diff options
Diffstat (limited to '')
| -rw-r--r-- | drivers/net/phy/air_en8811h.c | 1090 |
1 files changed, 1090 insertions, 0 deletions
diff --git a/drivers/net/phy/air_en8811h.c b/drivers/net/phy/air_en8811h.c new file mode 100644 index 0000000000..3cdc8c6b30 --- /dev/null +++ b/drivers/net/phy/air_en8811h.c @@ -0,0 +1,1090 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Driver for the Airoha EN8811H 2.5 Gigabit PHY. + * + * Limitations of the EN8811H: + * - Only full duplex supported + * - Forced speed (AN off) is not supported by hardware (100Mbps) + * + * Source originated from airoha's en8811h.c and en8811h.h v1.2.1 + * + * Copyright (C) 2023 Airoha Technology Corp. + */ + +#include <linux/phy.h> +#include <linux/firmware.h> +#include <linux/property.h> +#include <linux/wordpart.h> +#include <asm/unaligned.h> + +#define EN8811H_PHY_ID 0x03a2a411 + +#define EN8811H_MD32_DM "airoha/EthMD32.dm.bin" +#define EN8811H_MD32_DSP "airoha/EthMD32.DSP.bin" + +#define AIR_FW_ADDR_DM 0x00000000 +#define AIR_FW_ADDR_DSP 0x00100000 + +/* MII Registers */ +#define AIR_AUX_CTRL_STATUS 0x1d +#define AIR_AUX_CTRL_STATUS_SPEED_MASK GENMASK(4, 2) +#define AIR_AUX_CTRL_STATUS_SPEED_100 0x4 +#define AIR_AUX_CTRL_STATUS_SPEED_1000 0x8 +#define AIR_AUX_CTRL_STATUS_SPEED_2500 0xc + +#define AIR_EXT_PAGE_ACCESS 0x1f +#define AIR_PHY_PAGE_STANDARD 0x0000 +#define AIR_PHY_PAGE_EXTENDED_4 0x0004 + +/* MII Registers Page 4*/ +#define AIR_BPBUS_MODE 0x10 +#define AIR_BPBUS_MODE_ADDR_FIXED 0x0000 +#define AIR_BPBUS_MODE_ADDR_INCR BIT(15) +#define AIR_BPBUS_WR_ADDR_HIGH 0x11 +#define AIR_BPBUS_WR_ADDR_LOW 0x12 +#define AIR_BPBUS_WR_DATA_HIGH 0x13 +#define AIR_BPBUS_WR_DATA_LOW 0x14 +#define AIR_BPBUS_RD_ADDR_HIGH 0x15 +#define AIR_BPBUS_RD_ADDR_LOW 0x16 +#define AIR_BPBUS_RD_DATA_HIGH 0x17 +#define AIR_BPBUS_RD_DATA_LOW 0x18 + +/* Registers on MDIO_MMD_VEND1 */ +#define EN8811H_PHY_FW_STATUS 0x8009 +#define EN8811H_PHY_READY 0x02 + +#define AIR_PHY_MCU_CMD_1 0x800c +#define AIR_PHY_MCU_CMD_1_MODE1 0x0 +#define AIR_PHY_MCU_CMD_2 0x800d +#define AIR_PHY_MCU_CMD_2_MODE1 0x0 +#define AIR_PHY_MCU_CMD_3 0x800e +#define AIR_PHY_MCU_CMD_3_MODE1 0x1101 +#define AIR_PHY_MCU_CMD_3_DOCMD 0x1100 +#define AIR_PHY_MCU_CMD_4 0x800f +#define AIR_PHY_MCU_CMD_4_MODE1 0x0002 +#define AIR_PHY_MCU_CMD_4_INTCLR 0x00e4 + +/* Registers on MDIO_MMD_VEND2 */ +#define AIR_PHY_LED_BCR 0x021 +#define AIR_PHY_LED_BCR_MODE_MASK GENMASK(1, 0) +#define AIR_PHY_LED_BCR_TIME_TEST BIT(2) +#define AIR_PHY_LED_BCR_CLK_EN BIT(3) +#define AIR_PHY_LED_BCR_EXT_CTRL BIT(15) + +#define AIR_PHY_LED_DUR_ON 0x022 + +#define AIR_PHY_LED_DUR_BLINK 0x023 + +#define AIR_PHY_LED_ON(i) (0x024 + ((i) * 2)) +#define AIR_PHY_LED_ON_MASK (GENMASK(6, 0) | BIT(8)) +#define AIR_PHY_LED_ON_LINK1000 BIT(0) +#define AIR_PHY_LED_ON_LINK100 BIT(1) +#define AIR_PHY_LED_ON_LINK10 BIT(2) +#define AIR_PHY_LED_ON_LINKDOWN BIT(3) +#define AIR_PHY_LED_ON_FDX BIT(4) /* Full duplex */ +#define AIR_PHY_LED_ON_HDX BIT(5) /* Half duplex */ +#define AIR_PHY_LED_ON_FORCE_ON BIT(6) +#define AIR_PHY_LED_ON_LINK2500 BIT(8) +#define AIR_PHY_LED_ON_POLARITY BIT(14) +#define AIR_PHY_LED_ON_ENABLE BIT(15) + +#define AIR_PHY_LED_BLINK(i) (0x025 + ((i) * 2)) +#define AIR_PHY_LED_BLINK_1000TX BIT(0) +#define AIR_PHY_LED_BLINK_1000RX BIT(1) +#define AIR_PHY_LED_BLINK_100TX BIT(2) +#define AIR_PHY_LED_BLINK_100RX BIT(3) +#define AIR_PHY_LED_BLINK_10TX BIT(4) +#define AIR_PHY_LED_BLINK_10RX BIT(5) +#define AIR_PHY_LED_BLINK_COLLISION BIT(6) +#define AIR_PHY_LED_BLINK_RX_CRC_ERR BIT(7) +#define AIR_PHY_LED_BLINK_RX_IDLE_ERR BIT(8) +#define AIR_PHY_LED_BLINK_FORCE_BLINK BIT(9) +#define AIR_PHY_LED_BLINK_2500TX BIT(10) +#define AIR_PHY_LED_BLINK_2500RX BIT(11) + +/* Registers on BUCKPBUS */ +#define EN8811H_2P5G_LPA 0x3b30 +#define EN8811H_2P5G_LPA_2P5G BIT(0) + +#define EN8811H_FW_VERSION 0x3b3c + +#define EN8811H_POLARITY 0xca0f8 +#define EN8811H_POLARITY_TX_NORMAL BIT(0) +#define EN8811H_POLARITY_RX_REVERSE BIT(1) + +#define EN8811H_GPIO_OUTPUT 0xcf8b8 +#define EN8811H_GPIO_OUTPUT_345 (BIT(3) | BIT(4) | BIT(5)) + +#define EN8811H_FW_CTRL_1 0x0f0018 +#define EN8811H_FW_CTRL_1_START 0x0 +#define EN8811H_FW_CTRL_1_FINISH 0x1 +#define EN8811H_FW_CTRL_2 0x800000 +#define EN8811H_FW_CTRL_2_LOADING BIT(11) + +/* Led definitions */ +#define EN8811H_LED_COUNT 3 + +/* Default LED setup: + * GPIO5 <-> LED0 On: Link detected, blink Rx/Tx + * GPIO4 <-> LED1 On: Link detected at 2500 or 1000 Mbps + * GPIO3 <-> LED2 On: Link detected at 2500 or 100 Mbps + */ +#define AIR_DEFAULT_TRIGGER_LED0 (BIT(TRIGGER_NETDEV_LINK) | \ + BIT(TRIGGER_NETDEV_RX) | \ + BIT(TRIGGER_NETDEV_TX)) +#define AIR_DEFAULT_TRIGGER_LED1 (BIT(TRIGGER_NETDEV_LINK_2500) | \ + BIT(TRIGGER_NETDEV_LINK_1000)) +#define AIR_DEFAULT_TRIGGER_LED2 (BIT(TRIGGER_NETDEV_LINK_2500) | \ + BIT(TRIGGER_NETDEV_LINK_100)) + +struct led { + unsigned long rules; + unsigned long state; +}; + +struct en8811h_priv { + u32 firmware_version; + bool mcu_needs_restart; + struct led led[EN8811H_LED_COUNT]; +}; + +enum { + AIR_PHY_LED_STATE_FORCE_ON, + AIR_PHY_LED_STATE_FORCE_BLINK, +}; + +enum { + AIR_PHY_LED_DUR_BLINK_32MS, + AIR_PHY_LED_DUR_BLINK_64MS, + AIR_PHY_LED_DUR_BLINK_128MS, + AIR_PHY_LED_DUR_BLINK_256MS, + AIR_PHY_LED_DUR_BLINK_512MS, + AIR_PHY_LED_DUR_BLINK_1024MS, +}; + +enum { + AIR_LED_DISABLE, + AIR_LED_ENABLE, +}; + +enum { + AIR_ACTIVE_LOW, + AIR_ACTIVE_HIGH, +}; + +enum { + AIR_LED_MODE_DISABLE, + AIR_LED_MODE_USER_DEFINE, +}; + +#define AIR_PHY_LED_DUR_UNIT 1024 +#define AIR_PHY_LED_DUR (AIR_PHY_LED_DUR_UNIT << AIR_PHY_LED_DUR_BLINK_64MS) + +static const unsigned long en8811h_led_trig = BIT(TRIGGER_NETDEV_FULL_DUPLEX) | + BIT(TRIGGER_NETDEV_LINK) | + BIT(TRIGGER_NETDEV_LINK_10) | + BIT(TRIGGER_NETDEV_LINK_100) | + BIT(TRIGGER_NETDEV_LINK_1000) | + BIT(TRIGGER_NETDEV_LINK_2500) | + BIT(TRIGGER_NETDEV_RX) | + BIT(TRIGGER_NETDEV_TX); + +static int air_phy_read_page(struct phy_device *phydev) +{ + return __phy_read(phydev, AIR_EXT_PAGE_ACCESS); +} + +static int air_phy_write_page(struct phy_device *phydev, int page) +{ + return __phy_write(phydev, AIR_EXT_PAGE_ACCESS, page); +} + +static int __air_buckpbus_reg_write(struct phy_device *phydev, + u32 pbus_address, u32 pbus_data) +{ + int ret; + + ret = __phy_write(phydev, AIR_BPBUS_MODE, AIR_BPBUS_MODE_ADDR_FIXED); + if (ret < 0) + return ret; + + ret = __phy_write(phydev, AIR_BPBUS_WR_ADDR_HIGH, + upper_16_bits(pbus_address)); + if (ret < 0) + return ret; + + ret = __phy_write(phydev, AIR_BPBUS_WR_ADDR_LOW, + lower_16_bits(pbus_address)); + if (ret < 0) + return ret; + + ret = __phy_write(phydev, AIR_BPBUS_WR_DATA_HIGH, + upper_16_bits(pbus_data)); + if (ret < 0) + return ret; + + ret = __phy_write(phydev, AIR_BPBUS_WR_DATA_LOW, + lower_16_bits(pbus_data)); + if (ret < 0) + return ret; + + return 0; +} + +static int air_buckpbus_reg_write(struct phy_device *phydev, + u32 pbus_address, u32 pbus_data) +{ + int saved_page; + int ret = 0; + + saved_page = phy_select_page(phydev, AIR_PHY_PAGE_EXTENDED_4); + + if (saved_page >= 0) { + ret = __air_buckpbus_reg_write(phydev, pbus_address, + pbus_data); + if (ret < 0) + phydev_err(phydev, "%s 0x%08x failed: %d\n", __func__, + pbus_address, ret); + } + + return phy_restore_page(phydev, saved_page, ret); +} + +static int __air_buckpbus_reg_read(struct phy_device *phydev, + u32 pbus_address, u32 *pbus_data) +{ + int pbus_data_low, pbus_data_high; + int ret; + + ret = __phy_write(phydev, AIR_BPBUS_MODE, AIR_BPBUS_MODE_ADDR_FIXED); + if (ret < 0) + return ret; + + ret = __phy_write(phydev, AIR_BPBUS_RD_ADDR_HIGH, + upper_16_bits(pbus_address)); + if (ret < 0) + return ret; + + ret = __phy_write(phydev, AIR_BPBUS_RD_ADDR_LOW, + lower_16_bits(pbus_address)); + if (ret < 0) + return ret; + + pbus_data_high = __phy_read(phydev, AIR_BPBUS_RD_DATA_HIGH); + if (pbus_data_high < 0) + return pbus_data_high; + + pbus_data_low = __phy_read(phydev, AIR_BPBUS_RD_DATA_LOW); + if (pbus_data_low < 0) + return pbus_data_low; + + *pbus_data = pbus_data_low | (pbus_data_high << 16); + return 0; +} + +static int air_buckpbus_reg_read(struct phy_device *phydev, + u32 pbus_address, u32 *pbus_data) +{ + int saved_page; + int ret = 0; + + saved_page = phy_select_page(phydev, AIR_PHY_PAGE_EXTENDED_4); + + if (saved_page >= 0) { + ret = __air_buckpbus_reg_read(phydev, pbus_address, pbus_data); + if (ret < 0) + phydev_err(phydev, "%s 0x%08x failed: %d\n", __func__, + pbus_address, ret); + } + + return phy_restore_page(phydev, saved_page, ret); +} + +static int __air_buckpbus_reg_modify(struct phy_device *phydev, + u32 pbus_address, u32 mask, u32 set) +{ + int pbus_data_low, pbus_data_high; + u32 pbus_data_old, pbus_data_new; + int ret; + + ret = __phy_write(phydev, AIR_BPBUS_MODE, AIR_BPBUS_MODE_ADDR_FIXED); + if (ret < 0) + return ret; + + ret = __phy_write(phydev, AIR_BPBUS_RD_ADDR_HIGH, + upper_16_bits(pbus_address)); + if (ret < 0) + return ret; + + ret = __phy_write(phydev, AIR_BPBUS_RD_ADDR_LOW, + lower_16_bits(pbus_address)); + if (ret < 0) + return ret; + + pbus_data_high = __phy_read(phydev, AIR_BPBUS_RD_DATA_HIGH); + if (pbus_data_high < 0) + return pbus_data_high; + + pbus_data_low = __phy_read(phydev, AIR_BPBUS_RD_DATA_LOW); + if (pbus_data_low < 0) + return pbus_data_low; + + pbus_data_old = pbus_data_low | (pbus_data_high << 16); + pbus_data_new = (pbus_data_old & ~mask) | set; + if (pbus_data_new == pbus_data_old) + return 0; + + ret = __phy_write(phydev, AIR_BPBUS_WR_ADDR_HIGH, + upper_16_bits(pbus_address)); + if (ret < 0) + return ret; + + ret = __phy_write(phydev, AIR_BPBUS_WR_ADDR_LOW, + lower_16_bits(pbus_address)); + if (ret < 0) + return ret; + + ret = __phy_write(phydev, AIR_BPBUS_WR_DATA_HIGH, + upper_16_bits(pbus_data_new)); + if (ret < 0) + return ret; + + ret = __phy_write(phydev, AIR_BPBUS_WR_DATA_LOW, + lower_16_bits(pbus_data_new)); + if (ret < 0) + return ret; + + return 0; +} + +static int air_buckpbus_reg_modify(struct phy_device *phydev, + u32 pbus_address, u32 mask, u32 set) +{ + int saved_page; + int ret = 0; + + saved_page = phy_select_page(phydev, AIR_PHY_PAGE_EXTENDED_4); + + if (saved_page >= 0) { + ret = __air_buckpbus_reg_modify(phydev, pbus_address, mask, + set); + if (ret < 0) + phydev_err(phydev, "%s 0x%08x failed: %d\n", __func__, + pbus_address, ret); + } + + return phy_restore_page(phydev, saved_page, ret); +} + +static int __air_write_buf(struct phy_device *phydev, u32 address, + const struct firmware *fw) +{ + unsigned int offset; + int ret; + u16 val; + + ret = __phy_write(phydev, AIR_BPBUS_MODE, AIR_BPBUS_MODE_ADDR_INCR); + if (ret < 0) + return ret; + + ret = __phy_write(phydev, AIR_BPBUS_WR_ADDR_HIGH, + upper_16_bits(address)); + if (ret < 0) + return ret; + + ret = __phy_write(phydev, AIR_BPBUS_WR_ADDR_LOW, + lower_16_bits(address)); + if (ret < 0) + return ret; + + for (offset = 0; offset < fw->size; offset += 4) { + val = get_unaligned_le16(&fw->data[offset + 2]); + ret = __phy_write(phydev, AIR_BPBUS_WR_DATA_HIGH, val); + if (ret < 0) + return ret; + + val = get_unaligned_le16(&fw->data[offset]); + ret = __phy_write(phydev, AIR_BPBUS_WR_DATA_LOW, val); + if (ret < 0) + return ret; + } + + return 0; +} + +static int air_write_buf(struct phy_device *phydev, u32 address, + const struct firmware *fw) +{ + int saved_page; + int ret = 0; + + saved_page = phy_select_page(phydev, AIR_PHY_PAGE_EXTENDED_4); + + if (saved_page >= 0) { + ret = __air_write_buf(phydev, address, fw); + if (ret < 0) + phydev_err(phydev, "%s 0x%08x failed: %d\n", __func__, + address, ret); + } + + return phy_restore_page(phydev, saved_page, ret); +} + +static int en8811h_wait_mcu_ready(struct phy_device *phydev) +{ + int ret, reg_value; + + /* Because of mdio-lock, may have to wait for multiple loads */ + ret = phy_read_mmd_poll_timeout(phydev, MDIO_MMD_VEND1, + EN8811H_PHY_FW_STATUS, reg_value, + reg_value == EN8811H_PHY_READY, + 20000, 7500000, true); + if (ret) { + phydev_err(phydev, "MCU not ready: 0x%x\n", reg_value); + return -ENODEV; + } + + return 0; +} + +static int en8811h_load_firmware(struct phy_device *phydev) +{ + struct en8811h_priv *priv = phydev->priv; + struct device *dev = &phydev->mdio.dev; + const struct firmware *fw1, *fw2; + int ret; + + ret = request_firmware_direct(&fw1, EN8811H_MD32_DM, dev); + if (ret < 0) + return ret; + + ret = request_firmware_direct(&fw2, EN8811H_MD32_DSP, dev); + if (ret < 0) + goto en8811h_load_firmware_rel1; + + ret = air_buckpbus_reg_write(phydev, EN8811H_FW_CTRL_1, + EN8811H_FW_CTRL_1_START); + if (ret < 0) + goto en8811h_load_firmware_out; + + ret = air_buckpbus_reg_modify(phydev, EN8811H_FW_CTRL_2, + EN8811H_FW_CTRL_2_LOADING, + EN8811H_FW_CTRL_2_LOADING); + if (ret < 0) + goto en8811h_load_firmware_out; + + ret = air_write_buf(phydev, AIR_FW_ADDR_DM, fw1); + if (ret < 0) + goto en8811h_load_firmware_out; + + ret = air_write_buf(phydev, AIR_FW_ADDR_DSP, fw2); + if (ret < 0) + goto en8811h_load_firmware_out; + + ret = air_buckpbus_reg_modify(phydev, EN8811H_FW_CTRL_2, + EN8811H_FW_CTRL_2_LOADING, 0); + if (ret < 0) + goto en8811h_load_firmware_out; + + ret = air_buckpbus_reg_write(phydev, EN8811H_FW_CTRL_1, + EN8811H_FW_CTRL_1_FINISH); + if (ret < 0) + goto en8811h_load_firmware_out; + + ret = en8811h_wait_mcu_ready(phydev); + + air_buckpbus_reg_read(phydev, EN8811H_FW_VERSION, + &priv->firmware_version); + phydev_info(phydev, "MD32 firmware version: %08x\n", + priv->firmware_version); + +en8811h_load_firmware_out: + release_firmware(fw2); + +en8811h_load_firmware_rel1: + release_firmware(fw1); + + if (ret < 0) + phydev_err(phydev, "Load firmware failed: %d\n", ret); + + return ret; +} + +static int en8811h_restart_mcu(struct phy_device *phydev) +{ + int ret; + + ret = air_buckpbus_reg_write(phydev, EN8811H_FW_CTRL_1, + EN8811H_FW_CTRL_1_START); + if (ret < 0) + return ret; + + ret = air_buckpbus_reg_write(phydev, EN8811H_FW_CTRL_1, + EN8811H_FW_CTRL_1_FINISH); + if (ret < 0) + return ret; + + return en8811h_wait_mcu_ready(phydev); +} + +static int air_hw_led_on_set(struct phy_device *phydev, u8 index, bool on) +{ + struct en8811h_priv *priv = phydev->priv; + bool changed; + + if (index >= EN8811H_LED_COUNT) + return -EINVAL; + + if (on) + changed = !test_and_set_bit(AIR_PHY_LED_STATE_FORCE_ON, + &priv->led[index].state); + else + changed = !!test_and_clear_bit(AIR_PHY_LED_STATE_FORCE_ON, + &priv->led[index].state); + + changed |= (priv->led[index].rules != 0); + + /* clear netdev trigger rules in case LED_OFF has been set */ + if (!on) + priv->led[index].rules = 0; + + if (changed) + return phy_modify_mmd(phydev, MDIO_MMD_VEND2, + AIR_PHY_LED_ON(index), + AIR_PHY_LED_ON_MASK, + on ? AIR_PHY_LED_ON_FORCE_ON : 0); + + return 0; +} + +static int air_hw_led_blink_set(struct phy_device *phydev, u8 index, + bool blinking) +{ + struct en8811h_priv *priv = phydev->priv; + bool changed; + + if (index >= EN8811H_LED_COUNT) + return -EINVAL; + + if (blinking) + changed = !test_and_set_bit(AIR_PHY_LED_STATE_FORCE_BLINK, + &priv->led[index].state); + else + changed = !!test_and_clear_bit(AIR_PHY_LED_STATE_FORCE_BLINK, + &priv->led[index].state); + + changed |= (priv->led[index].rules != 0); + + if (changed) + return phy_write_mmd(phydev, MDIO_MMD_VEND2, + AIR_PHY_LED_BLINK(index), + blinking ? + AIR_PHY_LED_BLINK_FORCE_BLINK : 0); + else + return 0; +} + +static int air_led_blink_set(struct phy_device *phydev, u8 index, + unsigned long *delay_on, + unsigned long *delay_off) +{ + struct en8811h_priv *priv = phydev->priv; + bool blinking = false; + int err; + + if (index >= EN8811H_LED_COUNT) + return -EINVAL; + + if (delay_on && delay_off && (*delay_on > 0) && (*delay_off > 0)) { + blinking = true; + *delay_on = 50; + *delay_off = 50; + } + + err = air_hw_led_blink_set(phydev, index, blinking); + if (err) + return err; + + /* led-blink set, so switch led-on off */ + err = air_hw_led_on_set(phydev, index, false); + if (err) + return err; + + /* hw-control is off*/ + if (!!test_bit(AIR_PHY_LED_STATE_FORCE_BLINK, &priv->led[index].state)) + priv->led[index].rules = 0; + + return 0; +} + +static int air_led_brightness_set(struct phy_device *phydev, u8 index, + enum led_brightness value) +{ + struct en8811h_priv *priv = phydev->priv; + int err; + + if (index >= EN8811H_LED_COUNT) + return -EINVAL; + + /* led-on set, so switch led-blink off */ + err = air_hw_led_blink_set(phydev, index, false); + if (err) + return err; + + err = air_hw_led_on_set(phydev, index, (value != LED_OFF)); + if (err) + return err; + + /* hw-control is off */ + if (!!test_bit(AIR_PHY_LED_STATE_FORCE_ON, &priv->led[index].state)) + priv->led[index].rules = 0; + + return 0; +} + +static int air_led_hw_control_get(struct phy_device *phydev, u8 index, + unsigned long *rules) +{ + struct en8811h_priv *priv = phydev->priv; + + if (index >= EN8811H_LED_COUNT) + return -EINVAL; + + *rules = priv->led[index].rules; + + return 0; +}; + +static int air_led_hw_control_set(struct phy_device *phydev, u8 index, + unsigned long rules) +{ + struct en8811h_priv *priv = phydev->priv; + u16 on = 0, blink = 0; + int ret; + + if (index >= EN8811H_LED_COUNT) + return -EINVAL; + + priv->led[index].rules = rules; + + if (rules & BIT(TRIGGER_NETDEV_FULL_DUPLEX)) + on |= AIR_PHY_LED_ON_FDX; + + if (rules & (BIT(TRIGGER_NETDEV_LINK_10) | BIT(TRIGGER_NETDEV_LINK))) + on |= AIR_PHY_LED_ON_LINK10; + + if (rules & (BIT(TRIGGER_NETDEV_LINK_100) | BIT(TRIGGER_NETDEV_LINK))) + on |= AIR_PHY_LED_ON_LINK100; + + if (rules & (BIT(TRIGGER_NETDEV_LINK_1000) | BIT(TRIGGER_NETDEV_LINK))) + on |= AIR_PHY_LED_ON_LINK1000; + + if (rules & (BIT(TRIGGER_NETDEV_LINK_2500) | BIT(TRIGGER_NETDEV_LINK))) + on |= AIR_PHY_LED_ON_LINK2500; + + if (rules & BIT(TRIGGER_NETDEV_RX)) { + blink |= AIR_PHY_LED_BLINK_10RX | + AIR_PHY_LED_BLINK_100RX | + AIR_PHY_LED_BLINK_1000RX | + AIR_PHY_LED_BLINK_2500RX; + } + + if (rules & BIT(TRIGGER_NETDEV_TX)) { + blink |= AIR_PHY_LED_BLINK_10TX | + AIR_PHY_LED_BLINK_100TX | + AIR_PHY_LED_BLINK_1000TX | + AIR_PHY_LED_BLINK_2500TX; + } + + if (blink || on) { + /* switch hw-control on, so led-on and led-blink are off */ + clear_bit(AIR_PHY_LED_STATE_FORCE_ON, + &priv->led[index].state); + clear_bit(AIR_PHY_LED_STATE_FORCE_BLINK, + &priv->led[index].state); + } else { + priv->led[index].rules = 0; + } + + ret = phy_modify_mmd(phydev, MDIO_MMD_VEND2, AIR_PHY_LED_ON(index), + AIR_PHY_LED_ON_MASK, on); + + if (ret < 0) + return ret; + + return phy_write_mmd(phydev, MDIO_MMD_VEND2, AIR_PHY_LED_BLINK(index), + blink); +}; + +static int air_led_init(struct phy_device *phydev, u8 index, u8 state, u8 pol) +{ + int val = 0; + int err; + + if (index >= EN8811H_LED_COUNT) + return -EINVAL; + + if (state == AIR_LED_ENABLE) + val |= AIR_PHY_LED_ON_ENABLE; + else + val &= ~AIR_PHY_LED_ON_ENABLE; + + if (pol == AIR_ACTIVE_HIGH) + val |= AIR_PHY_LED_ON_POLARITY; + else + val &= ~AIR_PHY_LED_ON_POLARITY; + + err = phy_modify_mmd(phydev, MDIO_MMD_VEND2, AIR_PHY_LED_ON(index), + AIR_PHY_LED_ON_ENABLE | + AIR_PHY_LED_ON_POLARITY, val); + + if (err < 0) + return err; + + return 0; +} + +static int air_leds_init(struct phy_device *phydev, int num, int dur, int mode) +{ + struct en8811h_priv *priv = phydev->priv; + int ret, i; + + ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, AIR_PHY_LED_DUR_BLINK, + dur); + if (ret < 0) + return ret; + + ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, AIR_PHY_LED_DUR_ON, + dur >> 1); + if (ret < 0) + return ret; + + switch (mode) { + case AIR_LED_MODE_DISABLE: + ret = phy_modify_mmd(phydev, MDIO_MMD_VEND2, AIR_PHY_LED_BCR, + AIR_PHY_LED_BCR_EXT_CTRL | + AIR_PHY_LED_BCR_MODE_MASK, 0); + if (ret < 0) + return ret; + break; + case AIR_LED_MODE_USER_DEFINE: + ret = phy_modify_mmd(phydev, MDIO_MMD_VEND2, AIR_PHY_LED_BCR, + AIR_PHY_LED_BCR_EXT_CTRL | + AIR_PHY_LED_BCR_CLK_EN, + AIR_PHY_LED_BCR_EXT_CTRL | + AIR_PHY_LED_BCR_CLK_EN); + if (ret < 0) + return ret; + break; + default: + phydev_err(phydev, "LED mode %d is not supported\n", mode); + return -EINVAL; + } + + for (i = 0; i < num; ++i) { + ret = air_led_init(phydev, i, AIR_LED_ENABLE, AIR_ACTIVE_HIGH); + if (ret < 0) { + phydev_err(phydev, "LED%d init failed: %d\n", i, ret); + return ret; + } + air_led_hw_control_set(phydev, i, priv->led[i].rules); + } + + return 0; +} + +static int en8811h_led_hw_is_supported(struct phy_device *phydev, u8 index, + unsigned long rules) +{ + if (index >= EN8811H_LED_COUNT) + return -EINVAL; + + /* All combinations of the supported triggers are allowed */ + if (rules & ~en8811h_led_trig) + return -EOPNOTSUPP; + + return 0; +}; + +static int en8811h_probe(struct phy_device *phydev) +{ + struct en8811h_priv *priv; + int ret; + + priv = devm_kzalloc(&phydev->mdio.dev, sizeof(struct en8811h_priv), + GFP_KERNEL); + if (!priv) + return -ENOMEM; + phydev->priv = priv; + + ret = en8811h_load_firmware(phydev); + if (ret < 0) + return ret; + + /* mcu has just restarted after firmware load */ + priv->mcu_needs_restart = false; + + priv->led[0].rules = AIR_DEFAULT_TRIGGER_LED0; + priv->led[1].rules = AIR_DEFAULT_TRIGGER_LED1; + priv->led[2].rules = AIR_DEFAULT_TRIGGER_LED2; + + /* MDIO_DEVS1/2 empty, so set mmds_present bits here */ + phydev->c45_ids.mmds_present |= MDIO_DEVS_PMAPMD | MDIO_DEVS_AN; + + ret = air_leds_init(phydev, EN8811H_LED_COUNT, AIR_PHY_LED_DUR, + AIR_LED_MODE_DISABLE); + if (ret < 0) { + phydev_err(phydev, "Failed to disable leds: %d\n", ret); + return ret; + } + + /* Configure led gpio pins as output */ + ret = air_buckpbus_reg_modify(phydev, EN8811H_GPIO_OUTPUT, + EN8811H_GPIO_OUTPUT_345, + EN8811H_GPIO_OUTPUT_345); + if (ret < 0) + return ret; + + return 0; +} + +static int en8811h_config_init(struct phy_device *phydev) +{ + struct en8811h_priv *priv = phydev->priv; + struct device *dev = &phydev->mdio.dev; + u32 pbus_value; + int ret; + + /* If restart happened in .probe(), no need to restart now */ + if (priv->mcu_needs_restart) { + ret = en8811h_restart_mcu(phydev); + if (ret < 0) + return ret; + } else { + /* Next calls to .config_init() mcu needs to restart */ + priv->mcu_needs_restart = true; + } + + /* Select mode 1, the only mode supported. + * Configures the SerDes for 2500Base-X with rate adaptation + */ + ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, AIR_PHY_MCU_CMD_1, + AIR_PHY_MCU_CMD_1_MODE1); + if (ret < 0) + return ret; + ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, AIR_PHY_MCU_CMD_2, + AIR_PHY_MCU_CMD_2_MODE1); + if (ret < 0) + return ret; + ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, AIR_PHY_MCU_CMD_3, + AIR_PHY_MCU_CMD_3_MODE1); + if (ret < 0) + return ret; + ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, AIR_PHY_MCU_CMD_4, + AIR_PHY_MCU_CMD_4_MODE1); + if (ret < 0) + return ret; + + /* Serdes polarity */ + pbus_value = 0; + if (device_property_read_bool(dev, "airoha,pnswap-rx")) + pbus_value |= EN8811H_POLARITY_RX_REVERSE; + else + pbus_value &= ~EN8811H_POLARITY_RX_REVERSE; + if (device_property_read_bool(dev, "airoha,pnswap-tx")) + pbus_value &= ~EN8811H_POLARITY_TX_NORMAL; + else + pbus_value |= EN8811H_POLARITY_TX_NORMAL; + ret = air_buckpbus_reg_modify(phydev, EN8811H_POLARITY, + EN8811H_POLARITY_RX_REVERSE | + EN8811H_POLARITY_TX_NORMAL, pbus_value); + if (ret < 0) + return ret; + + ret = air_leds_init(phydev, EN8811H_LED_COUNT, AIR_PHY_LED_DUR, + AIR_LED_MODE_USER_DEFINE); + if (ret < 0) { + phydev_err(phydev, "Failed to initialize leds: %d\n", ret); + return ret; + } + + return 0; +} + +static int en8811h_get_features(struct phy_device *phydev) +{ + linkmode_set_bit_array(phy_basic_ports_array, + ARRAY_SIZE(phy_basic_ports_array), + phydev->supported); + + return genphy_c45_pma_read_abilities(phydev); +} + +static int en8811h_get_rate_matching(struct phy_device *phydev, + phy_interface_t iface) +{ + return RATE_MATCH_PAUSE; +} + +static int en8811h_config_aneg(struct phy_device *phydev) +{ + bool changed = false; + int ret; + u32 adv; + + if (phydev->autoneg == AUTONEG_DISABLE) { + phydev_warn(phydev, "Disabling autoneg is not supported\n"); + return -EINVAL; + } + + adv = linkmode_adv_to_mii_10gbt_adv_t(phydev->advertising); + + ret = phy_modify_mmd_changed(phydev, MDIO_MMD_AN, MDIO_AN_10GBT_CTRL, + MDIO_AN_10GBT_CTRL_ADV2_5G, adv); + if (ret < 0) + return ret; + if (ret > 0) + changed = true; + + return __genphy_config_aneg(phydev, changed); +} + +static int en8811h_read_status(struct phy_device *phydev) +{ + struct en8811h_priv *priv = phydev->priv; + u32 pbus_value; + int ret, val; + + ret = genphy_update_link(phydev); + if (ret) + return ret; + + phydev->master_slave_get = MASTER_SLAVE_CFG_UNSUPPORTED; + phydev->master_slave_state = MASTER_SLAVE_STATE_UNSUPPORTED; + phydev->speed = SPEED_UNKNOWN; + phydev->duplex = DUPLEX_UNKNOWN; + phydev->pause = 0; + phydev->asym_pause = 0; + phydev->rate_matching = RATE_MATCH_PAUSE; + + ret = genphy_read_master_slave(phydev); + if (ret < 0) + return ret; + + ret = genphy_read_lpa(phydev); + if (ret < 0) + return ret; + + /* Get link partner 2.5GBASE-T ability from vendor register */ + ret = air_buckpbus_reg_read(phydev, EN8811H_2P5G_LPA, &pbus_value); + if (ret < 0) + return ret; + linkmode_mod_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, + phydev->lp_advertising, + pbus_value & EN8811H_2P5G_LPA_2P5G); + + if (phydev->autoneg_complete) + phy_resolve_aneg_pause(phydev); + + if (!phydev->link) + return 0; + + /* Get real speed from vendor register */ + val = phy_read(phydev, AIR_AUX_CTRL_STATUS); + if (val < 0) + return val; + switch (val & AIR_AUX_CTRL_STATUS_SPEED_MASK) { + case AIR_AUX_CTRL_STATUS_SPEED_2500: + phydev->speed = SPEED_2500; + break; + case AIR_AUX_CTRL_STATUS_SPEED_1000: + phydev->speed = SPEED_1000; + break; + case AIR_AUX_CTRL_STATUS_SPEED_100: + phydev->speed = SPEED_100; + break; + } + + /* Firmware before version 24011202 has no vendor register 2P5G_LPA. + * Assume link partner advertised it if connected at 2500Mbps. + */ + if (priv->firmware_version < 0x24011202) { + linkmode_mod_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, + phydev->lp_advertising, + phydev->speed == SPEED_2500); + } + + /* Only supports full duplex */ + phydev->duplex = DUPLEX_FULL; + + return 0; +} + +static int en8811h_clear_intr(struct phy_device *phydev) +{ + int ret; + + ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, AIR_PHY_MCU_CMD_3, + AIR_PHY_MCU_CMD_3_DOCMD); + if (ret < 0) + return ret; + + ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, AIR_PHY_MCU_CMD_4, + AIR_PHY_MCU_CMD_4_INTCLR); + if (ret < 0) + return ret; + + return 0; +} + +static irqreturn_t en8811h_handle_interrupt(struct phy_device *phydev) +{ + int ret; + + ret = en8811h_clear_intr(phydev); + if (ret < 0) { + phy_error(phydev); + return IRQ_NONE; + } + + phy_trigger_machine(phydev); + + return IRQ_HANDLED; +} + +static struct phy_driver en8811h_driver[] = { +{ + PHY_ID_MATCH_MODEL(EN8811H_PHY_ID), + .name = "Airoha EN8811H", + .probe = en8811h_probe, + .get_features = en8811h_get_features, + .config_init = en8811h_config_init, + .get_rate_matching = en8811h_get_rate_matching, + .config_aneg = en8811h_config_aneg, + .read_status = en8811h_read_status, + .config_intr = en8811h_clear_intr, + .handle_interrupt = en8811h_handle_interrupt, + .led_hw_is_supported = en8811h_led_hw_is_supported, + .read_page = air_phy_read_page, + .write_page = air_phy_write_page, + .led_blink_set = air_led_blink_set, + .led_brightness_set = air_led_brightness_set, + .led_hw_control_set = air_led_hw_control_set, + .led_hw_control_get = air_led_hw_control_get, +} }; + +module_phy_driver(en8811h_driver); + +static struct mdio_device_id __maybe_unused en8811h_tbl[] = { + { PHY_ID_MATCH_MODEL(EN8811H_PHY_ID) }, + { } +}; + +MODULE_DEVICE_TABLE(mdio, en8811h_tbl); +MODULE_FIRMWARE(EN8811H_MD32_DM); +MODULE_FIRMWARE(EN8811H_MD32_DSP); + +MODULE_DESCRIPTION("Airoha EN8811H PHY drivers"); +MODULE_AUTHOR("Airoha"); +MODULE_AUTHOR("Eric Woudstra <ericwouds@gmail.com>"); +MODULE_LICENSE("GPL"); |