diff options
Diffstat (limited to 'drivers/pinctrl/samsung/pinctrl-samsung.h')
| -rw-r--r-- | drivers/pinctrl/samsung/pinctrl-samsung.h | 361 |
1 files changed, 361 insertions, 0 deletions
diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.h b/drivers/pinctrl/samsung/pinctrl-samsung.h new file mode 100644 index 0000000000..9af93e3d8d --- /dev/null +++ b/drivers/pinctrl/samsung/pinctrl-samsung.h @@ -0,0 +1,361 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * pin-controller/pin-mux/pin-config/gpio-driver for Samsung's SoC's. + * + * Copyright (c) 2012 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * Copyright (c) 2012 Linaro Ltd + * http://www.linaro.org + * + * Author: Thomas Abraham <thomas.ab@samsung.com> + */ + +#ifndef __PINCTRL_SAMSUNG_H +#define __PINCTRL_SAMSUNG_H + +#include <linux/pinctrl/pinctrl.h> +#include <linux/pinctrl/pinmux.h> +#include <linux/pinctrl/pinconf.h> +#include <linux/pinctrl/consumer.h> +#include <linux/pinctrl/machine.h> + +#include <linux/gpio/driver.h> + +/** + * enum pincfg_type - possible pin configuration types supported. + * @PINCFG_TYPE_FUNC: Function configuration. + * @PINCFG_TYPE_DAT: Pin value configuration. + * @PINCFG_TYPE_PUD: Pull up/down configuration. + * @PINCFG_TYPE_DRV: Drive strength configuration. + * @PINCFG_TYPE_CON_PDN: Pin function in power down mode. + * @PINCFG_TYPE_PUD_PDN: Pull up/down configuration in power down mode. + */ +enum pincfg_type { + PINCFG_TYPE_FUNC, + PINCFG_TYPE_DAT, + PINCFG_TYPE_PUD, + PINCFG_TYPE_DRV, + PINCFG_TYPE_CON_PDN, + PINCFG_TYPE_PUD_PDN, + + PINCFG_TYPE_NUM +}; + +/* + * pin configuration (pull up/down and drive strength) type and its value are + * packed together into a 16-bits. The upper 8-bits represent the configuration + * type and the lower 8-bits hold the value of the configuration type. + */ +#define PINCFG_TYPE_MASK 0xFF +#define PINCFG_VALUE_SHIFT 8 +#define PINCFG_VALUE_MASK (0xFF << PINCFG_VALUE_SHIFT) +#define PINCFG_PACK(type, value) (((value) << PINCFG_VALUE_SHIFT) | type) +#define PINCFG_UNPACK_TYPE(cfg) ((cfg) & PINCFG_TYPE_MASK) +#define PINCFG_UNPACK_VALUE(cfg) (((cfg) & PINCFG_VALUE_MASK) >> \ + PINCFG_VALUE_SHIFT) +/* + * Values for the pin CON register, choosing pin function. + * The basic set (input and output) are same between: S3C24xx, S3C64xx, S5PV210, + * Exynos ARMv7, Exynos ARMv8, Tesla FSD. + */ +#define PIN_CON_FUNC_INPUT 0x0 +#define PIN_CON_FUNC_OUTPUT 0x1 + +/** + * enum eint_type - possible external interrupt types. + * @EINT_TYPE_NONE: bank does not support external interrupts + * @EINT_TYPE_GPIO: bank supportes external gpio interrupts + * @EINT_TYPE_WKUP: bank supportes external wakeup interrupts + * @EINT_TYPE_WKUP_MUX: bank supports multiplexed external wakeup interrupts + * + * Samsung GPIO controller groups all the available pins into banks. The pins + * in a pin bank can support external gpio interrupts or external wakeup + * interrupts or no interrupts at all. From a software perspective, the only + * difference between external gpio and external wakeup interrupts is that + * the wakeup interrupts can additionally wakeup the system if it is in + * suspended state. + */ +enum eint_type { + EINT_TYPE_NONE, + EINT_TYPE_GPIO, + EINT_TYPE_WKUP, + EINT_TYPE_WKUP_MUX, +}; + +/* maximum length of a pin in pin descriptor (example: "gpa0-0") */ +#define PIN_NAME_LENGTH 10 + +#define PIN_GROUP(n, p, f) \ + { \ + .name = n, \ + .pins = p, \ + .num_pins = ARRAY_SIZE(p), \ + .func = f \ + } + +#define PMX_FUNC(n, g) \ + { \ + .name = n, \ + .groups = g, \ + .num_groups = ARRAY_SIZE(g), \ + } + +struct samsung_pinctrl_drv_data; + +/** + * struct samsung_pin_bank_type: pin bank type description + * @fld_width: widths of configuration bitfields (0 if unavailable) + * @reg_offset: offsets of configuration registers (don't care of width is 0) + */ +struct samsung_pin_bank_type { + u8 fld_width[PINCFG_TYPE_NUM]; + u8 reg_offset[PINCFG_TYPE_NUM]; +}; + +/** + * struct samsung_pin_bank_data: represent a controller pin-bank (init data). + * @type: type of the bank (register offsets and bitfield widths) + * @pctl_offset: starting offset of the pin-bank registers. + * @pctl_res_idx: index of base address for pin-bank registers. + * @nr_pins: number of pins included in this bank. + * @eint_func: function to set in CON register to configure pin as EINT. + * @eint_type: type of the external interrupt supported by the bank. + * @eint_mask: bit mask of pins which support EINT function. + * @eint_offset: SoC-specific EINT register or interrupt offset of bank. + * @name: name to be prefixed for each pin in this pin bank. + */ +struct samsung_pin_bank_data { + const struct samsung_pin_bank_type *type; + u32 pctl_offset; + u8 pctl_res_idx; + u8 nr_pins; + u8 eint_func; + enum eint_type eint_type; + u32 eint_mask; + u32 eint_offset; + const char *name; +}; + +/** + * struct samsung_pin_bank: represent a controller pin-bank. + * @type: type of the bank (register offsets and bitfield widths) + * @pctl_base: base address of the pin-bank registers + * @pctl_offset: starting offset of the pin-bank registers. + * @nr_pins: number of pins included in this bank. + * @eint_base: base address of the pin-bank EINT registers. + * @eint_func: function to set in CON register to configure pin as EINT. + * @eint_type: type of the external interrupt supported by the bank. + * @eint_mask: bit mask of pins which support EINT function. + * @eint_offset: SoC-specific EINT register or interrupt offset of bank. + * @name: name to be prefixed for each pin in this pin bank. + * @pin_base: starting pin number of the bank. + * @soc_priv: per-bank private data for SoC-specific code. + * @of_node: OF node of the bank. + * @drvdata: link to controller driver data + * @irq_domain: IRQ domain of the bank. + * @gpio_chip: GPIO chip of the bank. + * @grange: linux gpio pin range supported by this bank. + * @irq_chip: link to irq chip for external gpio and wakeup interrupts. + * @slock: spinlock protecting bank registers + * @pm_save: saved register values during suspend + */ +struct samsung_pin_bank { + const struct samsung_pin_bank_type *type; + void __iomem *pctl_base; + u32 pctl_offset; + u8 nr_pins; + void __iomem *eint_base; + u8 eint_func; + enum eint_type eint_type; + u32 eint_mask; + u32 eint_offset; + const char *name; + + u32 pin_base; + void *soc_priv; + struct fwnode_handle *fwnode; + struct samsung_pinctrl_drv_data *drvdata; + struct irq_domain *irq_domain; + struct gpio_chip gpio_chip; + struct pinctrl_gpio_range grange; + struct exynos_irq_chip *irq_chip; + raw_spinlock_t slock; + + u32 pm_save[PINCFG_TYPE_NUM + 1]; /* +1 to handle double CON registers*/ +}; + +/** + * struct samsung_retention_data: runtime pin-bank retention control data. + * @regs: array of PMU registers to control pad retention. + * @nr_regs: number of registers in @regs array. + * @value: value to store to registers to turn off retention. + * @refcnt: atomic counter if retention control affects more than one bank. + * @priv: retention control code private data + * @enable: platform specific callback to enter retention mode. + * @disable: platform specific callback to exit retention mode. + **/ +struct samsung_retention_ctrl { + const u32 *regs; + int nr_regs; + u32 value; + atomic_t *refcnt; + void *priv; + void (*enable)(struct samsung_pinctrl_drv_data *); + void (*disable)(struct samsung_pinctrl_drv_data *); +}; + +/** + * struct samsung_retention_data: represent a pin-bank retention control data. + * @regs: array of PMU registers to control pad retention. + * @nr_regs: number of registers in @regs array. + * @value: value to store to registers to turn off retention. + * @refcnt: atomic counter if retention control affects more than one bank. + * @init: platform specific callback to initialize retention control. + **/ +struct samsung_retention_data { + const u32 *regs; + int nr_regs; + u32 value; + atomic_t *refcnt; + struct samsung_retention_ctrl *(*init)(struct samsung_pinctrl_drv_data *, + const struct samsung_retention_data *); +}; + +/** + * struct samsung_pin_ctrl: represent a pin controller. + * @pin_banks: list of pin banks included in this controller. + * @nr_banks: number of pin banks. + * @nr_ext_resources: number of the extra base address for pin banks. + * @retention_data: configuration data for retention control. + * @eint_gpio_init: platform specific callback to setup the external gpio + * interrupts for the controller. + * @eint_wkup_init: platform specific callback to setup the external wakeup + * interrupts for the controller. + * @suspend: platform specific suspend callback, executed during pin controller + * device suspend, see samsung_pinctrl_suspend() + * @resume: platform specific resume callback, executed during pin controller + * device suspend, see samsung_pinctrl_resume() + * + * External wakeup interrupts must define at least eint_wkup_init, + * retention_data and suspend in order for proper suspend/resume to work. + */ +struct samsung_pin_ctrl { + const struct samsung_pin_bank_data *pin_banks; + unsigned int nr_banks; + unsigned int nr_ext_resources; + const struct samsung_retention_data *retention_data; + + int (*eint_gpio_init)(struct samsung_pinctrl_drv_data *); + int (*eint_wkup_init)(struct samsung_pinctrl_drv_data *); + void (*suspend)(struct samsung_pinctrl_drv_data *); + void (*resume)(struct samsung_pinctrl_drv_data *); +}; + +/** + * struct samsung_pinctrl_drv_data: wrapper for holding driver data together. + * @node: global list node + * @virt_base: register base address of the controller; this will be equal + * to each bank samsung_pin_bank->pctl_base and used on legacy + * platforms (like S3C24XX or S3C64XX) which has to access the base + * through samsung_pinctrl_drv_data, not samsung_pin_bank). + * @dev: device instance representing the controller. + * @irq: interrpt number used by the controller to notify gpio interrupts. + * @ctrl: pin controller instance managed by the driver. + * @pctl: pin controller descriptor registered with the pinctrl subsystem. + * @pctl_dev: cookie representing pinctrl device instance. + * @pin_groups: list of pin groups available to the driver. + * @nr_groups: number of such pin groups. + * @pmx_functions: list of pin functions available to the driver. + * @nr_function: number of such pin functions. + * @pin_base: starting system wide pin number. + * @nr_pins: number of pins supported by the controller. + * @retention_ctrl: retention control runtime data. + * @suspend: platform specific suspend callback, executed during pin controller + * device suspend, see samsung_pinctrl_suspend() + * @resume: platform specific resume callback, executed during pin controller + * device suspend, see samsung_pinctrl_resume() + */ +struct samsung_pinctrl_drv_data { + struct list_head node; + void __iomem *virt_base; + struct device *dev; + int irq; + + struct pinctrl_desc pctl; + struct pinctrl_dev *pctl_dev; + + const struct samsung_pin_group *pin_groups; + unsigned int nr_groups; + const struct samsung_pmx_func *pmx_functions; + unsigned int nr_functions; + + struct samsung_pin_bank *pin_banks; + unsigned int nr_banks; + unsigned int pin_base; + unsigned int nr_pins; + + struct samsung_retention_ctrl *retention_ctrl; + + void (*suspend)(struct samsung_pinctrl_drv_data *); + void (*resume)(struct samsung_pinctrl_drv_data *); +}; + +/** + * struct samsung_pinctrl_of_match_data: OF match device specific configuration data. + * @ctrl: array of pin controller data. + * @num_ctrl: size of array @ctrl. + */ +struct samsung_pinctrl_of_match_data { + const struct samsung_pin_ctrl *ctrl; + unsigned int num_ctrl; +}; + +/** + * struct samsung_pin_group: represent group of pins of a pinmux function. + * @name: name of the pin group, used to lookup the group. + * @pins: the pins included in this group. + * @num_pins: number of pins included in this group. + * @func: the function number to be programmed when selected. + */ +struct samsung_pin_group { + const char *name; + const unsigned int *pins; + u8 num_pins; + u8 func; +}; + +/** + * struct samsung_pmx_func: represent a pin function. + * @name: name of the pin function, used to lookup the function. + * @groups: one or more names of pin groups that provide this function. + * @num_groups: number of groups included in @groups. + */ +struct samsung_pmx_func { + const char *name; + const char **groups; + u8 num_groups; + u32 val; +}; + +/* list of all exported SoC specific data */ +extern const struct samsung_pinctrl_of_match_data exynos3250_of_data; +extern const struct samsung_pinctrl_of_match_data exynos4210_of_data; +extern const struct samsung_pinctrl_of_match_data exynos4x12_of_data; +extern const struct samsung_pinctrl_of_match_data exynos5250_of_data; +extern const struct samsung_pinctrl_of_match_data exynos5260_of_data; +extern const struct samsung_pinctrl_of_match_data exynos5410_of_data; +extern const struct samsung_pinctrl_of_match_data exynos5420_of_data; +extern const struct samsung_pinctrl_of_match_data exynos5433_of_data; +extern const struct samsung_pinctrl_of_match_data exynos7_of_data; +extern const struct samsung_pinctrl_of_match_data exynos7885_of_data; +extern const struct samsung_pinctrl_of_match_data exynos850_of_data; +extern const struct samsung_pinctrl_of_match_data exynosautov9_of_data; +extern const struct samsung_pinctrl_of_match_data fsd_of_data; +extern const struct samsung_pinctrl_of_match_data s3c64xx_of_data; +extern const struct samsung_pinctrl_of_match_data s3c2412_of_data; +extern const struct samsung_pinctrl_of_match_data s3c2416_of_data; +extern const struct samsung_pinctrl_of_match_data s3c2440_of_data; +extern const struct samsung_pinctrl_of_match_data s3c2450_of_data; +extern const struct samsung_pinctrl_of_match_data s5pv210_of_data; + +#endif /* __PINCTRL_SAMSUNG_H */ |