diff options
Diffstat (limited to 'drivers/mmc/host/dw_mmc.h')
-rw-r--r-- | drivers/mmc/host/dw_mmc.h | 589 |
1 files changed, 589 insertions, 0 deletions
diff --git a/drivers/mmc/host/dw_mmc.h b/drivers/mmc/host/dw_mmc.h new file mode 100644 index 0000000000..4ed81f94f7 --- /dev/null +++ b/drivers/mmc/host/dw_mmc.h @@ -0,0 +1,589 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ +/* + * Synopsys DesignWare Multimedia Card Interface driver + * (Based on NXP driver for lpc 31xx) + * + * Copyright (C) 2009 NXP Semiconductors + * Copyright (C) 2009, 2010 Imagination Technologies Ltd. + */ + +#ifndef _DW_MMC_H_ +#define _DW_MMC_H_ + +#include <linux/scatterlist.h> +#include <linux/mmc/core.h> +#include <linux/dmaengine.h> +#include <linux/reset.h> +#include <linux/fault-inject.h> +#include <linux/hrtimer.h> +#include <linux/interrupt.h> + +enum dw_mci_state { + STATE_IDLE = 0, + STATE_SENDING_CMD, + STATE_SENDING_DATA, + STATE_DATA_BUSY, + STATE_SENDING_STOP, + STATE_DATA_ERROR, + STATE_SENDING_CMD11, + STATE_WAITING_CMD11_DONE, +}; + +enum { + EVENT_CMD_COMPLETE = 0, + EVENT_XFER_COMPLETE, + EVENT_DATA_COMPLETE, + EVENT_DATA_ERROR, +}; + +enum dw_mci_cookie { + COOKIE_UNMAPPED, + COOKIE_PRE_MAPPED, /* mapped by pre_req() of dwmmc */ + COOKIE_MAPPED, /* mapped by prepare_data() of dwmmc */ +}; + +struct mmc_data; + +enum { + TRANS_MODE_PIO = 0, + TRANS_MODE_IDMAC, + TRANS_MODE_EDMAC +}; + +struct dw_mci_dma_slave { + struct dma_chan *ch; + enum dma_transfer_direction direction; +}; + +/** + * struct dw_mci - MMC controller state shared between all slots + * @lock: Spinlock protecting the queue and associated data. + * @irq_lock: Spinlock protecting the INTMASK setting. + * @regs: Pointer to MMIO registers. + * @fifo_reg: Pointer to MMIO registers for data FIFO + * @sg: Scatterlist entry currently being processed by PIO code, if any. + * @sg_miter: PIO mapping scatterlist iterator. + * @mrq: The request currently being processed on @slot, + * or NULL if the controller is idle. + * @cmd: The command currently being sent to the card, or NULL. + * @data: The data currently being transferred, or NULL if no data + * transfer is in progress. + * @stop_abort: The command currently prepared for stoping transfer. + * @prev_blksz: The former transfer blksz record. + * @timing: Record of current ios timing. + * @use_dma: Which DMA channel is in use for the current transfer, zero + * denotes PIO mode. + * @using_dma: Whether DMA is in use for the current transfer. + * @dma_64bit_address: Whether DMA supports 64-bit address mode or not. + * @sg_dma: Bus address of DMA buffer. + * @sg_cpu: Virtual address of DMA buffer. + * @dma_ops: Pointer to platform-specific DMA callbacks. + * @cmd_status: Snapshot of SR taken upon completion of the current + * @ring_size: Buffer size for idma descriptors. + * command. Only valid when EVENT_CMD_COMPLETE is pending. + * @dms: structure of slave-dma private data. + * @phy_regs: physical address of controller's register map + * @data_status: Snapshot of SR taken upon completion of the current + * data transfer. Only valid when EVENT_DATA_COMPLETE or + * EVENT_DATA_ERROR is pending. + * @stop_cmdr: Value to be loaded into CMDR when the stop command is + * to be sent. + * @dir_status: Direction of current transfer. + * @tasklet: Tasklet running the request state machine. + * @pending_events: Bitmask of events flagged by the interrupt handler + * to be processed by the tasklet. + * @completed_events: Bitmask of events which the state machine has + * processed. + * @state: Tasklet state. + * @queue: List of slots waiting for access to the controller. + * @bus_hz: The rate of @mck in Hz. This forms the basis for MMC bus + * rate and timeout calculations. + * @current_speed: Configured rate of the controller. + * @minimum_speed: Stored minimum rate of the controller. + * @fifoth_val: The value of FIFOTH register. + * @verid: Denote Version ID. + * @dev: Device associated with the MMC controller. + * @pdata: Platform data associated with the MMC controller. + * @drv_data: Driver specific data for identified variant of the controller + * @priv: Implementation defined private data. + * @biu_clk: Pointer to bus interface unit clock instance. + * @ciu_clk: Pointer to card interface unit clock instance. + * @slot: Slots sharing this MMC controller. + * @fifo_depth: depth of FIFO. + * @data_addr_override: override fifo reg offset with this value. + * @wm_aligned: force fifo watermark equal with data length in PIO mode. + * Set as true if alignment is needed. + * @data_shift: log2 of FIFO item size. + * @part_buf_start: Start index in part_buf. + * @part_buf_count: Bytes of partial data in part_buf. + * @part_buf: Simple buffer for partial fifo reads/writes. + * @push_data: Pointer to FIFO push function. + * @pull_data: Pointer to FIFO pull function. + * @quirks: Set of quirks that apply to specific versions of the IP. + * @vqmmc_enabled: Status of vqmmc, should be true or false. + * @irq_flags: The flags to be passed to request_irq. + * @irq: The irq value to be passed to request_irq. + * @sdio_id0: Number of slot0 in the SDIO interrupt registers. + * @cmd11_timer: Timer for SD3.0 voltage switch over scheme. + * @cto_timer: Timer for broken command transfer over scheme. + * @dto_timer: Timer for broken data transfer over scheme. + * + * Locking + * ======= + * + * @lock is a softirq-safe spinlock protecting @queue as well as + * @slot, @mrq and @state. These must always be updated + * at the same time while holding @lock. + * The @mrq field of struct dw_mci_slot is also protected by @lock, + * and must always be written at the same time as the slot is added to + * @queue. + * + * @irq_lock is an irq-safe spinlock protecting the INTMASK register + * to allow the interrupt handler to modify it directly. Held for only long + * enough to read-modify-write INTMASK and no other locks are grabbed when + * holding this one. + * + * @pending_events and @completed_events are accessed using atomic bit + * operations, so they don't need any locking. + * + * None of the fields touched by the interrupt handler need any + * locking. However, ordering is important: Before EVENT_DATA_ERROR or + * EVENT_DATA_COMPLETE is set in @pending_events, all data-related + * interrupts must be disabled and @data_status updated with a + * snapshot of SR. Similarly, before EVENT_CMD_COMPLETE is set, the + * CMDRDY interrupt must be disabled and @cmd_status updated with a + * snapshot of SR, and before EVENT_XFER_COMPLETE can be set, the + * bytes_xfered field of @data must be written. This is ensured by + * using barriers. + */ +struct dw_mci { + spinlock_t lock; + spinlock_t irq_lock; + void __iomem *regs; + void __iomem *fifo_reg; + u32 data_addr_override; + bool wm_aligned; + + struct scatterlist *sg; + struct sg_mapping_iter sg_miter; + + struct mmc_request *mrq; + struct mmc_command *cmd; + struct mmc_data *data; + struct mmc_command stop_abort; + unsigned int prev_blksz; + unsigned char timing; + + /* DMA interface members*/ + int use_dma; + int using_dma; + int dma_64bit_address; + + dma_addr_t sg_dma; + void *sg_cpu; + const struct dw_mci_dma_ops *dma_ops; + /* For idmac */ + unsigned int ring_size; + + /* For edmac */ + struct dw_mci_dma_slave *dms; + /* Registers's physical base address */ + resource_size_t phy_regs; + + u32 cmd_status; + u32 data_status; + u32 stop_cmdr; + u32 dir_status; + struct tasklet_struct tasklet; + unsigned long pending_events; + unsigned long completed_events; + enum dw_mci_state state; + struct list_head queue; + + u32 bus_hz; + u32 current_speed; + u32 minimum_speed; + u32 fifoth_val; + u16 verid; + struct device *dev; + struct dw_mci_board *pdata; + const struct dw_mci_drv_data *drv_data; + void *priv; + struct clk *biu_clk; + struct clk *ciu_clk; + struct dw_mci_slot *slot; + + /* FIFO push and pull */ + int fifo_depth; + int data_shift; + u8 part_buf_start; + u8 part_buf_count; + union { + u16 part_buf16; + u32 part_buf32; + u64 part_buf; + }; + void (*push_data)(struct dw_mci *host, void *buf, int cnt); + void (*pull_data)(struct dw_mci *host, void *buf, int cnt); + + u32 quirks; + bool vqmmc_enabled; + unsigned long irq_flags; /* IRQ flags */ + int irq; + + int sdio_id0; + + struct timer_list cmd11_timer; + struct timer_list cto_timer; + struct timer_list dto_timer; + +#ifdef CONFIG_FAULT_INJECTION + struct fault_attr fail_data_crc; + struct hrtimer fault_timer; +#endif +}; + +/* DMA ops for Internal/External DMAC interface */ +struct dw_mci_dma_ops { + /* DMA Ops */ + int (*init)(struct dw_mci *host); + int (*start)(struct dw_mci *host, unsigned int sg_len); + void (*complete)(void *host); + void (*stop)(struct dw_mci *host); + void (*cleanup)(struct dw_mci *host); + void (*exit)(struct dw_mci *host); +}; + +struct dma_pdata; + +/* Board platform data */ +struct dw_mci_board { + unsigned int bus_hz; /* Clock speed at the cclk_in pad */ + + u32 caps; /* Capabilities */ + u32 caps2; /* More capabilities */ + u32 pm_caps; /* PM capabilities */ + /* + * Override fifo depth. If 0, autodetect it from the FIFOTH register, + * but note that this may not be reliable after a bootloader has used + * it. + */ + unsigned int fifo_depth; + + /* delay in mS before detecting cards after interrupt */ + u32 detect_delay_ms; + + struct reset_control *rstc; + struct dw_mci_dma_ops *dma_ops; + struct dma_pdata *data; +}; + +/* Support for longer data read timeout */ +#define DW_MMC_QUIRK_EXTENDED_TMOUT BIT(0) + +#define DW_MMC_240A 0x240a +#define DW_MMC_280A 0x280a + +#define SDMMC_CTRL 0x000 +#define SDMMC_PWREN 0x004 +#define SDMMC_CLKDIV 0x008 +#define SDMMC_CLKSRC 0x00c +#define SDMMC_CLKENA 0x010 +#define SDMMC_TMOUT 0x014 +#define SDMMC_CTYPE 0x018 +#define SDMMC_BLKSIZ 0x01c +#define SDMMC_BYTCNT 0x020 +#define SDMMC_INTMASK 0x024 +#define SDMMC_CMDARG 0x028 +#define SDMMC_CMD 0x02c +#define SDMMC_RESP0 0x030 +#define SDMMC_RESP1 0x034 +#define SDMMC_RESP2 0x038 +#define SDMMC_RESP3 0x03c +#define SDMMC_MINTSTS 0x040 +#define SDMMC_RINTSTS 0x044 +#define SDMMC_STATUS 0x048 +#define SDMMC_FIFOTH 0x04c +#define SDMMC_CDETECT 0x050 +#define SDMMC_WRTPRT 0x054 +#define SDMMC_GPIO 0x058 +#define SDMMC_TCBCNT 0x05c +#define SDMMC_TBBCNT 0x060 +#define SDMMC_DEBNCE 0x064 +#define SDMMC_USRID 0x068 +#define SDMMC_VERID 0x06c +#define SDMMC_HCON 0x070 +#define SDMMC_UHS_REG 0x074 +#define SDMMC_RST_N 0x078 +#define SDMMC_BMOD 0x080 +#define SDMMC_PLDMND 0x084 +#define SDMMC_DBADDR 0x088 +#define SDMMC_IDSTS 0x08c +#define SDMMC_IDINTEN 0x090 +#define SDMMC_DSCADDR 0x094 +#define SDMMC_BUFADDR 0x098 +#define SDMMC_CDTHRCTL 0x100 +#define SDMMC_UHS_REG_EXT 0x108 +#define SDMMC_DDR_REG 0x10c +#define SDMMC_ENABLE_SHIFT 0x110 +#define SDMMC_DATA(x) (x) +/* + * Registers to support idmac 64-bit address mode + */ +#define SDMMC_DBADDRL 0x088 +#define SDMMC_DBADDRU 0x08c +#define SDMMC_IDSTS64 0x090 +#define SDMMC_IDINTEN64 0x094 +#define SDMMC_DSCADDRL 0x098 +#define SDMMC_DSCADDRU 0x09c +#define SDMMC_BUFADDRL 0x0A0 +#define SDMMC_BUFADDRU 0x0A4 + +/* + * Data offset is difference according to Version + * Lower than 2.40a : data register offest is 0x100 + */ +#define DATA_OFFSET 0x100 +#define DATA_240A_OFFSET 0x200 + +/* shift bit field */ +#define _SBF(f, v) ((v) << (f)) + +/* Control register defines */ +#define SDMMC_CTRL_USE_IDMAC BIT(25) +#define SDMMC_CTRL_CEATA_INT_EN BIT(11) +#define SDMMC_CTRL_SEND_AS_CCSD BIT(10) +#define SDMMC_CTRL_SEND_CCSD BIT(9) +#define SDMMC_CTRL_ABRT_READ_DATA BIT(8) +#define SDMMC_CTRL_SEND_IRQ_RESP BIT(7) +#define SDMMC_CTRL_READ_WAIT BIT(6) +#define SDMMC_CTRL_DMA_ENABLE BIT(5) +#define SDMMC_CTRL_INT_ENABLE BIT(4) +#define SDMMC_CTRL_DMA_RESET BIT(2) +#define SDMMC_CTRL_FIFO_RESET BIT(1) +#define SDMMC_CTRL_RESET BIT(0) +/* Clock Enable register defines */ +#define SDMMC_CLKEN_LOW_PWR BIT(16) +#define SDMMC_CLKEN_ENABLE BIT(0) +/* time-out register defines */ +#define SDMMC_TMOUT_DATA(n) _SBF(8, (n)) +#define SDMMC_TMOUT_DATA_MSK 0xFFFFFF00 +#define SDMMC_TMOUT_RESP(n) ((n) & 0xFF) +#define SDMMC_TMOUT_RESP_MSK 0xFF +/* card-type register defines */ +#define SDMMC_CTYPE_8BIT BIT(16) +#define SDMMC_CTYPE_4BIT BIT(0) +#define SDMMC_CTYPE_1BIT 0 +/* Interrupt status & mask register defines */ +#define SDMMC_INT_SDIO(n) BIT(16 + (n)) +#define SDMMC_INT_EBE BIT(15) +#define SDMMC_INT_ACD BIT(14) +#define SDMMC_INT_SBE BIT(13) +#define SDMMC_INT_HLE BIT(12) +#define SDMMC_INT_FRUN BIT(11) +#define SDMMC_INT_HTO BIT(10) +#define SDMMC_INT_VOLT_SWITCH BIT(10) /* overloads bit 10! */ +#define SDMMC_INT_DRTO BIT(9) +#define SDMMC_INT_RTO BIT(8) +#define SDMMC_INT_DCRC BIT(7) +#define SDMMC_INT_RCRC BIT(6) +#define SDMMC_INT_RXDR BIT(5) +#define SDMMC_INT_TXDR BIT(4) +#define SDMMC_INT_DATA_OVER BIT(3) +#define SDMMC_INT_CMD_DONE BIT(2) +#define SDMMC_INT_RESP_ERR BIT(1) +#define SDMMC_INT_CD BIT(0) +#define SDMMC_INT_ERROR 0xbfc2 +/* Command register defines */ +#define SDMMC_CMD_START BIT(31) +#define SDMMC_CMD_USE_HOLD_REG BIT(29) +#define SDMMC_CMD_VOLT_SWITCH BIT(28) +#define SDMMC_CMD_CCS_EXP BIT(23) +#define SDMMC_CMD_CEATA_RD BIT(22) +#define SDMMC_CMD_UPD_CLK BIT(21) +#define SDMMC_CMD_INIT BIT(15) +#define SDMMC_CMD_STOP BIT(14) +#define SDMMC_CMD_PRV_DAT_WAIT BIT(13) +#define SDMMC_CMD_SEND_STOP BIT(12) +#define SDMMC_CMD_STRM_MODE BIT(11) +#define SDMMC_CMD_DAT_WR BIT(10) +#define SDMMC_CMD_DAT_EXP BIT(9) +#define SDMMC_CMD_RESP_CRC BIT(8) +#define SDMMC_CMD_RESP_LONG BIT(7) +#define SDMMC_CMD_RESP_EXP BIT(6) +#define SDMMC_CMD_INDX(n) ((n) & 0x1F) +/* Status register defines */ +#define SDMMC_GET_FCNT(x) (((x)>>17) & 0x1FFF) +#define SDMMC_STATUS_DMA_REQ BIT(31) +#define SDMMC_STATUS_BUSY BIT(9) +/* FIFOTH register defines */ +#define SDMMC_SET_FIFOTH(m, r, t) (((m) & 0x7) << 28 | \ + ((r) & 0xFFF) << 16 | \ + ((t) & 0xFFF)) +/* HCON register defines */ +#define DMA_INTERFACE_IDMA (0x0) +#define DMA_INTERFACE_DWDMA (0x1) +#define DMA_INTERFACE_GDMA (0x2) +#define DMA_INTERFACE_NODMA (0x3) +#define SDMMC_GET_TRANS_MODE(x) (((x)>>16) & 0x3) +#define SDMMC_GET_SLOT_NUM(x) ((((x)>>1) & 0x1F) + 1) +#define SDMMC_GET_HDATA_WIDTH(x) (((x)>>7) & 0x7) +#define SDMMC_GET_ADDR_CONFIG(x) (((x)>>27) & 0x1) +/* Internal DMAC interrupt defines */ +#define SDMMC_IDMAC_INT_AI BIT(9) +#define SDMMC_IDMAC_INT_NI BIT(8) +#define SDMMC_IDMAC_INT_CES BIT(5) +#define SDMMC_IDMAC_INT_DU BIT(4) +#define SDMMC_IDMAC_INT_FBE BIT(2) +#define SDMMC_IDMAC_INT_RI BIT(1) +#define SDMMC_IDMAC_INT_TI BIT(0) +/* Internal DMAC bus mode bits */ +#define SDMMC_IDMAC_ENABLE BIT(7) +#define SDMMC_IDMAC_FB BIT(1) +#define SDMMC_IDMAC_SWRESET BIT(0) +/* H/W reset */ +#define SDMMC_RST_HWACTIVE 0x1 +/* Version ID register define */ +#define SDMMC_GET_VERID(x) ((x) & 0xFFFF) +/* Card read threshold */ +#define SDMMC_SET_THLD(v, x) (((v) & 0xFFF) << 16 | (x)) +#define SDMMC_CARD_WR_THR_EN BIT(2) +#define SDMMC_CARD_RD_THR_EN BIT(0) +/* UHS-1 register defines */ +#define SDMMC_UHS_DDR BIT(16) +#define SDMMC_UHS_18V BIT(0) +/* DDR register defines */ +#define SDMMC_DDR_HS400 BIT(31) +/* Enable shift register defines */ +#define SDMMC_ENABLE_PHASE BIT(0) +/* All ctrl reset bits */ +#define SDMMC_CTRL_ALL_RESET_FLAGS \ + (SDMMC_CTRL_RESET | SDMMC_CTRL_FIFO_RESET | SDMMC_CTRL_DMA_RESET) + +/* FIFO register access macros. These should not change the data endian-ness + * as they are written to memory to be dealt with by the upper layers + */ +#define mci_fifo_readw(__reg) __raw_readw(__reg) +#define mci_fifo_readl(__reg) __raw_readl(__reg) +#define mci_fifo_readq(__reg) __raw_readq(__reg) + +#define mci_fifo_writew(__value, __reg) __raw_writew(__reg, __value) +#define mci_fifo_writel(__value, __reg) __raw_writel(__reg, __value) +#define mci_fifo_writeq(__value, __reg) __raw_writeq(__reg, __value) + +/* Register access macros */ +#define mci_readl(dev, reg) \ + readl_relaxed((dev)->regs + SDMMC_##reg) +#define mci_writel(dev, reg, value) \ + writel_relaxed((value), (dev)->regs + SDMMC_##reg) + +/* 16-bit FIFO access macros */ +#define mci_readw(dev, reg) \ + readw_relaxed((dev)->regs + SDMMC_##reg) +#define mci_writew(dev, reg, value) \ + writew_relaxed((value), (dev)->regs + SDMMC_##reg) + +/* 64-bit FIFO access macros */ +#ifdef readq +#define mci_readq(dev, reg) \ + readq_relaxed((dev)->regs + SDMMC_##reg) +#define mci_writeq(dev, reg, value) \ + writeq_relaxed((value), (dev)->regs + SDMMC_##reg) +#else +/* + * Dummy readq implementation for architectures that don't define it. + * + * We would assume that none of these architectures would configure + * the IP block with a 64bit FIFO width, so this code will never be + * executed on those machines. Defining these macros here keeps the + * rest of the code free from ifdefs. + */ +#define mci_readq(dev, reg) \ + (*(volatile u64 __force *)((dev)->regs + SDMMC_##reg)) +#define mci_writeq(dev, reg, value) \ + (*(volatile u64 __force *)((dev)->regs + SDMMC_##reg) = (value)) + +#define __raw_writeq(__value, __reg) \ + (*(volatile u64 __force *)(__reg) = (__value)) +#define __raw_readq(__reg) (*(volatile u64 __force *)(__reg)) +#endif + +extern int dw_mci_probe(struct dw_mci *host); +extern void dw_mci_remove(struct dw_mci *host); +#ifdef CONFIG_PM +extern int dw_mci_runtime_suspend(struct device *device); +extern int dw_mci_runtime_resume(struct device *device); +#endif + +/** + * struct dw_mci_slot - MMC slot state + * @mmc: The mmc_host representing this slot. + * @host: The MMC controller this slot is using. + * @ctype: Card type for this slot. + * @mrq: mmc_request currently being processed or waiting to be + * processed, or NULL when the slot is idle. + * @queue_node: List node for placing this node in the @queue list of + * &struct dw_mci. + * @clock: Clock rate configured by set_ios(). Protected by host->lock. + * @__clk_old: The last clock value that was requested from core. + * Keeping track of this helps us to avoid spamming the console. + * @flags: Random state bits associated with the slot. + * @id: Number of this slot. + * @sdio_id: Number of this slot in the SDIO interrupt registers. + */ +struct dw_mci_slot { + struct mmc_host *mmc; + struct dw_mci *host; + + u32 ctype; + + struct mmc_request *mrq; + struct list_head queue_node; + + unsigned int clock; + unsigned int __clk_old; + + unsigned long flags; +#define DW_MMC_CARD_PRESENT 0 +#define DW_MMC_CARD_NEED_INIT 1 +#define DW_MMC_CARD_NO_LOW_PWR 2 +#define DW_MMC_CARD_NO_USE_HOLD 3 +#define DW_MMC_CARD_NEEDS_POLL 4 + int id; + int sdio_id; +}; + +/** + * dw_mci driver data - dw-mshc implementation specific driver data. + * @caps: mmc subsystem specified capabilities of the controller(s). + * @num_caps: number of capabilities specified by @caps. + * @common_caps: mmc subsystem specified capabilities applicable to all of + * the controllers + * @init: early implementation specific initialization. + * @set_ios: handle bus specific extensions. + * @parse_dt: parse implementation specific device tree properties. + * @execute_tuning: implementation specific tuning procedure. + * @set_data_timeout: implementation specific timeout. + * @get_drto_clks: implementation specific cycle count for data read timeout. + * + * Provide controller implementation specific extensions. The usage of this + * data structure is fully optional and usage of each member in this structure + * is optional as well. + */ +struct dw_mci_drv_data { + unsigned long *caps; + u32 num_caps; + u32 common_caps; + int (*init)(struct dw_mci *host); + void (*set_ios)(struct dw_mci *host, struct mmc_ios *ios); + int (*parse_dt)(struct dw_mci *host); + int (*execute_tuning)(struct dw_mci_slot *slot, u32 opcode); + int (*prepare_hs400_tuning)(struct dw_mci *host, + struct mmc_ios *ios); + int (*switch_voltage)(struct mmc_host *mmc, + struct mmc_ios *ios); + void (*set_data_timeout)(struct dw_mci *host, + unsigned int timeout_ns); + u32 (*get_drto_clks)(struct dw_mci *host); +}; +#endif /* _DW_MMC_H_ */ |