diff options
Diffstat (limited to 'drivers/soc/qcom/spm.c')
| -rw-r--r-- | drivers/soc/qcom/spm.c | 248 |
1 files changed, 244 insertions, 4 deletions
diff --git a/drivers/soc/qcom/spm.c b/drivers/soc/qcom/spm.c index 2f0b1bfe76..06e2c4c2a4 100644 --- a/drivers/soc/qcom/spm.c +++ b/drivers/soc/qcom/spm.c @@ -6,20 +6,40 @@ * SAW power controller driver */ -#include <linux/kernel.h> +#include <linux/bitfield.h> +#include <linux/err.h> #include <linux/init.h> #include <linux/io.h> +#include <linux/iopoll.h> +#include <linux/kernel.h> +#include <linux/linear_range.h> #include <linux/module.h> -#include <linux/slab.h> #include <linux/of.h> -#include <linux/err.h> #include <linux/platform_device.h> +#include <linux/slab.h> +#include <linux/smp.h> + +#include <linux/regulator/driver.h> + #include <soc/qcom/spm.h> +#define FIELD_SET(current, mask, val) \ + (((current) & ~(mask)) | FIELD_PREP((mask), (val))) + #define SPM_CTL_INDEX 0x7f #define SPM_CTL_INDEX_SHIFT 4 #define SPM_CTL_EN BIT(0) +/* These registers might be specific to SPM 1.1 */ +#define SPM_VCTL_VLVL GENMASK(7, 0) +#define SPM_PMIC_DATA_0_VLVL GENMASK(7, 0) +#define SPM_PMIC_DATA_1_MIN_VSEL GENMASK(5, 0) +#define SPM_PMIC_DATA_1_MAX_VSEL GENMASK(21, 16) + +#define SPM_1_1_AVS_CTL_AVS_ENABLED BIT(27) +#define SPM_AVS_CTL_MAX_VLVL GENMASK(22, 17) +#define SPM_AVS_CTL_MIN_VLVL GENMASK(15, 10) + enum spm_reg { SPM_REG_CFG, SPM_REG_SPM_CTL, @@ -29,13 +49,44 @@ enum spm_reg { SPM_REG_PMIC_DATA_1, SPM_REG_VCTL, SPM_REG_SEQ_ENTRY, - SPM_REG_SPM_STS, + SPM_REG_STS0, + SPM_REG_STS1, SPM_REG_PMIC_STS, SPM_REG_AVS_CTL, SPM_REG_AVS_LIMIT, + SPM_REG_RST, SPM_REG_NR, }; +#define MAX_PMIC_DATA 2 +#define MAX_SEQ_DATA 64 + +struct spm_reg_data { + const u16 *reg_offset; + u32 spm_cfg; + u32 spm_dly; + u32 pmic_dly; + u32 pmic_data[MAX_PMIC_DATA]; + u32 avs_ctl; + u32 avs_limit; + u8 seq[MAX_SEQ_DATA]; + u8 start_index[PM_SLEEP_MODE_NR]; + + smp_call_func_t set_vdd; + /* for now we support only a single range */ + struct linear_range *range; + unsigned int ramp_delay; + unsigned int init_uV; +}; + +struct spm_driver_data { + void __iomem *reg_base; + const struct spm_reg_data *reg_data; + struct device *dev; + unsigned int volt_sel; + int reg_cpu; +}; + static const u16 spm_reg_offset_v4_1[SPM_REG_NR] = { [SPM_REG_AVS_CTL] = 0x904, [SPM_REG_AVS_LIMIT] = 0x908, @@ -169,6 +220,10 @@ static const struct spm_reg_data spm_reg_8226_cpu = { static const u16 spm_reg_offset_v1_1[SPM_REG_NR] = { [SPM_REG_CFG] = 0x08, + [SPM_REG_STS0] = 0x0c, + [SPM_REG_STS1] = 0x10, + [SPM_REG_VCTL] = 0x14, + [SPM_REG_AVS_CTL] = 0x18, [SPM_REG_SPM_CTL] = 0x20, [SPM_REG_PMIC_DLY] = 0x24, [SPM_REG_PMIC_DATA_0] = 0x28, @@ -176,7 +231,12 @@ static const u16 spm_reg_offset_v1_1[SPM_REG_NR] = { [SPM_REG_SEQ_ENTRY] = 0x80, }; +static void smp_set_vdd_v1_1(void *data); + /* SPM register data for 8064 */ +static struct linear_range spm_v1_1_regulator_range = + REGULATOR_LINEAR_RANGE(700000, 0, 56, 12500); + static const struct spm_reg_data spm_reg_8064_cpu = { .reg_offset = spm_reg_offset_v1_1, .spm_cfg = 0x1F, @@ -187,6 +247,10 @@ static const struct spm_reg_data spm_reg_8064_cpu = { 0x10, 0x54, 0x30, 0x0C, 0x24, 0x30, 0x0F }, .start_index[PM_SLEEP_MODE_STBY] = 0, .start_index[PM_SLEEP_MODE_SPC] = 2, + .set_vdd = smp_set_vdd_v1_1, + .range = &spm_v1_1_regulator_range, + .init_uV = 1300000, + .ramp_delay = 1250, }; static inline void spm_register_write(struct spm_driver_data *drv, @@ -238,6 +302,178 @@ void spm_set_low_power_mode(struct spm_driver_data *drv, spm_register_write_sync(drv, SPM_REG_SPM_CTL, ctl_val); } +static int spm_set_voltage_sel(struct regulator_dev *rdev, unsigned int selector) +{ + struct spm_driver_data *drv = rdev_get_drvdata(rdev); + + drv->volt_sel = selector; + + /* Always do the SAW register writes on the corresponding CPU */ + return smp_call_function_single(drv->reg_cpu, drv->reg_data->set_vdd, drv, true); +} + +static int spm_get_voltage_sel(struct regulator_dev *rdev) +{ + struct spm_driver_data *drv = rdev_get_drvdata(rdev); + + return drv->volt_sel; +} + +static const struct regulator_ops spm_reg_ops = { + .set_voltage_sel = spm_set_voltage_sel, + .get_voltage_sel = spm_get_voltage_sel, + .list_voltage = regulator_list_voltage_linear_range, + .set_voltage_time_sel = regulator_set_voltage_time_sel, +}; + +static void smp_set_vdd_v1_1(void *data) +{ + struct spm_driver_data *drv = data; + unsigned int vctl, data0, data1, avs_ctl, sts; + unsigned int vlevel, volt_sel; + bool avs_enabled; + + volt_sel = drv->volt_sel; + vlevel = volt_sel | 0x80; /* band */ + + avs_ctl = spm_register_read(drv, SPM_REG_AVS_CTL); + vctl = spm_register_read(drv, SPM_REG_VCTL); + data0 = spm_register_read(drv, SPM_REG_PMIC_DATA_0); + data1 = spm_register_read(drv, SPM_REG_PMIC_DATA_1); + + avs_enabled = avs_ctl & SPM_1_1_AVS_CTL_AVS_ENABLED; + + /* If AVS is enabled, switch it off during the voltage change */ + if (avs_enabled) { + avs_ctl &= ~SPM_1_1_AVS_CTL_AVS_ENABLED; + spm_register_write(drv, SPM_REG_AVS_CTL, avs_ctl); + } + + /* Kick the state machine back to idle */ + spm_register_write(drv, SPM_REG_RST, 1); + + vctl = FIELD_SET(vctl, SPM_VCTL_VLVL, vlevel); + data0 = FIELD_SET(data0, SPM_PMIC_DATA_0_VLVL, vlevel); + data1 = FIELD_SET(data1, SPM_PMIC_DATA_1_MIN_VSEL, volt_sel); + data1 = FIELD_SET(data1, SPM_PMIC_DATA_1_MAX_VSEL, volt_sel); + + spm_register_write(drv, SPM_REG_VCTL, vctl); + spm_register_write(drv, SPM_REG_PMIC_DATA_0, data0); + spm_register_write(drv, SPM_REG_PMIC_DATA_1, data1); + + if (read_poll_timeout_atomic(spm_register_read, + sts, sts == vlevel, + 1, 200, false, + drv, SPM_REG_STS1)) { + dev_err_ratelimited(drv->dev, "timeout setting the voltage (%x %x)!\n", sts, vlevel); + goto enable_avs; + } + + if (avs_enabled) { + unsigned int max_avs = volt_sel; + unsigned int min_avs = max(max_avs, 4U) - 4; + + avs_ctl = FIELD_SET(avs_ctl, SPM_AVS_CTL_MIN_VLVL, min_avs); + avs_ctl = FIELD_SET(avs_ctl, SPM_AVS_CTL_MAX_VLVL, max_avs); + spm_register_write(drv, SPM_REG_AVS_CTL, avs_ctl); + } + +enable_avs: + if (avs_enabled) { + avs_ctl |= SPM_1_1_AVS_CTL_AVS_ENABLED; + spm_register_write(drv, SPM_REG_AVS_CTL, avs_ctl); + } +} + +static int spm_get_cpu(struct device *dev) +{ + int cpu; + bool found; + + for_each_possible_cpu(cpu) { + struct device_node *cpu_node, *saw_node; + + cpu_node = of_cpu_device_node_get(cpu); + if (!cpu_node) + continue; + + saw_node = of_parse_phandle(cpu_node, "qcom,saw", 0); + found = (saw_node == dev->of_node); + of_node_put(saw_node); + of_node_put(cpu_node); + + if (found) + return cpu; + } + + /* L2 SPM is not bound to any CPU, voltage setting is not supported */ + + return -EOPNOTSUPP; +} + +static int spm_register_regulator(struct device *dev, struct spm_driver_data *drv) +{ + struct regulator_config config = { + .dev = dev, + .driver_data = drv, + }; + struct regulator_desc *rdesc; + struct regulator_dev *rdev; + int ret; + bool found; + + if (!drv->reg_data->set_vdd) + return 0; + + rdesc = devm_kzalloc(dev, sizeof(*rdesc), GFP_KERNEL); + if (!rdesc) + return -ENOMEM; + + rdesc->name = "spm"; + rdesc->of_match = of_match_ptr("regulator"); + rdesc->type = REGULATOR_VOLTAGE; + rdesc->owner = THIS_MODULE; + rdesc->ops = &spm_reg_ops; + + rdesc->linear_ranges = drv->reg_data->range; + rdesc->n_linear_ranges = 1; + rdesc->n_voltages = rdesc->linear_ranges[rdesc->n_linear_ranges - 1].max_sel + 1; + rdesc->ramp_delay = drv->reg_data->ramp_delay; + + ret = spm_get_cpu(dev); + if (ret < 0) + return ret; + + drv->reg_cpu = ret; + dev_dbg(dev, "SAW2 bound to CPU %d\n", drv->reg_cpu); + + /* + * Program initial voltage, otherwise registration will also try + * setting the voltage, which might result in undervolting the CPU. + */ + drv->volt_sel = DIV_ROUND_UP(drv->reg_data->init_uV - rdesc->min_uV, + rdesc->uV_step); + ret = linear_range_get_selector_high(drv->reg_data->range, + drv->reg_data->init_uV, + &drv->volt_sel, + &found); + if (ret) { + dev_err(dev, "Initial uV value out of bounds\n"); + return ret; + } + + /* Always do the SAW register writes on the corresponding CPU */ + smp_call_function_single(drv->reg_cpu, drv->reg_data->set_vdd, drv, true); + + rdev = devm_regulator_register(dev, rdesc, &config); + if (IS_ERR(rdev)) { + dev_err(dev, "failed to register regulator\n"); + return PTR_ERR(rdev); + } + + return 0; +} + static const struct of_device_id spm_match_table[] = { { .compatible = "qcom,sdm660-gold-saw2-v4.1-l2", .data = &spm_reg_660_gold_l2 }, @@ -288,6 +524,7 @@ static int spm_dev_probe(struct platform_device *pdev) return -ENODEV; drv->reg_data = match_id->data; + drv->dev = &pdev->dev; platform_set_drvdata(pdev, drv); /* Write the SPM sequences first.. */ @@ -315,6 +552,9 @@ static int spm_dev_probe(struct platform_device *pdev) if (drv->reg_data->reg_offset[SPM_REG_SPM_CTL]) spm_set_low_power_mode(drv, PM_SLEEP_MODE_STBY); + if (IS_ENABLED(CONFIG_REGULATOR)) + return spm_register_regulator(&pdev->dev, drv); + return 0; } |