diff options
Diffstat (limited to 'drivers/mtd/chips/Kconfig')
| -rw-r--r-- | drivers/mtd/chips/Kconfig | 243 |
1 files changed, 243 insertions, 0 deletions
diff --git a/drivers/mtd/chips/Kconfig b/drivers/mtd/chips/Kconfig new file mode 100644 index 0000000000..19726ebd97 --- /dev/null +++ b/drivers/mtd/chips/Kconfig @@ -0,0 +1,243 @@ +# SPDX-License-Identifier: GPL-2.0-only +menu "RAM/ROM/Flash chip drivers" + depends on MTD!=n + +config MTD_CFI + tristate "Detect flash chips by Common Flash Interface (CFI) probe" + select MTD_GEN_PROBE + select MTD_CFI_UTIL + help + The Common Flash Interface specification was developed by Intel, + AMD and other flash manufactures that provides a universal method + for probing the capabilities of flash devices. If you wish to + support any device that is CFI-compliant, you need to enable this + option. Visit <https://www.amd.com/products/nvd/overview/cfi.html> + for more information on CFI. + +config MTD_JEDECPROBE + tristate "Detect non-CFI AMD/JEDEC-compatible flash chips" + select MTD_GEN_PROBE + select MTD_CFI_UTIL + help + This option enables JEDEC-style probing of flash chips which are not + compatible with the Common Flash Interface, but will use the common + CFI-targeted flash drivers for any chips which are identified which + are in fact compatible in all but the probe method. This actually + covers most AMD/Fujitsu-compatible chips and also non-CFI + Intel chips. + +config MTD_GEN_PROBE + tristate + +config MTD_CFI_ADV_OPTIONS + bool "Flash chip driver advanced configuration options" + depends on MTD_GEN_PROBE + help + If you need to specify a specific endianness for access to flash + chips, or if you wish to reduce the size of the kernel by including + support for only specific arrangements of flash chips, say 'Y'. This + option does not directly affect the code, but will enable other + configuration options which allow you to do so. + + If unsure, say 'N'. + +choice + prompt "Flash cmd/query data swapping" + depends on MTD_CFI_ADV_OPTIONS + default MTD_CFI_NOSWAP + help + This option defines the way in which the CPU attempts to arrange + data bits when writing the 'magic' commands to the chips. Saying + 'NO', which is the default when CONFIG_MTD_CFI_ADV_OPTIONS isn't + enabled, means that the CPU will not do any swapping; the chips + are expected to be wired to the CPU in 'host-endian' form. + Specific arrangements are possible with the BIG_ENDIAN_BYTE and + LITTLE_ENDIAN_BYTE, if the bytes are reversed. + +config MTD_CFI_NOSWAP + depends on !ARCH_IXP4XX || CPU_BIG_ENDIAN + bool "NO" + +config MTD_CFI_BE_BYTE_SWAP + bool "BIG_ENDIAN_BYTE" + +config MTD_CFI_LE_BYTE_SWAP + depends on !ARCH_IXP4XX + bool "LITTLE_ENDIAN_BYTE" + +endchoice + +config MTD_CFI_GEOMETRY + bool "Specific CFI Flash geometry selection" + depends on MTD_CFI_ADV_OPTIONS + select MTD_MAP_BANK_WIDTH_1 if !(MTD_MAP_BANK_WIDTH_2 || \ + MTD_MAP_BANK_WIDTH_4 || MTD_MAP_BANK_WIDTH_8 || \ + MTD_MAP_BANK_WIDTH_16 || MTD_MAP_BANK_WIDTH_32) + select MTD_CFI_I1 if !(MTD_CFI_I2 || MTD_CFI_I4 || MTD_CFI_I8) + help + This option does not affect the code directly, but will enable + some other configuration options which would allow you to reduce + the size of the kernel by including support for only certain + arrangements of CFI chips. If unsure, say 'N' and all options + which are supported by the current code will be enabled. + +config MTD_MAP_BANK_WIDTH_1 + bool "Support 8-bit buswidth" if MTD_CFI_GEOMETRY + default y + help + If you wish to support CFI devices on a physical bus which is + 8 bits wide, say 'Y'. + +config MTD_MAP_BANK_WIDTH_2 + bool "Support 16-bit buswidth" if MTD_CFI_GEOMETRY + default y + help + If you wish to support CFI devices on a physical bus which is + 16 bits wide, say 'Y'. + +config MTD_MAP_BANK_WIDTH_4 + bool "Support 32-bit buswidth" if MTD_CFI_GEOMETRY + default y + help + If you wish to support CFI devices on a physical bus which is + 32 bits wide, say 'Y'. + +config MTD_MAP_BANK_WIDTH_8 + bool "Support 64-bit buswidth" if MTD_CFI_GEOMETRY + default n + help + If you wish to support CFI devices on a physical bus which is + 64 bits wide, say 'Y'. + +config MTD_MAP_BANK_WIDTH_16 + bool "Support 128-bit buswidth" if MTD_CFI_GEOMETRY + default n + help + If you wish to support CFI devices on a physical bus which is + 128 bits wide, say 'Y'. + +config MTD_MAP_BANK_WIDTH_32 + bool "Support 256-bit buswidth" if MTD_CFI_GEOMETRY + select MTD_COMPLEX_MAPPINGS if HAS_IOMEM + default n + help + If you wish to support CFI devices on a physical bus which is + 256 bits wide, say 'Y'. + +config MTD_CFI_I1 + bool "Support 1-chip flash interleave" if MTD_CFI_GEOMETRY + default y + help + If your flash chips are not interleaved - i.e. you only have one + flash chip addressed by each bus cycle, then say 'Y'. + +config MTD_CFI_I2 + bool "Support 2-chip flash interleave" if MTD_CFI_GEOMETRY + default y + help + If your flash chips are interleaved in pairs - i.e. you have two + flash chips addressed by each bus cycle, then say 'Y'. + +config MTD_CFI_I4 + bool "Support 4-chip flash interleave" if MTD_CFI_GEOMETRY + default n + help + If your flash chips are interleaved in fours - i.e. you have four + flash chips addressed by each bus cycle, then say 'Y'. + +config MTD_CFI_I8 + bool "Support 8-chip flash interleave" if MTD_CFI_GEOMETRY + default n + help + If your flash chips are interleaved in eights - i.e. you have eight + flash chips addressed by each bus cycle, then say 'Y'. + +config MTD_OTP + bool "Protection Registers aka one-time programmable (OTP) bits" + depends on MTD_CFI_ADV_OPTIONS + default n + help + This enables support for reading, writing and locking so called + "Protection Registers" present on some flash chips. + A subset of them are pre-programmed at the factory with a + unique set of values. The rest is user-programmable. + + The user-programmable Protection Registers contain one-time + programmable (OTP) bits; when programmed, register bits cannot be + erased. Each Protection Register can be accessed multiple times to + program individual bits, as long as the register remains unlocked. + + Each Protection Register has an associated Lock Register bit. When a + Lock Register bit is programmed, the associated Protection Register + can only be read; it can no longer be programmed. Additionally, + because the Lock Register bits themselves are OTP, when programmed, + Lock Register bits cannot be erased. Therefore, when a Protection + Register is locked, it cannot be unlocked. + + This feature should therefore be used with extreme care. Any mistake + in the programming of OTP bits will waste them. + +config MTD_CFI_INTELEXT + tristate "Support for CFI command set 0001 (Intel/Sharp chips)" + depends on MTD_GEN_PROBE + select MTD_CFI_UTIL + help + The Common Flash Interface defines a number of different command + sets which a CFI-compliant chip may claim to implement. This code + provides support for command set 0001, used on Intel StrataFlash + and other parts. + +config MTD_CFI_AMDSTD + tristate "Support for CFI command set 0002 (AMD/Fujitsu/Spansion chips)" + depends on MTD_GEN_PROBE + select MTD_CFI_UTIL + help + The Common Flash Interface defines a number of different command + sets which a CFI-compliant chip may claim to implement. This code + provides support for command set 0002, used on chips including + the AMD Am29LV320. + +config MTD_CFI_STAA + tristate "Support for CFI command set 0020 (ST (Advanced Architecture) chips)" + depends on MTD_GEN_PROBE + select MTD_CFI_UTIL + help + The Common Flash Interface defines a number of different command + sets which a CFI-compliant chip may claim to implement. This code + provides support for command set 0020. + +config MTD_CFI_UTIL + tristate + +config MTD_RAM + tristate "Support for RAM chips in bus mapping" + help + This option enables basic support for RAM chips accessed through + a bus mapping driver. + +config MTD_ROM + tristate "Support for ROM chips in bus mapping" + help + This option enables basic support for ROM chips accessed through + a bus mapping driver. + +config MTD_ABSENT + tristate "Support for absent chips in bus mapping" + help + This option enables support for a dummy probing driver used to + allocated placeholder MTD devices on systems that have socketed + or removable media. Use of this driver as a fallback chip probe + preserves the expected registration order of MTD device nodes on + the system regardless of media presence. Device nodes created + with this driver will return -ENODEV upon access. + +config MTD_XIP + bool "XIP aware MTD support" + depends on !SMP && (MTD_CFI_INTELEXT || MTD_CFI_AMDSTD) && ARCH_MTD_XIP + default y if XIP_KERNEL + help + This allows MTD support to work with flash memory which is also + used for XIP purposes. If you're not sure what this is all about + then say N. + +endmenu |