From ace9429bb58fd418f0c81d4c2835699bddf6bde6 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Thu, 11 Apr 2024 10:27:49 +0200 Subject: Adding upstream version 6.6.15. Signed-off-by: Daniel Baumann --- drivers/net/wireless/ath/ath10k/hw.h | 1206 ++++++++++++++++++++++++++++++++++ 1 file changed, 1206 insertions(+) create mode 100644 drivers/net/wireless/ath/ath10k/hw.h (limited to 'drivers/net/wireless/ath/ath10k/hw.h') diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h new file mode 100644 index 0000000000..9643031a44 --- /dev/null +++ b/drivers/net/wireless/ath/ath10k/hw.h @@ -0,0 +1,1206 @@ +/* SPDX-License-Identifier: ISC */ +/* + * Copyright (c) 2005-2011 Atheros Communications Inc. + * Copyright (c) 2011-2017 Qualcomm Atheros, Inc. + * Copyright (c) 2018 The Linux Foundation. All rights reserved. + */ + +#ifndef _HW_H_ +#define _HW_H_ + +#include "targaddrs.h" + +enum ath10k_bus { + ATH10K_BUS_PCI, + ATH10K_BUS_AHB, + ATH10K_BUS_SDIO, + ATH10K_BUS_USB, + ATH10K_BUS_SNOC, +}; + +#define ATH10K_FW_DIR "ath10k" + +#define QCA988X_2_0_DEVICE_ID_UBNT (0x11ac) +#define QCA988X_2_0_DEVICE_ID (0x003c) +#define QCA6164_2_1_DEVICE_ID (0x0041) +#define QCA6174_2_1_DEVICE_ID (0x003e) +#define QCA6174_3_2_DEVICE_ID (0x0042) +#define QCA99X0_2_0_DEVICE_ID (0x0040) +#define QCA9888_2_0_DEVICE_ID (0x0056) +#define QCA9984_1_0_DEVICE_ID (0x0046) +#define QCA9377_1_0_DEVICE_ID (0x0042) +#define QCA9887_1_0_DEVICE_ID (0x0050) + +/* QCA988X 1.0 definitions (unsupported) */ +#define QCA988X_HW_1_0_CHIP_ID_REV 0x0 + +/* QCA988X 2.0 definitions */ +#define QCA988X_HW_2_0_VERSION 0x4100016c +#define QCA988X_HW_2_0_CHIP_ID_REV 0x2 +#define QCA988X_HW_2_0_FW_DIR ATH10K_FW_DIR "/QCA988X/hw2.0" +#define QCA988X_HW_2_0_BOARD_DATA_FILE "board.bin" +#define QCA988X_HW_2_0_PATCH_LOAD_ADDR 0x1234 + +/* QCA9887 1.0 definitions */ +#define QCA9887_HW_1_0_VERSION 0x4100016d +#define QCA9887_HW_1_0_CHIP_ID_REV 0 +#define QCA9887_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA9887/hw1.0" +#define QCA9887_HW_1_0_BOARD_DATA_FILE "board.bin" +#define QCA9887_HW_1_0_PATCH_LOAD_ADDR 0x1234 + +/* QCA6174 target BMI version signatures */ +#define QCA6174_HW_1_0_VERSION 0x05000000 +#define QCA6174_HW_1_1_VERSION 0x05000001 +#define QCA6174_HW_1_3_VERSION 0x05000003 +#define QCA6174_HW_2_1_VERSION 0x05010000 +#define QCA6174_HW_3_0_VERSION 0x05020000 +#define QCA6174_HW_3_2_VERSION 0x05030000 + +/* QCA9377 target BMI version signatures */ +#define QCA9377_HW_1_0_DEV_VERSION 0x05020000 +#define QCA9377_HW_1_1_DEV_VERSION 0x05020001 + +enum qca6174_pci_rev { + QCA6174_PCI_REV_1_1 = 0x11, + QCA6174_PCI_REV_1_3 = 0x13, + QCA6174_PCI_REV_2_0 = 0x20, + QCA6174_PCI_REV_3_0 = 0x30, +}; + +enum qca6174_chip_id_rev { + QCA6174_HW_1_0_CHIP_ID_REV = 0, + QCA6174_HW_1_1_CHIP_ID_REV = 1, + QCA6174_HW_1_3_CHIP_ID_REV = 2, + QCA6174_HW_2_1_CHIP_ID_REV = 4, + QCA6174_HW_2_2_CHIP_ID_REV = 5, + QCA6174_HW_3_0_CHIP_ID_REV = 8, + QCA6174_HW_3_1_CHIP_ID_REV = 9, + QCA6174_HW_3_2_CHIP_ID_REV = 10, +}; + +enum qca9377_chip_id_rev { + QCA9377_HW_1_0_CHIP_ID_REV = 0x0, + QCA9377_HW_1_1_CHIP_ID_REV = 0x1, +}; + +#define QCA6174_HW_2_1_FW_DIR ATH10K_FW_DIR "/QCA6174/hw2.1" +#define QCA6174_HW_2_1_BOARD_DATA_FILE "board.bin" +#define QCA6174_HW_2_1_PATCH_LOAD_ADDR 0x1234 + +#define QCA6174_HW_3_0_FW_DIR ATH10K_FW_DIR "/QCA6174/hw3.0" +#define QCA6174_HW_3_0_BOARD_DATA_FILE "board.bin" +#define QCA6174_HW_3_0_PATCH_LOAD_ADDR 0x1234 + +/* QCA99X0 1.0 definitions (unsupported) */ +#define QCA99X0_HW_1_0_CHIP_ID_REV 0x0 + +/* QCA99X0 2.0 definitions */ +#define QCA99X0_HW_2_0_DEV_VERSION 0x01000000 +#define QCA99X0_HW_2_0_CHIP_ID_REV 0x1 +#define QCA99X0_HW_2_0_FW_DIR ATH10K_FW_DIR "/QCA99X0/hw2.0" +#define QCA99X0_HW_2_0_BOARD_DATA_FILE "board.bin" +#define QCA99X0_HW_2_0_PATCH_LOAD_ADDR 0x1234 + +/* QCA9984 1.0 defines */ +#define QCA9984_HW_1_0_DEV_VERSION 0x1000000 +#define QCA9984_HW_DEV_TYPE 0xa +#define QCA9984_HW_1_0_CHIP_ID_REV 0x0 +#define QCA9984_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA9984/hw1.0" +#define QCA9984_HW_1_0_BOARD_DATA_FILE "board.bin" +#define QCA9984_HW_1_0_EBOARD_DATA_FILE "eboard.bin" +#define QCA9984_HW_1_0_PATCH_LOAD_ADDR 0x1234 + +/* QCA9888 2.0 defines */ +#define QCA9888_HW_2_0_DEV_VERSION 0x1000000 +#define QCA9888_HW_DEV_TYPE 0xc +#define QCA9888_HW_2_0_CHIP_ID_REV 0x0 +#define QCA9888_HW_2_0_FW_DIR ATH10K_FW_DIR "/QCA9888/hw2.0" +#define QCA9888_HW_2_0_BOARD_DATA_FILE "board.bin" +#define QCA9888_HW_2_0_PATCH_LOAD_ADDR 0x1234 + +/* QCA9377 1.0 definitions */ +#define QCA9377_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA9377/hw1.0" +#define QCA9377_HW_1_0_BOARD_DATA_FILE "board.bin" +#define QCA9377_HW_1_0_PATCH_LOAD_ADDR 0x1234 + +/* QCA4019 1.0 definitions */ +#define QCA4019_HW_1_0_DEV_VERSION 0x01000000 +#define QCA4019_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA4019/hw1.0" +#define QCA4019_HW_1_0_BOARD_DATA_FILE "board.bin" +#define QCA4019_HW_1_0_PATCH_LOAD_ADDR 0x1234 + +/* WCN3990 1.0 definitions */ +#define WCN3990_HW_1_0_DEV_VERSION ATH10K_HW_WCN3990 +#define WCN3990_HW_1_0_FW_DIR ATH10K_FW_DIR "/WCN3990/hw1.0" + +#define ATH10K_FW_FILE_BASE "firmware" +#define ATH10K_FW_API_MAX 6 +#define ATH10K_FW_API_MIN 2 + +#define ATH10K_FW_API2_FILE "firmware-2.bin" +#define ATH10K_FW_API3_FILE "firmware-3.bin" + +/* added support for ATH10K_FW_IE_WMI_OP_VERSION */ +#define ATH10K_FW_API4_FILE "firmware-4.bin" + +/* HTT id conflict fix for management frames over HTT */ +#define ATH10K_FW_API5_FILE "firmware-5.bin" + +/* the firmware-6.bin blob */ +#define ATH10K_FW_API6_FILE "firmware-6.bin" + +#define ATH10K_FW_UTF_FILE "utf.bin" +#define ATH10K_FW_UTF_API2_FILE "utf-2.bin" + +#define ATH10K_FW_UTF_FILE_BASE "utf" + +/* includes also the null byte */ +#define ATH10K_FIRMWARE_MAGIC "QCA-ATH10K" +#define ATH10K_BOARD_MAGIC "QCA-ATH10K-BOARD" + +#define ATH10K_BOARD_API2_FILE "board-2.bin" + +#define REG_DUMP_COUNT_QCA988X 60 + +struct ath10k_fw_ie { + __le32 id; + __le32 len; + u8 data[]; +}; + +enum ath10k_fw_ie_type { + ATH10K_FW_IE_FW_VERSION = 0, + ATH10K_FW_IE_TIMESTAMP = 1, + ATH10K_FW_IE_FEATURES = 2, + ATH10K_FW_IE_FW_IMAGE = 3, + ATH10K_FW_IE_OTP_IMAGE = 4, + + /* WMI "operations" interface version, 32 bit value. Supported from + * FW API 4 and above. + */ + ATH10K_FW_IE_WMI_OP_VERSION = 5, + + /* HTT "operations" interface version, 32 bit value. Supported from + * FW API 5 and above. + */ + ATH10K_FW_IE_HTT_OP_VERSION = 6, + + /* Code swap image for firmware binary */ + ATH10K_FW_IE_FW_CODE_SWAP_IMAGE = 7, +}; + +enum ath10k_fw_wmi_op_version { + ATH10K_FW_WMI_OP_VERSION_UNSET = 0, + + ATH10K_FW_WMI_OP_VERSION_MAIN = 1, + ATH10K_FW_WMI_OP_VERSION_10_1 = 2, + ATH10K_FW_WMI_OP_VERSION_10_2 = 3, + ATH10K_FW_WMI_OP_VERSION_TLV = 4, + ATH10K_FW_WMI_OP_VERSION_10_2_4 = 5, + ATH10K_FW_WMI_OP_VERSION_10_4 = 6, + + /* keep last */ + ATH10K_FW_WMI_OP_VERSION_MAX, +}; + +enum ath10k_fw_htt_op_version { + ATH10K_FW_HTT_OP_VERSION_UNSET = 0, + + ATH10K_FW_HTT_OP_VERSION_MAIN = 1, + + /* also used in 10.2 and 10.2.4 branches */ + ATH10K_FW_HTT_OP_VERSION_10_1 = 2, + + ATH10K_FW_HTT_OP_VERSION_TLV = 3, + + ATH10K_FW_HTT_OP_VERSION_10_4 = 4, + + /* keep last */ + ATH10K_FW_HTT_OP_VERSION_MAX, +}; + +enum ath10k_bd_ie_type { + /* contains sub IEs of enum ath10k_bd_ie_board_type */ + ATH10K_BD_IE_BOARD = 0, + ATH10K_BD_IE_BOARD_EXT = 1, +}; + +enum ath10k_bd_ie_board_type { + ATH10K_BD_IE_BOARD_NAME = 0, + ATH10K_BD_IE_BOARD_DATA = 1, +}; + +enum ath10k_hw_rev { + ATH10K_HW_QCA988X, + ATH10K_HW_QCA6174, + ATH10K_HW_QCA99X0, + ATH10K_HW_QCA9888, + ATH10K_HW_QCA9984, + ATH10K_HW_QCA9377, + ATH10K_HW_QCA4019, + ATH10K_HW_QCA9887, + ATH10K_HW_WCN3990, +}; + +struct ath10k_hw_regs { + u32 rtc_soc_base_address; + u32 rtc_wmac_base_address; + u32 soc_core_base_address; + u32 wlan_mac_base_address; + u32 ce_wrapper_base_address; + u32 ce0_base_address; + u32 ce1_base_address; + u32 ce2_base_address; + u32 ce3_base_address; + u32 ce4_base_address; + u32 ce5_base_address; + u32 ce6_base_address; + u32 ce7_base_address; + u32 ce8_base_address; + u32 ce9_base_address; + u32 ce10_base_address; + u32 ce11_base_address; + u32 soc_reset_control_si0_rst_mask; + u32 soc_reset_control_ce_rst_mask; + u32 soc_chip_id_address; + u32 scratch_3_address; + u32 fw_indicator_address; + u32 pcie_local_base_address; + u32 ce_wrap_intr_sum_host_msi_lsb; + u32 ce_wrap_intr_sum_host_msi_mask; + u32 pcie_intr_fw_mask; + u32 pcie_intr_ce_mask_all; + u32 pcie_intr_clr_address; + u32 cpu_pll_init_address; + u32 cpu_speed_address; + u32 core_clk_div_address; +}; + +extern const struct ath10k_hw_regs qca988x_regs; +extern const struct ath10k_hw_regs qca6174_regs; +extern const struct ath10k_hw_regs qca99x0_regs; +extern const struct ath10k_hw_regs qca4019_regs; +extern const struct ath10k_hw_regs wcn3990_regs; + +struct ath10k_hw_ce_regs_addr_map { + u32 msb; + u32 lsb; + u32 mask; +}; + +struct ath10k_hw_ce_ctrl1 { + u32 addr; + u32 hw_mask; + u32 sw_mask; + u32 hw_wr_mask; + u32 sw_wr_mask; + u32 reset_mask; + u32 reset; + struct ath10k_hw_ce_regs_addr_map *src_ring; + struct ath10k_hw_ce_regs_addr_map *dst_ring; + struct ath10k_hw_ce_regs_addr_map *dmax; }; + +struct ath10k_hw_ce_cmd_halt { + u32 status_reset; + u32 msb; + u32 mask; + struct ath10k_hw_ce_regs_addr_map *status; }; + +struct ath10k_hw_ce_host_ie { + u32 copy_complete_reset; + struct ath10k_hw_ce_regs_addr_map *copy_complete; }; + +struct ath10k_hw_ce_host_wm_regs { + u32 dstr_lmask; + u32 dstr_hmask; + u32 srcr_lmask; + u32 srcr_hmask; + u32 cc_mask; + u32 wm_mask; + u32 addr; +}; + +struct ath10k_hw_ce_misc_regs { + u32 axi_err; + u32 dstr_add_err; + u32 srcr_len_err; + u32 dstr_mlen_vio; + u32 dstr_overflow; + u32 srcr_overflow; + u32 err_mask; + u32 addr; +}; + +struct ath10k_hw_ce_dst_src_wm_regs { + u32 addr; + u32 low_rst; + u32 high_rst; + struct ath10k_hw_ce_regs_addr_map *wm_low; + struct ath10k_hw_ce_regs_addr_map *wm_high; }; + +struct ath10k_hw_ce_ctrl1_upd { + u32 shift; + u32 mask; + u32 enable; +}; + +struct ath10k_hw_ce_regs { + u32 sr_base_addr_lo; + u32 sr_base_addr_hi; + u32 sr_size_addr; + u32 dr_base_addr_lo; + u32 dr_base_addr_hi; + u32 dr_size_addr; + u32 ce_cmd_addr; + u32 misc_ie_addr; + u32 sr_wr_index_addr; + u32 dst_wr_index_addr; + u32 current_srri_addr; + u32 current_drri_addr; + u32 ddr_addr_for_rri_low; + u32 ddr_addr_for_rri_high; + u32 ce_rri_low; + u32 ce_rri_high; + u32 host_ie_addr; + struct ath10k_hw_ce_host_wm_regs *wm_regs; + struct ath10k_hw_ce_misc_regs *misc_regs; + struct ath10k_hw_ce_ctrl1 *ctrl1_regs; + struct ath10k_hw_ce_cmd_halt *cmd_halt; + struct ath10k_hw_ce_host_ie *host_ie; + struct ath10k_hw_ce_dst_src_wm_regs *wm_srcr; + struct ath10k_hw_ce_dst_src_wm_regs *wm_dstr; + struct ath10k_hw_ce_ctrl1_upd *upd; +}; + +struct ath10k_hw_values { + u32 rtc_state_val_on; + u8 ce_count; + u8 msi_assign_ce_max; + u8 num_target_ce_config_wlan; + u16 ce_desc_meta_data_mask; + u8 ce_desc_meta_data_lsb; + u32 rfkill_pin; + u32 rfkill_cfg; + bool rfkill_on_level; +}; + +extern const struct ath10k_hw_values qca988x_values; +extern const struct ath10k_hw_values qca6174_values; +extern const struct ath10k_hw_values qca99x0_values; +extern const struct ath10k_hw_values qca9888_values; +extern const struct ath10k_hw_values qca4019_values; +extern const struct ath10k_hw_values wcn3990_values; +extern const struct ath10k_hw_ce_regs wcn3990_ce_regs; +extern const struct ath10k_hw_ce_regs qcax_ce_regs; + +void ath10k_hw_fill_survey_time(struct ath10k *ar, struct survey_info *survey, + u32 cc, u32 rcc, u32 cc_prev, u32 rcc_prev); + +int ath10k_hw_diag_fast_download(struct ath10k *ar, + u32 address, + const void *buffer, + u32 length); + +#define QCA_REV_988X(ar) ((ar)->hw_rev == ATH10K_HW_QCA988X) +#define QCA_REV_9887(ar) ((ar)->hw_rev == ATH10K_HW_QCA9887) +#define QCA_REV_6174(ar) ((ar)->hw_rev == ATH10K_HW_QCA6174) +#define QCA_REV_99X0(ar) ((ar)->hw_rev == ATH10K_HW_QCA99X0) +#define QCA_REV_9888(ar) ((ar)->hw_rev == ATH10K_HW_QCA9888) +#define QCA_REV_9984(ar) ((ar)->hw_rev == ATH10K_HW_QCA9984) +#define QCA_REV_9377(ar) ((ar)->hw_rev == ATH10K_HW_QCA9377) +#define QCA_REV_40XX(ar) ((ar)->hw_rev == ATH10K_HW_QCA4019) +#define QCA_REV_WCN3990(ar) ((ar)->hw_rev == ATH10K_HW_WCN3990) + +/* Known peculiarities: + * - raw appears in nwifi decap, raw and nwifi appear in ethernet decap + * - raw have FCS, nwifi doesn't + * - ethernet frames have 802.11 header decapped and parts (base hdr, cipher + * param, llc/snap) are aligned to 4byte boundaries each + */ +enum ath10k_hw_txrx_mode { + ATH10K_HW_TXRX_RAW = 0, + + /* Native Wifi decap mode is used to align IP frames to 4-byte + * boundaries and avoid a very expensive re-alignment in mac80211. + */ + ATH10K_HW_TXRX_NATIVE_WIFI = 1, + ATH10K_HW_TXRX_ETHERNET = 2, + + /* Valid for HTT >= 3.0. Used for management frames in TX_FRM. */ + ATH10K_HW_TXRX_MGMT = 3, +}; + +enum ath10k_mcast2ucast_mode { + ATH10K_MCAST2UCAST_DISABLED = 0, + ATH10K_MCAST2UCAST_ENABLED = 1, +}; + +enum ath10k_hw_rate_ofdm { + ATH10K_HW_RATE_OFDM_48M = 0, + ATH10K_HW_RATE_OFDM_24M, + ATH10K_HW_RATE_OFDM_12M, + ATH10K_HW_RATE_OFDM_6M, + ATH10K_HW_RATE_OFDM_54M, + ATH10K_HW_RATE_OFDM_36M, + ATH10K_HW_RATE_OFDM_18M, + ATH10K_HW_RATE_OFDM_9M, +}; + +enum ath10k_hw_rate_cck { + ATH10K_HW_RATE_CCK_LP_11M = 0, + ATH10K_HW_RATE_CCK_LP_5_5M, + ATH10K_HW_RATE_CCK_LP_2M, + ATH10K_HW_RATE_CCK_LP_1M, + ATH10K_HW_RATE_CCK_SP_11M, + ATH10K_HW_RATE_CCK_SP_5_5M, + ATH10K_HW_RATE_CCK_SP_2M, +}; + +enum ath10k_hw_rate_rev2_cck { + ATH10K_HW_RATE_REV2_CCK_LP_1M = 1, + ATH10K_HW_RATE_REV2_CCK_LP_2M, + ATH10K_HW_RATE_REV2_CCK_LP_5_5M, + ATH10K_HW_RATE_REV2_CCK_LP_11M, + ATH10K_HW_RATE_REV2_CCK_SP_2M, + ATH10K_HW_RATE_REV2_CCK_SP_5_5M, + ATH10K_HW_RATE_REV2_CCK_SP_11M, +}; + +enum ath10k_hw_cc_wraparound_type { + ATH10K_HW_CC_WRAP_DISABLED = 0, + + /* This type is when the HW chip has a quirky Cycle Counter + * wraparound which resets to 0x7fffffff instead of 0. All + * other CC related counters (e.g. Rx Clear Count) are divided + * by 2 so they never wraparound themselves. + */ + ATH10K_HW_CC_WRAP_SHIFTED_ALL = 1, + + /* Each hw counter wrapsaround independently. When the + * counter overflows the repestive counter is right shifted + * by 1, i.e reset to 0x7fffffff, and other counters will be + * running unaffected. In this type of wraparound, it should + * be possible to report accurate Rx busy time unlike the + * first type. + */ + ATH10K_HW_CC_WRAP_SHIFTED_EACH = 2, +}; + +enum ath10k_hw_refclk_speed { + ATH10K_HW_REFCLK_UNKNOWN = -1, + ATH10K_HW_REFCLK_48_MHZ = 0, + ATH10K_HW_REFCLK_19_2_MHZ = 1, + ATH10K_HW_REFCLK_24_MHZ = 2, + ATH10K_HW_REFCLK_26_MHZ = 3, + ATH10K_HW_REFCLK_37_4_MHZ = 4, + ATH10K_HW_REFCLK_38_4_MHZ = 5, + ATH10K_HW_REFCLK_40_MHZ = 6, + ATH10K_HW_REFCLK_52_MHZ = 7, + + /* must be the last one */ + ATH10K_HW_REFCLK_COUNT, +}; + +struct ath10k_hw_clk_params { + u32 refclk; + u32 div; + u32 rnfrac; + u32 settle_time; + u32 refdiv; + u32 outdiv; +}; + +struct htt_rx_desc_ops; + +struct ath10k_hw_params { + u32 id; + u16 dev_id; + enum ath10k_bus bus; + const char *name; + u32 patch_load_addr; + int uart_pin; + u32 otp_exe_param; + + /* Type of hw cycle counter wraparound logic, for more info + * refer enum ath10k_hw_cc_wraparound_type. + */ + enum ath10k_hw_cc_wraparound_type cc_wraparound_type; + + /* Some of chip expects fragment descriptor to be continuous + * memory for any TX operation. Set continuous_frag_desc flag + * for the hardware which have such requirement. + */ + bool continuous_frag_desc; + + /* CCK hardware rate table mapping for the newer chipsets + * like QCA99X0, QCA4019 got revised. The CCK h/w rate values + * are in a proper order with respect to the rate/preamble + */ + bool cck_rate_map_rev2; + + u32 channel_counters_freq_hz; + + /* Mgmt tx descriptors threshold for limiting probe response + * frames. + */ + u32 max_probe_resp_desc_thres; + + u32 tx_chain_mask; + u32 rx_chain_mask; + u32 max_spatial_stream; + u32 cal_data_len; + + struct ath10k_hw_params_fw { + const char *dir; + const char *board; + size_t board_size; + const char *eboard; + size_t ext_board_size; + size_t board_ext_size; + } fw; + + /* qca99x0 family chips deliver broadcast/multicast management + * frames encrypted and expect software do decryption. + */ + bool sw_decrypt_mcast_mgmt; + + /* Rx descriptor abstraction */ + const struct ath10k_htt_rx_desc_ops *rx_desc_ops; + + const struct ath10k_hw_ops *hw_ops; + + /* Number of bytes used for alignment in rx_hdr_status of rx desc. */ + int decap_align_bytes; + + /* hw specific clock control parameters */ + const struct ath10k_hw_clk_params *hw_clk; + int target_cpu_freq; + + /* Number of bytes to be discarded for each FFT sample */ + int spectral_bin_discard; + + /* The board may have a restricted NSS for 160 or 80+80 vs what it + * can do for 80Mhz. + */ + int vht160_mcs_rx_highest; + int vht160_mcs_tx_highest; + + /* Number of ciphers supported (i.e First N) in cipher_suites array */ + int n_cipher_suites; + + u32 num_peers; + u32 ast_skid_limit; + u32 num_wds_entries; + + /* Targets supporting physical addressing capability above 32-bits */ + bool target_64bit; + + /* Target rx ring fill level */ + u32 rx_ring_fill_level; + + /* target supporting shadow register for ce write */ + bool shadow_reg_support; + + /* target supporting retention restore on ddr */ + bool rri_on_ddr; + + /* Number of bytes to be the offset for each FFT sample */ + int spectral_bin_offset; + + /* targets which require hw filter reset during boot up, + * to avoid it sending spurious acks. + */ + bool hw_filter_reset_required; + + /* target supporting fw download via diag ce */ + bool fw_diag_ce_download; + + /* target supporting fw download via large size BMI */ + bool bmi_large_size_download; + + /* need to set uart pin if disable uart print, workaround for a + * firmware bug + */ + bool uart_pin_workaround; + + /* Workaround for the credit size calculation */ + bool credit_size_workaround; + + /* tx stats support over pktlog */ + bool tx_stats_over_pktlog; + + /* provides bitrates for sta_statistics using WMI_TLV_PEER_STATS_INFO_EVENTID */ + bool supports_peer_stats_info; + + bool dynamic_sar_support; + + bool hw_restart_disconnect; + + bool use_fw_tx_credits; + + bool delay_unmap_buffer; +}; + +struct htt_resp; +struct htt_data_tx_completion_ext; +struct htt_rx_ring_rx_desc_offsets; + +/* Defines needed for Rx descriptor abstraction */ +struct ath10k_hw_ops { + void (*set_coverage_class)(struct ath10k *ar, s16 value); + int (*enable_pll_clk)(struct ath10k *ar); + int (*tx_data_rssi_pad_bytes)(struct htt_resp *htt); + int (*is_rssi_enable)(struct htt_resp *resp); +}; + +extern const struct ath10k_hw_ops qca988x_ops; +extern const struct ath10k_hw_ops qca99x0_ops; +extern const struct ath10k_hw_ops qca6174_ops; +extern const struct ath10k_hw_ops qca6174_sdio_ops; +extern const struct ath10k_hw_ops wcn3990_ops; + +extern const struct ath10k_hw_clk_params qca6174_clk[]; + +static inline int +ath10k_tx_data_rssi_get_pad_bytes(struct ath10k_hw_params *hw, + struct htt_resp *htt) +{ + if (hw->hw_ops->tx_data_rssi_pad_bytes) + return hw->hw_ops->tx_data_rssi_pad_bytes(htt); + return 0; +} + +static inline int +ath10k_is_rssi_enable(struct ath10k_hw_params *hw, + struct htt_resp *resp) +{ + if (hw->hw_ops->is_rssi_enable) + return hw->hw_ops->is_rssi_enable(resp); + return 0; +} + +/* Target specific defines for MAIN firmware */ +#define TARGET_NUM_VDEVS 8 +#define TARGET_NUM_PEER_AST 2 +#define TARGET_NUM_WDS_ENTRIES 32 +#define TARGET_DMA_BURST_SIZE 0 +#define TARGET_MAC_AGGR_DELIM 0 +#define TARGET_AST_SKID_LIMIT 16 +#define TARGET_NUM_STATIONS 16 +#define TARGET_NUM_PEERS ((TARGET_NUM_STATIONS) + \ + (TARGET_NUM_VDEVS)) +#define TARGET_NUM_OFFLOAD_PEERS 0 +#define TARGET_NUM_OFFLOAD_REORDER_BUFS 0 +#define TARGET_NUM_PEER_KEYS 2 +#define TARGET_NUM_TIDS ((TARGET_NUM_PEERS) * 2) +#define TARGET_TX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2)) +#define TARGET_RX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2)) +#define TARGET_RX_TIMEOUT_LO_PRI 100 +#define TARGET_RX_TIMEOUT_HI_PRI 40 + +#define TARGET_SCAN_MAX_PENDING_REQS 4 +#define TARGET_BMISS_OFFLOAD_MAX_VDEV 3 +#define TARGET_ROAM_OFFLOAD_MAX_VDEV 3 +#define TARGET_ROAM_OFFLOAD_MAX_AP_PROFILES 8 +#define TARGET_GTK_OFFLOAD_MAX_VDEV 3 +#define TARGET_NUM_MCAST_GROUPS 0 +#define TARGET_NUM_MCAST_TABLE_ELEMS 0 +#define TARGET_MCAST2UCAST_MODE ATH10K_MCAST2UCAST_DISABLED +#define TARGET_TX_DBG_LOG_SIZE 1024 +#define TARGET_RX_SKIP_DEFRAG_TIMEOUT_DUP_DETECTION_CHECK 0 +#define TARGET_VOW_CONFIG 0 +#define TARGET_NUM_MSDU_DESC (1024 + 400) +#define TARGET_MAX_FRAG_ENTRIES 0 + +/* Target specific defines for 10.X firmware */ +#define TARGET_10X_NUM_VDEVS 16 +#define TARGET_10X_NUM_PEER_AST 2 +#define TARGET_10X_NUM_WDS_ENTRIES 32 +#define TARGET_10X_DMA_BURST_SIZE 0 +#define TARGET_10X_MAC_AGGR_DELIM 0 +#define TARGET_10X_AST_SKID_LIMIT 128 +#define TARGET_10X_NUM_STATIONS 128 +#define TARGET_10X_TX_STATS_NUM_STATIONS 118 +#define TARGET_10X_NUM_PEERS ((TARGET_10X_NUM_STATIONS) + \ + (TARGET_10X_NUM_VDEVS)) +#define TARGET_10X_TX_STATS_NUM_PEERS ((TARGET_10X_TX_STATS_NUM_STATIONS) + \ + (TARGET_10X_NUM_VDEVS)) +#define TARGET_10X_NUM_OFFLOAD_PEERS 0 +#define TARGET_10X_NUM_OFFLOAD_REORDER_BUFS 0 +#define TARGET_10X_NUM_PEER_KEYS 2 +#define TARGET_10X_NUM_TIDS_MAX 256 +#define TARGET_10X_NUM_TIDS min((TARGET_10X_NUM_TIDS_MAX), \ + (TARGET_10X_NUM_PEERS) * 2) +#define TARGET_10X_TX_STATS_NUM_TIDS min((TARGET_10X_NUM_TIDS_MAX), \ + (TARGET_10X_TX_STATS_NUM_PEERS) * 2) +#define TARGET_10X_TX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2)) +#define TARGET_10X_RX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2)) +#define TARGET_10X_RX_TIMEOUT_LO_PRI 100 +#define TARGET_10X_RX_TIMEOUT_HI_PRI 40 +#define TARGET_10X_SCAN_MAX_PENDING_REQS 4 +#define TARGET_10X_BMISS_OFFLOAD_MAX_VDEV 2 +#define TARGET_10X_ROAM_OFFLOAD_MAX_VDEV 2 +#define TARGET_10X_ROAM_OFFLOAD_MAX_AP_PROFILES 8 +#define TARGET_10X_GTK_OFFLOAD_MAX_VDEV 3 +#define TARGET_10X_NUM_MCAST_GROUPS 0 +#define TARGET_10X_NUM_MCAST_TABLE_ELEMS 0 +#define TARGET_10X_MCAST2UCAST_MODE ATH10K_MCAST2UCAST_DISABLED +#define TARGET_10X_TX_DBG_LOG_SIZE 1024 +#define TARGET_10X_RX_SKIP_DEFRAG_TIMEOUT_DUP_DETECTION_CHECK 1 +#define TARGET_10X_VOW_CONFIG 0 +#define TARGET_10X_NUM_MSDU_DESC (1024 + 400) +#define TARGET_10X_MAX_FRAG_ENTRIES 0 + +/* 10.2 parameters */ +#define TARGET_10_2_DMA_BURST_SIZE 0 + +/* Target specific defines for WMI-TLV firmware */ +#define TARGET_TLV_NUM_VDEVS 4 +#define TARGET_TLV_NUM_STATIONS 32 +#define TARGET_TLV_NUM_PEERS 33 +#define TARGET_TLV_NUM_TDLS_VDEVS 1 +#define TARGET_TLV_NUM_TIDS ((TARGET_TLV_NUM_PEERS) * 2) +#define TARGET_TLV_NUM_MSDU_DESC (1024 + 32) +#define TARGET_TLV_NUM_MSDU_DESC_HL 1024 +#define TARGET_TLV_NUM_WOW_PATTERNS 22 +#define TARGET_TLV_MGMT_NUM_MSDU_DESC (50) + +/* Target specific defines for WMI-HL-1.0 firmware */ +#define TARGET_HL_TLV_NUM_PEERS 33 +#define TARGET_HL_TLV_AST_SKID_LIMIT 16 +#define TARGET_HL_TLV_NUM_WDS_ENTRIES 2 + +/* Target specific defines for QCA9377 high latency firmware */ +#define TARGET_QCA9377_HL_NUM_PEERS 15 + +/* Diagnostic Window */ +#define CE_DIAG_PIPE 7 + +#define NUM_TARGET_CE_CONFIG_WLAN ar->hw_values->num_target_ce_config_wlan + +/* Target specific defines for 10.4 firmware */ +#define TARGET_10_4_NUM_VDEVS 16 +#define TARGET_10_4_NUM_STATIONS 32 +#define TARGET_10_4_NUM_PEERS ((TARGET_10_4_NUM_STATIONS) + \ + (TARGET_10_4_NUM_VDEVS)) +#define TARGET_10_4_ACTIVE_PEERS 0 + +#define TARGET_10_4_NUM_QCACHE_PEERS_MAX 512 +#define TARGET_10_4_QCACHE_ACTIVE_PEERS 50 +#define TARGET_10_4_QCACHE_ACTIVE_PEERS_PFC 35 +#define TARGET_10_4_NUM_OFFLOAD_PEERS 0 +#define TARGET_10_4_NUM_OFFLOAD_REORDER_BUFFS 0 +#define TARGET_10_4_NUM_PEER_KEYS 2 +#define TARGET_10_4_TGT_NUM_TIDS ((TARGET_10_4_NUM_PEERS) * 2) +#define TARGET_10_4_NUM_MSDU_DESC (1024 + 400) +#define TARGET_10_4_NUM_MSDU_DESC_PFC 2500 +#define TARGET_10_4_AST_SKID_LIMIT 32 + +/* 100 ms for video, best-effort, and background */ +#define TARGET_10_4_RX_TIMEOUT_LO_PRI 100 + +/* 40 ms for voice */ +#define TARGET_10_4_RX_TIMEOUT_HI_PRI 40 + +#define TARGET_10_4_RX_DECAP_MODE ATH10K_HW_TXRX_NATIVE_WIFI +#define TARGET_10_4_SCAN_MAX_REQS 4 +#define TARGET_10_4_BMISS_OFFLOAD_MAX_VDEV 3 +#define TARGET_10_4_ROAM_OFFLOAD_MAX_VDEV 3 +#define TARGET_10_4_ROAM_OFFLOAD_MAX_PROFILES 8 + +/* Note: mcast to ucast is disabled by default */ +#define TARGET_10_4_NUM_MCAST_GROUPS 0 +#define TARGET_10_4_NUM_MCAST_TABLE_ELEMS 0 +#define TARGET_10_4_MCAST2UCAST_MODE 0 + +#define TARGET_10_4_TX_DBG_LOG_SIZE 1024 +#define TARGET_10_4_NUM_WDS_ENTRIES 32 +#define TARGET_10_4_DMA_BURST_SIZE 1 +#define TARGET_10_4_MAC_AGGR_DELIM 0 +#define TARGET_10_4_RX_SKIP_DEFRAG_TIMEOUT_DUP_DETECTION_CHECK 1 +#define TARGET_10_4_VOW_CONFIG 0 +#define TARGET_10_4_GTK_OFFLOAD_MAX_VDEV 3 +#define TARGET_10_4_11AC_TX_MAX_FRAGS 2 +#define TARGET_10_4_MAX_PEER_EXT_STATS 16 +#define TARGET_10_4_SMART_ANT_CAP 0 +#define TARGET_10_4_BK_MIN_FREE 0 +#define TARGET_10_4_BE_MIN_FREE 0 +#define TARGET_10_4_VI_MIN_FREE 0 +#define TARGET_10_4_VO_MIN_FREE 0 +#define TARGET_10_4_RX_BATCH_MODE 1 +#define TARGET_10_4_THERMAL_THROTTLING_CONFIG 0 +#define TARGET_10_4_ATF_CONFIG 0 +#define TARGET_10_4_IPHDR_PAD_CONFIG 1 +#define TARGET_10_4_QWRAP_CONFIG 0 + +/* TDLS config */ +#define TARGET_10_4_NUM_TDLS_VDEVS 1 +#define TARGET_10_4_NUM_TDLS_BUFFER_STA 1 +#define TARGET_10_4_NUM_TDLS_SLEEP_STA 1 + +/* Maximum number of Copy Engine's supported */ +#define CE_COUNT_MAX 12 + +/* Number of Copy Engines supported */ +#define CE_COUNT ar->hw_values->ce_count + +/* + * Granted MSIs are assigned as follows: + * Firmware uses the first + * Remaining MSIs, if any, are used by Copy Engines + * This mapping is known to both Target firmware and Host software. + * It may be changed as long as Host and Target are kept in sync. + */ +/* MSI for firmware (errors, etc.) */ +#define MSI_ASSIGN_FW 0 + +/* MSIs for Copy Engines */ +#define MSI_ASSIGN_CE_INITIAL 1 +#define MSI_ASSIGN_CE_MAX ar->hw_values->msi_assign_ce_max + +/* as of IP3.7.1 */ +#define RTC_STATE_V_ON ar->hw_values->rtc_state_val_on + +#define RTC_STATE_V_LSB 0 +#define RTC_STATE_V_MASK 0x00000007 +#define RTC_STATE_ADDRESS 0x0000 +#define PCIE_SOC_WAKE_V_MASK 0x00000001 +#define PCIE_SOC_WAKE_ADDRESS 0x0004 +#define PCIE_SOC_WAKE_RESET 0x00000000 +#define SOC_GLOBAL_RESET_ADDRESS 0x0008 + +#define RTC_SOC_BASE_ADDRESS ar->regs->rtc_soc_base_address +#define RTC_WMAC_BASE_ADDRESS ar->regs->rtc_wmac_base_address +#define MAC_COEX_BASE_ADDRESS 0x00006000 +#define BT_COEX_BASE_ADDRESS 0x00007000 +#define SOC_PCIE_BASE_ADDRESS 0x00008000 +#define SOC_CORE_BASE_ADDRESS ar->regs->soc_core_base_address +#define WLAN_UART_BASE_ADDRESS 0x0000c000 +#define WLAN_SI_BASE_ADDRESS 0x00010000 +#define WLAN_GPIO_BASE_ADDRESS 0x00014000 +#define WLAN_ANALOG_INTF_BASE_ADDRESS 0x0001c000 +#define WLAN_MAC_BASE_ADDRESS ar->regs->wlan_mac_base_address +#define EFUSE_BASE_ADDRESS 0x00030000 +#define FPGA_REG_BASE_ADDRESS 0x00039000 +#define WLAN_UART2_BASE_ADDRESS 0x00054c00 +#define CE_WRAPPER_BASE_ADDRESS ar->regs->ce_wrapper_base_address +#define CE0_BASE_ADDRESS ar->regs->ce0_base_address +#define CE1_BASE_ADDRESS ar->regs->ce1_base_address +#define CE2_BASE_ADDRESS ar->regs->ce2_base_address +#define CE3_BASE_ADDRESS ar->regs->ce3_base_address +#define CE4_BASE_ADDRESS ar->regs->ce4_base_address +#define CE5_BASE_ADDRESS ar->regs->ce5_base_address +#define CE6_BASE_ADDRESS ar->regs->ce6_base_address +#define CE7_BASE_ADDRESS ar->regs->ce7_base_address +#define DBI_BASE_ADDRESS 0x00060000 +#define WLAN_ANALOG_INTF_PCIE_BASE_ADDRESS 0x0006c000 +#define PCIE_LOCAL_BASE_ADDRESS ar->regs->pcie_local_base_address + +#define SOC_RESET_CONTROL_ADDRESS 0x00000000 +#define SOC_RESET_CONTROL_OFFSET 0x00000000 +#define SOC_RESET_CONTROL_SI0_RST_MASK ar->regs->soc_reset_control_si0_rst_mask +#define SOC_RESET_CONTROL_CE_RST_MASK ar->regs->soc_reset_control_ce_rst_mask +#define SOC_RESET_CONTROL_CPU_WARM_RST_MASK 0x00000040 +#define SOC_CPU_CLOCK_OFFSET 0x00000020 +#define SOC_CPU_CLOCK_STANDARD_LSB 0 +#define SOC_CPU_CLOCK_STANDARD_MASK 0x00000003 +#define SOC_CLOCK_CONTROL_OFFSET 0x00000028 +#define SOC_CLOCK_CONTROL_SI0_CLK_MASK 0x00000001 +#define SOC_SYSTEM_SLEEP_OFFSET 0x000000c4 +#define SOC_LPO_CAL_OFFSET 0x000000e0 +#define SOC_LPO_CAL_ENABLE_LSB 20 +#define SOC_LPO_CAL_ENABLE_MASK 0x00100000 +#define SOC_LF_TIMER_CONTROL0_ADDRESS 0x00000050 +#define SOC_LF_TIMER_CONTROL0_ENABLE_MASK 0x00000004 + +#define SOC_CHIP_ID_ADDRESS ar->regs->soc_chip_id_address +#define SOC_CHIP_ID_REV_LSB 8 +#define SOC_CHIP_ID_REV_MASK 0x00000f00 + +#define WLAN_RESET_CONTROL_COLD_RST_MASK 0x00000008 +#define WLAN_RESET_CONTROL_WARM_RST_MASK 0x00000004 +#define WLAN_SYSTEM_SLEEP_DISABLE_LSB 0 +#define WLAN_SYSTEM_SLEEP_DISABLE_MASK 0x00000001 + +#define WLAN_GPIO_PIN0_ADDRESS 0x00000028 +#define WLAN_GPIO_PIN0_CONFIG_LSB 11 +#define WLAN_GPIO_PIN0_CONFIG_MASK 0x00007800 +#define WLAN_GPIO_PIN0_PAD_PULL_LSB 5 +#define WLAN_GPIO_PIN0_PAD_PULL_MASK 0x00000060 +#define WLAN_GPIO_PIN1_ADDRESS 0x0000002c +#define WLAN_GPIO_PIN1_CONFIG_MASK 0x00007800 +#define WLAN_GPIO_PIN10_ADDRESS 0x00000050 +#define WLAN_GPIO_PIN11_ADDRESS 0x00000054 +#define WLAN_GPIO_PIN12_ADDRESS 0x00000058 +#define WLAN_GPIO_PIN13_ADDRESS 0x0000005c + +#define CLOCK_GPIO_OFFSET 0xffffffff +#define CLOCK_GPIO_BT_CLK_OUT_EN_LSB 0 +#define CLOCK_GPIO_BT_CLK_OUT_EN_MASK 0 + +#define SI_CONFIG_OFFSET 0x00000000 +#define SI_CONFIG_ERR_INT_LSB 19 +#define SI_CONFIG_ERR_INT_MASK 0x00080000 +#define SI_CONFIG_BIDIR_OD_DATA_LSB 18 +#define SI_CONFIG_BIDIR_OD_DATA_MASK 0x00040000 +#define SI_CONFIG_I2C_LSB 16 +#define SI_CONFIG_I2C_MASK 0x00010000 +#define SI_CONFIG_POS_SAMPLE_LSB 7 +#define SI_CONFIG_POS_SAMPLE_MASK 0x00000080 +#define SI_CONFIG_INACTIVE_DATA_LSB 5 +#define SI_CONFIG_INACTIVE_DATA_MASK 0x00000020 +#define SI_CONFIG_INACTIVE_CLK_LSB 4 +#define SI_CONFIG_INACTIVE_CLK_MASK 0x00000010 +#define SI_CONFIG_DIVIDER_LSB 0 +#define SI_CONFIG_DIVIDER_MASK 0x0000000f +#define SI_CS_OFFSET 0x00000004 +#define SI_CS_DONE_ERR_LSB 10 +#define SI_CS_DONE_ERR_MASK 0x00000400 +#define SI_CS_DONE_INT_LSB 9 +#define SI_CS_DONE_INT_MASK 0x00000200 +#define SI_CS_START_LSB 8 +#define SI_CS_START_MASK 0x00000100 +#define SI_CS_RX_CNT_LSB 4 +#define SI_CS_RX_CNT_MASK 0x000000f0 +#define SI_CS_TX_CNT_LSB 0 +#define SI_CS_TX_CNT_MASK 0x0000000f + +#define SI_TX_DATA0_OFFSET 0x00000008 +#define SI_TX_DATA1_OFFSET 0x0000000c +#define SI_RX_DATA0_OFFSET 0x00000010 +#define SI_RX_DATA1_OFFSET 0x00000014 + +#define CORE_CTRL_CPU_INTR_MASK 0x00002000 +#define CORE_CTRL_PCIE_REG_31_MASK 0x00000800 +#define CORE_CTRL_ADDRESS 0x0000 +#define PCIE_INTR_ENABLE_ADDRESS 0x0008 +#define PCIE_INTR_CAUSE_ADDRESS 0x000c +#define PCIE_INTR_CLR_ADDRESS ar->regs->pcie_intr_clr_address +#define SCRATCH_3_ADDRESS ar->regs->scratch_3_address +#define CPU_INTR_ADDRESS 0x0010 +#define FW_RAM_CONFIG_ADDRESS 0x0018 + +#define CCNT_TO_MSEC(ar, x) ((x) / ar->hw_params.channel_counters_freq_hz) + +/* Firmware indications to the Host via SCRATCH_3 register. */ +#define FW_INDICATOR_ADDRESS ar->regs->fw_indicator_address +#define FW_IND_EVENT_PENDING 1 +#define FW_IND_INITIALIZED 2 +#define FW_IND_HOST_READY 0x80000000 + +/* HOST_REG interrupt from firmware */ +#define PCIE_INTR_FIRMWARE_MASK ar->regs->pcie_intr_fw_mask +#define PCIE_INTR_CE_MASK_ALL ar->regs->pcie_intr_ce_mask_all + +#define DRAM_BASE_ADDRESS 0x00400000 + +#define PCIE_BAR_REG_ADDRESS 0x40030 + +#define MISSING 0 + +#define SYSTEM_SLEEP_OFFSET SOC_SYSTEM_SLEEP_OFFSET +#define WLAN_SYSTEM_SLEEP_OFFSET SOC_SYSTEM_SLEEP_OFFSET +#define WLAN_RESET_CONTROL_OFFSET SOC_RESET_CONTROL_OFFSET +#define CLOCK_CONTROL_OFFSET SOC_CLOCK_CONTROL_OFFSET +#define CLOCK_CONTROL_SI0_CLK_MASK SOC_CLOCK_CONTROL_SI0_CLK_MASK +#define RESET_CONTROL_MBOX_RST_MASK MISSING +#define RESET_CONTROL_SI0_RST_MASK SOC_RESET_CONTROL_SI0_RST_MASK +#define GPIO_BASE_ADDRESS WLAN_GPIO_BASE_ADDRESS +#define GPIO_PIN0_OFFSET WLAN_GPIO_PIN0_ADDRESS +#define GPIO_PIN1_OFFSET WLAN_GPIO_PIN1_ADDRESS +#define GPIO_PIN0_CONFIG_LSB WLAN_GPIO_PIN0_CONFIG_LSB +#define GPIO_PIN0_CONFIG_MASK WLAN_GPIO_PIN0_CONFIG_MASK +#define GPIO_PIN0_PAD_PULL_LSB WLAN_GPIO_PIN0_PAD_PULL_LSB +#define GPIO_PIN0_PAD_PULL_MASK WLAN_GPIO_PIN0_PAD_PULL_MASK +#define GPIO_PIN1_CONFIG_MASK WLAN_GPIO_PIN1_CONFIG_MASK +#define SI_BASE_ADDRESS WLAN_SI_BASE_ADDRESS +#define SCRATCH_BASE_ADDRESS SOC_CORE_BASE_ADDRESS +#define LOCAL_SCRATCH_OFFSET 0x18 +#define CPU_CLOCK_OFFSET SOC_CPU_CLOCK_OFFSET +#define LPO_CAL_OFFSET SOC_LPO_CAL_OFFSET +#define GPIO_PIN10_OFFSET WLAN_GPIO_PIN10_ADDRESS +#define GPIO_PIN11_OFFSET WLAN_GPIO_PIN11_ADDRESS +#define GPIO_PIN12_OFFSET WLAN_GPIO_PIN12_ADDRESS +#define GPIO_PIN13_OFFSET WLAN_GPIO_PIN13_ADDRESS +#define CPU_CLOCK_STANDARD_LSB SOC_CPU_CLOCK_STANDARD_LSB +#define CPU_CLOCK_STANDARD_MASK SOC_CPU_CLOCK_STANDARD_MASK +#define LPO_CAL_ENABLE_LSB SOC_LPO_CAL_ENABLE_LSB +#define LPO_CAL_ENABLE_MASK SOC_LPO_CAL_ENABLE_MASK +#define ANALOG_INTF_BASE_ADDRESS WLAN_ANALOG_INTF_BASE_ADDRESS +#define MBOX_BASE_ADDRESS MISSING +#define INT_STATUS_ENABLE_ERROR_LSB MISSING +#define INT_STATUS_ENABLE_ERROR_MASK MISSING +#define INT_STATUS_ENABLE_CPU_LSB MISSING +#define INT_STATUS_ENABLE_CPU_MASK MISSING +#define INT_STATUS_ENABLE_COUNTER_LSB MISSING +#define INT_STATUS_ENABLE_COUNTER_MASK MISSING +#define INT_STATUS_ENABLE_MBOX_DATA_LSB MISSING +#define INT_STATUS_ENABLE_MBOX_DATA_MASK MISSING +#define ERROR_STATUS_ENABLE_RX_UNDERFLOW_LSB MISSING +#define ERROR_STATUS_ENABLE_RX_UNDERFLOW_MASK MISSING +#define ERROR_STATUS_ENABLE_TX_OVERFLOW_LSB MISSING +#define ERROR_STATUS_ENABLE_TX_OVERFLOW_MASK MISSING +#define COUNTER_INT_STATUS_ENABLE_BIT_LSB MISSING +#define COUNTER_INT_STATUS_ENABLE_BIT_MASK MISSING +#define INT_STATUS_ENABLE_ADDRESS MISSING +#define CPU_INT_STATUS_ENABLE_BIT_LSB MISSING +#define CPU_INT_STATUS_ENABLE_BIT_MASK MISSING +#define HOST_INT_STATUS_ADDRESS MISSING +#define CPU_INT_STATUS_ADDRESS MISSING +#define ERROR_INT_STATUS_ADDRESS MISSING +#define ERROR_INT_STATUS_WAKEUP_MASK MISSING +#define ERROR_INT_STATUS_WAKEUP_LSB MISSING +#define ERROR_INT_STATUS_RX_UNDERFLOW_MASK MISSING +#define ERROR_INT_STATUS_RX_UNDERFLOW_LSB MISSING +#define ERROR_INT_STATUS_TX_OVERFLOW_MASK MISSING +#define ERROR_INT_STATUS_TX_OVERFLOW_LSB MISSING +#define COUNT_DEC_ADDRESS MISSING +#define HOST_INT_STATUS_CPU_MASK MISSING +#define HOST_INT_STATUS_CPU_LSB MISSING +#define HOST_INT_STATUS_ERROR_MASK MISSING +#define HOST_INT_STATUS_ERROR_LSB MISSING +#define HOST_INT_STATUS_COUNTER_MASK MISSING +#define HOST_INT_STATUS_COUNTER_LSB MISSING +#define RX_LOOKAHEAD_VALID_ADDRESS MISSING +#define WINDOW_DATA_ADDRESS MISSING +#define WINDOW_READ_ADDR_ADDRESS MISSING +#define WINDOW_WRITE_ADDR_ADDRESS MISSING + +#define QCA9887_1_0_I2C_SDA_GPIO_PIN 5 +#define QCA9887_1_0_I2C_SDA_PIN_CONFIG 3 +#define QCA9887_1_0_SI_CLK_GPIO_PIN 17 +#define QCA9887_1_0_SI_CLK_PIN_CONFIG 3 +#define QCA9887_1_0_GPIO_ENABLE_W1TS_LOW_ADDRESS 0x00000010 + +#define QCA9887_EEPROM_SELECT_READ 0xa10000a0 +#define QCA9887_EEPROM_ADDR_HI_MASK 0x0000ff00 +#define QCA9887_EEPROM_ADDR_HI_LSB 8 +#define QCA9887_EEPROM_ADDR_LO_MASK 0x00ff0000 +#define QCA9887_EEPROM_ADDR_LO_LSB 16 + +#define MBOX_RESET_CONTROL_ADDRESS 0x00000000 +#define MBOX_HOST_INT_STATUS_ADDRESS 0x00000800 +#define MBOX_HOST_INT_STATUS_ERROR_LSB 7 +#define MBOX_HOST_INT_STATUS_ERROR_MASK 0x00000080 +#define MBOX_HOST_INT_STATUS_CPU_LSB 6 +#define MBOX_HOST_INT_STATUS_CPU_MASK 0x00000040 +#define MBOX_HOST_INT_STATUS_COUNTER_LSB 4 +#define MBOX_HOST_INT_STATUS_COUNTER_MASK 0x00000010 +#define MBOX_CPU_INT_STATUS_ADDRESS 0x00000801 +#define MBOX_ERROR_INT_STATUS_ADDRESS 0x00000802 +#define MBOX_ERROR_INT_STATUS_WAKEUP_LSB 2 +#define MBOX_ERROR_INT_STATUS_WAKEUP_MASK 0x00000004 +#define MBOX_ERROR_INT_STATUS_RX_UNDERFLOW_LSB 1 +#define MBOX_ERROR_INT_STATUS_RX_UNDERFLOW_MASK 0x00000002 +#define MBOX_ERROR_INT_STATUS_TX_OVERFLOW_LSB 0 +#define MBOX_ERROR_INT_STATUS_TX_OVERFLOW_MASK 0x00000001 +#define MBOX_COUNTER_INT_STATUS_ADDRESS 0x00000803 +#define MBOX_COUNTER_INT_STATUS_COUNTER_LSB 0 +#define MBOX_COUNTER_INT_STATUS_COUNTER_MASK 0x000000ff +#define MBOX_RX_LOOKAHEAD_VALID_ADDRESS 0x00000805 +#define MBOX_INT_STATUS_ENABLE_ADDRESS 0x00000828 +#define MBOX_INT_STATUS_ENABLE_ERROR_LSB 7 +#define MBOX_INT_STATUS_ENABLE_ERROR_MASK 0x00000080 +#define MBOX_INT_STATUS_ENABLE_CPU_LSB 6 +#define MBOX_INT_STATUS_ENABLE_CPU_MASK 0x00000040 +#define MBOX_INT_STATUS_ENABLE_INT_LSB 5 +#define MBOX_INT_STATUS_ENABLE_INT_MASK 0x00000020 +#define MBOX_INT_STATUS_ENABLE_COUNTER_LSB 4 +#define MBOX_INT_STATUS_ENABLE_COUNTER_MASK 0x00000010 +#define MBOX_INT_STATUS_ENABLE_MBOX_DATA_LSB 0 +#define MBOX_INT_STATUS_ENABLE_MBOX_DATA_MASK 0x0000000f +#define MBOX_CPU_INT_STATUS_ENABLE_ADDRESS 0x00000819 +#define MBOX_CPU_INT_STATUS_ENABLE_BIT_LSB 0 +#define MBOX_CPU_INT_STATUS_ENABLE_BIT_MASK 0x000000ff +#define MBOX_CPU_STATUS_ENABLE_ASSERT_MASK 0x00000001 +#define MBOX_ERROR_STATUS_ENABLE_ADDRESS 0x0000081a +#define MBOX_ERROR_STATUS_ENABLE_RX_UNDERFLOW_LSB 1 +#define MBOX_ERROR_STATUS_ENABLE_RX_UNDERFLOW_MASK 0x00000002 +#define MBOX_ERROR_STATUS_ENABLE_TX_OVERFLOW_LSB 0 +#define MBOX_ERROR_STATUS_ENABLE_TX_OVERFLOW_MASK 0x00000001 +#define MBOX_COUNTER_INT_STATUS_ENABLE_ADDRESS 0x0000081b +#define MBOX_COUNTER_INT_STATUS_ENABLE_BIT_LSB 0 +#define MBOX_COUNTER_INT_STATUS_ENABLE_BIT_MASK 0x000000ff +#define MBOX_COUNT_ADDRESS 0x00000820 +#define MBOX_COUNT_DEC_ADDRESS 0x00000840 +#define MBOX_WINDOW_DATA_ADDRESS 0x00000874 +#define MBOX_WINDOW_WRITE_ADDR_ADDRESS 0x00000878 +#define MBOX_WINDOW_READ_ADDR_ADDRESS 0x0000087c +#define MBOX_CPU_DBG_SEL_ADDRESS 0x00000883 +#define MBOX_CPU_DBG_ADDRESS 0x00000884 +#define MBOX_RTC_BASE_ADDRESS 0x00000000 +#define MBOX_GPIO_BASE_ADDRESS 0x00005000 +#define MBOX_MBOX_BASE_ADDRESS 0x00008000 + +#define RTC_STATE_V_GET(x) (((x) & RTC_STATE_V_MASK) >> RTC_STATE_V_LSB) + +/* Register definitions for first generation ath10k cards. These cards include + * a mac thich has a register allocation similar to ath9k and at least some + * registers including the ones relevant for modifying the coverage class are + * identical to the ath9k definitions. + * These registers are usually managed by the ath10k firmware. However by + * overriding them it is possible to support coverage class modifications. + */ +#define WAVE1_PCU_ACK_CTS_TIMEOUT 0x8014 +#define WAVE1_PCU_ACK_CTS_TIMEOUT_MAX 0x00003FFF +#define WAVE1_PCU_ACK_CTS_TIMEOUT_ACK_MASK 0x00003FFF +#define WAVE1_PCU_ACK_CTS_TIMEOUT_ACK_LSB 0 +#define WAVE1_PCU_ACK_CTS_TIMEOUT_CTS_MASK 0x3FFF0000 +#define WAVE1_PCU_ACK_CTS_TIMEOUT_CTS_LSB 16 + +#define WAVE1_PCU_GBL_IFS_SLOT 0x1070 +#define WAVE1_PCU_GBL_IFS_SLOT_MASK 0x0000FFFF +#define WAVE1_PCU_GBL_IFS_SLOT_MAX 0x0000FFFF +#define WAVE1_PCU_GBL_IFS_SLOT_LSB 0 +#define WAVE1_PCU_GBL_IFS_SLOT_RESV0 0xFFFF0000 + +#define WAVE1_PHYCLK 0x801C +#define WAVE1_PHYCLK_USEC_MASK 0x0000007F +#define WAVE1_PHYCLK_USEC_LSB 0 + +/* qca6174 PLL offset/mask */ +#define SOC_CORE_CLK_CTRL_OFFSET 0x00000114 +#define SOC_CORE_CLK_CTRL_DIV_LSB 0 +#define SOC_CORE_CLK_CTRL_DIV_MASK 0x00000007 + +#define EFUSE_OFFSET 0x0000032c +#define EFUSE_XTAL_SEL_LSB 8 +#define EFUSE_XTAL_SEL_MASK 0x00000700 + +#define BB_PLL_CONFIG_OFFSET 0x000002f4 +#define BB_PLL_CONFIG_FRAC_LSB 0 +#define BB_PLL_CONFIG_FRAC_MASK 0x0003ffff +#define BB_PLL_CONFIG_OUTDIV_LSB 18 +#define BB_PLL_CONFIG_OUTDIV_MASK 0x001c0000 + +#define WLAN_PLL_SETTLE_OFFSET 0x0018 +#define WLAN_PLL_SETTLE_TIME_LSB 0 +#define WLAN_PLL_SETTLE_TIME_MASK 0x000007ff + +#define WLAN_PLL_CONTROL_OFFSET 0x0014 +#define WLAN_PLL_CONTROL_DIV_LSB 0 +#define WLAN_PLL_CONTROL_DIV_MASK 0x000003ff +#define WLAN_PLL_CONTROL_REFDIV_LSB 10 +#define WLAN_PLL_CONTROL_REFDIV_MASK 0x00003c00 +#define WLAN_PLL_CONTROL_BYPASS_LSB 16 +#define WLAN_PLL_CONTROL_BYPASS_MASK 0x00010000 +#define WLAN_PLL_CONTROL_NOPWD_LSB 18 +#define WLAN_PLL_CONTROL_NOPWD_MASK 0x00040000 + +#define RTC_SYNC_STATUS_OFFSET 0x0244 +#define RTC_SYNC_STATUS_PLL_CHANGING_LSB 5 +#define RTC_SYNC_STATUS_PLL_CHANGING_MASK 0x00000020 +/* qca6174 PLL offset/mask end */ + +/* CPU_ADDR_MSB is a register, bit[3:0] is to specify which memory + * region is accessed. The memory region size is 1M. + * If host wants to access 0xX12345 at target, then CPU_ADDR_MSB[3:0] + * is 0xX. + * The following MACROs are defined to get the 0xX and the size limit. + */ +#define CPU_ADDR_MSB_REGION_MASK GENMASK(23, 20) +#define CPU_ADDR_MSB_REGION_VAL(X) FIELD_GET(CPU_ADDR_MSB_REGION_MASK, X) +#define REGION_ACCESS_SIZE_LIMIT 0x100000 +#define REGION_ACCESS_SIZE_MASK (REGION_ACCESS_SIZE_LIMIT - 1) + +#endif /* _HW_H_ */ -- cgit v1.2.3