diff options
Diffstat (limited to 'drivers/mmc/host/toshsd.c')
-rw-r--r-- | drivers/mmc/host/toshsd.c | 709 |
1 files changed, 709 insertions, 0 deletions
diff --git a/drivers/mmc/host/toshsd.c b/drivers/mmc/host/toshsd.c new file mode 100644 index 0000000000..497791ffad --- /dev/null +++ b/drivers/mmc/host/toshsd.c @@ -0,0 +1,709 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Toshiba PCI Secure Digital Host Controller Interface driver + * + * Copyright (C) 2014 Ondrej Zary + * Copyright (C) 2007 Richard Betts, All Rights Reserved. + * + * Based on asic3_mmc.c, copyright (c) 2005 SDG Systems, LLC and, + * sdhci.c, copyright (C) 2005-2006 Pierre Ossman + */ + +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/scatterlist.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/pm.h> +#include <linux/pm_runtime.h> +#include <linux/mmc/host.h> +#include <linux/mmc/mmc.h> + +#include "toshsd.h" + +#define DRIVER_NAME "toshsd" + +static const struct pci_device_id pci_ids[] = { + { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA, 0x0805) }, + { /* end: all zeroes */ }, +}; + +MODULE_DEVICE_TABLE(pci, pci_ids); + +static void toshsd_init(struct toshsd_host *host) +{ + /* enable clock */ + pci_write_config_byte(host->pdev, SD_PCICFG_CLKSTOP, + SD_PCICFG_CLKSTOP_ENABLE_ALL); + pci_write_config_byte(host->pdev, SD_PCICFG_CARDDETECT, 2); + + /* reset */ + iowrite16(0, host->ioaddr + SD_SOFTWARERESET); /* assert */ + mdelay(2); + iowrite16(1, host->ioaddr + SD_SOFTWARERESET); /* deassert */ + mdelay(2); + + /* Clear card registers */ + iowrite16(0, host->ioaddr + SD_CARDCLOCKCTRL); + iowrite32(0, host->ioaddr + SD_CARDSTATUS); + iowrite32(0, host->ioaddr + SD_ERRORSTATUS0); + iowrite16(0, host->ioaddr + SD_STOPINTERNAL); + + /* SDIO clock? */ + iowrite16(0x100, host->ioaddr + SDIO_BASE + SDIO_CLOCKNWAITCTRL); + + /* enable LED */ + pci_write_config_byte(host->pdev, SD_PCICFG_SDLED_ENABLE1, + SD_PCICFG_LED_ENABLE1_START); + pci_write_config_byte(host->pdev, SD_PCICFG_SDLED_ENABLE2, + SD_PCICFG_LED_ENABLE2_START); + + /* set interrupt masks */ + iowrite32(~(u32)(SD_CARD_RESP_END | SD_CARD_RW_END + | SD_CARD_CARD_REMOVED_0 | SD_CARD_CARD_INSERTED_0 + | SD_BUF_READ_ENABLE | SD_BUF_WRITE_ENABLE + | SD_BUF_CMD_TIMEOUT), + host->ioaddr + SD_INTMASKCARD); + + iowrite16(0x1000, host->ioaddr + SD_TRANSACTIONCTRL); +} + +/* Set MMC clock / power. + * Note: This controller uses a simple divider scheme therefore it cannot run + * SD/MMC cards at full speed (24/20MHz). HCLK (=33MHz PCI clock?) is too high + * and the next slowest is 16MHz (div=2). + */ +static void __toshsd_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) +{ + struct toshsd_host *host = mmc_priv(mmc); + + if (ios->clock) { + u16 clk; + int div = 1; + + while (ios->clock < HCLK / div) + div *= 2; + + clk = div >> 2; + + if (div == 1) { /* disable the divider */ + pci_write_config_byte(host->pdev, SD_PCICFG_CLKMODE, + SD_PCICFG_CLKMODE_DIV_DISABLE); + clk |= SD_CARDCLK_DIV_DISABLE; + } else + pci_write_config_byte(host->pdev, SD_PCICFG_CLKMODE, 0); + + clk |= SD_CARDCLK_ENABLE_CLOCK; + iowrite16(clk, host->ioaddr + SD_CARDCLOCKCTRL); + + mdelay(10); + } else + iowrite16(0, host->ioaddr + SD_CARDCLOCKCTRL); + + switch (ios->power_mode) { + case MMC_POWER_OFF: + pci_write_config_byte(host->pdev, SD_PCICFG_POWER1, + SD_PCICFG_PWR1_OFF); + mdelay(1); + break; + case MMC_POWER_UP: + break; + case MMC_POWER_ON: + pci_write_config_byte(host->pdev, SD_PCICFG_POWER1, + SD_PCICFG_PWR1_33V); + pci_write_config_byte(host->pdev, SD_PCICFG_POWER2, + SD_PCICFG_PWR2_AUTO); + mdelay(20); + break; + } + + switch (ios->bus_width) { + case MMC_BUS_WIDTH_1: + iowrite16(SD_CARDOPT_REQUIRED | SD_CARDOPT_DATA_RESP_TIMEOUT(14) + | SD_CARDOPT_C2_MODULE_ABSENT + | SD_CARDOPT_DATA_XFR_WIDTH_1, + host->ioaddr + SD_CARDOPTIONSETUP); + break; + case MMC_BUS_WIDTH_4: + iowrite16(SD_CARDOPT_REQUIRED | SD_CARDOPT_DATA_RESP_TIMEOUT(14) + | SD_CARDOPT_C2_MODULE_ABSENT + | SD_CARDOPT_DATA_XFR_WIDTH_4, + host->ioaddr + SD_CARDOPTIONSETUP); + break; + } +} + +static void toshsd_set_led(struct toshsd_host *host, unsigned char state) +{ + iowrite16(state, host->ioaddr + SDIO_BASE + SDIO_LEDCTRL); +} + +static void toshsd_finish_request(struct toshsd_host *host) +{ + struct mmc_request *mrq = host->mrq; + + /* Write something to end the command */ + host->mrq = NULL; + host->cmd = NULL; + host->data = NULL; + + toshsd_set_led(host, 0); + mmc_request_done(host->mmc, mrq); +} + +static irqreturn_t toshsd_thread_irq(int irq, void *dev_id) +{ + struct toshsd_host *host = dev_id; + struct mmc_data *data = host->data; + struct sg_mapping_iter *sg_miter = &host->sg_miter; + unsigned short *buf; + int count; + unsigned long flags; + + if (!data) { + dev_warn(&host->pdev->dev, "Spurious Data IRQ\n"); + if (host->cmd) { + host->cmd->error = -EIO; + toshsd_finish_request(host); + } + return IRQ_NONE; + } + spin_lock_irqsave(&host->lock, flags); + + if (!sg_miter_next(sg_miter)) + goto done; + + buf = sg_miter->addr; + + /* Ensure we dont read more than one block. The chip will interrupt us + * When the next block is available. + */ + count = sg_miter->length; + if (count > data->blksz) + count = data->blksz; + + dev_dbg(&host->pdev->dev, "count: %08x, flags %08x\n", count, + data->flags); + + /* Transfer the data */ + if (data->flags & MMC_DATA_READ) + ioread32_rep(host->ioaddr + SD_DATAPORT, buf, count >> 2); + else + iowrite32_rep(host->ioaddr + SD_DATAPORT, buf, count >> 2); + + sg_miter->consumed = count; + sg_miter_stop(sg_miter); + +done: + spin_unlock_irqrestore(&host->lock, flags); + + return IRQ_HANDLED; +} + +static void toshsd_cmd_irq(struct toshsd_host *host) +{ + struct mmc_command *cmd = host->cmd; + u8 *buf; + u16 data; + + if (!host->cmd) { + dev_warn(&host->pdev->dev, "Spurious CMD irq\n"); + return; + } + buf = (u8 *)cmd->resp; + host->cmd = NULL; + + if (cmd->flags & MMC_RSP_PRESENT && cmd->flags & MMC_RSP_136) { + /* R2 */ + buf[12] = 0xff; + data = ioread16(host->ioaddr + SD_RESPONSE0); + buf[13] = data & 0xff; + buf[14] = data >> 8; + data = ioread16(host->ioaddr + SD_RESPONSE1); + buf[15] = data & 0xff; + buf[8] = data >> 8; + data = ioread16(host->ioaddr + SD_RESPONSE2); + buf[9] = data & 0xff; + buf[10] = data >> 8; + data = ioread16(host->ioaddr + SD_RESPONSE3); + buf[11] = data & 0xff; + buf[4] = data >> 8; + data = ioread16(host->ioaddr + SD_RESPONSE4); + buf[5] = data & 0xff; + buf[6] = data >> 8; + data = ioread16(host->ioaddr + SD_RESPONSE5); + buf[7] = data & 0xff; + buf[0] = data >> 8; + data = ioread16(host->ioaddr + SD_RESPONSE6); + buf[1] = data & 0xff; + buf[2] = data >> 8; + data = ioread16(host->ioaddr + SD_RESPONSE7); + buf[3] = data & 0xff; + } else if (cmd->flags & MMC_RSP_PRESENT) { + /* R1, R1B, R3, R6, R7 */ + data = ioread16(host->ioaddr + SD_RESPONSE0); + buf[0] = data & 0xff; + buf[1] = data >> 8; + data = ioread16(host->ioaddr + SD_RESPONSE1); + buf[2] = data & 0xff; + buf[3] = data >> 8; + } + + dev_dbg(&host->pdev->dev, "Command IRQ complete %d %d %x\n", + cmd->opcode, cmd->error, cmd->flags); + + /* If there is data to handle we will + * finish the request in the mmc_data_end_irq handler.*/ + if (host->data) + return; + + toshsd_finish_request(host); +} + +static void toshsd_data_end_irq(struct toshsd_host *host) +{ + struct mmc_data *data = host->data; + + host->data = NULL; + + if (!data) { + dev_warn(&host->pdev->dev, "Spurious data end IRQ\n"); + return; + } + + if (data->error == 0) + data->bytes_xfered = data->blocks * data->blksz; + else + data->bytes_xfered = 0; + + dev_dbg(&host->pdev->dev, "Completed data request xfr=%d\n", + data->bytes_xfered); + + iowrite16(0, host->ioaddr + SD_STOPINTERNAL); + + toshsd_finish_request(host); +} + +static irqreturn_t toshsd_irq(int irq, void *dev_id) +{ + struct toshsd_host *host = dev_id; + u32 int_reg, int_mask, int_status, detail; + int error = 0, ret = IRQ_HANDLED; + + spin_lock(&host->lock); + int_status = ioread32(host->ioaddr + SD_CARDSTATUS); + int_mask = ioread32(host->ioaddr + SD_INTMASKCARD); + int_reg = int_status & ~int_mask & ~IRQ_DONT_CARE_BITS; + + dev_dbg(&host->pdev->dev, "IRQ status:%x mask:%x\n", + int_status, int_mask); + + /* nothing to do: it's not our IRQ */ + if (!int_reg) { + ret = IRQ_NONE; + goto irq_end; + } + + if (int_reg & SD_BUF_CMD_TIMEOUT) { + error = -ETIMEDOUT; + dev_dbg(&host->pdev->dev, "Timeout\n"); + } else if (int_reg & SD_BUF_CRC_ERR) { + error = -EILSEQ; + dev_err(&host->pdev->dev, "BadCRC\n"); + } else if (int_reg & (SD_BUF_ILLEGAL_ACCESS + | SD_BUF_CMD_INDEX_ERR + | SD_BUF_STOP_BIT_END_ERR + | SD_BUF_OVERFLOW + | SD_BUF_UNDERFLOW + | SD_BUF_DATA_TIMEOUT)) { + dev_err(&host->pdev->dev, "Buffer status error: { %s%s%s%s%s%s}\n", + int_reg & SD_BUF_ILLEGAL_ACCESS ? "ILLEGAL_ACC " : "", + int_reg & SD_BUF_CMD_INDEX_ERR ? "CMD_INDEX " : "", + int_reg & SD_BUF_STOP_BIT_END_ERR ? "STOPBIT_END " : "", + int_reg & SD_BUF_OVERFLOW ? "OVERFLOW " : "", + int_reg & SD_BUF_UNDERFLOW ? "UNDERFLOW " : "", + int_reg & SD_BUF_DATA_TIMEOUT ? "DATA_TIMEOUT " : ""); + + detail = ioread32(host->ioaddr + SD_ERRORSTATUS0); + dev_err(&host->pdev->dev, "detail error status { %s%s%s%s%s%s%s%s%s%s%s%s%s}\n", + detail & SD_ERR0_RESP_CMD_ERR ? "RESP_CMD " : "", + detail & SD_ERR0_RESP_NON_CMD12_END_BIT_ERR ? "RESP_END_BIT " : "", + detail & SD_ERR0_RESP_CMD12_END_BIT_ERR ? "RESP_END_BIT " : "", + detail & SD_ERR0_READ_DATA_END_BIT_ERR ? "READ_DATA_END_BIT " : "", + detail & SD_ERR0_WRITE_CRC_STATUS_END_BIT_ERR ? "WRITE_CMD_END_BIT " : "", + detail & SD_ERR0_RESP_NON_CMD12_CRC_ERR ? "RESP_CRC " : "", + detail & SD_ERR0_RESP_CMD12_CRC_ERR ? "RESP_CRC " : "", + detail & SD_ERR0_READ_DATA_CRC_ERR ? "READ_DATA_CRC " : "", + detail & SD_ERR0_WRITE_CMD_CRC_ERR ? "WRITE_CMD_CRC " : "", + detail & SD_ERR1_NO_CMD_RESP ? "NO_CMD_RESP " : "", + detail & SD_ERR1_TIMEOUT_READ_DATA ? "READ_DATA_TIMEOUT " : "", + detail & SD_ERR1_TIMEOUT_CRS_STATUS ? "CRS_STATUS_TIMEOUT " : "", + detail & SD_ERR1_TIMEOUT_CRC_BUSY ? "CRC_BUSY_TIMEOUT " : ""); + error = -EIO; + } + + if (error) { + if (host->cmd) + host->cmd->error = error; + + if (error == -ETIMEDOUT) { + iowrite32(int_status & + ~(SD_BUF_CMD_TIMEOUT | SD_CARD_RESP_END), + host->ioaddr + SD_CARDSTATUS); + } else { + toshsd_init(host); + __toshsd_set_ios(host->mmc, &host->mmc->ios); + goto irq_end; + } + } + + /* Card insert/remove. The mmc controlling code is stateless. */ + if (int_reg & (SD_CARD_CARD_INSERTED_0 | SD_CARD_CARD_REMOVED_0)) { + iowrite32(int_status & + ~(SD_CARD_CARD_REMOVED_0 | SD_CARD_CARD_INSERTED_0), + host->ioaddr + SD_CARDSTATUS); + + if (int_reg & SD_CARD_CARD_INSERTED_0) + toshsd_init(host); + + mmc_detect_change(host->mmc, 1); + } + + /* Data transfer */ + if (int_reg & (SD_BUF_READ_ENABLE | SD_BUF_WRITE_ENABLE)) { + iowrite32(int_status & + ~(SD_BUF_WRITE_ENABLE | SD_BUF_READ_ENABLE), + host->ioaddr + SD_CARDSTATUS); + + ret = IRQ_WAKE_THREAD; + goto irq_end; + } + + /* Command completion */ + if (int_reg & SD_CARD_RESP_END) { + iowrite32(int_status & ~(SD_CARD_RESP_END), + host->ioaddr + SD_CARDSTATUS); + toshsd_cmd_irq(host); + } + + /* Data transfer completion */ + if (int_reg & SD_CARD_RW_END) { + iowrite32(int_status & ~(SD_CARD_RW_END), + host->ioaddr + SD_CARDSTATUS); + toshsd_data_end_irq(host); + } +irq_end: + spin_unlock(&host->lock); + return ret; +} + +static void toshsd_start_cmd(struct toshsd_host *host, struct mmc_command *cmd) +{ + struct mmc_data *data = host->data; + int c = cmd->opcode; + + dev_dbg(&host->pdev->dev, "Command opcode: %d\n", cmd->opcode); + + if (cmd->opcode == MMC_STOP_TRANSMISSION) { + iowrite16(SD_STOPINT_ISSUE_CMD12, + host->ioaddr + SD_STOPINTERNAL); + + cmd->resp[0] = cmd->opcode; + cmd->resp[1] = 0; + cmd->resp[2] = 0; + cmd->resp[3] = 0; + + toshsd_finish_request(host); + return; + } + + switch (mmc_resp_type(cmd)) { + case MMC_RSP_NONE: + c |= SD_CMD_RESP_TYPE_NONE; + break; + + case MMC_RSP_R1: + c |= SD_CMD_RESP_TYPE_EXT_R1; + break; + case MMC_RSP_R1B: + c |= SD_CMD_RESP_TYPE_EXT_R1B; + break; + case MMC_RSP_R2: + c |= SD_CMD_RESP_TYPE_EXT_R2; + break; + case MMC_RSP_R3: + c |= SD_CMD_RESP_TYPE_EXT_R3; + break; + + default: + dev_err(&host->pdev->dev, "Unknown response type %d\n", + mmc_resp_type(cmd)); + break; + } + + host->cmd = cmd; + + if (cmd->opcode == MMC_APP_CMD) + c |= SD_CMD_TYPE_ACMD; + + if (cmd->opcode == MMC_GO_IDLE_STATE) + c |= (3 << 8); /* removed from ipaq-asic3.h for some reason */ + + if (data) { + c |= SD_CMD_DATA_PRESENT; + + if (data->blocks > 1) { + iowrite16(SD_STOPINT_AUTO_ISSUE_CMD12, + host->ioaddr + SD_STOPINTERNAL); + c |= SD_CMD_MULTI_BLOCK; + } + + if (data->flags & MMC_DATA_READ) + c |= SD_CMD_TRANSFER_READ; + + /* MMC_DATA_WRITE does not require a bit to be set */ + } + + /* Send the command */ + iowrite32(cmd->arg, host->ioaddr + SD_ARG0); + iowrite16(c, host->ioaddr + SD_CMD); +} + +static void toshsd_start_data(struct toshsd_host *host, struct mmc_data *data) +{ + unsigned int flags = SG_MITER_ATOMIC; + + dev_dbg(&host->pdev->dev, "setup data transfer: blocksize %08x nr_blocks %d, offset: %08x\n", + data->blksz, data->blocks, data->sg->offset); + + host->data = data; + + if (data->flags & MMC_DATA_READ) + flags |= SG_MITER_TO_SG; + else + flags |= SG_MITER_FROM_SG; + + sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags); + + /* Set transfer length and blocksize */ + iowrite16(data->blocks, host->ioaddr + SD_BLOCKCOUNT); + iowrite16(data->blksz, host->ioaddr + SD_CARDXFERDATALEN); +} + +/* Process requests from the MMC layer */ +static void toshsd_request(struct mmc_host *mmc, struct mmc_request *mrq) +{ + struct toshsd_host *host = mmc_priv(mmc); + unsigned long flags; + + /* abort if card not present */ + if (!(ioread16(host->ioaddr + SD_CARDSTATUS) & SD_CARD_PRESENT_0)) { + mrq->cmd->error = -ENOMEDIUM; + mmc_request_done(mmc, mrq); + return; + } + + spin_lock_irqsave(&host->lock, flags); + + WARN_ON(host->mrq != NULL); + + host->mrq = mrq; + + if (mrq->data) + toshsd_start_data(host, mrq->data); + + toshsd_set_led(host, 1); + + toshsd_start_cmd(host, mrq->cmd); + + spin_unlock_irqrestore(&host->lock, flags); +} + +static void toshsd_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) +{ + struct toshsd_host *host = mmc_priv(mmc); + unsigned long flags; + + spin_lock_irqsave(&host->lock, flags); + __toshsd_set_ios(mmc, ios); + spin_unlock_irqrestore(&host->lock, flags); +} + +static int toshsd_get_ro(struct mmc_host *mmc) +{ + struct toshsd_host *host = mmc_priv(mmc); + + /* active low */ + return !(ioread16(host->ioaddr + SD_CARDSTATUS) & SD_CARD_WRITE_PROTECT); +} + +static int toshsd_get_cd(struct mmc_host *mmc) +{ + struct toshsd_host *host = mmc_priv(mmc); + + return !!(ioread16(host->ioaddr + SD_CARDSTATUS) & SD_CARD_PRESENT_0); +} + +static const struct mmc_host_ops toshsd_ops = { + .request = toshsd_request, + .set_ios = toshsd_set_ios, + .get_ro = toshsd_get_ro, + .get_cd = toshsd_get_cd, +}; + + +static void toshsd_powerdown(struct toshsd_host *host) +{ + /* mask all interrupts */ + iowrite32(0xffffffff, host->ioaddr + SD_INTMASKCARD); + /* disable card clock */ + iowrite16(0x000, host->ioaddr + SDIO_BASE + SDIO_CLOCKNWAITCTRL); + iowrite16(0, host->ioaddr + SD_CARDCLOCKCTRL); + /* power down card */ + pci_write_config_byte(host->pdev, SD_PCICFG_POWER1, SD_PCICFG_PWR1_OFF); + /* disable clock */ + pci_write_config_byte(host->pdev, SD_PCICFG_CLKSTOP, 0); +} + +#ifdef CONFIG_PM_SLEEP +static int toshsd_pm_suspend(struct device *dev) +{ + struct pci_dev *pdev = to_pci_dev(dev); + struct toshsd_host *host = pci_get_drvdata(pdev); + + toshsd_powerdown(host); + + pci_save_state(pdev); + pci_enable_wake(pdev, PCI_D3hot, 0); + pci_disable_device(pdev); + pci_set_power_state(pdev, PCI_D3hot); + + return 0; +} + +static int toshsd_pm_resume(struct device *dev) +{ + struct pci_dev *pdev = to_pci_dev(dev); + struct toshsd_host *host = pci_get_drvdata(pdev); + int ret; + + pci_set_power_state(pdev, PCI_D0); + pci_restore_state(pdev); + ret = pci_enable_device(pdev); + if (ret) + return ret; + + toshsd_init(host); + + return 0; +} +#endif /* CONFIG_PM_SLEEP */ + +static int toshsd_probe(struct pci_dev *pdev, const struct pci_device_id *ent) +{ + int ret; + struct toshsd_host *host; + struct mmc_host *mmc; + resource_size_t base; + + ret = pci_enable_device(pdev); + if (ret) + return ret; + + mmc = mmc_alloc_host(sizeof(struct toshsd_host), &pdev->dev); + if (!mmc) { + ret = -ENOMEM; + goto err; + } + + host = mmc_priv(mmc); + host->mmc = mmc; + + host->pdev = pdev; + pci_set_drvdata(pdev, host); + + ret = pci_request_regions(pdev, DRIVER_NAME); + if (ret) + goto free; + + host->ioaddr = pci_iomap(pdev, 0, 0); + if (!host->ioaddr) { + ret = -ENOMEM; + goto release; + } + + /* Set MMC host parameters */ + mmc->ops = &toshsd_ops; + mmc->caps = MMC_CAP_4_BIT_DATA; + mmc->ocr_avail = MMC_VDD_32_33; + + mmc->f_min = HCLK / 512; + mmc->f_max = HCLK; + + spin_lock_init(&host->lock); + + toshsd_init(host); + + ret = request_threaded_irq(pdev->irq, toshsd_irq, toshsd_thread_irq, + IRQF_SHARED, DRIVER_NAME, host); + if (ret) + goto unmap; + + ret = mmc_add_host(mmc); + if (ret) + goto free_irq; + + base = pci_resource_start(pdev, 0); + dev_dbg(&pdev->dev, "MMIO %pa, IRQ %d\n", &base, pdev->irq); + + pm_suspend_ignore_children(&pdev->dev, 1); + + return 0; + +free_irq: + free_irq(pdev->irq, host); +unmap: + pci_iounmap(pdev, host->ioaddr); +release: + pci_release_regions(pdev); +free: + mmc_free_host(mmc); + pci_set_drvdata(pdev, NULL); +err: + pci_disable_device(pdev); + return ret; +} + +static void toshsd_remove(struct pci_dev *pdev) +{ + struct toshsd_host *host = pci_get_drvdata(pdev); + + mmc_remove_host(host->mmc); + toshsd_powerdown(host); + free_irq(pdev->irq, host); + pci_iounmap(pdev, host->ioaddr); + pci_release_regions(pdev); + mmc_free_host(host->mmc); + pci_set_drvdata(pdev, NULL); + pci_disable_device(pdev); +} + +static const struct dev_pm_ops toshsd_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(toshsd_pm_suspend, toshsd_pm_resume) +}; + +static struct pci_driver toshsd_driver = { + .name = DRIVER_NAME, + .id_table = pci_ids, + .probe = toshsd_probe, + .remove = toshsd_remove, + .driver.pm = &toshsd_pm_ops, +}; + +module_pci_driver(toshsd_driver); + +MODULE_AUTHOR("Ondrej Zary, Richard Betts"); +MODULE_DESCRIPTION("Toshiba PCI Secure Digital Host Controller Interface driver"); +MODULE_LICENSE("GPL"); |