diff options
Diffstat (limited to 'drivers/net/phy/qcom/at803x.c')
| -rw-r--r-- | drivers/net/phy/qcom/at803x.c | 1108 |
1 files changed, 1108 insertions, 0 deletions
diff --git a/drivers/net/phy/qcom/at803x.c b/drivers/net/phy/qcom/at803x.c new file mode 100644 index 0000000000..e79657f76b --- /dev/null +++ b/drivers/net/phy/qcom/at803x.c @@ -0,0 +1,1108 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * drivers/net/phy/at803x.c + * + * Driver for Qualcomm Atheros AR803x PHY + * + * Author: Matus Ujhelyi <ujhelyi.m@gmail.com> + */ + +#include <linux/phy.h> +#include <linux/module.h> +#include <linux/string.h> +#include <linux/netdevice.h> +#include <linux/etherdevice.h> +#include <linux/ethtool_netlink.h> +#include <linux/bitfield.h> +#include <linux/regulator/of_regulator.h> +#include <linux/regulator/driver.h> +#include <linux/regulator/consumer.h> +#include <linux/of.h> +#include <linux/phylink.h> +#include <linux/sfp.h> +#include <dt-bindings/net/qca-ar803x.h> + +#include "qcom.h" + +#define AT803X_LED_CONTROL 0x18 + +#define AT803X_PHY_MMD3_WOL_CTRL 0x8012 +#define AT803X_WOL_EN BIT(5) + +#define AT803X_REG_CHIP_CONFIG 0x1f +#define AT803X_BT_BX_REG_SEL 0x8000 + +#define AT803X_MODE_CFG_MASK 0x0F +#define AT803X_MODE_CFG_BASET_RGMII 0x00 +#define AT803X_MODE_CFG_BASET_SGMII 0x01 +#define AT803X_MODE_CFG_BX1000_RGMII_50OHM 0x02 +#define AT803X_MODE_CFG_BX1000_RGMII_75OHM 0x03 +#define AT803X_MODE_CFG_BX1000_CONV_50OHM 0x04 +#define AT803X_MODE_CFG_BX1000_CONV_75OHM 0x05 +#define AT803X_MODE_CFG_FX100_RGMII_50OHM 0x06 +#define AT803X_MODE_CFG_FX100_CONV_50OHM 0x07 +#define AT803X_MODE_CFG_RGMII_AUTO_MDET 0x0B +#define AT803X_MODE_CFG_FX100_RGMII_75OHM 0x0E +#define AT803X_MODE_CFG_FX100_CONV_75OHM 0x0F + +#define AT803X_PSSR 0x11 /*PHY-Specific Status Register*/ +#define AT803X_PSSR_MR_AN_COMPLETE 0x0200 + +#define AT803X_DEBUG_REG_1F 0x1F +#define AT803X_DEBUG_PLL_ON BIT(2) +#define AT803X_DEBUG_RGMII_1V8 BIT(3) + +/* AT803x supports either the XTAL input pad, an internal PLL or the + * DSP as clock reference for the clock output pad. The XTAL reference + * is only used for 25 MHz output, all other frequencies need the PLL. + * The DSP as a clock reference is used in synchronous ethernet + * applications. + * + * By default the PLL is only enabled if there is a link. Otherwise + * the PHY will go into low power state and disabled the PLL. You can + * set the PLL_ON bit (see debug register 0x1f) to keep the PLL always + * enabled. + */ +#define AT803X_MMD7_CLK25M 0x8016 +#define AT803X_CLK_OUT_MASK GENMASK(4, 2) +#define AT803X_CLK_OUT_25MHZ_XTAL 0 +#define AT803X_CLK_OUT_25MHZ_DSP 1 +#define AT803X_CLK_OUT_50MHZ_PLL 2 +#define AT803X_CLK_OUT_50MHZ_DSP 3 +#define AT803X_CLK_OUT_62_5MHZ_PLL 4 +#define AT803X_CLK_OUT_62_5MHZ_DSP 5 +#define AT803X_CLK_OUT_125MHZ_PLL 6 +#define AT803X_CLK_OUT_125MHZ_DSP 7 + +/* The AR8035 has another mask which is compatible with the AR8031/AR8033 mask + * but doesn't support choosing between XTAL/PLL and DSP. + */ +#define AT8035_CLK_OUT_MASK GENMASK(4, 3) + +#define AT803X_CLK_OUT_STRENGTH_MASK GENMASK(8, 7) +#define AT803X_CLK_OUT_STRENGTH_FULL 0 +#define AT803X_CLK_OUT_STRENGTH_HALF 1 +#define AT803X_CLK_OUT_STRENGTH_QUARTER 2 + +#define AT803X_MMD3_SMARTEEE_CTL1 0x805b +#define AT803X_MMD3_SMARTEEE_CTL2 0x805c +#define AT803X_MMD3_SMARTEEE_CTL3 0x805d +#define AT803X_MMD3_SMARTEEE_CTL3_LPI_EN BIT(8) + +#define ATH9331_PHY_ID 0x004dd041 +#define ATH8030_PHY_ID 0x004dd076 +#define ATH8031_PHY_ID 0x004dd074 +#define ATH8032_PHY_ID 0x004dd023 +#define ATH8035_PHY_ID 0x004dd072 +#define AT8030_PHY_ID_MASK 0xffffffef + +#define QCA9561_PHY_ID 0x004dd042 + +#define AT803X_PAGE_FIBER 0 +#define AT803X_PAGE_COPPER 1 + +/* don't turn off internal PLL */ +#define AT803X_KEEP_PLL_ENABLED BIT(0) +#define AT803X_DISABLE_SMARTEEE BIT(1) + +/* disable hibernation mode */ +#define AT803X_DISABLE_HIBERNATION_MODE BIT(2) + +MODULE_DESCRIPTION("Qualcomm Atheros AR803x PHY driver"); +MODULE_AUTHOR("Matus Ujhelyi"); +MODULE_LICENSE("GPL"); + +struct at803x_priv { + int flags; + u16 clk_25m_reg; + u16 clk_25m_mask; + u8 smarteee_lpi_tw_1g; + u8 smarteee_lpi_tw_100m; + bool is_fiber; + bool is_1000basex; + struct regulator_dev *vddio_rdev; + struct regulator_dev *vddh_rdev; +}; + +struct at803x_context { + u16 bmcr; + u16 advertise; + u16 control1000; + u16 int_enable; + u16 smart_speed; + u16 led_control; +}; + +static int at803x_write_page(struct phy_device *phydev, int page) +{ + int mask; + int set; + + if (page == AT803X_PAGE_COPPER) { + set = AT803X_BT_BX_REG_SEL; + mask = 0; + } else { + set = 0; + mask = AT803X_BT_BX_REG_SEL; + } + + return __phy_modify(phydev, AT803X_REG_CHIP_CONFIG, mask, set); +} + +static int at803x_read_page(struct phy_device *phydev) +{ + int ccr = __phy_read(phydev, AT803X_REG_CHIP_CONFIG); + + if (ccr < 0) + return ccr; + + if (ccr & AT803X_BT_BX_REG_SEL) + return AT803X_PAGE_COPPER; + + return AT803X_PAGE_FIBER; +} + +static int at803x_enable_rx_delay(struct phy_device *phydev) +{ + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, 0, + AT803X_DEBUG_RX_CLK_DLY_EN); +} + +static int at803x_enable_tx_delay(struct phy_device *phydev) +{ + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_SYSTEM_CTRL_MODE, 0, + AT803X_DEBUG_TX_CLK_DLY_EN); +} + +static int at803x_disable_rx_delay(struct phy_device *phydev) +{ + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, + AT803X_DEBUG_RX_CLK_DLY_EN, 0); +} + +static int at803x_disable_tx_delay(struct phy_device *phydev) +{ + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_SYSTEM_CTRL_MODE, + AT803X_DEBUG_TX_CLK_DLY_EN, 0); +} + +/* save relevant PHY registers to private copy */ +static void at803x_context_save(struct phy_device *phydev, + struct at803x_context *context) +{ + context->bmcr = phy_read(phydev, MII_BMCR); + context->advertise = phy_read(phydev, MII_ADVERTISE); + context->control1000 = phy_read(phydev, MII_CTRL1000); + context->int_enable = phy_read(phydev, AT803X_INTR_ENABLE); + context->smart_speed = phy_read(phydev, AT803X_SMART_SPEED); + context->led_control = phy_read(phydev, AT803X_LED_CONTROL); +} + +/* restore relevant PHY registers from private copy */ +static void at803x_context_restore(struct phy_device *phydev, + const struct at803x_context *context) +{ + phy_write(phydev, MII_BMCR, context->bmcr); + phy_write(phydev, MII_ADVERTISE, context->advertise); + phy_write(phydev, MII_CTRL1000, context->control1000); + phy_write(phydev, AT803X_INTR_ENABLE, context->int_enable); + phy_write(phydev, AT803X_SMART_SPEED, context->smart_speed); + phy_write(phydev, AT803X_LED_CONTROL, context->led_control); +} + +static int at803x_suspend(struct phy_device *phydev) +{ + int value; + int wol_enabled; + + value = phy_read(phydev, AT803X_INTR_ENABLE); + wol_enabled = value & AT803X_INTR_ENABLE_WOL; + + if (wol_enabled) + value = BMCR_ISOLATE; + else + value = BMCR_PDOWN; + + phy_modify(phydev, MII_BMCR, 0, value); + + return 0; +} + +static int at803x_resume(struct phy_device *phydev) +{ + return phy_modify(phydev, MII_BMCR, BMCR_PDOWN | BMCR_ISOLATE, 0); +} + +static int at803x_parse_dt(struct phy_device *phydev) +{ + struct device_node *node = phydev->mdio.dev.of_node; + struct at803x_priv *priv = phydev->priv; + u32 freq, strength, tw; + unsigned int sel; + int ret; + + if (!IS_ENABLED(CONFIG_OF_MDIO)) + return 0; + + if (of_property_read_bool(node, "qca,disable-smarteee")) + priv->flags |= AT803X_DISABLE_SMARTEEE; + + if (of_property_read_bool(node, "qca,disable-hibernation-mode")) + priv->flags |= AT803X_DISABLE_HIBERNATION_MODE; + + if (!of_property_read_u32(node, "qca,smarteee-tw-us-1g", &tw)) { + if (!tw || tw > 255) { + phydev_err(phydev, "invalid qca,smarteee-tw-us-1g\n"); + return -EINVAL; + } + priv->smarteee_lpi_tw_1g = tw; + } + + if (!of_property_read_u32(node, "qca,smarteee-tw-us-100m", &tw)) { + if (!tw || tw > 255) { + phydev_err(phydev, "invalid qca,smarteee-tw-us-100m\n"); + return -EINVAL; + } + priv->smarteee_lpi_tw_100m = tw; + } + + ret = of_property_read_u32(node, "qca,clk-out-frequency", &freq); + if (!ret) { + switch (freq) { + case 25000000: + sel = AT803X_CLK_OUT_25MHZ_XTAL; + break; + case 50000000: + sel = AT803X_CLK_OUT_50MHZ_PLL; + break; + case 62500000: + sel = AT803X_CLK_OUT_62_5MHZ_PLL; + break; + case 125000000: + sel = AT803X_CLK_OUT_125MHZ_PLL; + break; + default: + phydev_err(phydev, "invalid qca,clk-out-frequency\n"); + return -EINVAL; + } + + priv->clk_25m_reg |= FIELD_PREP(AT803X_CLK_OUT_MASK, sel); + priv->clk_25m_mask |= AT803X_CLK_OUT_MASK; + } + + ret = of_property_read_u32(node, "qca,clk-out-strength", &strength); + if (!ret) { + priv->clk_25m_mask |= AT803X_CLK_OUT_STRENGTH_MASK; + switch (strength) { + case AR803X_STRENGTH_FULL: + priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_FULL; + break; + case AR803X_STRENGTH_HALF: + priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_HALF; + break; + case AR803X_STRENGTH_QUARTER: + priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_QUARTER; + break; + default: + phydev_err(phydev, "invalid qca,clk-out-strength\n"); + return -EINVAL; + } + } + + return 0; +} + +static int at803x_probe(struct phy_device *phydev) +{ + struct device *dev = &phydev->mdio.dev; + struct at803x_priv *priv; + int ret; + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + phydev->priv = priv; + + ret = at803x_parse_dt(phydev); + if (ret) + return ret; + + return 0; +} + +static int at803x_get_features(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + int err; + + err = genphy_read_abilities(phydev); + if (err) + return err; + + if (phydev->drv->phy_id != ATH8031_PHY_ID) + return 0; + + /* AR8031/AR8033 have different status registers + * for copper and fiber operation. However, the + * extended status register is the same for both + * operation modes. + * + * As a result of that, ESTATUS_1000_XFULL is set + * to 1 even when operating in copper TP mode. + * + * Remove this mode from the supported link modes + * when not operating in 1000BaseX mode. + */ + if (!priv->is_1000basex) + linkmode_clear_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT, + phydev->supported); + + return 0; +} + +static int at803x_smarteee_config(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + u16 mask = 0, val = 0; + int ret; + + if (priv->flags & AT803X_DISABLE_SMARTEEE) + return phy_modify_mmd(phydev, MDIO_MMD_PCS, + AT803X_MMD3_SMARTEEE_CTL3, + AT803X_MMD3_SMARTEEE_CTL3_LPI_EN, 0); + + if (priv->smarteee_lpi_tw_1g) { + mask |= 0xff00; + val |= priv->smarteee_lpi_tw_1g << 8; + } + if (priv->smarteee_lpi_tw_100m) { + mask |= 0x00ff; + val |= priv->smarteee_lpi_tw_100m; + } + if (!mask) + return 0; + + ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, AT803X_MMD3_SMARTEEE_CTL1, + mask, val); + if (ret) + return ret; + + return phy_modify_mmd(phydev, MDIO_MMD_PCS, AT803X_MMD3_SMARTEEE_CTL3, + AT803X_MMD3_SMARTEEE_CTL3_LPI_EN, + AT803X_MMD3_SMARTEEE_CTL3_LPI_EN); +} + +static int at803x_clk_out_config(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + + if (!priv->clk_25m_mask) + return 0; + + return phy_modify_mmd(phydev, MDIO_MMD_AN, AT803X_MMD7_CLK25M, + priv->clk_25m_mask, priv->clk_25m_reg); +} + +static int at8031_pll_config(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + + /* The default after hardware reset is PLL OFF. After a soft reset, the + * values are retained. + */ + if (priv->flags & AT803X_KEEP_PLL_ENABLED) + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F, + 0, AT803X_DEBUG_PLL_ON); + else + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F, + AT803X_DEBUG_PLL_ON, 0); +} + +static int at803x_hibernation_mode_config(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + + /* The default after hardware reset is hibernation mode enabled. After + * software reset, the value is retained. + */ + if (!(priv->flags & AT803X_DISABLE_HIBERNATION_MODE)) + return 0; + + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_HIB_CTRL, + AT803X_DEBUG_HIB_CTRL_PS_HIB_EN, 0); +} + +static int at803x_config_init(struct phy_device *phydev) +{ + int ret; + + /* The RX and TX delay default is: + * after HW reset: RX delay enabled and TX delay disabled + * after SW reset: RX delay enabled, while TX delay retains the + * value before reset. + */ + if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID || + phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) + ret = at803x_enable_rx_delay(phydev); + else + ret = at803x_disable_rx_delay(phydev); + if (ret < 0) + return ret; + + if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID || + phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) + ret = at803x_enable_tx_delay(phydev); + else + ret = at803x_disable_tx_delay(phydev); + if (ret < 0) + return ret; + + ret = at803x_smarteee_config(phydev); + if (ret < 0) + return ret; + + ret = at803x_clk_out_config(phydev); + if (ret < 0) + return ret; + + ret = at803x_hibernation_mode_config(phydev); + if (ret < 0) + return ret; + + /* Ar803x extended next page bit is enabled by default. Cisco + * multigig switches read this bit and attempt to negotiate 10Gbps + * rates even if the next page bit is disabled. This is incorrect + * behaviour but we still need to accommodate it. XNP is only needed + * for 10Gbps support, so disable XNP. + */ + return phy_modify(phydev, MII_ADVERTISE, MDIO_AN_CTRL1_XNP, 0); +} + +static void at803x_link_change_notify(struct phy_device *phydev) +{ + /* + * Conduct a hardware reset for AT8030 every time a link loss is + * signalled. This is necessary to circumvent a hardware bug that + * occurs when the cable is unplugged while TX packets are pending + * in the FIFO. In such cases, the FIFO enters an error mode it + * cannot recover from by software. + */ + if (phydev->state == PHY_NOLINK && phydev->mdio.reset_gpio) { + struct at803x_context context; + + at803x_context_save(phydev, &context); + + phy_device_reset(phydev, 1); + usleep_range(1000, 2000); + phy_device_reset(phydev, 0); + usleep_range(1000, 2000); + + at803x_context_restore(phydev, &context); + + phydev_dbg(phydev, "%s(): phy was reset\n", __func__); + } +} + +static int at803x_config_aneg(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + int ret; + + ret = at803x_prepare_config_aneg(phydev); + if (ret) + return ret; + + if (priv->is_1000basex) + return genphy_c37_config_aneg(phydev); + + return genphy_config_aneg(phydev); +} + +static int at803x_cable_test_result_trans(u16 status) +{ + switch (FIELD_GET(AT803X_CDT_STATUS_STAT_MASK, status)) { + case AT803X_CDT_STATUS_STAT_NORMAL: + return ETHTOOL_A_CABLE_RESULT_CODE_OK; + case AT803X_CDT_STATUS_STAT_SHORT: + return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT; + case AT803X_CDT_STATUS_STAT_OPEN: + return ETHTOOL_A_CABLE_RESULT_CODE_OPEN; + case AT803X_CDT_STATUS_STAT_FAIL: + default: + return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC; + } +} + +static bool at803x_cdt_test_failed(u16 status) +{ + return FIELD_GET(AT803X_CDT_STATUS_STAT_MASK, status) == + AT803X_CDT_STATUS_STAT_FAIL; +} + +static bool at803x_cdt_fault_length_valid(u16 status) +{ + switch (FIELD_GET(AT803X_CDT_STATUS_STAT_MASK, status)) { + case AT803X_CDT_STATUS_STAT_OPEN: + case AT803X_CDT_STATUS_STAT_SHORT: + return true; + } + return false; +} + +static int at803x_cable_test_one_pair(struct phy_device *phydev, int pair) +{ + static const int ethtool_pair[] = { + ETHTOOL_A_CABLE_PAIR_A, + ETHTOOL_A_CABLE_PAIR_B, + ETHTOOL_A_CABLE_PAIR_C, + ETHTOOL_A_CABLE_PAIR_D, + }; + int ret, val; + + val = FIELD_PREP(AT803X_CDT_MDI_PAIR_MASK, pair) | + AT803X_CDT_ENABLE_TEST; + ret = at803x_cdt_start(phydev, val); + if (ret) + return ret; + + ret = at803x_cdt_wait_for_completion(phydev, AT803X_CDT_ENABLE_TEST); + if (ret) + return ret; + + val = phy_read(phydev, AT803X_CDT_STATUS); + if (val < 0) + return val; + + if (at803x_cdt_test_failed(val)) + return 0; + + ethnl_cable_test_result(phydev, ethtool_pair[pair], + at803x_cable_test_result_trans(val)); + + if (at803x_cdt_fault_length_valid(val)) { + val = FIELD_GET(AT803X_CDT_STATUS_DELTA_TIME_MASK, val); + ethnl_cable_test_fault_length(phydev, ethtool_pair[pair], + at803x_cdt_fault_length(val)); + } + + return 1; +} + +static int at803x_cable_test_get_status(struct phy_device *phydev, + bool *finished, unsigned long pair_mask) +{ + int retries = 20; + int pair, ret; + + *finished = false; + + /* According to the datasheet the CDT can be performed when + * there is no link partner or when the link partner is + * auto-negotiating. Starting the test will restart the AN + * automatically. It seems that doing this repeatedly we will + * get a slot where our link partner won't disturb our + * measurement. + */ + while (pair_mask && retries--) { + for_each_set_bit(pair, &pair_mask, 4) { + ret = at803x_cable_test_one_pair(phydev, pair); + if (ret < 0) + return ret; + if (ret) + clear_bit(pair, &pair_mask); + } + if (pair_mask) + msleep(250); + } + + *finished = true; + + return 0; +} + +static void at803x_cable_test_autoneg(struct phy_device *phydev) +{ + /* Enable auto-negotiation, but advertise no capabilities, no link + * will be established. A restart of the auto-negotiation is not + * required, because the cable test will automatically break the link. + */ + phy_write(phydev, MII_BMCR, BMCR_ANENABLE); + phy_write(phydev, MII_ADVERTISE, ADVERTISE_CSMA); +} + +static int at803x_cable_test_start(struct phy_device *phydev) +{ + at803x_cable_test_autoneg(phydev); + /* we do all the (time consuming) work later */ + return 0; +} + +static int at8031_rgmii_reg_set_voltage_sel(struct regulator_dev *rdev, + unsigned int selector) +{ + struct phy_device *phydev = rdev_get_drvdata(rdev); + + if (selector) + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F, + 0, AT803X_DEBUG_RGMII_1V8); + else + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F, + AT803X_DEBUG_RGMII_1V8, 0); +} + +static int at8031_rgmii_reg_get_voltage_sel(struct regulator_dev *rdev) +{ + struct phy_device *phydev = rdev_get_drvdata(rdev); + int val; + + val = at803x_debug_reg_read(phydev, AT803X_DEBUG_REG_1F); + if (val < 0) + return val; + + return (val & AT803X_DEBUG_RGMII_1V8) ? 1 : 0; +} + +static const struct regulator_ops vddio_regulator_ops = { + .list_voltage = regulator_list_voltage_table, + .set_voltage_sel = at8031_rgmii_reg_set_voltage_sel, + .get_voltage_sel = at8031_rgmii_reg_get_voltage_sel, +}; + +static const unsigned int vddio_voltage_table[] = { + 1500000, + 1800000, +}; + +static const struct regulator_desc vddio_desc = { + .name = "vddio", + .of_match = of_match_ptr("vddio-regulator"), + .n_voltages = ARRAY_SIZE(vddio_voltage_table), + .volt_table = vddio_voltage_table, + .ops = &vddio_regulator_ops, + .type = REGULATOR_VOLTAGE, + .owner = THIS_MODULE, +}; + +static const struct regulator_ops vddh_regulator_ops = { +}; + +static const struct regulator_desc vddh_desc = { + .name = "vddh", + .of_match = of_match_ptr("vddh-regulator"), + .n_voltages = 1, + .fixed_uV = 2500000, + .ops = &vddh_regulator_ops, + .type = REGULATOR_VOLTAGE, + .owner = THIS_MODULE, +}; + +static int at8031_register_regulators(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + struct device *dev = &phydev->mdio.dev; + struct regulator_config config = { }; + + config.dev = dev; + config.driver_data = phydev; + + priv->vddio_rdev = devm_regulator_register(dev, &vddio_desc, &config); + if (IS_ERR(priv->vddio_rdev)) { + phydev_err(phydev, "failed to register VDDIO regulator\n"); + return PTR_ERR(priv->vddio_rdev); + } + + priv->vddh_rdev = devm_regulator_register(dev, &vddh_desc, &config); + if (IS_ERR(priv->vddh_rdev)) { + phydev_err(phydev, "failed to register VDDH regulator\n"); + return PTR_ERR(priv->vddh_rdev); + } + + return 0; +} + +static int at8031_sfp_insert(void *upstream, const struct sfp_eeprom_id *id) +{ + struct phy_device *phydev = upstream; + __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_support); + __ETHTOOL_DECLARE_LINK_MODE_MASK(sfp_support); + DECLARE_PHY_INTERFACE_MASK(interfaces); + phy_interface_t iface; + + linkmode_zero(phy_support); + phylink_set(phy_support, 1000baseX_Full); + phylink_set(phy_support, 1000baseT_Full); + phylink_set(phy_support, Autoneg); + phylink_set(phy_support, Pause); + phylink_set(phy_support, Asym_Pause); + + linkmode_zero(sfp_support); + sfp_parse_support(phydev->sfp_bus, id, sfp_support, interfaces); + /* Some modules support 10G modes as well as others we support. + * Mask out non-supported modes so the correct interface is picked. + */ + linkmode_and(sfp_support, phy_support, sfp_support); + + if (linkmode_empty(sfp_support)) { + dev_err(&phydev->mdio.dev, "incompatible SFP module inserted\n"); + return -EINVAL; + } + + iface = sfp_select_interface(phydev->sfp_bus, sfp_support); + + /* Only 1000Base-X is supported by AR8031/8033 as the downstream SerDes + * interface for use with SFP modules. + * However, some copper modules detected as having a preferred SGMII + * interface do default to and function in 1000Base-X mode, so just + * print a warning and allow such modules, as they may have some chance + * of working. + */ + if (iface == PHY_INTERFACE_MODE_SGMII) + dev_warn(&phydev->mdio.dev, "module may not function if 1000Base-X not supported\n"); + else if (iface != PHY_INTERFACE_MODE_1000BASEX) + return -EINVAL; + + return 0; +} + +static const struct sfp_upstream_ops at8031_sfp_ops = { + .attach = phy_sfp_attach, + .detach = phy_sfp_detach, + .module_insert = at8031_sfp_insert, +}; + +static int at8031_parse_dt(struct phy_device *phydev) +{ + struct device_node *node = phydev->mdio.dev.of_node; + struct at803x_priv *priv = phydev->priv; + int ret; + + if (of_property_read_bool(node, "qca,keep-pll-enabled")) + priv->flags |= AT803X_KEEP_PLL_ENABLED; + + ret = at8031_register_regulators(phydev); + if (ret < 0) + return ret; + + ret = devm_regulator_get_enable_optional(&phydev->mdio.dev, + "vddio"); + if (ret) { + phydev_err(phydev, "failed to get VDDIO regulator\n"); + return ret; + } + + /* Only AR8031/8033 support 1000Base-X for SFP modules */ + return phy_sfp_probe(phydev, &at8031_sfp_ops); +} + +static int at8031_probe(struct phy_device *phydev) +{ + struct at803x_priv *priv; + int mode_cfg; + int ccr; + int ret; + + ret = at803x_probe(phydev); + if (ret) + return ret; + + priv = phydev->priv; + + /* Only supported on AR8031/AR8033, the AR8030/AR8035 use strapping + * options. + */ + ret = at8031_parse_dt(phydev); + if (ret) + return ret; + + ccr = phy_read(phydev, AT803X_REG_CHIP_CONFIG); + if (ccr < 0) + return ccr; + mode_cfg = ccr & AT803X_MODE_CFG_MASK; + + switch (mode_cfg) { + case AT803X_MODE_CFG_BX1000_RGMII_50OHM: + case AT803X_MODE_CFG_BX1000_RGMII_75OHM: + priv->is_1000basex = true; + fallthrough; + case AT803X_MODE_CFG_FX100_RGMII_50OHM: + case AT803X_MODE_CFG_FX100_RGMII_75OHM: + priv->is_fiber = true; + break; + } + + /* Disable WoL in 1588 register which is enabled + * by default + */ + return phy_modify_mmd(phydev, MDIO_MMD_PCS, + AT803X_PHY_MMD3_WOL_CTRL, + AT803X_WOL_EN, 0); +} + +static int at8031_config_init(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + int ret; + + /* Some bootloaders leave the fiber page selected. + * Switch to the appropriate page (fiber or copper), as otherwise we + * read the PHY capabilities from the wrong page. + */ + phy_lock_mdio_bus(phydev); + ret = at803x_write_page(phydev, + priv->is_fiber ? AT803X_PAGE_FIBER : + AT803X_PAGE_COPPER); + phy_unlock_mdio_bus(phydev); + if (ret) + return ret; + + ret = at8031_pll_config(phydev); + if (ret < 0) + return ret; + + return at803x_config_init(phydev); +} + +static int at8031_set_wol(struct phy_device *phydev, + struct ethtool_wolinfo *wol) +{ + int ret; + + /* First setup MAC address and enable WOL interrupt */ + ret = at803x_set_wol(phydev, wol); + if (ret) + return ret; + + if (wol->wolopts & WAKE_MAGIC) + /* Enable WOL function for 1588 */ + ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, + AT803X_PHY_MMD3_WOL_CTRL, + 0, AT803X_WOL_EN); + else + /* Disable WoL function for 1588 */ + ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, + AT803X_PHY_MMD3_WOL_CTRL, + AT803X_WOL_EN, 0); + + return ret; +} + +static int at8031_config_intr(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + int err, value = 0; + + if (phydev->interrupts == PHY_INTERRUPT_ENABLED && + priv->is_fiber) { + /* Clear any pending interrupts */ + err = at803x_ack_interrupt(phydev); + if (err) + return err; + + value |= AT803X_INTR_ENABLE_LINK_FAIL_BX; + value |= AT803X_INTR_ENABLE_LINK_SUCCESS_BX; + + err = phy_set_bits(phydev, AT803X_INTR_ENABLE, value); + if (err) + return err; + } + + return at803x_config_intr(phydev); +} + +/* AR8031 and AR8033 share the same read status logic */ +static int at8031_read_status(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + bool changed; + + if (priv->is_1000basex) + return genphy_c37_read_status(phydev, &changed); + + return at803x_read_status(phydev); +} + +/* AR8031 and AR8035 share the same cable test get status reg */ +static int at8031_cable_test_get_status(struct phy_device *phydev, + bool *finished) +{ + return at803x_cable_test_get_status(phydev, finished, 0xf); +} + +/* AR8031 and AR8035 share the same cable test start logic */ +static int at8031_cable_test_start(struct phy_device *phydev) +{ + at803x_cable_test_autoneg(phydev); + phy_write(phydev, MII_CTRL1000, 0); + /* we do all the (time consuming) work later */ + return 0; +} + +/* AR8032, AR9331 and QCA9561 share the same cable test get status reg */ +static int at8032_cable_test_get_status(struct phy_device *phydev, + bool *finished) +{ + return at803x_cable_test_get_status(phydev, finished, 0x3); +} + +static int at8035_parse_dt(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + + /* Mask is set by the generic at803x_parse_dt + * if property is set. Assume property is set + * with the mask not zero. + */ + if (priv->clk_25m_mask) { + /* Fixup for the AR8030/AR8035. This chip has another mask and + * doesn't support the DSP reference. Eg. the lowest bit of the + * mask. The upper two bits select the same frequencies. Mask + * the lowest bit here. + * + * Warning: + * There was no datasheet for the AR8030 available so this is + * just a guess. But the AR8035 is listed as pin compatible + * to the AR8030 so there might be a good chance it works on + * the AR8030 too. + */ + priv->clk_25m_reg &= AT8035_CLK_OUT_MASK; + priv->clk_25m_mask &= AT8035_CLK_OUT_MASK; + } + + return 0; +} + +/* AR8030 and AR8035 shared the same special mask for clk_25m */ +static int at8035_probe(struct phy_device *phydev) +{ + int ret; + + ret = at803x_probe(phydev); + if (ret) + return ret; + + return at8035_parse_dt(phydev); +} + +static struct phy_driver at803x_driver[] = { +{ + /* Qualcomm Atheros AR8035 */ + PHY_ID_MATCH_EXACT(ATH8035_PHY_ID), + .name = "Qualcomm Atheros AR8035", + .flags = PHY_POLL_CABLE_TEST, + .probe = at8035_probe, + .config_aneg = at803x_config_aneg, + .config_init = at803x_config_init, + .soft_reset = genphy_soft_reset, + .set_wol = at803x_set_wol, + .get_wol = at803x_get_wol, + .suspend = at803x_suspend, + .resume = at803x_resume, + /* PHY_GBIT_FEATURES */ + .read_status = at803x_read_status, + .config_intr = at803x_config_intr, + .handle_interrupt = at803x_handle_interrupt, + .get_tunable = at803x_get_tunable, + .set_tunable = at803x_set_tunable, + .cable_test_start = at8031_cable_test_start, + .cable_test_get_status = at8031_cable_test_get_status, +}, { + /* Qualcomm Atheros AR8030 */ + .phy_id = ATH8030_PHY_ID, + .name = "Qualcomm Atheros AR8030", + .phy_id_mask = AT8030_PHY_ID_MASK, + .probe = at8035_probe, + .config_init = at803x_config_init, + .link_change_notify = at803x_link_change_notify, + .set_wol = at803x_set_wol, + .get_wol = at803x_get_wol, + .suspend = at803x_suspend, + .resume = at803x_resume, + /* PHY_BASIC_FEATURES */ + .config_intr = at803x_config_intr, + .handle_interrupt = at803x_handle_interrupt, +}, { + /* Qualcomm Atheros AR8031/AR8033 */ + PHY_ID_MATCH_EXACT(ATH8031_PHY_ID), + .name = "Qualcomm Atheros AR8031/AR8033", + .flags = PHY_POLL_CABLE_TEST, + .probe = at8031_probe, + .config_init = at8031_config_init, + .config_aneg = at803x_config_aneg, + .soft_reset = genphy_soft_reset, + .set_wol = at8031_set_wol, + .get_wol = at803x_get_wol, + .suspend = at803x_suspend, + .resume = at803x_resume, + .read_page = at803x_read_page, + .write_page = at803x_write_page, + .get_features = at803x_get_features, + .read_status = at8031_read_status, + .config_intr = at8031_config_intr, + .handle_interrupt = at803x_handle_interrupt, + .get_tunable = at803x_get_tunable, + .set_tunable = at803x_set_tunable, + .cable_test_start = at8031_cable_test_start, + .cable_test_get_status = at8031_cable_test_get_status, +}, { + /* Qualcomm Atheros AR8032 */ + PHY_ID_MATCH_EXACT(ATH8032_PHY_ID), + .name = "Qualcomm Atheros AR8032", + .probe = at803x_probe, + .flags = PHY_POLL_CABLE_TEST, + .config_init = at803x_config_init, + .link_change_notify = at803x_link_change_notify, + .suspend = at803x_suspend, + .resume = at803x_resume, + /* PHY_BASIC_FEATURES */ + .config_intr = at803x_config_intr, + .handle_interrupt = at803x_handle_interrupt, + .cable_test_start = at803x_cable_test_start, + .cable_test_get_status = at8032_cable_test_get_status, +}, { + /* ATHEROS AR9331 */ + PHY_ID_MATCH_EXACT(ATH9331_PHY_ID), + .name = "Qualcomm Atheros AR9331 built-in PHY", + .probe = at803x_probe, + .suspend = at803x_suspend, + .resume = at803x_resume, + .flags = PHY_POLL_CABLE_TEST, + /* PHY_BASIC_FEATURES */ + .config_intr = at803x_config_intr, + .handle_interrupt = at803x_handle_interrupt, + .cable_test_start = at803x_cable_test_start, + .cable_test_get_status = at8032_cable_test_get_status, + .read_status = at803x_read_status, + .soft_reset = genphy_soft_reset, + .config_aneg = at803x_config_aneg, +}, { + /* Qualcomm Atheros QCA9561 */ + PHY_ID_MATCH_EXACT(QCA9561_PHY_ID), + .name = "Qualcomm Atheros QCA9561 built-in PHY", + .probe = at803x_probe, + .suspend = at803x_suspend, + .resume = at803x_resume, + .flags = PHY_POLL_CABLE_TEST, + /* PHY_BASIC_FEATURES */ + .config_intr = at803x_config_intr, + .handle_interrupt = at803x_handle_interrupt, + .cable_test_start = at803x_cable_test_start, + .cable_test_get_status = at8032_cable_test_get_status, + .read_status = at803x_read_status, + .soft_reset = genphy_soft_reset, + .config_aneg = at803x_config_aneg, +}, }; + +module_phy_driver(at803x_driver); + +static struct mdio_device_id __maybe_unused atheros_tbl[] = { + { ATH8030_PHY_ID, AT8030_PHY_ID_MASK }, + { PHY_ID_MATCH_EXACT(ATH8031_PHY_ID) }, + { PHY_ID_MATCH_EXACT(ATH8032_PHY_ID) }, + { PHY_ID_MATCH_EXACT(ATH8035_PHY_ID) }, + { PHY_ID_MATCH_EXACT(ATH9331_PHY_ID) }, + { PHY_ID_MATCH_EXACT(QCA9561_PHY_ID) }, + { } +}; + +MODULE_DEVICE_TABLE(mdio, atheros_tbl); |