_fifo_threshold;
+ if (priv->rft > max_fifo_threshold) {
+ dev_warn(dev, "requested RX FIFO threshold %u, adjusted down to %u\n",
+ priv->rft, max_fifo_threshold);
+ priv->rft = max_fifo_threshold;
}
- amba_set_drvdata(adev, dev);
+ amba_set_drvdata(adev, priv);
- dev->virtbase = devm_ioremap(&adev->dev, adev->res.start,
- resource_size(&adev->res));
- if (!dev->virtbase)
+ priv->virtbase = devm_ioremap(dev, adev->res.start,
+ resource_size(&adev->res));
+ if (!priv->virtbase)
return -ENOMEM;
- dev->irq = adev->irq[0];
- ret = devm_request_irq(&adev->dev, dev->irq, i2c_irq_handler, 0,
- DRIVER_NAME, dev);
+ priv->irq = adev->irq[0];
+ ret = devm_request_irq(dev, priv->irq, i2c_irq_handler, 0,
+ DRIVER_NAME, priv);
if (ret)
- return dev_err_probe(&adev->dev, ret,
- "cannot claim the irq %d\n", dev->irq);
+ return dev_err_probe(dev, ret,
+ "cannot claim the irq %d\n", priv->irq);
- dev->clk = devm_clk_get_enabled(&adev->dev, NULL);
- if (IS_ERR(dev->clk))
- return dev_err_probe(&adev->dev, PTR_ERR(dev->clk),
+ priv->clk = devm_clk_get_enabled(dev, NULL);
+ if (IS_ERR(priv->clk))
+ return dev_err_probe(dev, PTR_ERR(priv->clk),
"could enable i2c clock\n");
- init_hw(dev);
+ init_hw(priv);
- adap = &dev->adap;
+ adap = &priv->adap;
adap->dev.of_node = np;
- adap->dev.parent = &adev->dev;
+ adap->dev.parent = dev;
adap->owner = THIS_MODULE;
adap->class = I2C_CLASS_DEPRECATED;
adap->algo = &nmk_i2c_algo;
- adap->timeout = msecs_to_jiffies(dev->timeout);
+ adap->timeout = usecs_to_jiffies(priv->timeout_usecs);
snprintf(adap->name, sizeof(adap->name),
"Nomadik I2C at %pR", &adev->res);
- i2c_set_adapdata(adap, dev);
+ i2c_set_adapdata(adap, priv);
- dev_info(&adev->dev,
+ dev_info(dev,
"initialize %s on virtual base %p\n",
- adap->name, dev->virtbase);
+ adap->name, priv->virtbase);
ret = i2c_add_adapter(adap);
if (ret)
return ret;
- pm_runtime_put(&adev->dev);
+ pm_runtime_put(dev);
return 0;
}
static void nmk_i2c_remove(struct amba_device *adev)
{
- struct nmk_i2c_dev *dev = amba_get_drvdata(adev);
+ struct nmk_i2c_dev *priv = amba_get_drvdata(adev);
- i2c_del_adapter(&dev->adap);
- flush_i2c_fifo(dev);
- disable_all_interrupts(dev);
- clear_all_interrupts(dev);
+ i2c_del_adapter(&priv->adap);
+ flush_i2c_fifo(priv);
+ disable_all_interrupts(priv);
+ clear_all_interrupts(priv);
/* disable the controller */
- i2c_clr_bit(dev->virtbase + I2C_CR, I2C_CR_PE);
+ i2c_clr_bit(priv->virtbase + I2C_CR, I2C_CR_PE);
}
static struct i2c_vendor_data vendor_stn8815 = {