summaryrefslogtreecommitdiffstats
path: root/drivers/tty
diff options
context:
space:
mode:
Diffstat (limited to '')
-rw-r--r--drivers/tty/mxser.c2
-rw-r--r--drivers/tty/serial/8250/8250_omap.c22
-rw-r--r--drivers/tty/serial/8250/8250_pci.c13
-rw-r--r--drivers/tty/serial/bcm63xx_uart.c7
-rw-r--r--drivers/tty/serial/imx.c10
-rw-r--r--drivers/tty/serial/mcf.c2
6 files changed, 46 insertions, 10 deletions
diff --git a/drivers/tty/mxser.c b/drivers/tty/mxser.c
index 458bb1280e..5b97e420a9 100644
--- a/drivers/tty/mxser.c
+++ b/drivers/tty/mxser.c
@@ -288,7 +288,7 @@ struct mxser_board {
enum mxser_must_hwid must_hwid;
speed_t max_baud;
- struct mxser_port ports[] __counted_by(nports);
+ struct mxser_port ports[] /* __counted_by(nports) */;
};
static DECLARE_BITMAP(mxser_boards, MXSER_BOARDS);
diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c
index 66901d9308..ddf23ccbc9 100644
--- a/drivers/tty/serial/8250/8250_omap.c
+++ b/drivers/tty/serial/8250/8250_omap.c
@@ -116,6 +116,10 @@
/* RX FIFO occupancy indicator */
#define UART_OMAP_RX_LVL 0x19
+/* Timeout low and High */
+#define UART_OMAP_TO_L 0x26
+#define UART_OMAP_TO_H 0x27
+
/*
* Copy of the genpd flags for the console.
* Only used if console suspend is disabled
@@ -664,13 +668,25 @@ static irqreturn_t omap8250_irq(int irq, void *dev_id)
/*
* On K3 SoCs, it is observed that RX TIMEOUT is signalled after
- * FIFO has been drained, in which case a dummy read of RX FIFO
- * is required to clear RX TIMEOUT condition.
+ * FIFO has been drained or erroneously.
+ * So apply solution of Errata i2310 as mentioned in
+ * https://www.ti.com/lit/pdf/sprz536
*/
if (priv->habit & UART_RX_TIMEOUT_QUIRK &&
(iir & UART_IIR_RX_TIMEOUT) == UART_IIR_RX_TIMEOUT &&
serial_port_in(port, UART_OMAP_RX_LVL) == 0) {
- serial_port_in(port, UART_RX);
+ unsigned char efr2, timeout_h, timeout_l;
+
+ efr2 = serial_in(up, UART_OMAP_EFR2);
+ timeout_h = serial_in(up, UART_OMAP_TO_H);
+ timeout_l = serial_in(up, UART_OMAP_TO_L);
+ serial_out(up, UART_OMAP_TO_H, 0xFF);
+ serial_out(up, UART_OMAP_TO_L, 0xFF);
+ serial_out(up, UART_OMAP_EFR2, UART_OMAP_EFR2_TIMEOUT_BEHAVE);
+ serial_in(up, UART_IIR);
+ serial_out(up, UART_OMAP_EFR2, efr2);
+ serial_out(up, UART_OMAP_TO_H, timeout_h);
+ serial_out(up, UART_OMAP_TO_L, timeout_l);
}
/* Stop processing interrupts on input overrun */
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index e2e4f99f9d..fe0fb2b4e9 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1985,6 +1985,17 @@ enum {
MOXA_SUPP_RS485 = BIT(2),
};
+static unsigned short moxa_get_nports(unsigned short device)
+{
+ switch (device) {
+ case PCI_DEVICE_ID_MOXA_CP116E_A_A:
+ case PCI_DEVICE_ID_MOXA_CP116E_A_B:
+ return 8;
+ }
+
+ return FIELD_GET(0x00F0, device);
+}
+
static bool pci_moxa_is_mini_pcie(unsigned short device)
{
if (device == PCI_DEVICE_ID_MOXA_CP102N ||
@@ -2038,7 +2049,7 @@ static int pci_moxa_init(struct pci_dev *dev)
{
unsigned short device = dev->device;
resource_size_t iobar_addr = pci_resource_start(dev, 2);
- unsigned int num_ports = (device & 0x00F0) >> 4, i;
+ unsigned int i, num_ports = moxa_get_nports(device);
u8 val, init_mode = MOXA_RS232;
if (!(pci_moxa_supported_rs(dev) & MOXA_SUPP_RS232)) {
diff --git a/drivers/tty/serial/bcm63xx_uart.c b/drivers/tty/serial/bcm63xx_uart.c
index 34801a6f30..b88cc28c94 100644
--- a/drivers/tty/serial/bcm63xx_uart.c
+++ b/drivers/tty/serial/bcm63xx_uart.c
@@ -308,8 +308,8 @@ static void bcm_uart_do_tx(struct uart_port *port)
val = bcm_uart_readl(port, UART_MCTL_REG);
val = (val & UART_MCTL_TXFIFOFILL_MASK) >> UART_MCTL_TXFIFOFILL_SHIFT;
-
- pending = uart_port_tx_limited(port, ch, port->fifosize - val,
+ pending = uart_port_tx_limited_flags(port, ch, UART_TX_NOSTOP,
+ port->fifosize - val,
true,
bcm_uart_writel(port, ch, UART_FIFO_REG),
({}));
@@ -320,6 +320,9 @@ static void bcm_uart_do_tx(struct uart_port *port)
val = bcm_uart_readl(port, UART_IR_REG);
val &= ~UART_TX_INT_MASK;
bcm_uart_writel(port, val, UART_IR_REG);
+
+ if (uart_tx_stopped(port))
+ bcm_uart_stop_tx(port);
}
/*
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 09c1678ddf..9552228d21 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -119,6 +119,7 @@
#define UCR4_OREN (1<<1) /* Receiver overrun interrupt enable */
#define UCR4_DREN (1<<0) /* Recv data ready interrupt enable */
#define UFCR_RXTL_SHF 0 /* Receiver trigger level shift */
+#define UFCR_RXTL_MASK 0x3F /* Receiver trigger 6 bits wide */
#define UFCR_DCEDTE (1<<6) /* DCE/DTE mode select */
#define UFCR_RFDIV (7<<7) /* Reference freq divider mask */
#define UFCR_RFDIV_REG(x) (((x) < 7 ? 6 - (x) : 6) << 7)
@@ -1941,7 +1942,7 @@ static int imx_uart_rs485_config(struct uart_port *port, struct ktermios *termio
struct serial_rs485 *rs485conf)
{
struct imx_port *sport = (struct imx_port *)port;
- u32 ucr2;
+ u32 ucr2, ufcr;
if (rs485conf->flags & SER_RS485_ENABLED) {
/* Enable receiver if low-active RTS signal is requested */
@@ -1960,8 +1961,13 @@ static int imx_uart_rs485_config(struct uart_port *port, struct ktermios *termio
/* Make sure Rx is enabled in case Tx is active with Rx disabled */
if (!(rs485conf->flags & SER_RS485_ENABLED) ||
- rs485conf->flags & SER_RS485_RX_DURING_TX)
+ rs485conf->flags & SER_RS485_RX_DURING_TX) {
+ /* If the receiver trigger is 0, set it to a default value */
+ ufcr = imx_uart_readl(sport, UFCR);
+ if ((ufcr & UFCR_RXTL_MASK) == 0)
+ imx_uart_setup_ufcr(sport, TXTL_DEFAULT, RXTL_DEFAULT);
imx_uart_start_rx(port);
+ }
return 0;
}
diff --git a/drivers/tty/serial/mcf.c b/drivers/tty/serial/mcf.c
index b0604d6da0..58858dd352 100644
--- a/drivers/tty/serial/mcf.c
+++ b/drivers/tty/serial/mcf.c
@@ -462,7 +462,7 @@ static const struct uart_ops mcf_uart_ops = {
.verify_port = mcf_verify_port,
};
-static struct mcf_uart mcf_ports[4];
+static struct mcf_uart mcf_ports[10];
#define MCF_MAXPORTS ARRAY_SIZE(mcf_ports)