From ace9429bb58fd418f0c81d4c2835699bddf6bde6 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Thu, 11 Apr 2024 10:27:49 +0200 Subject: Adding upstream version 6.6.15. Signed-off-by: Daniel Baumann --- .../devicetree/bindings/sound/cs42l56.txt | 63 ++++++++++++++++++++++ 1 file changed, 63 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/cs42l56.txt (limited to 'Documentation/devicetree/bindings/sound/cs42l56.txt') diff --git a/Documentation/devicetree/bindings/sound/cs42l56.txt b/Documentation/devicetree/bindings/sound/cs42l56.txt new file mode 100644 index 0000000000..4ba520a28a --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs42l56.txt @@ -0,0 +1,63 @@ +CS42L52 audio CODEC + +Required properties: + + - compatible : "cirrus,cs42l56" + + - reg : the I2C address of the device for I2C + + - VA-supply, VCP-supply, VLDO-supply : power supplies for the device, + as covered in Documentation/devicetree/bindings/regulator/regulator.txt. + +Optional properties: + + - cirrus,gpio-nreset : GPIO controller's phandle and the number + of the GPIO used to reset the codec. + + - cirrus,chgfreq-divisor : Values used to set the Charge Pump Frequency. + Allowable values of 0x00 through 0x0F. These are raw values written to the + register, not the actual frequency. The frequency is determined by the following. + Frequency = MCLK / 4 * (N+2) + N = chgfreq_val + MCLK = Where MCLK is the frequency of the mclk signal after the MCLKDIV2 circuit. + + - cirrus,ain1a-ref-cfg, ain1b-ref-cfg : boolean, If present, AIN1A or AIN1B are configured + as a pseudo-differential input referenced to AIN1REF/AIN3A. + + - cirrus,ain2a-ref-cfg, ain2b-ref-cfg : boolean, If present, AIN2A or AIN2B are configured + as a pseudo-differential input referenced to AIN2REF/AIN3B. + + - cirrus,micbias-lvl: Set the output voltage level on the MICBIAS Pin. + 0 = 0.5 x VA + 1 = 0.6 x VA + 2 = 0.7 x VA + 3 = 0.8 x VA + 4 = 0.83 x VA + 5 = 0.91 x VA + + - cirrus,adaptive-pwr-cfg : Configures how the power to the Headphone and Lineout + Amplifiers adapt to the output signal levels. + 0 = Adapt to Volume Mode. Voltage level determined by the sum of the relevant volume settings. + 1 = Fixed - Headphone and Line Amp supply = + or - VCP/2. + 2 = Fixed - Headphone and Line Amp supply = + or - VCP. + 3 = Adapted to Signal; Voltage level is dynamically determined by the output signal. + + - cirrus,hpf-left-freq, hpf-right-freq : Sets the corner frequency (-3dB point) for the internal High-Pass + Filter. + 0 = 1.8Hz + 1 = 119Hz + 2 = 236Hz + 3 = 464Hz + + +Example: + +codec: codec@4b { + compatible = "cirrus,cs42l56"; + reg = <0x4b>; + cirrus,gpio-nreset = <&gpio 10 0>; + cirrus,chgfreq-divisor = <0x05>; + cirrus.ain1_ref_cfg; + cirrus,micbias-lvl = <5>; + VA-supply = <®_audio>; +}; -- cgit v1.2.3