diff options
Diffstat (limited to 'drivers/net/phy/microchip_t1s.c')
| -rw-r--r-- | drivers/net/phy/microchip_t1s.c | 306 |
1 files changed, 306 insertions, 0 deletions
diff --git a/drivers/net/phy/microchip_t1s.c b/drivers/net/phy/microchip_t1s.c new file mode 100644 index 0000000000..534ca7d1b0 --- /dev/null +++ b/drivers/net/phy/microchip_t1s.c @@ -0,0 +1,306 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Driver for Microchip 10BASE-T1S PHYs + * + * Support: Microchip Phys: + * lan8670/1/2 Rev.B1 + * lan8650/1 Rev.B0 Internal PHYs + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/phy.h> + +#define PHY_ID_LAN867X_REVB1 0x0007C162 +#define PHY_ID_LAN865X_REVB0 0x0007C1B3 + +#define LAN867X_REG_STS2 0x0019 + +#define LAN867x_RESET_COMPLETE_STS BIT(11) + +#define LAN865X_REG_CFGPARAM_ADDR 0x00D8 +#define LAN865X_REG_CFGPARAM_DATA 0x00D9 +#define LAN865X_REG_CFGPARAM_CTRL 0x00DA +#define LAN865X_REG_STS2 0x0019 + +#define LAN865X_CFGPARAM_READ_ENABLE BIT(1) + +/* The arrays below are pulled from the following table from AN1699 + * Access MMD Address Value Mask + * RMW 0x1F 0x00D0 0x0002 0x0E03 + * RMW 0x1F 0x00D1 0x0000 0x0300 + * RMW 0x1F 0x0084 0x3380 0xFFC0 + * RMW 0x1F 0x0085 0x0006 0x000F + * RMW 0x1F 0x008A 0xC000 0xF800 + * RMW 0x1F 0x0087 0x801C 0x801C + * RMW 0x1F 0x0088 0x033F 0x1FFF + * W 0x1F 0x008B 0x0404 ------ + * RMW 0x1F 0x0080 0x0600 0x0600 + * RMW 0x1F 0x00F1 0x2400 0x7F00 + * RMW 0x1F 0x0096 0x2000 0x2000 + * W 0x1F 0x0099 0x7F80 ------ + */ + +static const u32 lan867x_revb1_fixup_registers[12] = { + 0x00D0, 0x00D1, 0x0084, 0x0085, + 0x008A, 0x0087, 0x0088, 0x008B, + 0x0080, 0x00F1, 0x0096, 0x0099, +}; + +static const u16 lan867x_revb1_fixup_values[12] = { + 0x0002, 0x0000, 0x3380, 0x0006, + 0xC000, 0x801C, 0x033F, 0x0404, + 0x0600, 0x2400, 0x2000, 0x7F80, +}; + +static const u16 lan867x_revb1_fixup_masks[12] = { + 0x0E03, 0x0300, 0xFFC0, 0x000F, + 0xF800, 0x801C, 0x1FFF, 0xFFFF, + 0x0600, 0x7F00, 0x2000, 0xFFFF, +}; + +/* LAN865x Rev.B0 configuration parameters from AN1760 */ +static const u32 lan865x_revb0_fixup_registers[28] = { + 0x0091, 0x0081, 0x0043, 0x0044, + 0x0045, 0x0053, 0x0054, 0x0055, + 0x0040, 0x0050, 0x00D0, 0x00E9, + 0x00F5, 0x00F4, 0x00F8, 0x00F9, + 0x00B0, 0x00B1, 0x00B2, 0x00B3, + 0x00B4, 0x00B5, 0x00B6, 0x00B7, + 0x00B8, 0x00B9, 0x00BA, 0x00BB, +}; + +static const u16 lan865x_revb0_fixup_values[28] = { + 0x9660, 0x00C0, 0x00FF, 0xFFFF, + 0x0000, 0x00FF, 0xFFFF, 0x0000, + 0x0002, 0x0002, 0x5F21, 0x9E50, + 0x1CF8, 0xC020, 0x9B00, 0x4E53, + 0x0103, 0x0910, 0x1D26, 0x002A, + 0x0103, 0x070D, 0x1720, 0x0027, + 0x0509, 0x0E13, 0x1C25, 0x002B, +}; + +static const u16 lan865x_revb0_fixup_cfg_regs[5] = { + 0x0084, 0x008A, 0x00AD, 0x00AE, 0x00AF +}; + +/* Pulled from AN1760 describing 'indirect read' + * + * write_register(0x4, 0x00D8, addr) + * write_register(0x4, 0x00DA, 0x2) + * return (int8)(read_register(0x4, 0x00D9)) + * + * 0x4 refers to memory map selector 4, which maps to MDIO_MMD_VEND2 + */ +static int lan865x_revb0_indirect_read(struct phy_device *phydev, u16 addr) +{ + int ret; + + ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, LAN865X_REG_CFGPARAM_ADDR, + addr); + if (ret) + return ret; + + ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, LAN865X_REG_CFGPARAM_CTRL, + LAN865X_CFGPARAM_READ_ENABLE); + if (ret) + return ret; + + return phy_read_mmd(phydev, MDIO_MMD_VEND2, LAN865X_REG_CFGPARAM_DATA); +} + +/* This is pulled straight from AN1760 from 'calculation of offset 1' & + * 'calculation of offset 2' + */ +static int lan865x_generate_cfg_offsets(struct phy_device *phydev, s8 offsets[2]) +{ + const u16 fixup_regs[2] = {0x0004, 0x0008}; + int ret; + + for (int i = 0; i < ARRAY_SIZE(fixup_regs); i++) { + ret = lan865x_revb0_indirect_read(phydev, fixup_regs[i]); + if (ret < 0) + return ret; + if (ret & BIT(4)) + offsets[i] = ret | 0xE0; + else + offsets[i] = ret; + } + + return 0; +} + +static int lan865x_read_cfg_params(struct phy_device *phydev, u16 cfg_params[]) +{ + int ret; + + for (int i = 0; i < ARRAY_SIZE(lan865x_revb0_fixup_cfg_regs); i++) { + ret = phy_read_mmd(phydev, MDIO_MMD_VEND2, + lan865x_revb0_fixup_cfg_regs[i]); + if (ret < 0) + return ret; + cfg_params[i] = (u16)ret; + } + + return 0; +} + +static int lan865x_write_cfg_params(struct phy_device *phydev, u16 cfg_params[]) +{ + int ret; + + for (int i = 0; i < ARRAY_SIZE(lan865x_revb0_fixup_cfg_regs); i++) { + ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, + lan865x_revb0_fixup_cfg_regs[i], + cfg_params[i]); + if (ret) + return ret; + } + + return 0; +} + +static int lan865x_setup_cfgparam(struct phy_device *phydev) +{ + u16 cfg_params[ARRAY_SIZE(lan865x_revb0_fixup_cfg_regs)]; + u16 cfg_results[5]; + s8 offsets[2]; + int ret; + + ret = lan865x_generate_cfg_offsets(phydev, offsets); + if (ret) + return ret; + + ret = lan865x_read_cfg_params(phydev, cfg_params); + if (ret) + return ret; + + cfg_results[0] = (cfg_params[0] & 0x000F) | + FIELD_PREP(GENMASK(15, 10), 9 + offsets[0]) | + FIELD_PREP(GENMASK(15, 4), 14 + offsets[0]); + cfg_results[1] = (cfg_params[1] & 0x03FF) | + FIELD_PREP(GENMASK(15, 10), 40 + offsets[1]); + cfg_results[2] = (cfg_params[2] & 0xC0C0) | + FIELD_PREP(GENMASK(15, 8), 5 + offsets[0]) | + (9 + offsets[0]); + cfg_results[3] = (cfg_params[3] & 0xC0C0) | + FIELD_PREP(GENMASK(15, 8), 9 + offsets[0]) | + (14 + offsets[0]); + cfg_results[4] = (cfg_params[4] & 0xC0C0) | + FIELD_PREP(GENMASK(15, 8), 17 + offsets[0]) | + (22 + offsets[0]); + + return lan865x_write_cfg_params(phydev, cfg_results); +} + +static int lan865x_revb0_config_init(struct phy_device *phydev) +{ + int ret; + + /* Reference to AN1760 + * https://ww1.microchip.com/downloads/aemDocuments/documents/AIS/ProductDocuments/SupportingCollateral/AN-LAN8650-1-Configuration-60001760.pdf + */ + for (int i = 0; i < ARRAY_SIZE(lan865x_revb0_fixup_registers); i++) { + ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, + lan865x_revb0_fixup_registers[i], + lan865x_revb0_fixup_values[i]); + if (ret) + return ret; + } + /* Function to calculate and write the configuration parameters in the + * 0x0084, 0x008A, 0x00AD, 0x00AE and 0x00AF registers (from AN1760) + */ + return lan865x_setup_cfgparam(phydev); +} + +static int lan867x_revb1_config_init(struct phy_device *phydev) +{ + int err; + + /* The chip completes a reset in 3us, we might get here earlier than + * that, as an added margin we'll conditionally sleep 5us. + */ + err = phy_read_mmd(phydev, MDIO_MMD_VEND2, LAN867X_REG_STS2); + if (err < 0) + return err; + + if (!(err & LAN867x_RESET_COMPLETE_STS)) { + udelay(5); + err = phy_read_mmd(phydev, MDIO_MMD_VEND2, LAN867X_REG_STS2); + if (err < 0) + return err; + if (!(err & LAN867x_RESET_COMPLETE_STS)) { + phydev_err(phydev, "PHY reset failed\n"); + return -ENODEV; + } + } + + /* Reference to AN1699 + * https://ww1.microchip.com/downloads/aemDocuments/documents/AIS/ProductDocuments/SupportingCollateral/AN-LAN8670-1-2-config-60001699.pdf + * AN1699 says Read, Modify, Write, but the Write is not required if the + * register already has the required value. So it is safe to use + * phy_modify_mmd here. + */ + for (int i = 0; i < ARRAY_SIZE(lan867x_revb1_fixup_registers); i++) { + err = phy_modify_mmd(phydev, MDIO_MMD_VEND2, + lan867x_revb1_fixup_registers[i], + lan867x_revb1_fixup_masks[i], + lan867x_revb1_fixup_values[i]); + if (err) + return err; + } + + return 0; +} + +static int lan86xx_read_status(struct phy_device *phydev) +{ + /* The phy has some limitations, namely: + * - always reports link up + * - only supports 10MBit half duplex + * - does not support auto negotiate + */ + phydev->link = 1; + phydev->duplex = DUPLEX_HALF; + phydev->speed = SPEED_10; + phydev->autoneg = AUTONEG_DISABLE; + + return 0; +} + +static struct phy_driver microchip_t1s_driver[] = { + { + PHY_ID_MATCH_EXACT(PHY_ID_LAN867X_REVB1), + .name = "LAN867X Rev.B1", + .features = PHY_BASIC_T1S_P2MP_FEATURES, + .config_init = lan867x_revb1_config_init, + .read_status = lan86xx_read_status, + .get_plca_cfg = genphy_c45_plca_get_cfg, + .set_plca_cfg = genphy_c45_plca_set_cfg, + .get_plca_status = genphy_c45_plca_get_status, + }, + { + PHY_ID_MATCH_EXACT(PHY_ID_LAN865X_REVB0), + .name = "LAN865X Rev.B0 Internal Phy", + .features = PHY_BASIC_T1S_P2MP_FEATURES, + .config_init = lan865x_revb0_config_init, + .read_status = lan86xx_read_status, + .get_plca_cfg = genphy_c45_plca_get_cfg, + .set_plca_cfg = genphy_c45_plca_set_cfg, + .get_plca_status = genphy_c45_plca_get_status, + }, +}; + +module_phy_driver(microchip_t1s_driver); + +static struct mdio_device_id __maybe_unused tbl[] = { + { PHY_ID_MATCH_EXACT(PHY_ID_LAN867X_REVB1) }, + { PHY_ID_MATCH_EXACT(PHY_ID_LAN865X_REVB0) }, + { } +}; + +MODULE_DEVICE_TABLE(mdio, tbl); + +MODULE_DESCRIPTION("Microchip 10BASE-T1S PHYs driver"); +MODULE_AUTHOR("Ramón Nordin Rodriguez"); +MODULE_LICENSE("GPL"); |