diff options
Diffstat (limited to 'drivers/usb/phy/Kconfig')
| -rw-r--r-- | drivers/usb/phy/Kconfig | 175 |
1 files changed, 175 insertions, 0 deletions
diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig new file mode 100644 index 0000000000..5f629d7cad --- /dev/null +++ b/drivers/usb/phy/Kconfig @@ -0,0 +1,175 @@ +# SPDX-License-Identifier: GPL-2.0 +# +# Physical Layer USB driver configuration +# +menu "USB Physical Layer drivers" + +config USB_PHY + select EXTCON + def_bool n + +# +# USB Transceiver Drivers +# +config AB8500_USB + tristate "AB8500 USB Transceiver Driver" + depends on AB8500_CORE + select USB_PHY + help + Enable this to support the USB OTG transceiver in AB8500 chip. + This transceiver supports high and full speed devices plus, + in host mode, low speed. + +config FSL_USB2_OTG + tristate "Freescale USB OTG Transceiver Driver" + depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM=y && PM + depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' + select USB_PHY + help + Enable this to support Freescale USB OTG transceiver. + +config KEYSTONE_USB_PHY + tristate "Keystone USB PHY Driver" + depends on ARCH_KEYSTONE || COMPILE_TEST + depends on NOP_USB_XCEIV + help + Enable this to support Keystone USB phy. This driver provides + interface to interact with USB 2.0 and USB 3.0 PHY that is part + of the Keystone SOC. + +config NOP_USB_XCEIV + tristate "NOP USB Transceiver Driver" + depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, NOP can't be built-in + select USB_PHY + help + This driver is to be used by all the usb transceiver which are either + built-in with usb ip or which are autonomous and doesn't require any + phy programming such as ISP1x04 etc. + +config AM335X_CONTROL_USB + tristate + +config AM335X_PHY_USB + tristate "AM335x USB PHY Driver" + depends on ARM || COMPILE_TEST + depends on NOP_USB_XCEIV + select USB_PHY + select AM335X_CONTROL_USB + select USB_COMMON + help + This driver provides PHY support for that phy which part for the + AM335x SoC. + +config TWL6030_USB + tristate "TWL6030 USB Transceiver Driver" + depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS + depends on OF + help + Enable this to support the USB OTG transceiver on TWL6030 + family chips. This TWL6030 transceiver has the VBUS and ID GND + and OTG SRP events capabilities. For all other transceiver functionality + UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs + are hooked to this driver through platform_data structure. + The definition of internal PHY APIs are in the mach-omap2 layer. + +config USB_GPIO_VBUS + tristate "GPIO based peripheral-only VBUS sensing 'transceiver'" + depends on GPIOLIB || COMPILE_TEST + depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' + depends on !USB_CONN_GPIO + select USB_PHY + help + Provides simple GPIO VBUS sensing for controllers with an + internal transceiver via the usb_phy interface, and + optionally control of a D+ pullup GPIO as well as a VBUS + current limit regulator. This driver is for devices that do + NOT support role switch. OTG devices that can do role switch + (master/peripheral) shall use the USB based connection + detection driver USB_CONN_GPIO. + +config OMAP_OTG + tristate "OMAP USB OTG controller driver" + depends on ARCH_OMAP_OTG && EXTCON + help + Enable this to support some transceivers on OMAP1 platforms. OTG + controller is needed to switch between host and peripheral modes. + + This driver can also be built as a module. If so, the module + will be called phy-omap-otg. + +config TAHVO_USB + tristate "Tahvo USB transceiver driver" + depends on MFD_RETU + depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' + select USB_PHY + help + Enable this to support USB transceiver on Tahvo. This is used + at least on Nokia 770. + +config TAHVO_USB_HOST_BY_DEFAULT + depends on TAHVO_USB + bool "Device in USB host mode by default" + help + Say Y here, if you want the device to enter USB host mode + by default on bootup. + +config USB_ISP1301 + tristate "NXP ISP1301 USB transceiver support" + depends on USB || USB_GADGET + depends on I2C + select USB_PHY + help + Say Y here to add support for the NXP ISP1301 USB transceiver driver. + This chip is typically used as USB transceiver for USB host, gadget + and OTG drivers (to be selected separately). + + To compile this driver as a module, choose M here: the + module will be called phy-isp1301. + +config USB_MV_OTG + tristate "Marvell USB OTG support" + depends on USB_EHCI_MV && USB_MV_UDC && PM && USB_OTG + depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' + select USB_PHY + help + Say Y here if you want to build Marvell USB OTG transceiver + driver in kernel (including PXA and MMP series). This driver + implements role switch between EHCI host driver and gadget driver. + + To compile this driver as a module, choose M here. + +config USB_MXS_PHY + tristate "Freescale MXS USB PHY support" + depends on ARCH_MXC || ARCH_MXS + select STMP_DEVICE + select USB_PHY + help + Enable this to support the Freescale MXS USB PHY. + + MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x. + +config USB_TEGRA_PHY + tristate "NVIDIA Tegra USB PHY Driver" + depends on ARCH_TEGRA || COMPILE_TEST + select USB_COMMON + select USB_PHY + select USB_ULPI + help + This driver provides PHY support for the USB controllers found + on NVIDIA Tegra SoC's. + +config USB_ULPI + bool "Generic ULPI Transceiver Driver" + depends on ARM || ARM64 || COMPILE_TEST + select USB_ULPI_VIEWPORT + help + Enable this to support ULPI connected USB OTG transceivers which + are likely found on embedded boards. + +config USB_ULPI_VIEWPORT + bool + help + Provides read/write operations to the ULPI phy register set for + controllers with a viewport register (e.g. Chipidea/ARC controllers). + +endmenu |