diff options
Diffstat (limited to 'drivers/mmc/host/sdhci-pxav2.c')
| -rw-r--r-- | drivers/mmc/host/sdhci-pxav2.c | 362 |
1 files changed, 362 insertions, 0 deletions
diff --git a/drivers/mmc/host/sdhci-pxav2.c b/drivers/mmc/host/sdhci-pxav2.c new file mode 100644 index 0000000000..b75cbea88b --- /dev/null +++ b/drivers/mmc/host/sdhci-pxav2.c @@ -0,0 +1,362 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2010 Marvell International Ltd. + * Zhangfei Gao <zhangfei.gao@marvell.com> + * Kevin Wang <dwang4@marvell.com> + * Jun Nie <njun@marvell.com> + * Qiming Wu <wuqm@marvell.com> + * Philip Rakity <prakity@marvell.com> + */ + +#include <linux/err.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/clk.h> +#include <linux/module.h> +#include <linux/io.h> +#include <linux/mmc/card.h> +#include <linux/mmc/host.h> +#include <linux/platform_data/pxa_sdhci.h> +#include <linux/slab.h> +#include <linux/of.h> +#include <linux/mmc/sdio.h> +#include <linux/mmc/mmc.h> +#include <linux/pinctrl/consumer.h> + +#include "sdhci.h" +#include "sdhci-pltfm.h" + +#define SD_FIFO_PARAM 0xe0 +#define DIS_PAD_SD_CLK_GATE 0x0400 /* Turn on/off Dynamic SD Clock Gating */ +#define CLK_GATE_ON 0x0200 /* Disable/enable Clock Gate */ +#define CLK_GATE_CTL 0x0100 /* Clock Gate Control */ +#define CLK_GATE_SETTING_BITS (DIS_PAD_SD_CLK_GATE | \ + CLK_GATE_ON | CLK_GATE_CTL) + +#define SD_CLOCK_BURST_SIZE_SETUP 0xe6 +#define SDCLK_SEL_SHIFT 8 +#define SDCLK_SEL_MASK 0x3 +#define SDCLK_DELAY_SHIFT 10 +#define SDCLK_DELAY_MASK 0x3c + +#define SD_CE_ATA_2 0xea +#define MMC_CARD 0x1000 +#define MMC_WIDTH 0x0100 + +struct sdhci_pxav2_host { + struct mmc_request *sdio_mrq; + struct pinctrl *pinctrl; + struct pinctrl_state *pins_default; + struct pinctrl_state *pins_cmd_gpio; +}; + +static void pxav2_reset(struct sdhci_host *host, u8 mask) +{ + struct platform_device *pdev = to_platform_device(mmc_dev(host->mmc)); + struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data; + + sdhci_reset(host, mask); + + if (mask == SDHCI_RESET_ALL) { + u16 tmp = 0; + + /* + * tune timing of read data/command when crc error happen + * no performance impact + */ + if (pdata && pdata->clk_delay_sel == 1) { + tmp = readw(host->ioaddr + SD_CLOCK_BURST_SIZE_SETUP); + + tmp &= ~(SDCLK_DELAY_MASK << SDCLK_DELAY_SHIFT); + tmp |= (pdata->clk_delay_cycles & SDCLK_DELAY_MASK) + << SDCLK_DELAY_SHIFT; + tmp &= ~(SDCLK_SEL_MASK << SDCLK_SEL_SHIFT); + tmp |= (1 & SDCLK_SEL_MASK) << SDCLK_SEL_SHIFT; + + writew(tmp, host->ioaddr + SD_CLOCK_BURST_SIZE_SETUP); + } + + if (pdata && (pdata->flags & PXA_FLAG_ENABLE_CLOCK_GATING)) { + tmp = readw(host->ioaddr + SD_FIFO_PARAM); + tmp &= ~CLK_GATE_SETTING_BITS; + writew(tmp, host->ioaddr + SD_FIFO_PARAM); + } else { + tmp = readw(host->ioaddr + SD_FIFO_PARAM); + tmp &= ~CLK_GATE_SETTING_BITS; + tmp |= CLK_GATE_SETTING_BITS; + writew(tmp, host->ioaddr + SD_FIFO_PARAM); + } + } +} + +static u16 pxav1_readw(struct sdhci_host *host, int reg) +{ + /* Workaround for data abort exception on SDH2 and SDH4 on PXA168 */ + if (reg == SDHCI_HOST_VERSION) + return readl(host->ioaddr + SDHCI_HOST_VERSION - 2) >> 16; + + return readw(host->ioaddr + reg); +} + +static u32 pxav1_irq(struct sdhci_host *host, u32 intmask) +{ + struct sdhci_pxav2_host *pxav2_host = sdhci_pltfm_priv(sdhci_priv(host)); + struct mmc_request *sdio_mrq; + + if (pxav2_host->sdio_mrq && (intmask & SDHCI_INT_CMD_MASK)) { + /* The dummy CMD0 for the SDIO workaround just completed */ + sdhci_writel(host, intmask & SDHCI_INT_CMD_MASK, SDHCI_INT_STATUS); + intmask &= ~SDHCI_INT_CMD_MASK; + + /* Restore MMC function to CMD pin */ + if (pxav2_host->pinctrl && pxav2_host->pins_default) + pinctrl_select_state(pxav2_host->pinctrl, pxav2_host->pins_default); + + sdio_mrq = pxav2_host->sdio_mrq; + pxav2_host->sdio_mrq = NULL; + mmc_request_done(host->mmc, sdio_mrq); + } + + return intmask; +} + +static void pxav1_request_done(struct sdhci_host *host, struct mmc_request *mrq) +{ + u16 tmp; + struct sdhci_pxav2_host *pxav2_host; + + /* If this is an SDIO command, perform errata workaround for silicon bug */ + if (mrq->cmd && !mrq->cmd->error && + (mrq->cmd->opcode == SD_IO_RW_DIRECT || + mrq->cmd->opcode == SD_IO_RW_EXTENDED)) { + /* Reset data port */ + tmp = readw(host->ioaddr + SDHCI_TIMEOUT_CONTROL); + tmp |= 0x400; + writew(tmp, host->ioaddr + SDHCI_TIMEOUT_CONTROL); + + /* Clock is now stopped, so restart it by sending a dummy CMD0 */ + pxav2_host = sdhci_pltfm_priv(sdhci_priv(host)); + pxav2_host->sdio_mrq = mrq; + + /* Set CMD as high output rather than MMC function while we do CMD0 */ + if (pxav2_host->pinctrl && pxav2_host->pins_cmd_gpio) + pinctrl_select_state(pxav2_host->pinctrl, pxav2_host->pins_cmd_gpio); + + sdhci_writel(host, 0, SDHCI_ARGUMENT); + sdhci_writew(host, 0, SDHCI_TRANSFER_MODE); + sdhci_writew(host, SDHCI_MAKE_CMD(MMC_GO_IDLE_STATE, SDHCI_CMD_RESP_NONE), + SDHCI_COMMAND); + + /* Don't finish this request until the dummy CMD0 finishes */ + return; + } + + mmc_request_done(host->mmc, mrq); +} + +static void pxav2_mmc_set_bus_width(struct sdhci_host *host, int width) +{ + u8 ctrl; + u16 tmp; + + ctrl = readb(host->ioaddr + SDHCI_HOST_CONTROL); + tmp = readw(host->ioaddr + SD_CE_ATA_2); + if (width == MMC_BUS_WIDTH_8) { + ctrl &= ~SDHCI_CTRL_4BITBUS; + tmp |= MMC_CARD | MMC_WIDTH; + } else { + tmp &= ~(MMC_CARD | MMC_WIDTH); + if (width == MMC_BUS_WIDTH_4) + ctrl |= SDHCI_CTRL_4BITBUS; + else + ctrl &= ~SDHCI_CTRL_4BITBUS; + } + writew(tmp, host->ioaddr + SD_CE_ATA_2); + writeb(ctrl, host->ioaddr + SDHCI_HOST_CONTROL); +} + +struct sdhci_pxa_variant { + const struct sdhci_ops *ops; + unsigned int extra_quirks; +}; + +static const struct sdhci_ops pxav1_sdhci_ops = { + .read_w = pxav1_readw, + .set_clock = sdhci_set_clock, + .irq = pxav1_irq, + .get_max_clock = sdhci_pltfm_clk_get_max_clock, + .set_bus_width = pxav2_mmc_set_bus_width, + .reset = pxav2_reset, + .set_uhs_signaling = sdhci_set_uhs_signaling, + .request_done = pxav1_request_done, +}; + +static const struct sdhci_pxa_variant __maybe_unused pxav1_variant = { + .ops = &pxav1_sdhci_ops, + .extra_quirks = SDHCI_QUIRK_NO_BUSY_IRQ | SDHCI_QUIRK_32BIT_DMA_SIZE, +}; + +static const struct sdhci_ops pxav2_sdhci_ops = { + .set_clock = sdhci_set_clock, + .get_max_clock = sdhci_pltfm_clk_get_max_clock, + .set_bus_width = pxav2_mmc_set_bus_width, + .reset = pxav2_reset, + .set_uhs_signaling = sdhci_set_uhs_signaling, +}; + +static const struct sdhci_pxa_variant pxav2_variant = { + .ops = &pxav2_sdhci_ops, +}; + +#ifdef CONFIG_OF +static const struct of_device_id sdhci_pxav2_of_match[] = { + { .compatible = "mrvl,pxav1-mmc", .data = &pxav1_variant, }, + { .compatible = "mrvl,pxav2-mmc", .data = &pxav2_variant, }, + {}, +}; +MODULE_DEVICE_TABLE(of, sdhci_pxav2_of_match); + +static struct sdhci_pxa_platdata *pxav2_get_mmc_pdata(struct device *dev) +{ + struct sdhci_pxa_platdata *pdata; + struct device_node *np = dev->of_node; + u32 bus_width; + u32 clk_delay_cycles; + + pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); + if (!pdata) + return NULL; + + if (of_property_read_bool(np, "non-removable")) + pdata->flags |= PXA_FLAG_CARD_PERMANENT; + + of_property_read_u32(np, "bus-width", &bus_width); + if (bus_width == 8) + pdata->flags |= PXA_FLAG_SD_8_BIT_CAPABLE_SLOT; + + of_property_read_u32(np, "mrvl,clk-delay-cycles", &clk_delay_cycles); + if (clk_delay_cycles > 0) { + pdata->clk_delay_sel = 1; + pdata->clk_delay_cycles = clk_delay_cycles; + } + + return pdata; +} +#else +static inline struct sdhci_pxa_platdata *pxav2_get_mmc_pdata(struct device *dev) +{ + return NULL; +} +#endif + +static int sdhci_pxav2_probe(struct platform_device *pdev) +{ + struct sdhci_pltfm_host *pltfm_host; + struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data; + struct sdhci_pxav2_host *pxav2_host; + struct device *dev = &pdev->dev; + struct sdhci_host *host = NULL; + const struct sdhci_pxa_variant *variant; + + int ret; + struct clk *clk, *clk_core; + + host = sdhci_pltfm_init(pdev, NULL, sizeof(*pxav2_host)); + if (IS_ERR(host)) + return PTR_ERR(host); + + pltfm_host = sdhci_priv(host); + pxav2_host = sdhci_pltfm_priv(pltfm_host); + + clk = devm_clk_get_optional_enabled(dev, "io"); + if (!clk) + clk = devm_clk_get_enabled(dev, NULL); + if (IS_ERR(clk)) { + ret = PTR_ERR(clk); + dev_err_probe(dev, ret, "failed to get io clock\n"); + goto free; + } + pltfm_host->clk = clk; + + clk_core = devm_clk_get_optional_enabled(dev, "core"); + if (IS_ERR(clk_core)) { + ret = PTR_ERR(clk_core); + dev_err_probe(dev, ret, "failed to enable core clock\n"); + goto free; + } + + host->quirks = SDHCI_QUIRK_BROKEN_ADMA + | SDHCI_QUIRK_BROKEN_TIMEOUT_VAL + | SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN; + + variant = of_device_get_match_data(dev); + if (variant) + pdata = pxav2_get_mmc_pdata(dev); + else + variant = &pxav2_variant; + + if (pdata) { + if (pdata->flags & PXA_FLAG_CARD_PERMANENT) { + /* on-chip device */ + host->quirks |= SDHCI_QUIRK_BROKEN_CARD_DETECTION; + host->mmc->caps |= MMC_CAP_NONREMOVABLE; + } + + /* If slot design supports 8 bit data, indicate this to MMC. */ + if (pdata->flags & PXA_FLAG_SD_8_BIT_CAPABLE_SLOT) + host->mmc->caps |= MMC_CAP_8_BIT_DATA; + + if (pdata->quirks) + host->quirks |= pdata->quirks; + if (pdata->host_caps) + host->mmc->caps |= pdata->host_caps; + if (pdata->pm_caps) + host->mmc->pm_caps |= pdata->pm_caps; + } + + host->quirks |= variant->extra_quirks; + host->ops = variant->ops; + + /* Set up optional pinctrl for PXA168 SDIO IRQ fix */ + pxav2_host->pinctrl = devm_pinctrl_get(dev); + if (!IS_ERR(pxav2_host->pinctrl)) { + pxav2_host->pins_cmd_gpio = pinctrl_lookup_state(pxav2_host->pinctrl, + "state_cmd_gpio"); + if (IS_ERR(pxav2_host->pins_cmd_gpio)) + pxav2_host->pins_cmd_gpio = NULL; + pxav2_host->pins_default = pinctrl_lookup_state(pxav2_host->pinctrl, + "default"); + if (IS_ERR(pxav2_host->pins_default)) + pxav2_host->pins_default = NULL; + } else { + pxav2_host->pinctrl = NULL; + } + + ret = sdhci_add_host(host); + if (ret) + goto free; + + return 0; + +free: + sdhci_pltfm_free(pdev); + return ret; +} + +static struct platform_driver sdhci_pxav2_driver = { + .driver = { + .name = "sdhci-pxav2", + .probe_type = PROBE_PREFER_ASYNCHRONOUS, + .of_match_table = of_match_ptr(sdhci_pxav2_of_match), + .pm = &sdhci_pltfm_pmops, + }, + .probe = sdhci_pxav2_probe, + .remove_new = sdhci_pltfm_remove, +}; + +module_platform_driver(sdhci_pxav2_driver); + +MODULE_DESCRIPTION("SDHCI driver for pxav2"); +MODULE_AUTHOR("Marvell International Ltd."); +MODULE_LICENSE("GPL v2"); + |