diff options
Diffstat (limited to 'drivers/net/ethernet/ti/icssg/icssg_config.h')
-rw-r--r-- | drivers/net/ethernet/ti/icssg/icssg_config.h | 56 |
1 files changed, 56 insertions, 0 deletions
diff --git a/drivers/net/ethernet/ti/icssg/icssg_config.h b/drivers/net/ethernet/ti/icssg/icssg_config.h index 43eb092217..cf2ea4bd22 100644 --- a/drivers/net/ethernet/ti/icssg/icssg_config.h +++ b/drivers/net/ethernet/ti/icssg/icssg_config.h @@ -109,6 +109,62 @@ enum icssg_port_state_cmd { #define ICSSG_FLAG_MASK 0xff00ffff +/* SR1.0-specific bits */ +#define PRUETH_MAX_RX_FLOWS_SR1 4 /* excluding default flow */ +#define PRUETH_RX_FLOW_DATA_SR1 3 /* highest priority flow */ +#define PRUETH_MAX_RX_MGM_DESC_SR1 8 +#define PRUETH_MAX_RX_MGM_FLOWS_SR1 2 /* excluding default flow */ +#define PRUETH_RX_MGM_FLOW_RESPONSE_SR1 0 +#define PRUETH_RX_MGM_FLOW_TIMESTAMP_SR1 1 + +#define PRUETH_NUM_BUF_POOLS_SR1 16 +#define PRUETH_EMAC_BUF_POOL_START_SR1 8 +#define PRUETH_EMAC_BUF_POOL_MIN_SIZE_SR1 128 +#define PRUETH_EMAC_BUF_SIZE_SR1 1536 +#define PRUETH_EMAC_NUM_BUF_SR1 4 +#define PRUETH_EMAC_BUF_POOL_SIZE_SR1 (PRUETH_EMAC_NUM_BUF_SR1 * \ + PRUETH_EMAC_BUF_SIZE_SR1) +#define MSMC_RAM_SIZE_SR1 (SZ_64K + SZ_32K + SZ_2K) /* 0x1880 x 8 x 2 */ + +struct icssg_sr1_config { + __le32 status; /* Firmware status */ + __le32 addr_lo; /* MSMC Buffer pool base address low. */ + __le32 addr_hi; /* MSMC Buffer pool base address high. Must be 0 */ + __le32 tx_buf_sz[16]; /* Array of buffer pool sizes */ + __le32 num_tx_threads; /* Number of active egress threads, 1 to 4 */ + __le32 tx_rate_lim_en; /* Bitmask: Egress rate limit en per thread */ + __le32 rx_flow_id; /* RX flow id for first rx ring */ + __le32 rx_mgr_flow_id; /* RX flow id for the first management ring */ + __le32 flags; /* TBD */ + __le32 n_burst; /* for debug */ + __le32 rtu_status; /* RTU status */ + __le32 info; /* reserved */ + __le32 reserve; + __le32 rand_seed; /* Used for the random number generation at fw */ +} __packed; + +/* SR1.0 shutdown command to stop processing at firmware. + * Command format: 0x8101ss00, where + * - ss: sequence number. Currently not used by driver. + */ +#define ICSSG_SHUTDOWN_CMD_SR1 0x81010000 + +/* SR1.0 pstate speed/duplex command to set speed and duplex settings + * in firmware. + * Command format: 0x8102ssPN, where + * - ss: sequence number. Currently not used by driver. + * - P: port number (for switch mode). + * - N: Speed/Duplex state: + * 0x0 - 10Mbps/Half duplex; + * 0x8 - 10Mbps/Full duplex; + * 0x2 - 100Mbps/Half duplex; + * 0xa - 100Mbps/Full duplex; + * 0xc - 1Gbps/Full duplex; + * NOTE: The above are the same value as bits [3..1](slice 0) + * or bits [7..5](slice 1) of RGMII CFG register. + */ +#define ICSSG_PSTATE_SPEED_DUPLEX_CMD_SR1 0x81020000 + struct icssg_setclock_desc { u8 request; u8 restore; |