diff options
Diffstat (limited to 'include/drm/gud.h')
| -rw-r--r-- | include/drm/gud.h | 335 |
1 files changed, 335 insertions, 0 deletions
diff --git a/include/drm/gud.h b/include/drm/gud.h new file mode 100644 index 0000000000..c52a8ba4ae --- /dev/null +++ b/include/drm/gud.h @@ -0,0 +1,335 @@ +/* SPDX-License-Identifier: MIT */ +/* + * Copyright 2020 Noralf Trønnes + */ + +#ifndef __LINUX_GUD_H +#define __LINUX_GUD_H + +#include <linux/types.h> + +/* + * struct gud_display_descriptor_req - Display descriptor + * @magic: Magic value GUD_DISPLAY_MAGIC + * @version: Protocol version + * @flags: Flags + * - STATUS_ON_SET: Always do a status request after a SET request. + * This is used by the Linux gadget driver since it has + * no way to control the status stage of a control OUT + * request that has a payload. + * - FULL_UPDATE: Always send the entire framebuffer when flushing changes. + * The GUD_REQ_SET_BUFFER request will not be sent + * before each bulk transfer, it will only be sent if the + * previous bulk transfer had failed. This gives the device + * a chance to reset its state machine if needed. + * This flag can not be used in combination with compression. + * @compression: Supported compression types + * - GUD_COMPRESSION_LZ4: LZ4 lossless compression. + * @max_buffer_size: Maximum buffer size the device can handle (optional). + * This is useful for devices that don't have a big enough + * buffer to decompress the entire framebuffer in one go. + * @min_width: Minimum pixel width the controller can handle + * @max_width: Maximum width + * @min_height: Minimum height + * @max_height: Maximum height + * + * Devices that have only one display mode will have min_width == max_width + * and min_height == max_height. + */ +struct gud_display_descriptor_req { + __le32 magic; +#define GUD_DISPLAY_MAGIC 0x1d50614d + __u8 version; + __le32 flags; +#define GUD_DISPLAY_FLAG_STATUS_ON_SET BIT(0) +#define GUD_DISPLAY_FLAG_FULL_UPDATE BIT(1) + __u8 compression; +#define GUD_COMPRESSION_LZ4 BIT(0) + __le32 max_buffer_size; + __le32 min_width; + __le32 max_width; + __le32 min_height; + __le32 max_height; +} __packed; + +/* + * struct gud_property_req - Property + * @prop: Property + * @val: Value + */ +struct gud_property_req { + __le16 prop; + __le64 val; +} __packed; + +/* + * struct gud_display_mode_req - Display mode + * @clock: Pixel clock in kHz + * @hdisplay: Horizontal display size + * @hsync_start: Horizontal sync start + * @hsync_end: Horizontal sync end + * @htotal: Horizontal total size + * @vdisplay: Vertical display size + * @vsync_start: Vertical sync start + * @vsync_end: Vertical sync end + * @vtotal: Vertical total size + * @flags: Bits 0-13 are the same as in the RandR protocol and also what DRM uses. + * The deprecated bits are reused for internal protocol flags leaving us + * free to follow DRM for the other bits in the future. + * - FLAG_PREFERRED: Set on the preferred display mode. + */ +struct gud_display_mode_req { + __le32 clock; + __le16 hdisplay; + __le16 hsync_start; + __le16 hsync_end; + __le16 htotal; + __le16 vdisplay; + __le16 vsync_start; + __le16 vsync_end; + __le16 vtotal; + __le32 flags; +#define GUD_DISPLAY_MODE_FLAG_PHSYNC BIT(0) +#define GUD_DISPLAY_MODE_FLAG_NHSYNC BIT(1) +#define GUD_DISPLAY_MODE_FLAG_PVSYNC BIT(2) +#define GUD_DISPLAY_MODE_FLAG_NVSYNC BIT(3) +#define GUD_DISPLAY_MODE_FLAG_INTERLACE BIT(4) +#define GUD_DISPLAY_MODE_FLAG_DBLSCAN BIT(5) +#define GUD_DISPLAY_MODE_FLAG_CSYNC BIT(6) +#define GUD_DISPLAY_MODE_FLAG_PCSYNC BIT(7) +#define GUD_DISPLAY_MODE_FLAG_NCSYNC BIT(8) +#define GUD_DISPLAY_MODE_FLAG_HSKEW BIT(9) +/* BCast and PixelMultiplex are deprecated */ +#define GUD_DISPLAY_MODE_FLAG_DBLCLK BIT(12) +#define GUD_DISPLAY_MODE_FLAG_CLKDIV2 BIT(13) +#define GUD_DISPLAY_MODE_FLAG_USER_MASK \ + (GUD_DISPLAY_MODE_FLAG_PHSYNC | GUD_DISPLAY_MODE_FLAG_NHSYNC | \ + GUD_DISPLAY_MODE_FLAG_PVSYNC | GUD_DISPLAY_MODE_FLAG_NVSYNC | \ + GUD_DISPLAY_MODE_FLAG_INTERLACE | GUD_DISPLAY_MODE_FLAG_DBLSCAN | \ + GUD_DISPLAY_MODE_FLAG_CSYNC | GUD_DISPLAY_MODE_FLAG_PCSYNC | \ + GUD_DISPLAY_MODE_FLAG_NCSYNC | GUD_DISPLAY_MODE_FLAG_HSKEW | \ + GUD_DISPLAY_MODE_FLAG_DBLCLK | GUD_DISPLAY_MODE_FLAG_CLKDIV2) +/* Internal protocol flags */ +#define GUD_DISPLAY_MODE_FLAG_PREFERRED BIT(10) +} __packed; + +/* + * struct gud_connector_descriptor_req - Connector descriptor + * @connector_type: Connector type (GUD_CONNECTOR_TYPE_*). + * If the host doesn't support the type it should fall back to PANEL. + * @flags: Flags + * - POLL_STATUS: Connector status can change (polled every 10 seconds) + * - INTERLACE: Interlaced modes are supported + * - DOUBLESCAN: Doublescan modes are supported + */ +struct gud_connector_descriptor_req { + __u8 connector_type; +#define GUD_CONNECTOR_TYPE_PANEL 0 +#define GUD_CONNECTOR_TYPE_VGA 1 +#define GUD_CONNECTOR_TYPE_COMPOSITE 2 +#define GUD_CONNECTOR_TYPE_SVIDEO 3 +#define GUD_CONNECTOR_TYPE_COMPONENT 4 +#define GUD_CONNECTOR_TYPE_DVI 5 +#define GUD_CONNECTOR_TYPE_DISPLAYPORT 6 +#define GUD_CONNECTOR_TYPE_HDMI 7 + __le32 flags; +#define GUD_CONNECTOR_FLAGS_POLL_STATUS BIT(0) +#define GUD_CONNECTOR_FLAGS_INTERLACE BIT(1) +#define GUD_CONNECTOR_FLAGS_DOUBLESCAN BIT(2) +} __packed; + +/* + * struct gud_set_buffer_req - Set buffer transfer info + * @x: X position of rectangle + * @y: Y position + * @width: Pixel width of rectangle + * @height: Pixel height + * @length: Buffer length in bytes + * @compression: Transfer compression + * @compressed_length: Compressed buffer length + * + * This request is issued right before the bulk transfer. + * @x, @y, @width and @height specifies the rectangle where the buffer should be + * placed inside the framebuffer. + */ +struct gud_set_buffer_req { + __le32 x; + __le32 y; + __le32 width; + __le32 height; + __le32 length; + __u8 compression; + __le32 compressed_length; +} __packed; + +/* + * struct gud_state_req - Display state + * @mode: Display mode + * @format: Pixel format GUD_PIXEL_FORMAT_* + * @connector: Connector index + * @properties: Array of properties + * + * The entire state is transferred each time there's a change. + */ +struct gud_state_req { + struct gud_display_mode_req mode; + __u8 format; + __u8 connector; + struct gud_property_req properties[]; +} __packed; + +/* List of supported connector properties: */ + +/* Margins in pixels to deal with overscan, range 0-100 */ +#define GUD_PROPERTY_TV_LEFT_MARGIN 1 +#define GUD_PROPERTY_TV_RIGHT_MARGIN 2 +#define GUD_PROPERTY_TV_TOP_MARGIN 3 +#define GUD_PROPERTY_TV_BOTTOM_MARGIN 4 +#define GUD_PROPERTY_TV_MODE 5 +/* Brightness in percent, range 0-100 */ +#define GUD_PROPERTY_TV_BRIGHTNESS 6 +/* Contrast in percent, range 0-100 */ +#define GUD_PROPERTY_TV_CONTRAST 7 +/* Flicker reduction in percent, range 0-100 */ +#define GUD_PROPERTY_TV_FLICKER_REDUCTION 8 +/* Overscan in percent, range 0-100 */ +#define GUD_PROPERTY_TV_OVERSCAN 9 +/* Saturation in percent, range 0-100 */ +#define GUD_PROPERTY_TV_SATURATION 10 +/* Hue in percent, range 0-100 */ +#define GUD_PROPERTY_TV_HUE 11 + +/* + * Backlight brightness is in the range 0-100 inclusive. The value represents the human perceptual + * brightness and not a linear PWM value. 0 is minimum brightness which should not turn the + * backlight completely off. The DPMS connector property should be used to control power which will + * trigger a GUD_REQ_SET_DISPLAY_ENABLE request. + * + * This does not map to a DRM property, it is used with the backlight device. + */ +#define GUD_PROPERTY_BACKLIGHT_BRIGHTNESS 12 + +/* List of supported properties that are not connector propeties: */ + +/* + * Plane rotation. Should return the supported bitmask on + * GUD_REQ_GET_PROPERTIES. GUD_ROTATION_0 is mandatory. + * + * Note: This is not display rotation so 90/270 will need scaling to make it fit (unless squared). + */ +#define GUD_PROPERTY_ROTATION 50 + #define GUD_ROTATION_0 BIT(0) + #define GUD_ROTATION_90 BIT(1) + #define GUD_ROTATION_180 BIT(2) + #define GUD_ROTATION_270 BIT(3) + #define GUD_ROTATION_REFLECT_X BIT(4) + #define GUD_ROTATION_REFLECT_Y BIT(5) + #define GUD_ROTATION_MASK (GUD_ROTATION_0 | GUD_ROTATION_90 | \ + GUD_ROTATION_180 | GUD_ROTATION_270 | \ + GUD_ROTATION_REFLECT_X | GUD_ROTATION_REFLECT_Y) + +/* USB Control requests: */ + +/* Get status from the last GET/SET control request. Value is u8. */ +#define GUD_REQ_GET_STATUS 0x00 + /* Status values: */ + #define GUD_STATUS_OK 0x00 + #define GUD_STATUS_BUSY 0x01 + #define GUD_STATUS_REQUEST_NOT_SUPPORTED 0x02 + #define GUD_STATUS_PROTOCOL_ERROR 0x03 + #define GUD_STATUS_INVALID_PARAMETER 0x04 + #define GUD_STATUS_ERROR 0x05 + +/* Get display descriptor as a &gud_display_descriptor_req */ +#define GUD_REQ_GET_DESCRIPTOR 0x01 + +/* Get supported pixel formats as a byte array of GUD_PIXEL_FORMAT_* */ +#define GUD_REQ_GET_FORMATS 0x40 + #define GUD_FORMATS_MAX_NUM 32 + #define GUD_PIXEL_FORMAT_R1 0x01 /* 1-bit monochrome */ + #define GUD_PIXEL_FORMAT_R8 0x08 /* 8-bit greyscale */ + #define GUD_PIXEL_FORMAT_XRGB1111 0x20 + #define GUD_PIXEL_FORMAT_RGB332 0x30 + #define GUD_PIXEL_FORMAT_RGB565 0x40 + #define GUD_PIXEL_FORMAT_RGB888 0x50 + #define GUD_PIXEL_FORMAT_XRGB8888 0x80 + #define GUD_PIXEL_FORMAT_ARGB8888 0x81 + +/* + * Get supported properties that are not connector propeties as a &gud_property_req array. + * gud_property_req.val often contains the initial value for the property. + */ +#define GUD_REQ_GET_PROPERTIES 0x41 + #define GUD_PROPERTIES_MAX_NUM 32 + +/* Connector requests have the connector index passed in the wValue field */ + +/* Get connector descriptors as an array of &gud_connector_descriptor_req */ +#define GUD_REQ_GET_CONNECTORS 0x50 + #define GUD_CONNECTORS_MAX_NUM 32 + +/* + * Get properties supported by the connector as a &gud_property_req array. + * gud_property_req.val often contains the initial value for the property. + */ +#define GUD_REQ_GET_CONNECTOR_PROPERTIES 0x51 + #define GUD_CONNECTOR_PROPERTIES_MAX_NUM 32 + +/* + * Issued when there's a TV_MODE property present. + * Gets an array of the supported TV_MODE names each entry of length + * GUD_CONNECTOR_TV_MODE_NAME_LEN. Names must be NUL-terminated. + */ +#define GUD_REQ_GET_CONNECTOR_TV_MODE_VALUES 0x52 + #define GUD_CONNECTOR_TV_MODE_NAME_LEN 16 + #define GUD_CONNECTOR_TV_MODE_MAX_NUM 16 + +/* When userspace checks connector status, this is issued first, not used for poll requests. */ +#define GUD_REQ_SET_CONNECTOR_FORCE_DETECT 0x53 + +/* + * Get connector status. Value is u8. + * + * Userspace will get a HOTPLUG uevent if one of the following is true: + * - Connection status has changed since last + * - CHANGED is set + */ +#define GUD_REQ_GET_CONNECTOR_STATUS 0x54 + #define GUD_CONNECTOR_STATUS_DISCONNECTED 0x00 + #define GUD_CONNECTOR_STATUS_CONNECTED 0x01 + #define GUD_CONNECTOR_STATUS_UNKNOWN 0x02 + #define GUD_CONNECTOR_STATUS_CONNECTED_MASK 0x03 + #define GUD_CONNECTOR_STATUS_CHANGED BIT(7) + +/* + * Display modes can be fetched as either EDID data or an array of &gud_display_mode_req. + * + * If GUD_REQ_GET_CONNECTOR_MODES returns zero, EDID is used to create display modes. + * If both display modes and EDID are returned, EDID is just passed on to userspace + * in the EDID connector property. + */ + +/* Get &gud_display_mode_req array of supported display modes */ +#define GUD_REQ_GET_CONNECTOR_MODES 0x55 + #define GUD_CONNECTOR_MAX_NUM_MODES 128 + +/* Get Extended Display Identification Data */ +#define GUD_REQ_GET_CONNECTOR_EDID 0x56 + #define GUD_CONNECTOR_MAX_EDID_LEN 2048 + +/* Set buffer properties before bulk transfer as &gud_set_buffer_req */ +#define GUD_REQ_SET_BUFFER 0x60 + +/* Check display configuration as &gud_state_req */ +#define GUD_REQ_SET_STATE_CHECK 0x61 + +/* Apply the previous STATE_CHECK configuration */ +#define GUD_REQ_SET_STATE_COMMIT 0x62 + +/* Enable/disable the display controller, value is u8: 0/1 */ +#define GUD_REQ_SET_CONTROLLER_ENABLE 0x63 + +/* Enable/disable display/output (DPMS), value is u8: 0/1 */ +#define GUD_REQ_SET_DISPLAY_ENABLE 0x64 + +#endif |