From ace9429bb58fd418f0c81d4c2835699bddf6bde6 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Thu, 11 Apr 2024 10:27:49 +0200 Subject: Adding upstream version 6.6.15. Signed-off-by: Daniel Baumann --- arch/arm/boot/dts/marvell/armada-xp-gp.dts | 230 +++++++++++++++++++++++++++++ 1 file changed, 230 insertions(+) create mode 100644 arch/arm/boot/dts/marvell/armada-xp-gp.dts (limited to 'arch/arm/boot/dts/marvell/armada-xp-gp.dts') diff --git a/arch/arm/boot/dts/marvell/armada-xp-gp.dts b/arch/arm/boot/dts/marvell/armada-xp-gp.dts new file mode 100644 index 0000000000..d1d348b91c --- /dev/null +++ b/arch/arm/boot/dts/marvell/armada-xp-gp.dts @@ -0,0 +1,230 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Device Tree file for Marvell Armada XP development board + * (DB-MV784MP-GP) + * + * Copyright (C) 2013-2014 Marvell + * + * Lior Amsalem + * Gregory CLEMENT + * Thomas Petazzoni + * + * Note: this Device Tree assumes that the bootloader has remapped the + * internal registers to 0xf1000000 (instead of the default + * 0xd0000000). The 0xf1000000 is the default used by the recent, + * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier + * boards were delivered with an older version of the bootloader that + * left internal registers mapped at 0xd0000000. If you are in this + * situation, you should either update your bootloader (preferred + * solution) or the below Device Tree should be adjusted. + */ + +/dts-v1/; +#include +#include "armada-xp-mv78460.dtsi" + +/ { + model = "Marvell Armada XP Development Board DB-MV784MP-GP"; + compatible = "marvell,axp-gp", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + /* + * 8 GB of plug-in RAM modules by default.The amount + * of memory available can be changed by the + * bootloader according the size of the module + * actually plugged. However, memory between + * 0xF0000000 to 0xFFFFFFFF cannot be used, as it is + * the address range used for I/O (internal registers, + * MBus windows). + */ + reg = <0x00000000 0x00000000 0x00000000 0xf0000000>, + <0x00000001 0x00000000 0x00000001 0x00000000>; + }; + + cpus { + pm_pic { + ctrl-gpios = <&gpio0 16 GPIO_ACTIVE_LOW>, + <&gpio0 17 GPIO_ACTIVE_LOW>, + <&gpio0 18 GPIO_ACTIVE_LOW>; + }; + }; + + soc { + ranges = ; + + devbus-bootcs { + status = "okay"; + + /* Device Bus parameters are required */ + + /* Read parameters */ + devbus,bus-width = <16>; + devbus,turn-off-ps = <60000>; + devbus,badr-skew-ps = <0>; + devbus,acc-first-ps = <124000>; + devbus,acc-next-ps = <248000>; + devbus,rd-setup-ps = <0>; + devbus,rd-hold-ps = <0>; + + /* Write parameters */ + devbus,sync-enable = <0>; + devbus,wr-high-ps = <60000>; + devbus,wr-low-ps = <60000>; + devbus,ale-wr-ps = <60000>; + + /* NOR 16 MiB */ + nor@0 { + compatible = "cfi-flash"; + reg = <0 0x1000000>; + bank-width = <2>; + }; + }; + + internal-regs { + serial@12000 { + status = "okay"; + }; + serial@12100 { + status = "okay"; + }; + serial@12200 { + status = "okay"; + }; + serial@12300 { + status = "okay"; + }; + pinctrl { + pinctrl-0 = <&pic_pins>; + pinctrl-names = "default"; + pic_pins: pic-pins-0 { + marvell,pins = "mpp16", "mpp17", + "mpp18"; + marvell,function = "gpio"; + }; + }; + sata@a0000 { + nr-ports = <2>; + status = "okay"; + }; + + ethernet@70000 { + status = "okay"; + phy = <&phy0>; + phy-mode = "qsgmii"; + buffer-manager = <&bm>; + bm,pool-long = <0>; + }; + ethernet@74000 { + status = "okay"; + phy = <&phy1>; + phy-mode = "qsgmii"; + buffer-manager = <&bm>; + bm,pool-long = <1>; + }; + ethernet@30000 { + status = "okay"; + phy = <&phy2>; + phy-mode = "qsgmii"; + buffer-manager = <&bm>; + bm,pool-long = <2>; + }; + ethernet@34000 { + status = "okay"; + phy = <&phy3>; + phy-mode = "qsgmii"; + buffer-manager = <&bm>; + bm,pool-long = <3>; + }; + + /* Front-side USB slot */ + usb@50000 { + status = "okay"; + }; + + /* Back-side USB slot */ + usb@51000 { + status = "okay"; + }; + + bm@c0000 { + status = "okay"; + }; + + nand-controller@d0000 { + status = "okay"; + + nand@0 { + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + nand-on-flash-bbt; + }; + }; + }; + + bm-bppi { + status = "okay"; + }; + }; +}; + +&pciec { + status = "okay"; + + /* + * The 3 slots are physically present as + * standard PCIe slots on the board. + */ + pcie@1,0 { + /* Port 0, Lane 0 */ + status = "okay"; + }; + pcie@9,0 { + /* Port 2, Lane 0 */ + status = "okay"; + }; + pcie@a,0 { + /* Port 3, Lane 0 */ + status = "okay"; + }; +}; + +&mdio { + phy0: ethernet-phy@0 { + reg = <16>; + }; + + phy1: ethernet-phy@1 { + reg = <17>; + }; + + phy2: ethernet-phy@2 { + reg = <18>; + }; + + phy3: ethernet-phy@3 { + reg = <19>; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "n25q128a13", "jedec,spi-nor"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <108000000>; + }; +}; -- cgit v1.2.3