diff options
Diffstat (limited to 'drivers/iio/adc/bcm_iproc_adc.c')
-rw-r--r-- | drivers/iio/adc/bcm_iproc_adc.c | 627 |
1 files changed, 627 insertions, 0 deletions
diff --git a/drivers/iio/adc/bcm_iproc_adc.c b/drivers/iio/adc/bcm_iproc_adc.c new file mode 100644 index 0000000000..0d6885413a --- /dev/null +++ b/drivers/iio/adc/bcm_iproc_adc.c @@ -0,0 +1,627 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright 2016 Broadcom + */ + +#include <linux/module.h> +#include <linux/mod_devicetable.h> +#include <linux/io.h> +#include <linux/clk.h> +#include <linux/mfd/syscon.h> +#include <linux/regmap.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/platform_device.h> + +#include <linux/iio/iio.h> + +/* Below Register's are common to IPROC ADC and Touchscreen IP */ +#define IPROC_REGCTL1 0x00 +#define IPROC_REGCTL2 0x04 +#define IPROC_INTERRUPT_THRES 0x08 +#define IPROC_INTERRUPT_MASK 0x0c +#define IPROC_INTERRUPT_STATUS 0x10 +#define IPROC_ANALOG_CONTROL 0x1c +#define IPROC_CONTROLLER_STATUS 0x14 +#define IPROC_AUX_DATA 0x20 +#define IPROC_SOFT_BYPASS_CONTROL 0x38 +#define IPROC_SOFT_BYPASS_DATA 0x3C + +/* IPROC ADC Channel register offsets */ +#define IPROC_ADC_CHANNEL_REGCTL1 0x800 +#define IPROC_ADC_CHANNEL_REGCTL2 0x804 +#define IPROC_ADC_CHANNEL_STATUS 0x808 +#define IPROC_ADC_CHANNEL_INTERRUPT_STATUS 0x80c +#define IPROC_ADC_CHANNEL_INTERRUPT_MASK 0x810 +#define IPROC_ADC_CHANNEL_DATA 0x814 +#define IPROC_ADC_CHANNEL_OFFSET 0x20 + +/* Bit definitions for IPROC_REGCTL2 */ +#define IPROC_ADC_AUXIN_SCAN_ENA BIT(0) +#define IPROC_ADC_PWR_LDO BIT(5) +#define IPROC_ADC_PWR_ADC BIT(4) +#define IPROC_ADC_PWR_BG BIT(3) +#define IPROC_ADC_CONTROLLER_EN BIT(17) + +/* Bit definitions for IPROC_INTERRUPT_MASK and IPROC_INTERRUPT_STATUS */ +#define IPROC_ADC_AUXDATA_RDY_INTR BIT(3) +#define IPROC_ADC_INTR 9 +#define IPROC_ADC_INTR_MASK (0xFF << IPROC_ADC_INTR) + +/* Bit definitions for IPROC_ANALOG_CONTROL */ +#define IPROC_ADC_CHANNEL_SEL 11 +#define IPROC_ADC_CHANNEL_SEL_MASK (0x7 << IPROC_ADC_CHANNEL_SEL) + +/* Bit definitions for IPROC_ADC_CHANNEL_REGCTL1 */ +#define IPROC_ADC_CHANNEL_ROUNDS 0x2 +#define IPROC_ADC_CHANNEL_ROUNDS_MASK (0x3F << IPROC_ADC_CHANNEL_ROUNDS) +#define IPROC_ADC_CHANNEL_MODE 0x1 +#define IPROC_ADC_CHANNEL_MODE_MASK (0x1 << IPROC_ADC_CHANNEL_MODE) +#define IPROC_ADC_CHANNEL_MODE_TDM 0x1 +#define IPROC_ADC_CHANNEL_MODE_SNAPSHOT 0x0 +#define IPROC_ADC_CHANNEL_ENABLE 0x0 +#define IPROC_ADC_CHANNEL_ENABLE_MASK 0x1 + +/* Bit definitions for IPROC_ADC_CHANNEL_REGCTL2 */ +#define IPROC_ADC_CHANNEL_WATERMARK 0x0 +#define IPROC_ADC_CHANNEL_WATERMARK_MASK \ + (0x3F << IPROC_ADC_CHANNEL_WATERMARK) + +#define IPROC_ADC_WATER_MARK_LEVEL 0x1 + +/* Bit definitions for IPROC_ADC_CHANNEL_STATUS */ +#define IPROC_ADC_CHANNEL_DATA_LOST 0x0 +#define IPROC_ADC_CHANNEL_DATA_LOST_MASK \ + (0x0 << IPROC_ADC_CHANNEL_DATA_LOST) +#define IPROC_ADC_CHANNEL_VALID_ENTERIES 0x1 +#define IPROC_ADC_CHANNEL_VALID_ENTERIES_MASK \ + (0xFF << IPROC_ADC_CHANNEL_VALID_ENTERIES) +#define IPROC_ADC_CHANNEL_TOTAL_ENTERIES 0x9 +#define IPROC_ADC_CHANNEL_TOTAL_ENTERIES_MASK \ + (0xFF << IPROC_ADC_CHANNEL_TOTAL_ENTERIES) + +/* Bit definitions for IPROC_ADC_CHANNEL_INTERRUPT_MASK */ +#define IPROC_ADC_CHANNEL_WTRMRK_INTR 0x0 +#define IPROC_ADC_CHANNEL_WTRMRK_INTR_MASK \ + (0x1 << IPROC_ADC_CHANNEL_WTRMRK_INTR) +#define IPROC_ADC_CHANNEL_FULL_INTR 0x1 +#define IPROC_ADC_CHANNEL_FULL_INTR_MASK \ + (0x1 << IPROC_ADC_IPROC_ADC_CHANNEL_FULL_INTR) +#define IPROC_ADC_CHANNEL_EMPTY_INTR 0x2 +#define IPROC_ADC_CHANNEL_EMPTY_INTR_MASK \ + (0x1 << IPROC_ADC_CHANNEL_EMPTY_INTR) + +#define IPROC_ADC_WATER_MARK_INTR_ENABLE 0x1 + +/* Number of time to retry a set of the interrupt mask reg */ +#define IPROC_ADC_INTMASK_RETRY_ATTEMPTS 10 + +#define IPROC_ADC_READ_TIMEOUT (HZ*2) + +#define iproc_adc_dbg_reg(dev, priv, reg) \ +do { \ + u32 val; \ + regmap_read(priv->regmap, reg, &val); \ + dev_dbg(dev, "%20s= 0x%08x\n", #reg, val); \ +} while (0) + +struct iproc_adc_priv { + struct regmap *regmap; + struct clk *adc_clk; + struct mutex mutex; + int irqno; + int chan_val; + int chan_id; + struct completion completion; +}; + +static void iproc_adc_reg_dump(struct iio_dev *indio_dev) +{ + struct device *dev = &indio_dev->dev; + struct iproc_adc_priv *adc_priv = iio_priv(indio_dev); + + iproc_adc_dbg_reg(dev, adc_priv, IPROC_REGCTL1); + iproc_adc_dbg_reg(dev, adc_priv, IPROC_REGCTL2); + iproc_adc_dbg_reg(dev, adc_priv, IPROC_INTERRUPT_THRES); + iproc_adc_dbg_reg(dev, adc_priv, IPROC_INTERRUPT_MASK); + iproc_adc_dbg_reg(dev, adc_priv, IPROC_INTERRUPT_STATUS); + iproc_adc_dbg_reg(dev, adc_priv, IPROC_CONTROLLER_STATUS); + iproc_adc_dbg_reg(dev, adc_priv, IPROC_ANALOG_CONTROL); + iproc_adc_dbg_reg(dev, adc_priv, IPROC_AUX_DATA); + iproc_adc_dbg_reg(dev, adc_priv, IPROC_SOFT_BYPASS_CONTROL); + iproc_adc_dbg_reg(dev, adc_priv, IPROC_SOFT_BYPASS_DATA); +} + +static irqreturn_t iproc_adc_interrupt_thread(int irq, void *data) +{ + u32 channel_intr_status; + u32 intr_status; + u32 intr_mask; + struct iio_dev *indio_dev = data; + struct iproc_adc_priv *adc_priv = iio_priv(indio_dev); + + /* + * This interrupt is shared with the touchscreen driver. + * Make sure this interrupt is intended for us. + * Handle only ADC channel specific interrupts. + */ + regmap_read(adc_priv->regmap, IPROC_INTERRUPT_STATUS, &intr_status); + regmap_read(adc_priv->regmap, IPROC_INTERRUPT_MASK, &intr_mask); + intr_status = intr_status & intr_mask; + channel_intr_status = (intr_status & IPROC_ADC_INTR_MASK) >> + IPROC_ADC_INTR; + if (channel_intr_status) + return IRQ_WAKE_THREAD; + + return IRQ_NONE; +} + +static irqreturn_t iproc_adc_interrupt_handler(int irq, void *data) +{ + irqreturn_t retval = IRQ_NONE; + struct iproc_adc_priv *adc_priv; + struct iio_dev *indio_dev = data; + unsigned int valid_entries; + u32 intr_status; + u32 intr_channels; + u32 channel_status; + u32 ch_intr_status; + + adc_priv = iio_priv(indio_dev); + + regmap_read(adc_priv->regmap, IPROC_INTERRUPT_STATUS, &intr_status); + dev_dbg(&indio_dev->dev, "iproc_adc_interrupt_handler(),INTRPT_STS:%x\n", + intr_status); + + intr_channels = (intr_status & IPROC_ADC_INTR_MASK) >> IPROC_ADC_INTR; + if (intr_channels) { + regmap_read(adc_priv->regmap, + IPROC_ADC_CHANNEL_INTERRUPT_STATUS + + IPROC_ADC_CHANNEL_OFFSET * adc_priv->chan_id, + &ch_intr_status); + + if (ch_intr_status & IPROC_ADC_CHANNEL_WTRMRK_INTR_MASK) { + regmap_read(adc_priv->regmap, + IPROC_ADC_CHANNEL_STATUS + + IPROC_ADC_CHANNEL_OFFSET * + adc_priv->chan_id, + &channel_status); + + valid_entries = ((channel_status & + IPROC_ADC_CHANNEL_VALID_ENTERIES_MASK) >> + IPROC_ADC_CHANNEL_VALID_ENTERIES); + if (valid_entries >= 1) { + regmap_read(adc_priv->regmap, + IPROC_ADC_CHANNEL_DATA + + IPROC_ADC_CHANNEL_OFFSET * + adc_priv->chan_id, + &adc_priv->chan_val); + complete(&adc_priv->completion); + } else { + dev_err(&indio_dev->dev, + "No data rcvd on channel %d\n", + adc_priv->chan_id); + } + regmap_write(adc_priv->regmap, + IPROC_ADC_CHANNEL_INTERRUPT_MASK + + IPROC_ADC_CHANNEL_OFFSET * + adc_priv->chan_id, + (ch_intr_status & + ~(IPROC_ADC_CHANNEL_WTRMRK_INTR_MASK))); + } + regmap_write(adc_priv->regmap, + IPROC_ADC_CHANNEL_INTERRUPT_STATUS + + IPROC_ADC_CHANNEL_OFFSET * adc_priv->chan_id, + ch_intr_status); + regmap_write(adc_priv->regmap, IPROC_INTERRUPT_STATUS, + intr_channels); + retval = IRQ_HANDLED; + } + + return retval; +} + +static int iproc_adc_do_read(struct iio_dev *indio_dev, + int channel, + u16 *p_adc_data) +{ + int read_len = 0; + u32 val; + u32 mask; + u32 val_check; + int failed_cnt = 0; + struct iproc_adc_priv *adc_priv = iio_priv(indio_dev); + + mutex_lock(&adc_priv->mutex); + + /* + * After a read is complete the ADC interrupts will be disabled so + * we can assume this section of code is safe from interrupts. + */ + adc_priv->chan_val = -1; + adc_priv->chan_id = channel; + + reinit_completion(&adc_priv->completion); + /* Clear any pending interrupt */ + regmap_update_bits(adc_priv->regmap, IPROC_INTERRUPT_STATUS, + IPROC_ADC_INTR_MASK | IPROC_ADC_AUXDATA_RDY_INTR, + ((0x0 << channel) << IPROC_ADC_INTR) | + IPROC_ADC_AUXDATA_RDY_INTR); + + /* Configure channel for snapshot mode and enable */ + val = (BIT(IPROC_ADC_CHANNEL_ROUNDS) | + (IPROC_ADC_CHANNEL_MODE_SNAPSHOT << IPROC_ADC_CHANNEL_MODE) | + (0x1 << IPROC_ADC_CHANNEL_ENABLE)); + + mask = IPROC_ADC_CHANNEL_ROUNDS_MASK | IPROC_ADC_CHANNEL_MODE_MASK | + IPROC_ADC_CHANNEL_ENABLE_MASK; + regmap_update_bits(adc_priv->regmap, (IPROC_ADC_CHANNEL_REGCTL1 + + IPROC_ADC_CHANNEL_OFFSET * channel), + mask, val); + + /* Set the Watermark for a channel */ + regmap_update_bits(adc_priv->regmap, (IPROC_ADC_CHANNEL_REGCTL2 + + IPROC_ADC_CHANNEL_OFFSET * channel), + IPROC_ADC_CHANNEL_WATERMARK_MASK, + 0x1); + + /* Enable water mark interrupt */ + regmap_update_bits(adc_priv->regmap, (IPROC_ADC_CHANNEL_INTERRUPT_MASK + + IPROC_ADC_CHANNEL_OFFSET * + channel), + IPROC_ADC_CHANNEL_WTRMRK_INTR_MASK, + IPROC_ADC_WATER_MARK_INTR_ENABLE); + regmap_read(adc_priv->regmap, IPROC_INTERRUPT_MASK, &val); + + /* Enable ADC interrupt for a channel */ + val |= (BIT(channel) << IPROC_ADC_INTR); + regmap_write(adc_priv->regmap, IPROC_INTERRUPT_MASK, val); + + /* + * There seems to be a very rare issue where writing to this register + * does not take effect. To work around the issue we will try multiple + * writes. In total we will spend about 10*10 = 100 us attempting this. + * Testing has shown that this may loop a few time, but we have never + * hit the full count. + */ + regmap_read(adc_priv->regmap, IPROC_INTERRUPT_MASK, &val_check); + while (val_check != val) { + failed_cnt++; + + if (failed_cnt > IPROC_ADC_INTMASK_RETRY_ATTEMPTS) + break; + + udelay(10); + regmap_update_bits(adc_priv->regmap, IPROC_INTERRUPT_MASK, + IPROC_ADC_INTR_MASK, + ((0x1 << channel) << + IPROC_ADC_INTR)); + + regmap_read(adc_priv->regmap, IPROC_INTERRUPT_MASK, &val_check); + } + + if (failed_cnt) { + dev_dbg(&indio_dev->dev, + "IntMask failed (%d times)", failed_cnt); + if (failed_cnt > IPROC_ADC_INTMASK_RETRY_ATTEMPTS) { + dev_err(&indio_dev->dev, + "IntMask set failed. Read will likely fail."); + read_len = -EIO; + goto adc_err; + } + } + regmap_read(adc_priv->regmap, IPROC_INTERRUPT_MASK, &val_check); + + if (wait_for_completion_timeout(&adc_priv->completion, + IPROC_ADC_READ_TIMEOUT) > 0) { + + /* Only the lower 16 bits are relevant */ + *p_adc_data = adc_priv->chan_val & 0xFFFF; + read_len = sizeof(*p_adc_data); + + } else { + /* + * We never got the interrupt, something went wrong. + * Perhaps the interrupt may still be coming, we do not want + * that now. Lets disable the ADC interrupt, and clear the + * status to put it back in to normal state. + */ + read_len = -ETIMEDOUT; + goto adc_err; + } + mutex_unlock(&adc_priv->mutex); + + return read_len; + +adc_err: + regmap_update_bits(adc_priv->regmap, IPROC_INTERRUPT_MASK, + IPROC_ADC_INTR_MASK, + ((0x0 << channel) << IPROC_ADC_INTR)); + + regmap_update_bits(adc_priv->regmap, IPROC_INTERRUPT_STATUS, + IPROC_ADC_INTR_MASK, + ((0x0 << channel) << IPROC_ADC_INTR)); + + dev_err(&indio_dev->dev, "Timed out waiting for ADC data!\n"); + iproc_adc_reg_dump(indio_dev); + mutex_unlock(&adc_priv->mutex); + + return read_len; +} + +static int iproc_adc_enable(struct iio_dev *indio_dev) +{ + u32 val; + u32 channel_id; + struct iproc_adc_priv *adc_priv = iio_priv(indio_dev); + int ret; + + /* Set i_amux = 3b'000, select channel 0 */ + ret = regmap_update_bits(adc_priv->regmap, IPROC_ANALOG_CONTROL, + IPROC_ADC_CHANNEL_SEL_MASK, 0); + if (ret) { + dev_err(&indio_dev->dev, + "failed to write IPROC_ANALOG_CONTROL %d\n", ret); + return ret; + } + adc_priv->chan_val = -1; + + /* + * PWR up LDO, ADC, and Band Gap (0 to enable) + * Also enable ADC controller (set high) + */ + ret = regmap_read(adc_priv->regmap, IPROC_REGCTL2, &val); + if (ret) { + dev_err(&indio_dev->dev, + "failed to read IPROC_REGCTL2 %d\n", ret); + return ret; + } + + val &= ~(IPROC_ADC_PWR_LDO | IPROC_ADC_PWR_ADC | IPROC_ADC_PWR_BG); + + ret = regmap_write(adc_priv->regmap, IPROC_REGCTL2, val); + if (ret) { + dev_err(&indio_dev->dev, + "failed to write IPROC_REGCTL2 %d\n", ret); + return ret; + } + + ret = regmap_read(adc_priv->regmap, IPROC_REGCTL2, &val); + if (ret) { + dev_err(&indio_dev->dev, + "failed to read IPROC_REGCTL2 %d\n", ret); + return ret; + } + + val |= IPROC_ADC_CONTROLLER_EN; + ret = regmap_write(adc_priv->regmap, IPROC_REGCTL2, val); + if (ret) { + dev_err(&indio_dev->dev, + "failed to write IPROC_REGCTL2 %d\n", ret); + return ret; + } + + for (channel_id = 0; channel_id < indio_dev->num_channels; + channel_id++) { + ret = regmap_write(adc_priv->regmap, + IPROC_ADC_CHANNEL_INTERRUPT_MASK + + IPROC_ADC_CHANNEL_OFFSET * channel_id, 0); + if (ret) { + dev_err(&indio_dev->dev, + "failed to write ADC_CHANNEL_INTERRUPT_MASK %d\n", + ret); + return ret; + } + + ret = regmap_write(adc_priv->regmap, + IPROC_ADC_CHANNEL_INTERRUPT_STATUS + + IPROC_ADC_CHANNEL_OFFSET * channel_id, 0); + if (ret) { + dev_err(&indio_dev->dev, + "failed to write ADC_CHANNEL_INTERRUPT_STATUS %d\n", + ret); + return ret; + } + } + + return 0; +} + +static void iproc_adc_disable(struct iio_dev *indio_dev) +{ + u32 val; + int ret; + struct iproc_adc_priv *adc_priv = iio_priv(indio_dev); + + ret = regmap_read(adc_priv->regmap, IPROC_REGCTL2, &val); + if (ret) { + dev_err(&indio_dev->dev, + "failed to read IPROC_REGCTL2 %d\n", ret); + return; + } + + val &= ~IPROC_ADC_CONTROLLER_EN; + ret = regmap_write(adc_priv->regmap, IPROC_REGCTL2, val); + if (ret) { + dev_err(&indio_dev->dev, + "failed to write IPROC_REGCTL2 %d\n", ret); + return; + } +} + +static int iproc_adc_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int *val, + int *val2, + long mask) +{ + u16 adc_data; + int err; + + switch (mask) { + case IIO_CHAN_INFO_RAW: + err = iproc_adc_do_read(indio_dev, chan->channel, &adc_data); + if (err < 0) + return err; + *val = adc_data; + return IIO_VAL_INT; + case IIO_CHAN_INFO_SCALE: + switch (chan->type) { + case IIO_VOLTAGE: + *val = 1800; + *val2 = 10; + return IIO_VAL_FRACTIONAL_LOG2; + default: + return -EINVAL; + } + default: + return -EINVAL; + } +} + +static const struct iio_info iproc_adc_iio_info = { + .read_raw = &iproc_adc_read_raw, +}; + +#define IPROC_ADC_CHANNEL(_index, _id) { \ + .type = IIO_VOLTAGE, \ + .indexed = 1, \ + .channel = _index, \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ + .datasheet_name = _id, \ +} + +static const struct iio_chan_spec iproc_adc_iio_channels[] = { + IPROC_ADC_CHANNEL(0, "adc0"), + IPROC_ADC_CHANNEL(1, "adc1"), + IPROC_ADC_CHANNEL(2, "adc2"), + IPROC_ADC_CHANNEL(3, "adc3"), + IPROC_ADC_CHANNEL(4, "adc4"), + IPROC_ADC_CHANNEL(5, "adc5"), + IPROC_ADC_CHANNEL(6, "adc6"), + IPROC_ADC_CHANNEL(7, "adc7"), +}; + +static int iproc_adc_probe(struct platform_device *pdev) +{ + struct iproc_adc_priv *adc_priv; + struct iio_dev *indio_dev = NULL; + int ret; + + indio_dev = devm_iio_device_alloc(&pdev->dev, + sizeof(*adc_priv)); + if (!indio_dev) { + dev_err(&pdev->dev, "failed to allocate iio device\n"); + return -ENOMEM; + } + + adc_priv = iio_priv(indio_dev); + platform_set_drvdata(pdev, indio_dev); + + mutex_init(&adc_priv->mutex); + + init_completion(&adc_priv->completion); + + adc_priv->regmap = syscon_regmap_lookup_by_phandle(pdev->dev.of_node, + "adc-syscon"); + if (IS_ERR(adc_priv->regmap)) { + dev_err(&pdev->dev, "failed to get handle for tsc syscon\n"); + ret = PTR_ERR(adc_priv->regmap); + return ret; + } + + adc_priv->adc_clk = devm_clk_get(&pdev->dev, "tsc_clk"); + if (IS_ERR(adc_priv->adc_clk)) { + dev_err(&pdev->dev, + "failed getting clock tsc_clk\n"); + ret = PTR_ERR(adc_priv->adc_clk); + return ret; + } + + adc_priv->irqno = platform_get_irq(pdev, 0); + if (adc_priv->irqno < 0) + return adc_priv->irqno; + + ret = regmap_update_bits(adc_priv->regmap, IPROC_REGCTL2, + IPROC_ADC_AUXIN_SCAN_ENA, 0); + if (ret) { + dev_err(&pdev->dev, "failed to write IPROC_REGCTL2 %d\n", ret); + return ret; + } + + ret = devm_request_threaded_irq(&pdev->dev, adc_priv->irqno, + iproc_adc_interrupt_handler, + iproc_adc_interrupt_thread, + IRQF_SHARED, "iproc-adc", indio_dev); + if (ret) { + dev_err(&pdev->dev, "request_irq error %d\n", ret); + return ret; + } + + ret = clk_prepare_enable(adc_priv->adc_clk); + if (ret) { + dev_err(&pdev->dev, + "clk_prepare_enable failed %d\n", ret); + return ret; + } + + ret = iproc_adc_enable(indio_dev); + if (ret) { + dev_err(&pdev->dev, "failed to enable adc %d\n", ret); + goto err_adc_enable; + } + + indio_dev->name = "iproc-static-adc"; + indio_dev->info = &iproc_adc_iio_info; + indio_dev->modes = INDIO_DIRECT_MODE; + indio_dev->channels = iproc_adc_iio_channels; + indio_dev->num_channels = ARRAY_SIZE(iproc_adc_iio_channels); + + ret = iio_device_register(indio_dev); + if (ret) { + dev_err(&pdev->dev, "iio_device_register failed:err %d\n", ret); + goto err_clk; + } + + return 0; + +err_clk: + iproc_adc_disable(indio_dev); +err_adc_enable: + clk_disable_unprepare(adc_priv->adc_clk); + + return ret; +} + +static int iproc_adc_remove(struct platform_device *pdev) +{ + struct iio_dev *indio_dev = platform_get_drvdata(pdev); + struct iproc_adc_priv *adc_priv = iio_priv(indio_dev); + + iio_device_unregister(indio_dev); + iproc_adc_disable(indio_dev); + clk_disable_unprepare(adc_priv->adc_clk); + + return 0; +} + +static const struct of_device_id iproc_adc_of_match[] = { + {.compatible = "brcm,iproc-static-adc", }, + { }, +}; +MODULE_DEVICE_TABLE(of, iproc_adc_of_match); + +static struct platform_driver iproc_adc_driver = { + .probe = iproc_adc_probe, + .remove = iproc_adc_remove, + .driver = { + .name = "iproc-static-adc", + .of_match_table = iproc_adc_of_match, + }, +}; +module_platform_driver(iproc_adc_driver); + +MODULE_DESCRIPTION("Broadcom iProc ADC controller driver"); +MODULE_AUTHOR("Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>"); +MODULE_LICENSE("GPL v2"); |