diff options
Diffstat (limited to 'sound/soc/tegra/Kconfig')
| -rw-r--r-- | sound/soc/tegra/Kconfig | 294 |
1 files changed, 294 insertions, 0 deletions
diff --git a/sound/soc/tegra/Kconfig b/sound/soc/tegra/Kconfig new file mode 100644 index 0000000000..74effc57a7 --- /dev/null +++ b/sound/soc/tegra/Kconfig @@ -0,0 +1,294 @@ +# SPDX-License-Identifier: GPL-2.0-only +config SND_SOC_TEGRA + tristate "SoC Audio for the Tegra System-on-Chip" + depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST + depends on COMMON_CLK + depends on RESET_CONTROLLER + select REGMAP_MMIO + select SND_SOC_GENERIC_DMAENGINE_PCM + help + Say Y or M here if you want support for SoC audio on Tegra. + +if SND_SOC_TEGRA + +config SND_SOC_TEGRA20_AC97 + tristate "Tegra20 AC97 interface" + select SND_SOC_AC97_BUS + select SND_SOC_TEGRA20_DAS + help + Say Y or M if you want to add support for codecs attached to the + Tegra20 AC97 interface. You will also need to select the individual + machine drivers to support below. + +config SND_SOC_TEGRA20_DAS + tristate "Tegra20 DAS module" + help + Say Y or M if you want to add support for the Tegra20 DAS module. + You will also need to select the individual machine drivers to + support below. + +config SND_SOC_TEGRA20_I2S + tristate "Tegra20 I2S interface" + select SND_SOC_TEGRA20_DAS + help + Say Y or M if you want to add support for codecs attached to the + Tegra20 I2S interface. You will also need to select the individual + machine drivers to support below. + +config SND_SOC_TEGRA20_SPDIF + tristate "Tegra20 SPDIF interface" + help + Say Y or M if you want to add support for the Tegra20 SPDIF interface. + You will also need to select the individual machine drivers to support + below. + +config SND_SOC_TEGRA30_AHUB + tristate "Tegra30 AHUB module" + help + Say Y or M if you want to add support for the Tegra30 AHUB module. + You will also need to select the individual machine drivers to + support below. + +config SND_SOC_TEGRA30_I2S + tristate "Tegra30 I2S interface" + select SND_SOC_TEGRA30_AHUB + help + Say Y or M if you want to add support for codecs attached to the + Tegra30 I2S interface. You will also need to select the individual + machine drivers to support below. + +config SND_SOC_TEGRA210_AHUB + tristate "Tegra210 AHUB module" + help + Config to enable Audio Hub (AHUB) module, which comprises of a + switch called Audio Crossbar (AXBAR) used to configure or modify + the audio routing path between various HW accelerators present in + AHUB. + Say Y or M if you want to add support for Tegra210 AHUB module. + +config SND_SOC_TEGRA210_DMIC + tristate "Tegra210 DMIC module" + help + Config to enable the Digital MIC (DMIC) controller which is used + to interface with Pulse Density Modulation (PDM) input devices. + The DMIC controller implements a converter to convert PDM signals + to Pulse Code Modulation (PCM) signals. This can be viewed as a + PDM receiver. + Say Y or M if you want to add support for Tegra210 DMIC module. + +config SND_SOC_TEGRA210_I2S + tristate "Tegra210 I2S module" + help + Config to enable the Inter-IC Sound (I2S) Controller which + implements full-duplex and bidirectional and single direction + point-to-point serial interfaces. It can interface with I2S + compatible devices. + Say Y or M if you want to add support for Tegra210 I2S module. + +config SND_SOC_TEGRA210_OPE + tristate "Tegra210 OPE module" + help + Config to enable the Output Processing Engine (OPE) which includes + Parametric Equalizer (PEQ) and Multi Band Dynamic Range Compressor + (MBDRC) sub blocks for data processing. It can support up to 8 + channels. + Say Y or M if you want to add support for Tegra210 OPE module. + +config SND_SOC_TEGRA186_ASRC + tristate "Tegra186 ASRC module" + help + Config to enable the Asynchronous Sample Rate Converter (ASRC), + which converts the sampling frequency of the input signal from + one frequency to another. It can handle over a wide range of + sample rate ratios (freq_in/freq_out) from 1:24 to 24:1. + ASRC has two modes of operation. One where ratio can be programmed + in SW and the other where it gets information from ratio estimator + module. + Say Y or M if you want to add support for Tegra186 ASRC module. + +config SND_SOC_TEGRA186_DSPK + tristate "Tegra186 DSPK module" + help + Config to enable the Digital Speaker Controller (DSPK) which + converts the multi-bit Pulse Code Modulation (PCM) audio input to + oversampled 1-bit Pulse Density Modulation (PDM) output. From the + signal flow perspective DSPK can be viewed as a PDM transmitter + that up-samples the input to the desired sampling rate by + interpolation and then converts the oversampled PCM input to + the desired 1-bit output via Delta Sigma Modulation (DSM). + Say Y or M if you want to add support for Tegra186 DSPK module. + +config SND_SOC_TEGRA210_ADMAIF + tristate "Tegra210 ADMAIF module" + help + Config to enable ADMAIF which is the interface between ADMA and + Audio Hub (AHUB). Each ADMA channel that sends/receives data to/ + from AHUB must interface through an ADMAIF channel. ADMA channel + sending data to AHUB pairs with an ADMAIF Tx channel, where as + ADMA channel receiving data from AHUB pairs with an ADMAIF Rx + channel. Buffer size is configurable for each ADMAIIF channel. + Say Y or M if you want to add support for Tegra210 ADMAIF module. + +config SND_SOC_TEGRA210_MVC + tristate "Tegra210 MVC module" + help + Config to enable the digital Master Volume Controller (MVC) which + provides gain or attenuation to a digital signal path. It can be + used in input or output signal path. It can be used either for + per-stream volume control or for master volume control. + Say Y or M if you want to add support for Tegra210 MVC module. + +config SND_SOC_TEGRA210_SFC + tristate "Tegra210 SFC module" + help + Config to enable the Sampling Frequency Converter (SFC) which + converts the sampling frequency of input signal to another + frequency. It supports sampling frequency conversion of streams + up to 2 channels (stereo). + Say Y or M if you want to add support for Tegra210 SFC module. + +config SND_SOC_TEGRA210_AMX + tristate "Tegra210 AMX module" + help + Config to enable the Audio Multiplexer (AMX) which can multiplex + four input streams (each of up to 16 channels) and generate + output stream (of up to 16 channels). A byte RAM helps to form an + output frame by any combination of bytes from the input frames. + Say Y or M if you want to add support for Tegra210 AMX module. + +config SND_SOC_TEGRA210_ADX + tristate "Tegra210 ADX module" + help + Config to enable the Audio Demultiplexer (ADX) which takes an + input stream (up to 16 channels) and demultiplexes it into four + output streams (each of up to 16 channels). A byte RAM helps to + form output frames by any combination of bytes from the input + frame. Its design is identical to that of byte RAM in the AMX + except that the data flow direction is reversed. + Say Y or M if you want to add support for Tegra210 ADX module. + +config SND_SOC_TEGRA210_MIXER + tristate "Tegra210 Mixer module" + help + Config to enable the Mixer module which can help to mix multiple + audio streams. It supports mixing of up to 10 input streams, + where each stream can contain maximum of 8 channels. It supports + 5 output each of which can be a mix of any combination of 10 + input streams. + Say Y or M if you want to add support for Tegra210 Mixer module. + +config SND_SOC_TEGRA_AUDIO_GRAPH_CARD + tristate "Audio Graph Card based Tegra driver" + depends on SND_AUDIO_GRAPH_CARD + help + Config to enable Tegra audio machine driver based on generic + audio graph driver. It is a thin driver written to customize + few things for Tegra audio. Most of the code is re-used from + audio graph driver and the same DT bindings are used. + +config SND_SOC_TEGRA_MACHINE_DRV + tristate + +config SND_SOC_TEGRA_RT5631 + tristate "SoC Audio support for Tegra boards using an RT5631 codec" + depends on SND_SOC_TEGRA && I2C && GPIOLIB + select SND_SOC_TEGRA_MACHINE_DRV + select SND_SOC_RT5631 + help + Say Y or M here if you want to add support for SoC audio on Tegra + boards using the RT5631 codec, such as Transformer. + +config SND_SOC_TEGRA_RT5640 + tristate "SoC Audio support for Tegra boards using an RT5640 codec" + depends on I2C && GPIOLIB + select SND_SOC_TEGRA_MACHINE_DRV + select SND_SOC_RT5640 + help + Say Y or M here if you want to add support for SoC audio on Tegra + boards using the RT5640 codec, such as Dalmore. + +config SND_SOC_TEGRA_WM8753 + tristate "SoC Audio support for Tegra boards using a WM8753 codec" + depends on I2C && GPIOLIB + select SND_SOC_TEGRA_MACHINE_DRV + select SND_SOC_WM8753 + help + Say Y or M here if you want to add support for SoC audio on Tegra + boards using the WM8753 codec, such as Whistler. + +config SND_SOC_TEGRA_WM8903 + tristate "SoC Audio support for Tegra boards using a WM8903 codec" + depends on I2C && GPIOLIB + select SND_SOC_TEGRA_MACHINE_DRV + select SND_SOC_WM8903 + help + Say Y or M here if you want to add support for SoC audio on Tegra + boards using the WM8093 codec. Currently, the supported boards are + Harmony, Ventana, Seaboard, Kaen, and Aebl. + +config SND_SOC_TEGRA_WM9712 + tristate "SoC Audio support for Tegra boards using a WM9712 codec" + depends on GPIOLIB + select SND_SOC_TEGRA_MACHINE_DRV + select SND_SOC_TEGRA20_AC97 + select SND_SOC_WM9712 + help + Say Y or M here if you want to add support for SoC audio on Tegra + boards using the WM9712 (or compatible) codec. + +config SND_SOC_TEGRA_TRIMSLICE + tristate "SoC Audio support for TrimSlice board" + depends on I2C + select SND_SOC_TEGRA_MACHINE_DRV + select SND_SOC_TLV320AIC23_I2C + help + Say Y or M here if you want to add support for SoC audio on the + TrimSlice platform. + +config SND_SOC_TEGRA_ALC5632 + tristate "SoC Audio support for Tegra boards using an ALC5632 codec" + depends on I2C && GPIOLIB + select SND_SOC_TEGRA_MACHINE_DRV + select SND_SOC_ALC5632 + help + Say Y or M here if you want to add support for SoC audio on the + Toshiba AC100 netbook. + +config SND_SOC_TEGRA_MAX98090 + tristate "SoC Audio support for Tegra boards using a MAX98090 codec" + depends on I2C && GPIOLIB + select SND_SOC_TEGRA_MACHINE_DRV + select SND_SOC_MAX98090 + help + Say Y or M here if you want to add support for SoC audio on Tegra + boards using the MAX98090 codec, such as Venice2. + +config SND_SOC_TEGRA_MAX98088 + tristate "SoC Audio support for Tegra boards using a MAX9808x codec" + depends on I2C && GPIOLIB + select SND_SOC_TEGRA_MACHINE_DRV + select SND_SOC_MAX98088 + help + Say Y or M here if you want to add support for SoC audio on Tegra + boards using the MAX98088 codec, such as LG X3. + +config SND_SOC_TEGRA_RT5677 + tristate "SoC Audio support for Tegra boards using a RT5677 codec" + depends on I2C && GPIOLIB + select SND_SOC_TEGRA_MACHINE_DRV + select SND_SOC_RT5677 + help + Say Y or M here if you want to add support for SoC audio on Tegra + boards using the RT5677 codec, such as Ryu. + +config SND_SOC_TEGRA_SGTL5000 + tristate "SoC Audio support for Tegra boards using a SGTL5000 codec" + depends on I2C && GPIOLIB + select SND_SOC_TEGRA_MACHINE_DRV + select SND_SOC_SGTL5000 + help + Say Y or M here if you want to add support for SoC audio on Tegra + boards using the SGTL5000 codec, such as Apalis T30, Apalis TK1 or + Colibri T30. + +endif |