summaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/intel/e1000e/80003es2lan.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/ethernet/intel/e1000e/80003es2lan.c')
-rw-r--r--drivers/net/ethernet/intel/e1000e/80003es2lan.c1412
1 files changed, 1412 insertions, 0 deletions
diff --git a/drivers/net/ethernet/intel/e1000e/80003es2lan.c b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
new file mode 100644
index 000000000..be9c695dd
--- /dev/null
+++ b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
@@ -0,0 +1,1412 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright(c) 1999 - 2018 Intel Corporation. */
+
+/* 80003ES2LAN Gigabit Ethernet Controller (Copper)
+ * 80003ES2LAN Gigabit Ethernet Controller (Serdes)
+ */
+
+#include "e1000.h"
+
+/* A table for the GG82563 cable length where the range is defined
+ * with a lower bound at "index" and the upper bound at
+ * "index + 5".
+ */
+static const u16 e1000_gg82563_cable_length_table[] = {
+ 0, 60, 115, 150, 150, 60, 115, 150, 180, 180, 0xFF
+};
+
+#define GG82563_CABLE_LENGTH_TABLE_SIZE \
+ ARRAY_SIZE(e1000_gg82563_cable_length_table)
+
+static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw);
+static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask);
+static void e1000_release_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask);
+static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw);
+static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw);
+static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw);
+static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex);
+static s32 e1000_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
+ u16 *data);
+static s32 e1000_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
+ u16 data);
+static void e1000_power_down_phy_copper_80003es2lan(struct e1000_hw *hw);
+
+/**
+ * e1000_init_phy_params_80003es2lan - Init ESB2 PHY func ptrs.
+ * @hw: pointer to the HW structure
+ **/
+static s32 e1000_init_phy_params_80003es2lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+
+ if (hw->phy.media_type != e1000_media_type_copper) {
+ phy->type = e1000_phy_none;
+ return 0;
+ } else {
+ phy->ops.power_up = e1000_power_up_phy_copper;
+ phy->ops.power_down = e1000_power_down_phy_copper_80003es2lan;
+ }
+
+ phy->addr = 1;
+ phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+ phy->reset_delay_us = 100;
+ phy->type = e1000_phy_gg82563;
+
+ /* This can only be done after all function pointers are setup. */
+ ret_val = e1000e_get_phy_id(hw);
+
+ /* Verify phy id */
+ if (phy->id != GG82563_E_PHY_ID)
+ return -E1000_ERR_PHY;
+
+ return ret_val;
+}
+
+/**
+ * e1000_init_nvm_params_80003es2lan - Init ESB2 NVM func ptrs.
+ * @hw: pointer to the HW structure
+ **/
+static s32 e1000_init_nvm_params_80003es2lan(struct e1000_hw *hw)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ u32 eecd = er32(EECD);
+ u16 size;
+
+ nvm->opcode_bits = 8;
+ nvm->delay_usec = 1;
+ switch (nvm->override) {
+ case e1000_nvm_override_spi_large:
+ nvm->page_size = 32;
+ nvm->address_bits = 16;
+ break;
+ case e1000_nvm_override_spi_small:
+ nvm->page_size = 8;
+ nvm->address_bits = 8;
+ break;
+ default:
+ nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8;
+ nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8;
+ break;
+ }
+
+ nvm->type = e1000_nvm_eeprom_spi;
+
+ size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
+ E1000_EECD_SIZE_EX_SHIFT);
+
+ /* Added to a constant, "size" becomes the left-shift value
+ * for setting word_size.
+ */
+ size += NVM_WORD_SIZE_BASE_SHIFT;
+
+ /* EEPROM access above 16k is unsupported */
+ if (size > 14)
+ size = 14;
+ nvm->word_size = BIT(size);
+
+ return 0;
+}
+
+/**
+ * e1000_init_mac_params_80003es2lan - Init ESB2 MAC func ptrs.
+ * @hw: pointer to the HW structure
+ **/
+static s32 e1000_init_mac_params_80003es2lan(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+
+ /* Set media type and media-dependent function pointers */
+ switch (hw->adapter->pdev->device) {
+ case E1000_DEV_ID_80003ES2LAN_SERDES_DPT:
+ hw->phy.media_type = e1000_media_type_internal_serdes;
+ mac->ops.check_for_link = e1000e_check_for_serdes_link;
+ mac->ops.setup_physical_interface =
+ e1000e_setup_fiber_serdes_link;
+ break;
+ default:
+ hw->phy.media_type = e1000_media_type_copper;
+ mac->ops.check_for_link = e1000e_check_for_copper_link;
+ mac->ops.setup_physical_interface =
+ e1000_setup_copper_link_80003es2lan;
+ break;
+ }
+
+ /* Set mta register count */
+ mac->mta_reg_count = 128;
+ /* Set rar entry count */
+ mac->rar_entry_count = E1000_RAR_ENTRIES;
+ /* FWSM register */
+ mac->has_fwsm = true;
+ /* ARC supported; valid only if manageability features are enabled. */
+ mac->arc_subsystem_valid = !!(er32(FWSM) & E1000_FWSM_MODE_MASK);
+ /* Adaptive IFS not supported */
+ mac->adaptive_ifs = false;
+
+ /* set lan id for port to determine which phy lock to use */
+ hw->mac.ops.set_lan_id(hw);
+
+ return 0;
+}
+
+static s32 e1000_get_variants_80003es2lan(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ s32 rc;
+
+ rc = e1000_init_mac_params_80003es2lan(hw);
+ if (rc)
+ return rc;
+
+ rc = e1000_init_nvm_params_80003es2lan(hw);
+ if (rc)
+ return rc;
+
+ rc = e1000_init_phy_params_80003es2lan(hw);
+ if (rc)
+ return rc;
+
+ return 0;
+}
+
+/**
+ * e1000_acquire_phy_80003es2lan - Acquire rights to access PHY
+ * @hw: pointer to the HW structure
+ *
+ * A wrapper to acquire access rights to the correct PHY.
+ **/
+static s32 e1000_acquire_phy_80003es2lan(struct e1000_hw *hw)
+{
+ u16 mask;
+
+ mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM;
+ return e1000_acquire_swfw_sync_80003es2lan(hw, mask);
+}
+
+/**
+ * e1000_release_phy_80003es2lan - Release rights to access PHY
+ * @hw: pointer to the HW structure
+ *
+ * A wrapper to release access rights to the correct PHY.
+ **/
+static void e1000_release_phy_80003es2lan(struct e1000_hw *hw)
+{
+ u16 mask;
+
+ mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM;
+ e1000_release_swfw_sync_80003es2lan(hw, mask);
+}
+
+/**
+ * e1000_acquire_mac_csr_80003es2lan - Acquire right to access Kumeran register
+ * @hw: pointer to the HW structure
+ *
+ * Acquire the semaphore to access the Kumeran interface.
+ *
+ **/
+static s32 e1000_acquire_mac_csr_80003es2lan(struct e1000_hw *hw)
+{
+ u16 mask;
+
+ mask = E1000_SWFW_CSR_SM;
+
+ return e1000_acquire_swfw_sync_80003es2lan(hw, mask);
+}
+
+/**
+ * e1000_release_mac_csr_80003es2lan - Release right to access Kumeran Register
+ * @hw: pointer to the HW structure
+ *
+ * Release the semaphore used to access the Kumeran interface
+ **/
+static void e1000_release_mac_csr_80003es2lan(struct e1000_hw *hw)
+{
+ u16 mask;
+
+ mask = E1000_SWFW_CSR_SM;
+
+ e1000_release_swfw_sync_80003es2lan(hw, mask);
+}
+
+/**
+ * e1000_acquire_nvm_80003es2lan - Acquire rights to access NVM
+ * @hw: pointer to the HW structure
+ *
+ * Acquire the semaphore to access the EEPROM.
+ **/
+static s32 e1000_acquire_nvm_80003es2lan(struct e1000_hw *hw)
+{
+ s32 ret_val;
+
+ ret_val = e1000_acquire_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000e_acquire_nvm(hw);
+
+ if (ret_val)
+ e1000_release_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM);
+
+ return ret_val;
+}
+
+/**
+ * e1000_release_nvm_80003es2lan - Relinquish rights to access NVM
+ * @hw: pointer to the HW structure
+ *
+ * Release the semaphore used to access the EEPROM.
+ **/
+static void e1000_release_nvm_80003es2lan(struct e1000_hw *hw)
+{
+ e1000e_release_nvm(hw);
+ e1000_release_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM);
+}
+
+/**
+ * e1000_acquire_swfw_sync_80003es2lan - Acquire SW/FW semaphore
+ * @hw: pointer to the HW structure
+ * @mask: specifies which semaphore to acquire
+ *
+ * Acquire the SW/FW semaphore to access the PHY or NVM. The mask
+ * will also specify which port we're acquiring the lock for.
+ **/
+static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask)
+{
+ u32 swfw_sync;
+ u32 swmask = mask;
+ u32 fwmask = mask << 16;
+ s32 i = 0;
+ s32 timeout = 50;
+
+ while (i < timeout) {
+ if (e1000e_get_hw_semaphore(hw))
+ return -E1000_ERR_SWFW_SYNC;
+
+ swfw_sync = er32(SW_FW_SYNC);
+ if (!(swfw_sync & (fwmask | swmask)))
+ break;
+
+ /* Firmware currently using resource (fwmask)
+ * or other software thread using resource (swmask)
+ */
+ e1000e_put_hw_semaphore(hw);
+ mdelay(5);
+ i++;
+ }
+
+ if (i == timeout) {
+ e_dbg("Driver can't access resource, SW_FW_SYNC timeout.\n");
+ return -E1000_ERR_SWFW_SYNC;
+ }
+
+ swfw_sync |= swmask;
+ ew32(SW_FW_SYNC, swfw_sync);
+
+ e1000e_put_hw_semaphore(hw);
+
+ return 0;
+}
+
+/**
+ * e1000_release_swfw_sync_80003es2lan - Release SW/FW semaphore
+ * @hw: pointer to the HW structure
+ * @mask: specifies which semaphore to acquire
+ *
+ * Release the SW/FW semaphore used to access the PHY or NVM. The mask
+ * will also specify which port we're releasing the lock for.
+ **/
+static void e1000_release_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask)
+{
+ u32 swfw_sync;
+
+ while (e1000e_get_hw_semaphore(hw) != 0)
+ ; /* Empty */
+
+ swfw_sync = er32(SW_FW_SYNC);
+ swfw_sync &= ~mask;
+ ew32(SW_FW_SYNC, swfw_sync);
+
+ e1000e_put_hw_semaphore(hw);
+}
+
+/**
+ * e1000_read_phy_reg_gg82563_80003es2lan - Read GG82563 PHY register
+ * @hw: pointer to the HW structure
+ * @offset: offset of the register to read
+ * @data: pointer to the data returned from the operation
+ *
+ * Read the GG82563 PHY register.
+ **/
+static s32 e1000_read_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
+ u32 offset, u16 *data)
+{
+ s32 ret_val;
+ u32 page_select;
+ u16 temp;
+
+ ret_val = e1000_acquire_phy_80003es2lan(hw);
+ if (ret_val)
+ return ret_val;
+
+ /* Select Configuration Page */
+ if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
+ page_select = GG82563_PHY_PAGE_SELECT;
+ } else {
+ /* Use Alternative Page Select register to access
+ * registers 30 and 31
+ */
+ page_select = GG82563_PHY_PAGE_SELECT_ALT;
+ }
+
+ temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT);
+ ret_val = e1000e_write_phy_reg_mdic(hw, page_select, temp);
+ if (ret_val) {
+ e1000_release_phy_80003es2lan(hw);
+ return ret_val;
+ }
+
+ if (hw->dev_spec.e80003es2lan.mdic_wa_enable) {
+ /* The "ready" bit in the MDIC register may be incorrectly set
+ * before the device has completed the "Page Select" MDI
+ * transaction. So we wait 200us after each MDI command...
+ */
+ usleep_range(200, 400);
+
+ /* ...and verify the command was successful. */
+ ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp);
+
+ if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) {
+ e1000_release_phy_80003es2lan(hw);
+ return -E1000_ERR_PHY;
+ }
+
+ usleep_range(200, 400);
+
+ ret_val = e1000e_read_phy_reg_mdic(hw,
+ MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+ usleep_range(200, 400);
+ } else {
+ ret_val = e1000e_read_phy_reg_mdic(hw,
+ MAX_PHY_REG_ADDRESS & offset,
+ data);
+ }
+
+ e1000_release_phy_80003es2lan(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000_write_phy_reg_gg82563_80003es2lan - Write GG82563 PHY register
+ * @hw: pointer to the HW structure
+ * @offset: offset of the register to read
+ * @data: value to write to the register
+ *
+ * Write to the GG82563 PHY register.
+ **/
+static s32 e1000_write_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
+ u32 offset, u16 data)
+{
+ s32 ret_val;
+ u32 page_select;
+ u16 temp;
+
+ ret_val = e1000_acquire_phy_80003es2lan(hw);
+ if (ret_val)
+ return ret_val;
+
+ /* Select Configuration Page */
+ if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
+ page_select = GG82563_PHY_PAGE_SELECT;
+ } else {
+ /* Use Alternative Page Select register to access
+ * registers 30 and 31
+ */
+ page_select = GG82563_PHY_PAGE_SELECT_ALT;
+ }
+
+ temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT);
+ ret_val = e1000e_write_phy_reg_mdic(hw, page_select, temp);
+ if (ret_val) {
+ e1000_release_phy_80003es2lan(hw);
+ return ret_val;
+ }
+
+ if (hw->dev_spec.e80003es2lan.mdic_wa_enable) {
+ /* The "ready" bit in the MDIC register may be incorrectly set
+ * before the device has completed the "Page Select" MDI
+ * transaction. So we wait 200us after each MDI command...
+ */
+ usleep_range(200, 400);
+
+ /* ...and verify the command was successful. */
+ ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp);
+
+ if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) {
+ e1000_release_phy_80003es2lan(hw);
+ return -E1000_ERR_PHY;
+ }
+
+ usleep_range(200, 400);
+
+ ret_val = e1000e_write_phy_reg_mdic(hw,
+ MAX_PHY_REG_ADDRESS &
+ offset, data);
+
+ usleep_range(200, 400);
+ } else {
+ ret_val = e1000e_write_phy_reg_mdic(hw,
+ MAX_PHY_REG_ADDRESS &
+ offset, data);
+ }
+
+ e1000_release_phy_80003es2lan(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000_write_nvm_80003es2lan - Write to ESB2 NVM
+ * @hw: pointer to the HW structure
+ * @offset: offset of the register to read
+ * @words: number of words to write
+ * @data: buffer of data to write to the NVM
+ *
+ * Write "words" of data to the ESB2 NVM.
+ **/
+static s32 e1000_write_nvm_80003es2lan(struct e1000_hw *hw, u16 offset,
+ u16 words, u16 *data)
+{
+ return e1000e_write_nvm_spi(hw, offset, words, data);
+}
+
+/**
+ * e1000_get_cfg_done_80003es2lan - Wait for configuration to complete
+ * @hw: pointer to the HW structure
+ *
+ * Wait a specific amount of time for manageability processes to complete.
+ * This is a function pointer entry point called by the phy module.
+ **/
+static s32 e1000_get_cfg_done_80003es2lan(struct e1000_hw *hw)
+{
+ s32 timeout = PHY_CFG_TIMEOUT;
+ u32 mask = E1000_NVM_CFG_DONE_PORT_0;
+
+ if (hw->bus.func == 1)
+ mask = E1000_NVM_CFG_DONE_PORT_1;
+
+ while (timeout) {
+ if (er32(EEMNGCTL) & mask)
+ break;
+ usleep_range(1000, 2000);
+ timeout--;
+ }
+ if (!timeout) {
+ e_dbg("MNG configuration cycle has not completed.\n");
+ return -E1000_ERR_RESET;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_phy_force_speed_duplex_80003es2lan - Force PHY speed and duplex
+ * @hw: pointer to the HW structure
+ *
+ * Force the speed and duplex settings onto the PHY. This is a
+ * function pointer entry point called by the phy module.
+ **/
+static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 phy_data;
+ bool link;
+
+ /* Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
+ * forced whenever speed and duplex are forced.
+ */
+ ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_AUTO;
+ ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ e_dbg("GG82563 PSCR: %X\n", phy_data);
+
+ ret_val = e1e_rphy(hw, MII_BMCR, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
+
+ /* Reset the phy to commit changes. */
+ phy_data |= BMCR_RESET;
+
+ ret_val = e1e_wphy(hw, MII_BMCR, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ udelay(1);
+
+ if (hw->phy.autoneg_wait_to_complete) {
+ e_dbg("Waiting for forced speed/duplex link on GG82563 phy.\n");
+
+ ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT,
+ 100000, &link);
+ if (ret_val)
+ return ret_val;
+
+ if (!link) {
+ /* We didn't get link.
+ * Reset the DSP and cross our fingers.
+ */
+ ret_val = e1000e_phy_reset_dsp(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* Try once more */
+ ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT,
+ 100000, &link);
+ if (ret_val)
+ return ret_val;
+ }
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_MAC_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Resetting the phy means we need to verify the TX_CLK corresponds
+ * to the link speed. 10Mbps -> 2.5MHz, else 25MHz.
+ */
+ phy_data &= ~GG82563_MSCR_TX_CLK_MASK;
+ if (hw->mac.forced_speed_duplex & E1000_ALL_10_SPEED)
+ phy_data |= GG82563_MSCR_TX_CLK_10MBPS_2_5;
+ else
+ phy_data |= GG82563_MSCR_TX_CLK_100MBPS_25;
+
+ /* In addition, we must re-enable CRS on Tx for both half and full
+ * duplex.
+ */
+ phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
+ ret_val = e1e_wphy(hw, GG82563_PHY_MAC_SPEC_CTRL, phy_data);
+
+ return ret_val;
+}
+
+/**
+ * e1000_get_cable_length_80003es2lan - Set approximate cable length
+ * @hw: pointer to the HW structure
+ *
+ * Find the approximate cable length as measured by the GG82563 PHY.
+ * This is a function pointer entry point called by the phy module.
+ **/
+static s32 e1000_get_cable_length_80003es2lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data, index;
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_DSP_DISTANCE, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ index = phy_data & GG82563_DSPD_CABLE_LENGTH;
+
+ if (index >= GG82563_CABLE_LENGTH_TABLE_SIZE - 5)
+ return -E1000_ERR_PHY;
+
+ phy->min_cable_length = e1000_gg82563_cable_length_table[index];
+ phy->max_cable_length = e1000_gg82563_cable_length_table[index + 5];
+
+ phy->cable_length = (phy->min_cable_length + phy->max_cable_length) / 2;
+
+ return 0;
+}
+
+/**
+ * e1000_get_link_up_info_80003es2lan - Report speed and duplex
+ * @hw: pointer to the HW structure
+ * @speed: pointer to speed buffer
+ * @duplex: pointer to duplex buffer
+ *
+ * Retrieve the current speed and duplex configuration.
+ **/
+static s32 e1000_get_link_up_info_80003es2lan(struct e1000_hw *hw, u16 *speed,
+ u16 *duplex)
+{
+ s32 ret_val;
+
+ if (hw->phy.media_type == e1000_media_type_copper) {
+ ret_val = e1000e_get_speed_and_duplex_copper(hw, speed, duplex);
+ hw->phy.ops.cfg_on_link_up(hw);
+ } else {
+ ret_val = e1000e_get_speed_and_duplex_fiber_serdes(hw,
+ speed,
+ duplex);
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000_reset_hw_80003es2lan - Reset the ESB2 controller
+ * @hw: pointer to the HW structure
+ *
+ * Perform a global reset to the ESB2 controller.
+ **/
+static s32 e1000_reset_hw_80003es2lan(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 ret_val;
+ u16 kum_reg_data;
+
+ /* Prevent the PCI-E bus from sticking if there is no TLP connection
+ * on the last TLP read/write transaction when MAC is reset.
+ */
+ ret_val = e1000e_disable_pcie_master(hw);
+ if (ret_val)
+ e_dbg("PCI-E Master disable polling has failed.\n");
+
+ e_dbg("Masking off all interrupts\n");
+ ew32(IMC, 0xffffffff);
+
+ ew32(RCTL, 0);
+ ew32(TCTL, E1000_TCTL_PSP);
+ e1e_flush();
+
+ usleep_range(10000, 11000);
+
+ ctrl = er32(CTRL);
+
+ ret_val = e1000_acquire_phy_80003es2lan(hw);
+ if (ret_val)
+ return ret_val;
+
+ e_dbg("Issuing a global reset to MAC\n");
+ ew32(CTRL, ctrl | E1000_CTRL_RST);
+ e1000_release_phy_80003es2lan(hw);
+
+ /* Disable IBIST slave mode (far-end loopback) */
+ ret_val =
+ e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM,
+ &kum_reg_data);
+ if (!ret_val) {
+ kum_reg_data |= E1000_KMRNCTRLSTA_IBIST_DISABLE;
+ ret_val = e1000_write_kmrn_reg_80003es2lan(hw,
+ E1000_KMRNCTRLSTA_INBAND_PARAM,
+ kum_reg_data);
+ if (ret_val)
+ e_dbg("Error disabling far-end loopback\n");
+ } else {
+ e_dbg("Error disabling far-end loopback\n");
+ }
+
+ ret_val = e1000e_get_auto_rd_done(hw);
+ if (ret_val)
+ /* We don't want to continue accessing MAC registers. */
+ return ret_val;
+
+ /* Clear any pending interrupt events. */
+ ew32(IMC, 0xffffffff);
+ er32(ICR);
+
+ return e1000_check_alt_mac_addr_generic(hw);
+}
+
+/**
+ * e1000_init_hw_80003es2lan - Initialize the ESB2 controller
+ * @hw: pointer to the HW structure
+ *
+ * Initialize the hw bits, LED, VFTA, MTA, link and hw counters.
+ **/
+static s32 e1000_init_hw_80003es2lan(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 reg_data;
+ s32 ret_val;
+ u16 kum_reg_data;
+ u16 i;
+
+ e1000_initialize_hw_bits_80003es2lan(hw);
+
+ /* Initialize identification LED */
+ ret_val = mac->ops.id_led_init(hw);
+ /* An error is not fatal and we should not stop init due to this */
+ if (ret_val)
+ e_dbg("Error initializing identification LED\n");
+
+ /* Disabling VLAN filtering */
+ e_dbg("Initializing the IEEE VLAN\n");
+ mac->ops.clear_vfta(hw);
+
+ /* Setup the receive address. */
+ e1000e_init_rx_addrs(hw, mac->rar_entry_count);
+
+ /* Zero out the Multicast HASH table */
+ e_dbg("Zeroing the MTA\n");
+ for (i = 0; i < mac->mta_reg_count; i++)
+ E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0);
+
+ /* Setup link and flow control */
+ ret_val = mac->ops.setup_link(hw);
+ if (ret_val)
+ return ret_val;
+
+ /* Disable IBIST slave mode (far-end loopback) */
+ ret_val =
+ e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM,
+ &kum_reg_data);
+ if (!ret_val) {
+ kum_reg_data |= E1000_KMRNCTRLSTA_IBIST_DISABLE;
+ ret_val = e1000_write_kmrn_reg_80003es2lan(hw,
+ E1000_KMRNCTRLSTA_INBAND_PARAM,
+ kum_reg_data);
+ if (ret_val)
+ e_dbg("Error disabling far-end loopback\n");
+ } else {
+ e_dbg("Error disabling far-end loopback\n");
+ }
+
+ /* Set the transmit descriptor write-back policy */
+ reg_data = er32(TXDCTL(0));
+ reg_data = ((reg_data & ~E1000_TXDCTL_WTHRESH) |
+ E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC);
+ ew32(TXDCTL(0), reg_data);
+
+ /* ...for both queues. */
+ reg_data = er32(TXDCTL(1));
+ reg_data = ((reg_data & ~E1000_TXDCTL_WTHRESH) |
+ E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC);
+ ew32(TXDCTL(1), reg_data);
+
+ /* Enable retransmit on late collisions */
+ reg_data = er32(TCTL);
+ reg_data |= E1000_TCTL_RTLC;
+ ew32(TCTL, reg_data);
+
+ /* Configure Gigabit Carry Extend Padding */
+ reg_data = er32(TCTL_EXT);
+ reg_data &= ~E1000_TCTL_EXT_GCEX_MASK;
+ reg_data |= DEFAULT_TCTL_EXT_GCEX_80003ES2LAN;
+ ew32(TCTL_EXT, reg_data);
+
+ /* Configure Transmit Inter-Packet Gap */
+ reg_data = er32(TIPG);
+ reg_data &= ~E1000_TIPG_IPGT_MASK;
+ reg_data |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN;
+ ew32(TIPG, reg_data);
+
+ reg_data = E1000_READ_REG_ARRAY(hw, E1000_FFLT, 0x0001);
+ reg_data &= ~0x00100000;
+ E1000_WRITE_REG_ARRAY(hw, E1000_FFLT, 0x0001, reg_data);
+
+ /* default to true to enable the MDIC W/A */
+ hw->dev_spec.e80003es2lan.mdic_wa_enable = true;
+
+ ret_val =
+ e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_OFFSET >>
+ E1000_KMRNCTRLSTA_OFFSET_SHIFT, &i);
+ if (!ret_val) {
+ if ((i & E1000_KMRNCTRLSTA_OPMODE_MASK) ==
+ E1000_KMRNCTRLSTA_OPMODE_INBAND_MDIO)
+ hw->dev_spec.e80003es2lan.mdic_wa_enable = false;
+ }
+
+ /* Clear all of the statistics registers (clear on read). It is
+ * important that we do this after we have tried to establish link
+ * because the symbol error count will increment wildly if there
+ * is no link.
+ */
+ e1000_clear_hw_cntrs_80003es2lan(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000_initialize_hw_bits_80003es2lan - Init hw bits of ESB2
+ * @hw: pointer to the HW structure
+ *
+ * Initializes required hardware-dependent bits needed for normal operation.
+ **/
+static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw)
+{
+ u32 reg;
+
+ /* Transmit Descriptor Control 0 */
+ reg = er32(TXDCTL(0));
+ reg |= BIT(22);
+ ew32(TXDCTL(0), reg);
+
+ /* Transmit Descriptor Control 1 */
+ reg = er32(TXDCTL(1));
+ reg |= BIT(22);
+ ew32(TXDCTL(1), reg);
+
+ /* Transmit Arbitration Control 0 */
+ reg = er32(TARC(0));
+ reg &= ~(0xF << 27); /* 30:27 */
+ if (hw->phy.media_type != e1000_media_type_copper)
+ reg &= ~BIT(20);
+ ew32(TARC(0), reg);
+
+ /* Transmit Arbitration Control 1 */
+ reg = er32(TARC(1));
+ if (er32(TCTL) & E1000_TCTL_MULR)
+ reg &= ~BIT(28);
+ else
+ reg |= BIT(28);
+ ew32(TARC(1), reg);
+
+ /* Disable IPv6 extension header parsing because some malformed
+ * IPv6 headers can hang the Rx.
+ */
+ reg = er32(RFCTL);
+ reg |= (E1000_RFCTL_IPV6_EX_DIS | E1000_RFCTL_NEW_IPV6_EXT_DIS);
+ ew32(RFCTL, reg);
+}
+
+/**
+ * e1000_copper_link_setup_gg82563_80003es2lan - Configure GG82563 Link
+ * @hw: pointer to the HW structure
+ *
+ * Setup some GG82563 PHY registers for obtaining link
+ **/
+static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u32 reg;
+ u16 data;
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_MAC_SPEC_CTRL, &data);
+ if (ret_val)
+ return ret_val;
+
+ data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
+ /* Use 25MHz for both link down and 1000Base-T for Tx clock. */
+ data |= GG82563_MSCR_TX_CLK_1000MBPS_25;
+
+ ret_val = e1e_wphy(hw, GG82563_PHY_MAC_SPEC_CTRL, data);
+ if (ret_val)
+ return ret_val;
+
+ /* Options:
+ * MDI/MDI-X = 0 (default)
+ * 0 - Auto for all speeds
+ * 1 - MDI mode
+ * 2 - MDI-X mode
+ * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
+ */
+ ret_val = e1e_rphy(hw, GG82563_PHY_SPEC_CTRL, &data);
+ if (ret_val)
+ return ret_val;
+
+ data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK;
+
+ switch (phy->mdix) {
+ case 1:
+ data |= GG82563_PSCR_CROSSOVER_MODE_MDI;
+ break;
+ case 2:
+ data |= GG82563_PSCR_CROSSOVER_MODE_MDIX;
+ break;
+ case 0:
+ default:
+ data |= GG82563_PSCR_CROSSOVER_MODE_AUTO;
+ break;
+ }
+
+ /* Options:
+ * disable_polarity_correction = 0 (default)
+ * Automatic Correction for Reversed Cable Polarity
+ * 0 - Disabled
+ * 1 - Enabled
+ */
+ data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
+ if (phy->disable_polarity_correction)
+ data |= GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
+
+ ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL, data);
+ if (ret_val)
+ return ret_val;
+
+ /* SW Reset the PHY so all changes take effect */
+ ret_val = hw->phy.ops.commit(hw);
+ if (ret_val) {
+ e_dbg("Error Resetting the PHY\n");
+ return ret_val;
+ }
+
+ /* Bypass Rx and Tx FIFO's */
+ reg = E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL;
+ data = (E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS |
+ E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS);
+ ret_val = e1000_write_kmrn_reg_80003es2lan(hw, reg, data);
+ if (ret_val)
+ return ret_val;
+
+ reg = E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE;
+ ret_val = e1000_read_kmrn_reg_80003es2lan(hw, reg, &data);
+ if (ret_val)
+ return ret_val;
+ data |= E1000_KMRNCTRLSTA_OPMODE_E_IDLE;
+ ret_val = e1000_write_kmrn_reg_80003es2lan(hw, reg, data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_SPEC_CTRL_2, &data);
+ if (ret_val)
+ return ret_val;
+
+ data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG;
+ ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL_2, data);
+ if (ret_val)
+ return ret_val;
+
+ reg = er32(CTRL_EXT);
+ reg &= ~E1000_CTRL_EXT_LINK_MODE_MASK;
+ ew32(CTRL_EXT, reg);
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_PWR_MGMT_CTRL, &data);
+ if (ret_val)
+ return ret_val;
+
+ /* Do not init these registers when the HW is in IAMT mode, since the
+ * firmware will have already initialized them. We only initialize
+ * them if the HW is not in IAMT mode.
+ */
+ if (!hw->mac.ops.check_mng_mode(hw)) {
+ /* Enable Electrical Idle on the PHY */
+ data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE;
+ ret_val = e1e_wphy(hw, GG82563_PHY_PWR_MGMT_CTRL, data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &data);
+ if (ret_val)
+ return ret_val;
+
+ data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
+ ret_val = e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* Workaround: Disable padding in Kumeran interface in the MAC
+ * and in the PHY to avoid CRC errors.
+ */
+ ret_val = e1e_rphy(hw, GG82563_PHY_INBAND_CTRL, &data);
+ if (ret_val)
+ return ret_val;
+
+ data |= GG82563_ICR_DIS_PADDING;
+ ret_val = e1e_wphy(hw, GG82563_PHY_INBAND_CTRL, data);
+ if (ret_val)
+ return ret_val;
+
+ return 0;
+}
+
+/**
+ * e1000_setup_copper_link_80003es2lan - Setup Copper Link for ESB2
+ * @hw: pointer to the HW structure
+ *
+ * Essentially a wrapper for setting up all things "copper" related.
+ * This is a function pointer entry point called by the mac module.
+ **/
+static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 ret_val;
+ u16 reg_data;
+
+ ctrl = er32(CTRL);
+ ctrl |= E1000_CTRL_SLU;
+ ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ ew32(CTRL, ctrl);
+
+ /* Set the mac to wait the maximum time between each
+ * iteration and increase the max iterations when
+ * polling the phy; this fixes erroneous timeouts at 10Mbps.
+ */
+ ret_val = e1000_write_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 4),
+ 0xFFFF);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_read_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 9),
+ &reg_data);
+ if (ret_val)
+ return ret_val;
+ reg_data |= 0x3F;
+ ret_val = e1000_write_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 9),
+ reg_data);
+ if (ret_val)
+ return ret_val;
+ ret_val =
+ e1000_read_kmrn_reg_80003es2lan(hw,
+ E1000_KMRNCTRLSTA_OFFSET_INB_CTRL,
+ &reg_data);
+ if (ret_val)
+ return ret_val;
+ reg_data |= E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING;
+ ret_val =
+ e1000_write_kmrn_reg_80003es2lan(hw,
+ E1000_KMRNCTRLSTA_OFFSET_INB_CTRL,
+ reg_data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_copper_link_setup_gg82563_80003es2lan(hw);
+ if (ret_val)
+ return ret_val;
+
+ return e1000e_setup_copper_link(hw);
+}
+
+/**
+ * e1000_cfg_on_link_up_80003es2lan - es2 link configuration after link-up
+ * @hw: pointer to the HW structure
+ *
+ * Configure the KMRN interface by applying last minute quirks for
+ * 10/100 operation.
+ **/
+static s32 e1000_cfg_on_link_up_80003es2lan(struct e1000_hw *hw)
+{
+ s32 ret_val = 0;
+ u16 speed;
+ u16 duplex;
+
+ if (hw->phy.media_type == e1000_media_type_copper) {
+ ret_val = e1000e_get_speed_and_duplex_copper(hw, &speed,
+ &duplex);
+ if (ret_val)
+ return ret_val;
+
+ if (speed == SPEED_1000)
+ ret_val = e1000_cfg_kmrn_1000_80003es2lan(hw);
+ else
+ ret_val = e1000_cfg_kmrn_10_100_80003es2lan(hw, duplex);
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000_cfg_kmrn_10_100_80003es2lan - Apply "quirks" for 10/100 operation
+ * @hw: pointer to the HW structure
+ * @duplex: current duplex setting
+ *
+ * Configure the KMRN interface by applying last minute quirks for
+ * 10/100 operation.
+ **/
+static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex)
+{
+ s32 ret_val;
+ u32 tipg;
+ u32 i = 0;
+ u16 reg_data, reg_data2;
+
+ reg_data = E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT;
+ ret_val =
+ e1000_write_kmrn_reg_80003es2lan(hw,
+ E1000_KMRNCTRLSTA_OFFSET_HD_CTRL,
+ reg_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Configure Transmit Inter-Packet Gap */
+ tipg = er32(TIPG);
+ tipg &= ~E1000_TIPG_IPGT_MASK;
+ tipg |= DEFAULT_TIPG_IPGT_10_100_80003ES2LAN;
+ ew32(TIPG, tipg);
+
+ do {
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data2);
+ if (ret_val)
+ return ret_val;
+ i++;
+ } while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY));
+
+ if (duplex == HALF_DUPLEX)
+ reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER;
+ else
+ reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
+
+ return e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
+}
+
+/**
+ * e1000_cfg_kmrn_1000_80003es2lan - Apply "quirks" for gigabit operation
+ * @hw: pointer to the HW structure
+ *
+ * Configure the KMRN interface by applying last minute quirks for
+ * gigabit operation.
+ **/
+static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 reg_data, reg_data2;
+ u32 tipg;
+ u32 i = 0;
+
+ reg_data = E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT;
+ ret_val =
+ e1000_write_kmrn_reg_80003es2lan(hw,
+ E1000_KMRNCTRLSTA_OFFSET_HD_CTRL,
+ reg_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Configure Transmit Inter-Packet Gap */
+ tipg = er32(TIPG);
+ tipg &= ~E1000_TIPG_IPGT_MASK;
+ tipg |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN;
+ ew32(TIPG, tipg);
+
+ do {
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data2);
+ if (ret_val)
+ return ret_val;
+ i++;
+ } while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY));
+
+ reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
+
+ return e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
+}
+
+/**
+ * e1000_read_kmrn_reg_80003es2lan - Read kumeran register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquire semaphore, then read the PHY register at offset
+ * using the kumeran interface. The information retrieved is stored in data.
+ * Release the semaphore before exiting.
+ **/
+static s32 e1000_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
+ u16 *data)
+{
+ u32 kmrnctrlsta;
+ s32 ret_val;
+
+ ret_val = e1000_acquire_mac_csr_80003es2lan(hw);
+ if (ret_val)
+ return ret_val;
+
+ kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) &
+ E1000_KMRNCTRLSTA_OFFSET) | E1000_KMRNCTRLSTA_REN;
+ ew32(KMRNCTRLSTA, kmrnctrlsta);
+ e1e_flush();
+
+ udelay(2);
+
+ kmrnctrlsta = er32(KMRNCTRLSTA);
+ *data = (u16)kmrnctrlsta;
+
+ e1000_release_mac_csr_80003es2lan(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000_write_kmrn_reg_80003es2lan - Write kumeran register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquire semaphore, then write the data to PHY register
+ * at the offset using the kumeran interface. Release semaphore
+ * before exiting.
+ **/
+static s32 e1000_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
+ u16 data)
+{
+ u32 kmrnctrlsta;
+ s32 ret_val;
+
+ ret_val = e1000_acquire_mac_csr_80003es2lan(hw);
+ if (ret_val)
+ return ret_val;
+
+ kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) &
+ E1000_KMRNCTRLSTA_OFFSET) | data;
+ ew32(KMRNCTRLSTA, kmrnctrlsta);
+ e1e_flush();
+
+ udelay(2);
+
+ e1000_release_mac_csr_80003es2lan(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000_read_mac_addr_80003es2lan - Read device MAC address
+ * @hw: pointer to the HW structure
+ **/
+static s32 e1000_read_mac_addr_80003es2lan(struct e1000_hw *hw)
+{
+ s32 ret_val;
+
+ /* If there's an alternate MAC address place it in RAR0
+ * so that it will override the Si installed default perm
+ * address.
+ */
+ ret_val = e1000_check_alt_mac_addr_generic(hw);
+ if (ret_val)
+ return ret_val;
+
+ return e1000_read_mac_addr_generic(hw);
+}
+
+/**
+ * e1000_power_down_phy_copper_80003es2lan - Remove link during PHY power down
+ * @hw: pointer to the HW structure
+ *
+ * In the case of a PHY power down to save power, or to turn off link during a
+ * driver unload, or wake on lan is not enabled, remove the link.
+ **/
+static void e1000_power_down_phy_copper_80003es2lan(struct e1000_hw *hw)
+{
+ /* If the management interface is not enabled, then power down */
+ if (!(hw->mac.ops.check_mng_mode(hw) ||
+ hw->phy.ops.check_reset_block(hw)))
+ e1000_power_down_phy_copper(hw);
+}
+
+/**
+ * e1000_clear_hw_cntrs_80003es2lan - Clear device specific hardware counters
+ * @hw: pointer to the HW structure
+ *
+ * Clears the hardware counters by reading the counter registers.
+ **/
+static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw)
+{
+ e1000e_clear_hw_cntrs_base(hw);
+
+ er32(PRC64);
+ er32(PRC127);
+ er32(PRC255);
+ er32(PRC511);
+ er32(PRC1023);
+ er32(PRC1522);
+ er32(PTC64);
+ er32(PTC127);
+ er32(PTC255);
+ er32(PTC511);
+ er32(PTC1023);
+ er32(PTC1522);
+
+ er32(ALGNERRC);
+ er32(RXERRC);
+ er32(TNCRS);
+ er32(CEXTERR);
+ er32(TSCTC);
+ er32(TSCTFC);
+
+ er32(MGTPRC);
+ er32(MGTPDC);
+ er32(MGTPTC);
+
+ er32(IAC);
+ er32(ICRXOC);
+
+ er32(ICRXPTC);
+ er32(ICRXATC);
+ er32(ICTXPTC);
+ er32(ICTXATC);
+ er32(ICTXQEC);
+ er32(ICTXQMTC);
+ er32(ICRXDMTC);
+}
+
+static const struct e1000_mac_operations es2_mac_ops = {
+ .read_mac_addr = e1000_read_mac_addr_80003es2lan,
+ .id_led_init = e1000e_id_led_init_generic,
+ .blink_led = e1000e_blink_led_generic,
+ .check_mng_mode = e1000e_check_mng_mode_generic,
+ /* check_for_link dependent on media type */
+ .cleanup_led = e1000e_cleanup_led_generic,
+ .clear_hw_cntrs = e1000_clear_hw_cntrs_80003es2lan,
+ .get_bus_info = e1000e_get_bus_info_pcie,
+ .set_lan_id = e1000_set_lan_id_multi_port_pcie,
+ .get_link_up_info = e1000_get_link_up_info_80003es2lan,
+ .led_on = e1000e_led_on_generic,
+ .led_off = e1000e_led_off_generic,
+ .update_mc_addr_list = e1000e_update_mc_addr_list_generic,
+ .write_vfta = e1000_write_vfta_generic,
+ .clear_vfta = e1000_clear_vfta_generic,
+ .reset_hw = e1000_reset_hw_80003es2lan,
+ .init_hw = e1000_init_hw_80003es2lan,
+ .setup_link = e1000e_setup_link_generic,
+ /* setup_physical_interface dependent on media type */
+ .setup_led = e1000e_setup_led_generic,
+ .config_collision_dist = e1000e_config_collision_dist_generic,
+ .rar_set = e1000e_rar_set_generic,
+ .rar_get_count = e1000e_rar_get_count_generic,
+};
+
+static const struct e1000_phy_operations es2_phy_ops = {
+ .acquire = e1000_acquire_phy_80003es2lan,
+ .check_polarity = e1000_check_polarity_m88,
+ .check_reset_block = e1000e_check_reset_block_generic,
+ .commit = e1000e_phy_sw_reset,
+ .force_speed_duplex = e1000_phy_force_speed_duplex_80003es2lan,
+ .get_cfg_done = e1000_get_cfg_done_80003es2lan,
+ .get_cable_length = e1000_get_cable_length_80003es2lan,
+ .get_info = e1000e_get_phy_info_m88,
+ .read_reg = e1000_read_phy_reg_gg82563_80003es2lan,
+ .release = e1000_release_phy_80003es2lan,
+ .reset = e1000e_phy_hw_reset_generic,
+ .set_d0_lplu_state = NULL,
+ .set_d3_lplu_state = e1000e_set_d3_lplu_state,
+ .write_reg = e1000_write_phy_reg_gg82563_80003es2lan,
+ .cfg_on_link_up = e1000_cfg_on_link_up_80003es2lan,
+};
+
+static const struct e1000_nvm_operations es2_nvm_ops = {
+ .acquire = e1000_acquire_nvm_80003es2lan,
+ .read = e1000e_read_nvm_eerd,
+ .release = e1000_release_nvm_80003es2lan,
+ .reload = e1000e_reload_nvm_generic,
+ .update = e1000e_update_nvm_checksum_generic,
+ .valid_led_default = e1000e_valid_led_default,
+ .validate = e1000e_validate_nvm_checksum_generic,
+ .write = e1000_write_nvm_80003es2lan,
+};
+
+const struct e1000_info e1000_es2_info = {
+ .mac = e1000_80003es2lan,
+ .flags = FLAG_HAS_HW_VLAN_FILTER
+ | FLAG_HAS_JUMBO_FRAMES
+ | FLAG_HAS_WOL
+ | FLAG_APME_IN_CTRL3
+ | FLAG_HAS_CTRLEXT_ON_LOAD
+ | FLAG_RX_NEEDS_RESTART /* errata */
+ | FLAG_TARC_SET_BIT_ZERO /* errata */
+ | FLAG_APME_CHECK_PORT_B
+ | FLAG_DISABLE_FC_PAUSE_TIME, /* errata */
+ .flags2 = FLAG2_DMA_BURST,
+ .pba = 38,
+ .max_hw_frame_size = DEFAULT_JUMBO,
+ .get_variants = e1000_get_variants_80003es2lan,
+ .mac_ops = &es2_mac_ops,
+ .phy_ops = &es2_phy_ops,
+ .nvm_ops = &es2_nvm_ops,
+};