diff options
Diffstat (limited to 'drivers/net/dsa/microchip')
| -rw-r--r-- | drivers/net/dsa/microchip/ksz8.h | 4 | ||||
| -rw-r--r-- | drivers/net/dsa/microchip/ksz8795.c | 152 | ||||
| -rw-r--r-- | drivers/net/dsa/microchip/ksz8795_reg.h | 3 | ||||
| -rw-r--r-- | drivers/net/dsa/microchip/ksz_common.c | 34 | ||||
| -rw-r--r-- | drivers/net/dsa/microchip/ksz_common.h | 21 |
5 files changed, 173 insertions, 41 deletions
diff --git a/drivers/net/dsa/microchip/ksz8.h b/drivers/net/dsa/microchip/ksz8.h index 4cea811e73..1a5225264e 100644 --- a/drivers/net/dsa/microchip/ksz8.h +++ b/drivers/net/dsa/microchip/ksz8.h @@ -56,5 +56,9 @@ int ksz8_reset_switch(struct ksz_device *dev); int ksz8_switch_init(struct ksz_device *dev); void ksz8_switch_exit(struct ksz_device *dev); int ksz8_change_mtu(struct ksz_device *dev, int port, int mtu); +void ksz8_phylink_mac_link_up(struct ksz_device *dev, int port, + unsigned int mode, phy_interface_t interface, + struct phy_device *phydev, int speed, int duplex, + bool tx_pause, bool rx_pause); #endif diff --git a/drivers/net/dsa/microchip/ksz8795.c b/drivers/net/dsa/microchip/ksz8795.c index 9048d1f196..c3da97abce 100644 --- a/drivers/net/dsa/microchip/ksz8795.c +++ b/drivers/net/dsa/microchip/ksz8795.c @@ -1358,6 +1358,9 @@ static void ksz8795_cpu_interface_select(struct ksz_device *dev, int port) { struct ksz_port *p = &dev->ports[port]; + if (!ksz_is_ksz87xx(dev)) + return; + if (!p->interface && dev->compat_interface) { dev_warn(dev->dev, "Using legacy switch \"phy-mode\" property, because it is missing on port %d node. " @@ -1391,18 +1394,29 @@ void ksz8_port_setup(struct ksz_device *dev, int port, bool cpu_port) /* enable 802.1p priority */ ksz_port_cfg(dev, port, P_PRIO_CTRL, PORT_802_1P_ENABLE, true); - if (cpu_port) { - if (!ksz_is_ksz88x3(dev)) - ksz8795_cpu_interface_select(dev, port); - + if (cpu_port) member = dsa_user_ports(ds); - } else { + else member = BIT(dsa_upstream_port(ds, port)); - } ksz8_cfg_port_member(dev, port, member); } +static void ksz88x3_config_rmii_clk(struct ksz_device *dev) +{ + struct dsa_port *cpu_dp = dsa_to_port(dev->ds, dev->cpu_port); + bool rmii_clk_internal; + + if (!ksz_is_ksz88x3(dev)) + return; + + rmii_clk_internal = of_property_read_bool(cpu_dp->dn, + "microchip,rmii-clk-internal"); + + ksz_cfg(dev, KSZ88X3_REG_FVID_AND_HOST_MODE, + KSZ88X3_PORT3_RMII_CLK_INTERNAL, rmii_clk_internal); +} + void ksz8_config_cpu_port(struct dsa_switch *ds) { struct ksz_device *dev = ds->priv; @@ -1419,6 +1433,9 @@ void ksz8_config_cpu_port(struct dsa_switch *ds) ksz8_port_setup(dev, dev->cpu_port, true); + ksz8795_cpu_interface_select(dev, dev->cpu_port); + ksz88x3_config_rmii_clk(dev); + for (i = 0; i < dev->phy_port_cnt; i++) { ksz_port_stp_state_set(ds, i, BR_STATE_DISABLED); } @@ -1439,6 +1456,127 @@ void ksz8_config_cpu_port(struct dsa_switch *ds) } } +/** + * ksz8_phy_port_link_up - Configures ports with integrated PHYs + * @dev: The KSZ device instance. + * @port: The port number to configure. + * @duplex: The desired duplex mode. + * @tx_pause: If true, enables transmit pause. + * @rx_pause: If true, enables receive pause. + * + * Description: + * The function configures flow control settings for a given port based on the + * desired settings and current duplex mode. + * + * According to the KSZ8873 datasheet, the PORT_FORCE_FLOW_CTRL bit in the + * Port Control 2 register (0x1A for Port 1, 0x22 for Port 2, 0x32 for Port 3) + * determines how flow control is handled on the port: + * "1 = will always enable full-duplex flow control on the port, regardless + * of AN result. + * 0 = full-duplex flow control is enabled based on AN result." + * + * This means that the flow control behavior depends on the state of this bit: + * - If PORT_FORCE_FLOW_CTRL is set to 1, the switch will ignore AN results and + * force flow control on the port. + * - If PORT_FORCE_FLOW_CTRL is set to 0, the switch will enable or disable + * flow control based on the AN results. + * + * However, there is a potential limitation in this configuration. It is + * currently not possible to force disable flow control on a port if we still + * advertise pause support. While such a configuration is not currently + * supported by Linux, and may not make practical sense, it's important to be + * aware of this limitation when working with the KSZ8873 and similar devices. + */ +static void ksz8_phy_port_link_up(struct ksz_device *dev, int port, int duplex, + bool tx_pause, bool rx_pause) +{ + const u16 *regs = dev->info->regs; + u8 sctrl = 0; + + /* The KSZ8795 switch differs from the KSZ8873 by supporting + * asymmetric pause control. However, since a single bit is used to + * control both RX and TX pause, we can't enforce asymmetric pause + * control - both TX and RX pause will be either enabled or disabled + * together. + * + * If auto-negotiation is enabled, we usually allow the flow control to + * be determined by the auto-negotiation process based on the + * capabilities of both link partners. However, for KSZ8873, the + * PORT_FORCE_FLOW_CTRL bit may be set by the hardware bootstrap, + * ignoring the auto-negotiation result. Thus, even in auto-negotiation + * mode, we need to ensure that the PORT_FORCE_FLOW_CTRL bit is + * properly cleared. + * + * In the absence of pause auto-negotiation, we will enforce symmetric + * pause control for both variants of switches - KSZ8873 and KSZ8795. + * + * Autoneg Pause Autoneg rx,tx PORT_FORCE_FLOW_CTRL + * 1 1 x 0 + * 0 1 x 0 (flow control probably disabled) + * x 0 1 1 (flow control force enabled) + * 1 0 0 0 (flow control still depends on + * aneg result due to hardware) + * 0 0 0 0 (flow control probably disabled) + */ + if (dev->ports[port].manual_flow && tx_pause) + sctrl |= PORT_FORCE_FLOW_CTRL; + + ksz_prmw8(dev, port, regs[P_STP_CTRL], PORT_FORCE_FLOW_CTRL, sctrl); +} + +/** + * ksz8_cpu_port_link_up - Configures the CPU port of the switch. + * @dev: The KSZ device instance. + * @speed: The desired link speed. + * @duplex: The desired duplex mode. + * @tx_pause: If true, enables transmit pause. + * @rx_pause: If true, enables receive pause. + * + * Description: + * The function configures flow control and speed settings for the CPU + * port of the switch based on the desired settings, current duplex mode, and + * speed. + */ +static void ksz8_cpu_port_link_up(struct ksz_device *dev, int speed, int duplex, + bool tx_pause, bool rx_pause) +{ + const u16 *regs = dev->info->regs; + u8 ctrl = 0; + + /* SW_FLOW_CTRL, SW_HALF_DUPLEX, and SW_10_MBIT bits are bootstrappable + * at least on KSZ8873. They can have different values depending on your + * board setup. + */ + if (tx_pause || rx_pause) + ctrl |= SW_FLOW_CTRL; + + if (duplex == DUPLEX_HALF) + ctrl |= SW_HALF_DUPLEX; + + /* This hardware only supports SPEED_10 and SPEED_100. For SPEED_10 + * we need to set the SW_10_MBIT bit. Otherwise, we can leave it 0. + */ + if (speed == SPEED_10) + ctrl |= SW_10_MBIT; + + ksz_rmw8(dev, regs[S_BROADCAST_CTRL], SW_HALF_DUPLEX | SW_FLOW_CTRL | + SW_10_MBIT, ctrl); +} + +void ksz8_phylink_mac_link_up(struct ksz_device *dev, int port, + unsigned int mode, phy_interface_t interface, + struct phy_device *phydev, int speed, int duplex, + bool tx_pause, bool rx_pause) +{ + /* If the port is the CPU port, apply special handling. Only the CPU + * port is configured via global registers. + */ + if (dev->cpu_port == port) + ksz8_cpu_port_link_up(dev, speed, duplex, tx_pause, rx_pause); + else if (dev->info->internal_phy[port]) + ksz8_phy_port_link_up(dev, port, duplex, tx_pause, rx_pause); +} + static int ksz8_handle_global_errata(struct dsa_switch *ds) { struct ksz_device *dev = ds->priv; @@ -1487,8 +1625,6 @@ int ksz8_setup(struct dsa_switch *ds) */ ds->vlan_filtering_is_global = true; - ksz_cfg(dev, S_REPLACE_VID_CTRL, SW_FLOW_CTRL, true); - /* Enable automatic fast aging when link changed detected. */ ksz_cfg(dev, S_LINK_AGING_CTRL, SW_LINK_AUTO_AGING, true); diff --git a/drivers/net/dsa/microchip/ksz8795_reg.h b/drivers/net/dsa/microchip/ksz8795_reg.h index 3c9dae53e4..beca974e01 100644 --- a/drivers/net/dsa/microchip/ksz8795_reg.h +++ b/drivers/net/dsa/microchip/ksz8795_reg.h @@ -22,6 +22,9 @@ #define KSZ8863_GLOBAL_SOFTWARE_RESET BIT(4) #define KSZ8863_PCS_RESET BIT(0) +#define KSZ88X3_REG_FVID_AND_HOST_MODE 0xC6 +#define KSZ88X3_PORT3_RMII_CLK_INTERNAL BIT(3) + #define REG_SW_CTRL_0 0x02 #define SW_NEW_BACKOFF BIT(7) diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c index d5d7e48b7b..25a49708f4 100644 --- a/drivers/net/dsa/microchip/ksz_common.c +++ b/drivers/net/dsa/microchip/ksz_common.c @@ -277,6 +277,7 @@ static const struct ksz_dev_ops ksz8_dev_ops = { .mirror_add = ksz8_port_mirror_add, .mirror_del = ksz8_port_mirror_del, .get_caps = ksz8_get_caps, + .phylink_mac_link_up = ksz8_phylink_mac_link_up, .config_cpu_port = ksz8_config_cpu_port, .enable_stp_addr = ksz8_enable_stp_addr, .reset = ksz8_reset_switch, @@ -1672,15 +1673,23 @@ static const struct ksz_chip_data *ksz_lookup_info(unsigned int prod_num) static int ksz_check_device_id(struct ksz_device *dev) { - const struct ksz_chip_data *dt_chip_data; + const struct ksz_chip_data *expected_chip_data; + u32 expected_chip_id; - dt_chip_data = of_device_get_match_data(dev->dev); + if (dev->pdata) { + expected_chip_id = dev->pdata->chip_id; + expected_chip_data = ksz_lookup_info(expected_chip_id); + if (WARN_ON(!expected_chip_data)) + return -ENODEV; + } else { + expected_chip_data = of_device_get_match_data(dev->dev); + expected_chip_id = expected_chip_data->chip_id; + } - /* Check for Device Tree and Chip ID */ - if (dt_chip_data->chip_id != dev->chip_id) { + if (expected_chip_id != dev->chip_id) { dev_err(dev->dev, "Device tree specifies chip %s but found %s, please fix it!\n", - dt_chip_data->dev_name, dev->info->dev_name); + expected_chip_data->dev_name, dev->info->dev_name); return -ENODEV; } @@ -2709,7 +2718,7 @@ static enum dsa_tag_protocol ksz_get_tag_protocol(struct dsa_switch *ds, proto = DSA_TAG_PROTO_KSZ9477; if (is_lan937x(dev)) - proto = DSA_TAG_PROTO_LAN937X_VALUE; + proto = DSA_TAG_PROTO_LAN937X; return proto; } @@ -2980,8 +2989,10 @@ static void ksz_phylink_mac_config(struct dsa_switch *ds, int port, { struct ksz_device *dev = ds->priv; - if (ksz_is_ksz88x3(dev)) + if (ksz_is_ksz88x3(dev)) { + dev->ports[port].manual_flow = !(state->pause & MLO_PAUSE_AN); return; + } /* Internal PHYs */ if (dev->info->internal_phy[port]) @@ -3124,10 +3135,8 @@ static void ksz_phylink_mac_link_up(struct dsa_switch *ds, int port, { struct ksz_device *dev = ds->priv; - if (dev->dev_ops->phylink_mac_link_up) - dev->dev_ops->phylink_mac_link_up(dev, port, mode, interface, - phydev, speed, duplex, - tx_pause, rx_pause); + dev->dev_ops->phylink_mac_link_up(dev, port, mode, interface, phydev, + speed, duplex, tx_pause, rx_pause); } static int ksz_switch_detect(struct ksz_device *dev) @@ -4169,9 +4178,6 @@ int ksz_switch_register(struct ksz_device *dev) int ret; int i; - if (dev->pdata) - dev->chip_id = dev->pdata->chip_id; - dev->reset_gpio = devm_gpiod_get_optional(dev->dev, "reset", GPIOD_OUT_LOW); if (IS_ERR(dev->reset_gpio)) diff --git a/drivers/net/dsa/microchip/ksz_common.h b/drivers/net/dsa/microchip/ksz_common.h index b7e8a403a1..15612101a1 100644 --- a/drivers/net/dsa/microchip/ksz_common.h +++ b/drivers/net/dsa/microchip/ksz_common.h @@ -14,6 +14,7 @@ #include <linux/regmap.h> #include <net/dsa.h> #include <linux/irq.h> +#include <linux/platform_data/microchip-ksz.h> #include "ksz_ptp.h" @@ -134,6 +135,7 @@ struct ksz_port { ktime_t tstamp_msg; struct completion tstamp_msg_comp; #endif + bool manual_flow; }; struct ksz_device { @@ -202,25 +204,6 @@ enum ksz_model { LAN9374, }; -enum ksz_chip_id { - KSZ8563_CHIP_ID = 0x8563, - KSZ8795_CHIP_ID = 0x8795, - KSZ8794_CHIP_ID = 0x8794, - KSZ8765_CHIP_ID = 0x8765, - KSZ8830_CHIP_ID = 0x8830, - KSZ9477_CHIP_ID = 0x00947700, - KSZ9896_CHIP_ID = 0x00989600, - KSZ9897_CHIP_ID = 0x00989700, - KSZ9893_CHIP_ID = 0x00989300, - KSZ9563_CHIP_ID = 0x00956300, - KSZ9567_CHIP_ID = 0x00956700, - LAN9370_CHIP_ID = 0x00937000, - LAN9371_CHIP_ID = 0x00937100, - LAN9372_CHIP_ID = 0x00937200, - LAN9373_CHIP_ID = 0x00937300, - LAN9374_CHIP_ID = 0x00937400, -}; - enum ksz_regs { REG_SW_MAC_ADDR, REG_IND_CTRL_0, |