From ace9429bb58fd418f0c81d4c2835699bddf6bde6 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Thu, 11 Apr 2024 10:27:49 +0200 Subject: Adding upstream version 6.6.15. Signed-off-by: Daniel Baumann --- drivers/pci/quirks.c | 6229 ++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 6229 insertions(+) create mode 100644 drivers/pci/quirks.c (limited to 'drivers/pci/quirks.c') diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c new file mode 100644 index 0000000000..e008191405 --- /dev/null +++ b/drivers/pci/quirks.c @@ -0,0 +1,6229 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * This file contains work-arounds for many known PCI hardware bugs. + * Devices present only on certain architectures (host bridges et cetera) + * should be handled in arch-specific code. + * + * Note: any quirks for hotpluggable devices must _NOT_ be declared __init. + * + * Copyright (c) 1999 Martin Mares + * + * Init/reset quirks for USB host controllers should be in the USB quirks + * file, where their drivers can use them. + */ + +#include +#include +#include +#include +#include +#include /* isa_dma_bridge_buggy */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "pci.h" + +/* + * Retrain the link of a downstream PCIe port by hand if necessary. + * + * This is needed at least where a downstream port of the ASMedia ASM2824 + * Gen 3 switch is wired to the upstream port of the Pericom PI7C9X2G304 + * Gen 2 switch, and observed with the Delock Riser Card PCI Express x1 > + * 2 x PCIe x1 device, P/N 41433, plugged into the SiFive HiFive Unmatched + * board. + * + * In such a configuration the switches are supposed to negotiate the link + * speed of preferably 5.0GT/s, falling back to 2.5GT/s. However the link + * continues switching between the two speeds indefinitely and the data + * link layer never reaches the active state, with link training reported + * repeatedly active ~84% of the time. Forcing the target link speed to + * 2.5GT/s with the upstream ASM2824 device makes the two switches talk to + * each other correctly however. And more interestingly retraining with a + * higher target link speed afterwards lets the two successfully negotiate + * 5.0GT/s. + * + * With the ASM2824 we can rely on the otherwise optional Data Link Layer + * Link Active status bit and in the failed link training scenario it will + * be off along with the Link Bandwidth Management Status indicating that + * hardware has changed the link speed or width in an attempt to correct + * unreliable link operation. For a port that has been left unconnected + * both bits will be clear. So use this information to detect the problem + * rather than polling the Link Training bit and watching out for flips or + * at least the active status. + * + * Since the exact nature of the problem isn't known and in principle this + * could trigger where an ASM2824 device is downstream rather upstream, + * apply this erratum workaround to any downstream ports as long as they + * support Link Active reporting and have the Link Control 2 register. + * Restrict the speed to 2.5GT/s then with the Target Link Speed field, + * request a retrain and wait 200ms for the data link to go up. + * + * If this turns out successful and we know by the Vendor:Device ID it is + * safe to do so, then lift the restriction, letting the devices negotiate + * a higher speed. Also check for a similar 2.5GT/s speed restriction the + * firmware may have already arranged and lift it with ports that already + * report their data link being up. + * + * Return TRUE if the link has been successfully retrained, otherwise FALSE. + */ +bool pcie_failed_link_retrain(struct pci_dev *dev) +{ + static const struct pci_device_id ids[] = { + { PCI_VDEVICE(ASMEDIA, 0x2824) }, /* ASMedia ASM2824 */ + {} + }; + u16 lnksta, lnkctl2; + + if (!pci_is_pcie(dev) || !pcie_downstream_port(dev) || + !pcie_cap_has_lnkctl2(dev) || !dev->link_active_reporting) + return false; + + pcie_capability_read_word(dev, PCI_EXP_LNKCTL2, &lnkctl2); + pcie_capability_read_word(dev, PCI_EXP_LNKSTA, &lnksta); + if ((lnksta & (PCI_EXP_LNKSTA_LBMS | PCI_EXP_LNKSTA_DLLLA)) == + PCI_EXP_LNKSTA_LBMS) { + pci_info(dev, "broken device, retraining non-functional downstream link at 2.5GT/s\n"); + + lnkctl2 &= ~PCI_EXP_LNKCTL2_TLS; + lnkctl2 |= PCI_EXP_LNKCTL2_TLS_2_5GT; + pcie_capability_write_word(dev, PCI_EXP_LNKCTL2, lnkctl2); + + if (pcie_retrain_link(dev, false)) { + pci_info(dev, "retraining failed\n"); + return false; + } + + pcie_capability_read_word(dev, PCI_EXP_LNKSTA, &lnksta); + } + + if ((lnksta & PCI_EXP_LNKSTA_DLLLA) && + (lnkctl2 & PCI_EXP_LNKCTL2_TLS) == PCI_EXP_LNKCTL2_TLS_2_5GT && + pci_match_id(ids, dev)) { + u32 lnkcap; + + pci_info(dev, "removing 2.5GT/s downstream link speed restriction\n"); + pcie_capability_read_dword(dev, PCI_EXP_LNKCAP, &lnkcap); + lnkctl2 &= ~PCI_EXP_LNKCTL2_TLS; + lnkctl2 |= lnkcap & PCI_EXP_LNKCAP_SLS; + pcie_capability_write_word(dev, PCI_EXP_LNKCTL2, lnkctl2); + + if (pcie_retrain_link(dev, false)) { + pci_info(dev, "retraining failed\n"); + return false; + } + } + + return true; +} + +static ktime_t fixup_debug_start(struct pci_dev *dev, + void (*fn)(struct pci_dev *dev)) +{ + if (initcall_debug) + pci_info(dev, "calling %pS @ %i\n", fn, task_pid_nr(current)); + + return ktime_get(); +} + +static void fixup_debug_report(struct pci_dev *dev, ktime_t calltime, + void (*fn)(struct pci_dev *dev)) +{ + ktime_t delta, rettime; + unsigned long long duration; + + rettime = ktime_get(); + delta = ktime_sub(rettime, calltime); + duration = (unsigned long long) ktime_to_ns(delta) >> 10; + if (initcall_debug || duration > 10000) + pci_info(dev, "%pS took %lld usecs\n", fn, duration); +} + +static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f, + struct pci_fixup *end) +{ + ktime_t calltime; + + for (; f < end; f++) + if ((f->class == (u32) (dev->class >> f->class_shift) || + f->class == (u32) PCI_ANY_ID) && + (f->vendor == dev->vendor || + f->vendor == (u16) PCI_ANY_ID) && + (f->device == dev->device || + f->device == (u16) PCI_ANY_ID)) { + void (*hook)(struct pci_dev *dev); +#ifdef CONFIG_HAVE_ARCH_PREL32_RELOCATIONS + hook = offset_to_ptr(&f->hook_offset); +#else + hook = f->hook; +#endif + calltime = fixup_debug_start(dev, hook); + hook(dev); + fixup_debug_report(dev, calltime, hook); + } +} + +extern struct pci_fixup __start_pci_fixups_early[]; +extern struct pci_fixup __end_pci_fixups_early[]; +extern struct pci_fixup __start_pci_fixups_header[]; +extern struct pci_fixup __end_pci_fixups_header[]; +extern struct pci_fixup __start_pci_fixups_final[]; +extern struct pci_fixup __end_pci_fixups_final[]; +extern struct pci_fixup __start_pci_fixups_enable[]; +extern struct pci_fixup __end_pci_fixups_enable[]; +extern struct pci_fixup __start_pci_fixups_resume[]; +extern struct pci_fixup __end_pci_fixups_resume[]; +extern struct pci_fixup __start_pci_fixups_resume_early[]; +extern struct pci_fixup __end_pci_fixups_resume_early[]; +extern struct pci_fixup __start_pci_fixups_suspend[]; +extern struct pci_fixup __end_pci_fixups_suspend[]; +extern struct pci_fixup __start_pci_fixups_suspend_late[]; +extern struct pci_fixup __end_pci_fixups_suspend_late[]; + +static bool pci_apply_fixup_final_quirks; + +void pci_fixup_device(enum pci_fixup_pass pass, struct pci_dev *dev) +{ + struct pci_fixup *start, *end; + + switch (pass) { + case pci_fixup_early: + start = __start_pci_fixups_early; + end = __end_pci_fixups_early; + break; + + case pci_fixup_header: + start = __start_pci_fixups_header; + end = __end_pci_fixups_header; + break; + + case pci_fixup_final: + if (!pci_apply_fixup_final_quirks) + return; + start = __start_pci_fixups_final; + end = __end_pci_fixups_final; + break; + + case pci_fixup_enable: + start = __start_pci_fixups_enable; + end = __end_pci_fixups_enable; + break; + + case pci_fixup_resume: + start = __start_pci_fixups_resume; + end = __end_pci_fixups_resume; + break; + + case pci_fixup_resume_early: + start = __start_pci_fixups_resume_early; + end = __end_pci_fixups_resume_early; + break; + + case pci_fixup_suspend: + start = __start_pci_fixups_suspend; + end = __end_pci_fixups_suspend; + break; + + case pci_fixup_suspend_late: + start = __start_pci_fixups_suspend_late; + end = __end_pci_fixups_suspend_late; + break; + + default: + /* stupid compiler warning, you would think with an enum... */ + return; + } + pci_do_fixups(dev, start, end); +} +EXPORT_SYMBOL(pci_fixup_device); + +static int __init pci_apply_final_quirks(void) +{ + struct pci_dev *dev = NULL; + u8 cls = 0; + u8 tmp; + + if (pci_cache_line_size) + pr_info("PCI: CLS %u bytes\n", pci_cache_line_size << 2); + + pci_apply_fixup_final_quirks = true; + for_each_pci_dev(dev) { + pci_fixup_device(pci_fixup_final, dev); + /* + * If arch hasn't set it explicitly yet, use the CLS + * value shared by all PCI devices. If there's a + * mismatch, fall back to the default value. + */ + if (!pci_cache_line_size) { + pci_read_config_byte(dev, PCI_CACHE_LINE_SIZE, &tmp); + if (!cls) + cls = tmp; + if (!tmp || cls == tmp) + continue; + + pci_info(dev, "CLS mismatch (%u != %u), using %u bytes\n", + cls << 2, tmp << 2, + pci_dfl_cache_line_size << 2); + pci_cache_line_size = pci_dfl_cache_line_size; + } + } + + if (!pci_cache_line_size) { + pr_info("PCI: CLS %u bytes, default %u\n", cls << 2, + pci_dfl_cache_line_size << 2); + pci_cache_line_size = cls ? cls : pci_dfl_cache_line_size; + } + + return 0; +} +fs_initcall_sync(pci_apply_final_quirks); + +/* + * Decoding should be disabled for a PCI device during BAR sizing to avoid + * conflict. But doing so may cause problems on host bridge and perhaps other + * key system devices. For devices that need to have mmio decoding always-on, + * we need to set the dev->mmio_always_on bit. + */ +static void quirk_mmio_always_on(struct pci_dev *dev) +{ + dev->mmio_always_on = 1; +} +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_ANY_ID, PCI_ANY_ID, + PCI_CLASS_BRIDGE_HOST, 8, quirk_mmio_always_on); + +/* + * The Mellanox Tavor device gives false positive parity errors. Disable + * parity error reporting. + */ +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_MELLANOX, PCI_DEVICE_ID_MELLANOX_TAVOR, pci_disable_parity); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_MELLANOX, PCI_DEVICE_ID_MELLANOX_TAVOR_BRIDGE, pci_disable_parity); + +/* + * Deal with broken BIOSes that neglect to enable passive release, + * which can cause problems in combination with the 82441FX/PPro MTRRs + */ +static void quirk_passive_release(struct pci_dev *dev) +{ + struct pci_dev *d = NULL; + unsigned char dlc; + + /* + * We have to make sure a particular bit is set in the PIIX3 + * ISA bridge, so we have to go out and find it. + */ + while ((d = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_0, d))) { + pci_read_config_byte(d, 0x82, &dlc); + if (!(dlc & 1<<1)) { + pci_info(d, "PIIX3: Enabling Passive Release\n"); + dlc |= 1<<1; + pci_write_config_byte(d, 0x82, dlc); + } + } +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_passive_release); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_passive_release); + +#ifdef CONFIG_X86_32 +/* + * The VIA VP2/VP3/MVP3 seem to have some 'features'. There may be a + * workaround but VIA don't answer queries. If you happen to have good + * contacts at VIA ask them for me please -- Alan + * + * This appears to be BIOS not version dependent. So presumably there is a + * chipset level fix. + */ +static void quirk_isa_dma_hangs(struct pci_dev *dev) +{ + if (!isa_dma_bridge_buggy) { + isa_dma_bridge_buggy = 1; + pci_info(dev, "Activating ISA DMA hang workarounds\n"); + } +} +/* + * It's not totally clear which chipsets are the problematic ones. We know + * 82C586 and 82C596 variants are affected. + */ +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_0, quirk_isa_dma_hangs); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C596, quirk_isa_dma_hangs); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_0, quirk_isa_dma_hangs); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, quirk_isa_dma_hangs); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_1, quirk_isa_dma_hangs); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_2, quirk_isa_dma_hangs); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_3, quirk_isa_dma_hangs); +#endif + +#ifdef CONFIG_HAS_IOPORT +/* + * Intel NM10 "Tiger Point" LPC PM1a_STS.BM_STS must be clear + * for some HT machines to use C4 w/o hanging. + */ +static void quirk_tigerpoint_bm_sts(struct pci_dev *dev) +{ + u32 pmbase; + u16 pm1a; + + pci_read_config_dword(dev, 0x40, &pmbase); + pmbase = pmbase & 0xff80; + pm1a = inw(pmbase); + + if (pm1a & 0x10) { + pci_info(dev, FW_BUG "Tiger Point LPC.BM_STS cleared\n"); + outw(0x10, pmbase); + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_TGP_LPC, quirk_tigerpoint_bm_sts); +#endif + +/* Chipsets where PCI->PCI transfers vanish or hang */ +static void quirk_nopcipci(struct pci_dev *dev) +{ + if ((pci_pci_problems & PCIPCI_FAIL) == 0) { + pci_info(dev, "Disabling direct PCI/PCI transfers\n"); + pci_pci_problems |= PCIPCI_FAIL; + } +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_5597, quirk_nopcipci); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_496, quirk_nopcipci); + +static void quirk_nopciamd(struct pci_dev *dev) +{ + u8 rev; + pci_read_config_byte(dev, 0x08, &rev); + if (rev == 0x13) { + /* Erratum 24 */ + pci_info(dev, "Chipset erratum: Disabling direct PCI/AGP transfers\n"); + pci_pci_problems |= PCIAGP_FAIL; + } +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8151_0, quirk_nopciamd); + +/* Triton requires workarounds to be used by the drivers */ +static void quirk_triton(struct pci_dev *dev) +{ + if ((pci_pci_problems&PCIPCI_TRITON) == 0) { + pci_info(dev, "Limiting direct PCI/PCI transfers\n"); + pci_pci_problems |= PCIPCI_TRITON; + } +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82437, quirk_triton); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82437VX, quirk_triton); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82439, quirk_triton); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82439TX, quirk_triton); + +/* + * VIA Apollo KT133 needs PCI latency patch + * Made according to a Windows driver-based patch by George E. Breese; + * see PCI Latency Adjust on http://www.viahardware.com/download/viatweak.shtm + * Also see http://www.au-ja.org/review-kt133a-1-en.phtml for the info on + * which Mr Breese based his work. + * + * Updated based on further information from the site and also on + * information provided by VIA + */ +static void quirk_vialatency(struct pci_dev *dev) +{ + struct pci_dev *p; + u8 busarb; + + /* + * Ok, we have a potential problem chipset here. Now see if we have + * a buggy southbridge. + */ + p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, NULL); + if (p != NULL) { + + /* + * 0x40 - 0x4f == 686B, 0x10 - 0x2f == 686A; + * thanks Dan Hollis. + * Check for buggy part revisions + */ + if (p->revision < 0x40 || p->revision > 0x42) + goto exit; + } else { + p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, NULL); + if (p == NULL) /* No problem parts */ + goto exit; + + /* Check for buggy part revisions */ + if (p->revision < 0x10 || p->revision > 0x12) + goto exit; + } + + /* + * Ok we have the problem. Now set the PCI master grant to occur + * every master grant. The apparent bug is that under high PCI load + * (quite common in Linux of course) you can get data loss when the + * CPU is held off the bus for 3 bus master requests. This happens + * to include the IDE controllers.... + * + * VIA only apply this fix when an SB Live! is present but under + * both Linux and Windows this isn't enough, and we have seen + * corruption without SB Live! but with things like 3 UDMA IDE + * controllers. So we ignore that bit of the VIA recommendation.. + */ + pci_read_config_byte(dev, 0x76, &busarb); + + /* + * Set bit 4 and bit 5 of byte 76 to 0x01 + * "Master priority rotation on every PCI master grant" + */ + busarb &= ~(1<<5); + busarb |= (1<<4); + pci_write_config_byte(dev, 0x76, busarb); + pci_info(dev, "Applying VIA southbridge workaround\n"); +exit: + pci_dev_put(p); +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, quirk_vialatency); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8371_1, quirk_vialatency); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, quirk_vialatency); +/* Must restore this on a resume from RAM */ +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, quirk_vialatency); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8371_1, quirk_vialatency); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, quirk_vialatency); + +/* VIA Apollo VP3 needs ETBF on BT848/878 */ +static void quirk_viaetbf(struct pci_dev *dev) +{ + if ((pci_pci_problems&PCIPCI_VIAETBF) == 0) { + pci_info(dev, "Limiting direct PCI/PCI transfers\n"); + pci_pci_problems |= PCIPCI_VIAETBF; + } +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C597_0, quirk_viaetbf); + +static void quirk_vsfx(struct pci_dev *dev) +{ + if ((pci_pci_problems&PCIPCI_VSFX) == 0) { + pci_info(dev, "Limiting direct PCI/PCI transfers\n"); + pci_pci_problems |= PCIPCI_VSFX; + } +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C576, quirk_vsfx); + +/* + * ALi Magik requires workarounds to be used by the drivers that DMA to AGP + * space. Latency must be set to 0xA and Triton workaround applied too. + * [Info kindly provided by ALi] + */ +static void quirk_alimagik(struct pci_dev *dev) +{ + if ((pci_pci_problems&PCIPCI_ALIMAGIK) == 0) { + pci_info(dev, "Limiting direct PCI/PCI transfers\n"); + pci_pci_problems |= PCIPCI_ALIMAGIK|PCIPCI_TRITON; + } +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1647, quirk_alimagik); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1651, quirk_alimagik); + +/* Natoma has some interesting boundary conditions with Zoran stuff at least */ +static void quirk_natoma(struct pci_dev *dev) +{ + if ((pci_pci_problems&PCIPCI_NATOMA) == 0) { + pci_info(dev, "Limiting direct PCI/PCI transfers\n"); + pci_pci_problems |= PCIPCI_NATOMA; + } +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_natoma); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443LX_0, quirk_natoma); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443LX_1, quirk_natoma); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_0, quirk_natoma); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_1, quirk_natoma); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_2, quirk_natoma); + +/* + * This chip can cause PCI parity errors if config register 0xA0 is read + * while DMAs are occurring. + */ +static void quirk_citrine(struct pci_dev *dev) +{ + dev->cfg_size = 0xA0; +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_IBM, PCI_DEVICE_ID_IBM_CITRINE, quirk_citrine); + +/* + * This chip can cause bus lockups if config addresses above 0x600 + * are read or written. + */ +static void quirk_nfp6000(struct pci_dev *dev) +{ + dev->cfg_size = 0x600; +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NETRONOME, PCI_DEVICE_ID_NETRONOME_NFP4000, quirk_nfp6000); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NETRONOME, PCI_DEVICE_ID_NETRONOME_NFP6000, quirk_nfp6000); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NETRONOME, PCI_DEVICE_ID_NETRONOME_NFP5000, quirk_nfp6000); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NETRONOME, PCI_DEVICE_ID_NETRONOME_NFP6000_VF, quirk_nfp6000); + +/* On IBM Crocodile ipr SAS adapters, expand BAR to system page size */ +static void quirk_extend_bar_to_page(struct pci_dev *dev) +{ + int i; + + for (i = 0; i < PCI_STD_NUM_BARS; i++) { + struct resource *r = &dev->resource[i]; + + if (r->flags & IORESOURCE_MEM && resource_size(r) < PAGE_SIZE) { + r->end = PAGE_SIZE - 1; + r->start = 0; + r->flags |= IORESOURCE_UNSET; + pci_info(dev, "expanded BAR %d to page size: %pR\n", + i, r); + } + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_IBM, 0x034a, quirk_extend_bar_to_page); + +/* + * S3 868 and 968 chips report region size equal to 32M, but they decode 64M. + * If it's needed, re-allocate the region. + */ +static void quirk_s3_64M(struct pci_dev *dev) +{ + struct resource *r = &dev->resource[0]; + + if ((r->start & 0x3ffffff) || r->end != r->start + 0x3ffffff) { + r->flags |= IORESOURCE_UNSET; + r->start = 0; + r->end = 0x3ffffff; + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_868, quirk_s3_64M); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_968, quirk_s3_64M); + +static void quirk_io(struct pci_dev *dev, int pos, unsigned int size, + const char *name) +{ + u32 region; + struct pci_bus_region bus_region; + struct resource *res = dev->resource + pos; + + pci_read_config_dword(dev, PCI_BASE_ADDRESS_0 + (pos << 2), ®ion); + + if (!region) + return; + + res->name = pci_name(dev); + res->flags = region & ~PCI_BASE_ADDRESS_IO_MASK; + res->flags |= + (IORESOURCE_IO | IORESOURCE_PCI_FIXED | IORESOURCE_SIZEALIGN); + region &= ~(size - 1); + + /* Convert from PCI bus to resource space */ + bus_region.start = region; + bus_region.end = region + size - 1; + pcibios_bus_to_resource(dev->bus, res, &bus_region); + + pci_info(dev, FW_BUG "%s quirk: reg 0x%x: %pR\n", + name, PCI_BASE_ADDRESS_0 + (pos << 2), res); +} + +/* + * Some CS5536 BIOSes (for example, the Soekris NET5501 board w/ comBIOS + * ver. 1.33 20070103) don't set the correct ISA PCI region header info. + * BAR0 should be 8 bytes; instead, it may be set to something like 8k + * (which conflicts w/ BAR1's memory range). + * + * CS553x's ISA PCI BARs may also be read-only (ref: + * https://bugzilla.kernel.org/show_bug.cgi?id=85991 - Comment #4 forward). + */ +static void quirk_cs5536_vsa(struct pci_dev *dev) +{ + static char *name = "CS5536 ISA bridge"; + + if (pci_resource_len(dev, 0) != 8) { + quirk_io(dev, 0, 8, name); /* SMB */ + quirk_io(dev, 1, 256, name); /* GPIO */ + quirk_io(dev, 2, 64, name); /* MFGPT */ + pci_info(dev, "%s bug detected (incorrect header); workaround applied\n", + name); + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA, quirk_cs5536_vsa); + +static void quirk_io_region(struct pci_dev *dev, int port, + unsigned int size, int nr, const char *name) +{ + u16 region; + struct pci_bus_region bus_region; + struct resource *res = dev->resource + nr; + + pci_read_config_word(dev, port, ®ion); + region &= ~(size - 1); + + if (!region) + return; + + res->name = pci_name(dev); + res->flags = IORESOURCE_IO; + + /* Convert from PCI bus to resource space */ + bus_region.start = region; + bus_region.end = region + size - 1; + pcibios_bus_to_resource(dev->bus, res, &bus_region); + + if (!pci_claim_resource(dev, nr)) + pci_info(dev, "quirk: %pR claimed by %s\n", res, name); +} + +/* + * ATI Northbridge setups MCE the processor if you even read somewhere + * between 0x3b0->0x3bb or read 0x3d3 + */ +static void quirk_ati_exploding_mce(struct pci_dev *dev) +{ + pci_info(dev, "ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb\n"); + /* Mae rhaid i ni beidio ag edrych ar y lleoliadiau I/O hyn */ + request_region(0x3b0, 0x0C, "RadeonIGP"); + request_region(0x3d3, 0x01, "RadeonIGP"); +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS100, quirk_ati_exploding_mce); + +/* + * In the AMD NL platform, this device ([1022:7912]) has a class code of + * PCI_CLASS_SERIAL_USB_XHCI (0x0c0330), which means the xhci driver will + * claim it. The same applies on the VanGogh platform device ([1022:163a]). + * + * But the dwc3 driver is a more specific driver for this device, and we'd + * prefer to use it instead of xhci. To prevent xhci from claiming the + * device, change the class code to 0x0c03fe, which the PCI r3.0 spec + * defines as "USB device (not host controller)". The dwc3 driver can then + * claim it based on its Vendor and Device ID. + */ +static void quirk_amd_dwc_class(struct pci_dev *pdev) +{ + u32 class = pdev->class; + + /* Use "USB Device (not host controller)" class */ + pdev->class = PCI_CLASS_SERIAL_USB_DEVICE; + pci_info(pdev, "PCI class overridden (%#08x -> %#08x) so dwc3 driver can claim this instead of xhci\n", + class, pdev->class); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_NL_USB, + quirk_amd_dwc_class); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VANGOGH_USB, + quirk_amd_dwc_class); + +/* + * Synopsys USB 3.x host HAPS platform has a class code of + * PCI_CLASS_SERIAL_USB_XHCI, and xhci driver can claim it. However, these + * devices should use dwc3-haps driver. Change these devices' class code to + * PCI_CLASS_SERIAL_USB_DEVICE to prevent the xhci-pci driver from claiming + * them. + */ +static void quirk_synopsys_haps(struct pci_dev *pdev) +{ + u32 class = pdev->class; + + switch (pdev->device) { + case PCI_DEVICE_ID_SYNOPSYS_HAPSUSB3: + case PCI_DEVICE_ID_SYNOPSYS_HAPSUSB3_AXI: + case PCI_DEVICE_ID_SYNOPSYS_HAPSUSB31: + pdev->class = PCI_CLASS_SERIAL_USB_DEVICE; + pci_info(pdev, "PCI class overridden (%#08x -> %#08x) so dwc3 driver can claim this instead of xhci\n", + class, pdev->class); + break; + } +} +DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_VENDOR_ID_SYNOPSYS, PCI_ANY_ID, + PCI_CLASS_SERIAL_USB_XHCI, 0, + quirk_synopsys_haps); + +/* + * Let's make the southbridge information explicit instead of having to + * worry about people probing the ACPI areas, for example.. (Yes, it + * happens, and if you read the wrong ACPI register it will put the machine + * to sleep with no way of waking it up again. Bummer). + * + * ALI M7101: Two IO regions pointed to by words at + * 0xE0 (64 bytes of ACPI registers) + * 0xE2 (32 bytes of SMB registers) + */ +static void quirk_ali7101_acpi(struct pci_dev *dev) +{ + quirk_io_region(dev, 0xE0, 64, PCI_BRIDGE_RESOURCES, "ali7101 ACPI"); + quirk_io_region(dev, 0xE2, 32, PCI_BRIDGE_RESOURCES+1, "ali7101 SMB"); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M7101, quirk_ali7101_acpi); + +static void piix4_io_quirk(struct pci_dev *dev, const char *name, unsigned int port, unsigned int enable) +{ + u32 devres; + u32 mask, size, base; + + pci_read_config_dword(dev, port, &devres); + if ((devres & enable) != enable) + return; + mask = (devres >> 16) & 15; + base = devres & 0xffff; + size = 16; + for (;;) { + unsigned int bit = size >> 1; + if ((bit & mask) == bit) + break; + size = bit; + } + /* + * For now we only print it out. Eventually we'll want to + * reserve it (at least if it's in the 0x1000+ range), but + * let's get enough confirmation reports first. + */ + base &= -size; + pci_info(dev, "%s PIO at %04x-%04x\n", name, base, base + size - 1); +} + +static void piix4_mem_quirk(struct pci_dev *dev, const char *name, unsigned int port, unsigned int enable) +{ + u32 devres; + u32 mask, size, base; + + pci_read_config_dword(dev, port, &devres); + if ((devres & enable) != enable) + return; + base = devres & 0xffff0000; + mask = (devres & 0x3f) << 16; + size = 128 << 16; + for (;;) { + unsigned int bit = size >> 1; + if ((bit & mask) == bit) + break; + size = bit; + } + + /* + * For now we only print it out. Eventually we'll want to + * reserve it, but let's get enough confirmation reports first. + */ + base &= -size; + pci_info(dev, "%s MMIO at %04x-%04x\n", name, base, base + size - 1); +} + +/* + * PIIX4 ACPI: Two IO regions pointed to by longwords at + * 0x40 (64 bytes of ACPI registers) + * 0x90 (16 bytes of SMB registers) + * and a few strange programmable PIIX4 device resources. + */ +static void quirk_piix4_acpi(struct pci_dev *dev) +{ + u32 res_a; + + quirk_io_region(dev, 0x40, 64, PCI_BRIDGE_RESOURCES, "PIIX4 ACPI"); + quirk_io_region(dev, 0x90, 16, PCI_BRIDGE_RESOURCES+1, "PIIX4 SMB"); + + /* Device resource A has enables for some of the other ones */ + pci_read_config_dword(dev, 0x5c, &res_a); + + piix4_io_quirk(dev, "PIIX4 devres B", 0x60, 3 << 21); + piix4_io_quirk(dev, "PIIX4 devres C", 0x64, 3 << 21); + + /* Device resource D is just bitfields for static resources */ + + /* Device 12 enabled? */ + if (res_a & (1 << 29)) { + piix4_io_quirk(dev, "PIIX4 devres E", 0x68, 1 << 20); + piix4_mem_quirk(dev, "PIIX4 devres F", 0x6c, 1 << 7); + } + /* Device 13 enabled? */ + if (res_a & (1 << 30)) { + piix4_io_quirk(dev, "PIIX4 devres G", 0x70, 1 << 20); + piix4_mem_quirk(dev, "PIIX4 devres H", 0x74, 1 << 7); + } + piix4_io_quirk(dev, "PIIX4 devres I", 0x78, 1 << 20); + piix4_io_quirk(dev, "PIIX4 devres J", 0x7c, 1 << 20); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_3, quirk_piix4_acpi); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443MX_3, quirk_piix4_acpi); + +#define ICH_PMBASE 0x40 +#define ICH_ACPI_CNTL 0x44 +#define ICH4_ACPI_EN 0x10 +#define ICH6_ACPI_EN 0x80 +#define ICH4_GPIOBASE 0x58 +#define ICH4_GPIO_CNTL 0x5c +#define ICH4_GPIO_EN 0x10 +#define ICH6_GPIOBASE 0x48 +#define ICH6_GPIO_CNTL 0x4c +#define ICH6_GPIO_EN 0x10 + +/* + * ICH4, ICH4-M, ICH5, ICH5-M ACPI: Three IO regions pointed to by longwords at + * 0x40 (128 bytes of ACPI, GPIO & TCO registers) + * 0x58 (64 bytes of GPIO I/O space) + */ +static void quirk_ich4_lpc_acpi(struct pci_dev *dev) +{ + u8 enable; + + /* + * The check for PCIBIOS_MIN_IO is to ensure we won't create a conflict + * with low legacy (and fixed) ports. We don't know the decoding + * priority and can't tell whether the legacy device or the one created + * here is really at that address. This happens on boards with broken + * BIOSes. + */ + pci_read_config_byte(dev, ICH_ACPI_CNTL, &enable); + if (enable & ICH4_ACPI_EN) + quirk_io_region(dev, ICH_PMBASE, 128, PCI_BRIDGE_RESOURCES, + "ICH4 ACPI/GPIO/TCO"); + + pci_read_config_byte(dev, ICH4_GPIO_CNTL, &enable); + if (enable & ICH4_GPIO_EN) + quirk_io_region(dev, ICH4_GPIOBASE, 64, PCI_BRIDGE_RESOURCES+1, + "ICH4 GPIO"); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, quirk_ich4_lpc_acpi); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AB_0, quirk_ich4_lpc_acpi); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, quirk_ich4_lpc_acpi); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_10, quirk_ich4_lpc_acpi); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, quirk_ich4_lpc_acpi); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, quirk_ich4_lpc_acpi); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, quirk_ich4_lpc_acpi); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, quirk_ich4_lpc_acpi); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, quirk_ich4_lpc_acpi); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_1, quirk_ich4_lpc_acpi); + +static void ich6_lpc_acpi_gpio(struct pci_dev *dev) +{ + u8 enable; + + pci_read_config_byte(dev, ICH_ACPI_CNTL, &enable); + if (enable & ICH6_ACPI_EN) + quirk_io_region(dev, ICH_PMBASE, 128, PCI_BRIDGE_RESOURCES, + "ICH6 ACPI/GPIO/TCO"); + + pci_read_config_byte(dev, ICH6_GPIO_CNTL, &enable); + if (enable & ICH6_GPIO_EN) + quirk_io_region(dev, ICH6_GPIOBASE, 64, PCI_BRIDGE_RESOURCES+1, + "ICH6 GPIO"); +} + +static void ich6_lpc_generic_decode(struct pci_dev *dev, unsigned int reg, + const char *name, int dynsize) +{ + u32 val; + u32 size, base; + + pci_read_config_dword(dev, reg, &val); + + /* Enabled? */ + if (!(val & 1)) + return; + base = val & 0xfffc; + if (dynsize) { + /* + * This is not correct. It is 16, 32 or 64 bytes depending on + * register D31:F0:ADh bits 5:4. + * + * But this gets us at least _part_ of it. + */ + size = 16; + } else { + size = 128; + } + base &= ~(size-1); + + /* + * Just print it out for now. We should reserve it after more + * debugging. + */ + pci_info(dev, "%s PIO at %04x-%04x\n", name, base, base+size-1); +} + +static void quirk_ich6_lpc(struct pci_dev *dev) +{ + /* Shared ACPI/GPIO decode with all ICH6+ */ + ich6_lpc_acpi_gpio(dev); + + /* ICH6-specific generic IO decode */ + ich6_lpc_generic_decode(dev, 0x84, "LPC Generic IO decode 1", 0); + ich6_lpc_generic_decode(dev, 0x88, "LPC Generic IO decode 2", 1); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_0, quirk_ich6_lpc); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, quirk_ich6_lpc); + +static void ich7_lpc_generic_decode(struct pci_dev *dev, unsigned int reg, + const char *name) +{ + u32 val; + u32 mask, base; + + pci_read_config_dword(dev, reg, &val); + + /* Enabled? */ + if (!(val & 1)) + return; + + /* IO base in bits 15:2, mask in bits 23:18, both are dword-based */ + base = val & 0xfffc; + mask = (val >> 16) & 0xfc; + mask |= 3; + + /* + * Just print it out for now. We should reserve it after more + * debugging. + */ + pci_info(dev, "%s PIO at %04x (mask %04x)\n", name, base, mask); +} + +/* ICH7-10 has the same common LPC generic IO decode registers */ +static void quirk_ich7_lpc(struct pci_dev *dev) +{ + /* We share the common ACPI/GPIO decode with ICH6 */ + ich6_lpc_acpi_gpio(dev); + + /* And have 4 ICH7+ generic decodes */ + ich7_lpc_generic_decode(dev, 0x84, "ICH7 LPC Generic IO decode 1"); + ich7_lpc_generic_decode(dev, 0x88, "ICH7 LPC Generic IO decode 2"); + ich7_lpc_generic_decode(dev, 0x8c, "ICH7 LPC Generic IO decode 3"); + ich7_lpc_generic_decode(dev, 0x90, "ICH7 LPC Generic IO decode 4"); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_0, quirk_ich7_lpc); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_1, quirk_ich7_lpc); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_31, quirk_ich7_lpc); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_0, quirk_ich7_lpc); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_2, quirk_ich7_lpc); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_3, quirk_ich7_lpc); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_1, quirk_ich7_lpc); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_4, quirk_ich7_lpc); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_2, quirk_ich7_lpc); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_4, quirk_ich7_lpc); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_7, quirk_ich7_lpc); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_8, quirk_ich7_lpc); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH10_1, quirk_ich7_lpc); + +/* + * VIA ACPI: One IO region pointed to by longword at + * 0x48 or 0x20 (256 bytes of ACPI registers) + */ +static void quirk_vt82c586_acpi(struct pci_dev *dev) +{ + if (dev->revision & 0x10) + quirk_io_region(dev, 0x48, 256, PCI_BRIDGE_RESOURCES, + "vt82c586 ACPI"); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_vt82c586_acpi); + +/* + * VIA VT82C686 ACPI: Three IO region pointed to by (long)words at + * 0x48 (256 bytes of ACPI registers) + * 0x70 (128 bytes of hardware monitoring register) + * 0x90 (16 bytes of SMB registers) + */ +static void quirk_vt82c686_acpi(struct pci_dev *dev) +{ + quirk_vt82c586_acpi(dev); + + quirk_io_region(dev, 0x70, 128, PCI_BRIDGE_RESOURCES+1, + "vt82c686 HW-mon"); + + quirk_io_region(dev, 0x90, 16, PCI_BRIDGE_RESOURCES+2, "vt82c686 SMB"); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_vt82c686_acpi); + +/* + * VIA VT8235 ISA Bridge: Two IO regions pointed to by words at + * 0x88 (128 bytes of power management registers) + * 0xd0 (16 bytes of SMB registers) + */ +static void quirk_vt8235_acpi(struct pci_dev *dev) +{ + quirk_io_region(dev, 0x88, 128, PCI_BRIDGE_RESOURCES, "vt8235 PM"); + quirk_io_region(dev, 0xd0, 16, PCI_BRIDGE_RESOURCES+1, "vt8235 SMB"); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235, quirk_vt8235_acpi); + +/* + * TI XIO2000a PCIe-PCI Bridge erroneously reports it supports fast + * back-to-back: Disable fast back-to-back on the secondary bus segment + */ +static void quirk_xio2000a(struct pci_dev *dev) +{ + struct pci_dev *pdev; + u16 command; + + pci_warn(dev, "TI XIO2000a quirk detected; secondary bus fast back-to-back transfers disabled\n"); + list_for_each_entry(pdev, &dev->subordinate->devices, bus_list) { + pci_read_config_word(pdev, PCI_COMMAND, &command); + if (command & PCI_COMMAND_FAST_BACK) + pci_write_config_word(pdev, PCI_COMMAND, command & ~PCI_COMMAND_FAST_BACK); + } +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_XIO2000A, + quirk_xio2000a); + +#ifdef CONFIG_X86_IO_APIC + +#include + +/* + * VIA 686A/B: If an IO-APIC is active, we need to route all on-chip + * devices to the external APIC. + * + * TODO: When we have device-specific interrupt routers, this code will go + * away from quirks. + */ +static void quirk_via_ioapic(struct pci_dev *dev) +{ + u8 tmp; + + if (nr_ioapics < 1) + tmp = 0; /* nothing routed to external APIC */ + else + tmp = 0x1f; /* all known bits (4-0) routed to external APIC */ + + pci_info(dev, "%s VIA external APIC routing\n", + tmp ? "Enabling" : "Disabling"); + + /* Offset 0x58: External APIC IRQ output control */ + pci_write_config_byte(dev, 0x58, tmp); +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_ioapic); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_ioapic); + +/* + * VIA 8237: Some BIOSes don't set the 'Bypass APIC De-Assert Message' Bit. + * This leads to doubled level interrupt rates. + * Set this bit to get rid of cycle wastage. + * Otherwise uncritical. + */ +static void quirk_via_vt8237_bypass_apic_deassert(struct pci_dev *dev) +{ + u8 misc_control2; +#define BYPASS_APIC_DEASSERT 8 + + pci_read_config_byte(dev, 0x5B, &misc_control2); + if (!(misc_control2 & BYPASS_APIC_DEASSERT)) { + pci_info(dev, "Bypassing VIA 8237 APIC De-Assert Message\n"); + pci_write_config_byte(dev, 0x5B, misc_control2|BYPASS_APIC_DEASSERT); + } +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, quirk_via_vt8237_bypass_apic_deassert); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, quirk_via_vt8237_bypass_apic_deassert); + +/* + * The AMD IO-APIC can hang the box when an APIC IRQ is masked. + * We check all revs >= B0 (yet not in the pre production!) as the bug + * is currently marked NoFix + * + * We have multiple reports of hangs with this chipset that went away with + * noapic specified. For the moment we assume it's the erratum. We may be wrong + * of course. However the advice is demonstrably good even if so. + */ +static void quirk_amd_ioapic(struct pci_dev *dev) +{ + if (dev->revision >= 0x02) { + pci_warn(dev, "I/O APIC: AMD Erratum #22 may be present. In the event of instability try\n"); + pci_warn(dev, " : booting with the \"noapic\" option\n"); + } +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7410, quirk_amd_ioapic); +#endif /* CONFIG_X86_IO_APIC */ + +#if defined(CONFIG_ARM64) && defined(CONFIG_PCI_ATS) + +static void quirk_cavium_sriov_rnm_link(struct pci_dev *dev) +{ + /* Fix for improper SR-IOV configuration on Cavium cn88xx RNM device */ + if (dev->subsystem_device == 0xa118) + dev->sriov->link = dev->devfn; +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CAVIUM, 0xa018, quirk_cavium_sriov_rnm_link); +#endif + +/* + * Some settings of MMRBC can lead to data corruption so block changes. + * See AMD 8131 HyperTransport PCI-X Tunnel Revision Guide + */ +static void quirk_amd_8131_mmrbc(struct pci_dev *dev) +{ + if (dev->subordinate && dev->revision <= 0x12) { + pci_info(dev, "AMD8131 rev %x detected; disabling PCI-X MMRBC\n", + dev->revision); + dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MMRBC; + } +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_amd_8131_mmrbc); + +/* + * FIXME: it is questionable that quirk_via_acpi() is needed. It shows up + * as an ISA bridge, and does not support the PCI_INTERRUPT_LINE register + * at all. Therefore it seems like setting the pci_dev's IRQ to the value + * of the ACPI SCI interrupt is only done for convenience. + * -jgarzik + */ +static void quirk_via_acpi(struct pci_dev *d) +{ + u8 irq; + + /* VIA ACPI device: SCI IRQ line in PCI config byte 0x42 */ + pci_read_config_byte(d, 0x42, &irq); + irq &= 0xf; + if (irq && (irq != 2)) + d->irq = irq; +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_via_acpi); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_via_acpi); + +/* VIA bridges which have VLink */ +static int via_vlink_dev_lo = -1, via_vlink_dev_hi = 18; + +static void quirk_via_bridge(struct pci_dev *dev) +{ + /* See what bridge we have and find the device ranges */ + switch (dev->device) { + case PCI_DEVICE_ID_VIA_82C686: + /* + * The VT82C686 is special; it attaches to PCI and can have + * any device number. All its subdevices are functions of + * that single device. + */ + via_vlink_dev_lo = PCI_SLOT(dev->devfn); + via_vlink_dev_hi = PCI_SLOT(dev->devfn); + break; + case PCI_DEVICE_ID_VIA_8237: + case PCI_DEVICE_ID_VIA_8237A: + via_vlink_dev_lo = 15; + break; + case PCI_DEVICE_ID_VIA_8235: + via_vlink_dev_lo = 16; + break; + case PCI_DEVICE_ID_VIA_8231: + case PCI_DEVICE_ID_VIA_8233_0: + case PCI_DEVICE_ID_VIA_8233A: + case PCI_DEVICE_ID_VIA_8233C_0: + via_vlink_dev_lo = 17; + break; + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_bridge); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, quirk_via_bridge); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233_0, quirk_via_bridge); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233A, quirk_via_bridge); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233C_0, quirk_via_bridge); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235, quirk_via_bridge); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, quirk_via_bridge); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237A, quirk_via_bridge); + +/* + * quirk_via_vlink - VIA VLink IRQ number update + * @dev: PCI device + * + * If the device we are dealing with is on a PIC IRQ we need to ensure that + * the IRQ line register which usually is not relevant for PCI cards, is + * actually written so that interrupts get sent to the right place. + * + * We only do this on systems where a VIA south bridge was detected, and + * only for VIA devices on the motherboard (see quirk_via_bridge above). + */ +static void quirk_via_vlink(struct pci_dev *dev) +{ + u8 irq, new_irq; + + /* Check if we have VLink at all */ + if (via_vlink_dev_lo == -1) + return; + + new_irq = dev->irq; + + /* Don't quirk interrupts outside the legacy IRQ range */ + if (!new_irq || new_irq > 15) + return; + + /* Internal device ? */ + if (dev->bus->number != 0 || PCI_SLOT(dev->devfn) > via_vlink_dev_hi || + PCI_SLOT(dev->devfn) < via_vlink_dev_lo) + return; + + /* + * This is an internal VLink device on a PIC interrupt. The BIOS + * ought to have set this but may not have, so we redo it. + */ + pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq); + if (new_irq != irq) { + pci_info(dev, "VIA VLink IRQ fixup, from %d to %d\n", + irq, new_irq); + udelay(15); /* unknown if delay really needed */ + pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq); + } +} +DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_vlink); + +/* + * VIA VT82C598 has its device ID settable and many BIOSes set it to the ID + * of VT82C597 for backward compatibility. We need to switch it off to be + * able to recognize the real type of the chip. + */ +static void quirk_vt82c598_id(struct pci_dev *dev) +{ + pci_write_config_byte(dev, 0xfc, 0); + pci_read_config_word(dev, PCI_DEVICE_ID, &dev->device); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C597_0, quirk_vt82c598_id); + +/* + * CardBus controllers have a legacy base address that enables them to + * respond as i82365 pcmcia controllers. We don't want them to do this + * even if the Linux CardBus driver is not loaded, because the Linux i82365 + * driver does not (and should not) handle CardBus. + */ +static void quirk_cardbus_legacy(struct pci_dev *dev) +{ + pci_write_config_dword(dev, PCI_CB_LEGACY_MODE_BASE, 0); +} +DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_ANY_ID, PCI_ANY_ID, + PCI_CLASS_BRIDGE_CARDBUS, 8, quirk_cardbus_legacy); +DECLARE_PCI_FIXUP_CLASS_RESUME_EARLY(PCI_ANY_ID, PCI_ANY_ID, + PCI_CLASS_BRIDGE_CARDBUS, 8, quirk_cardbus_legacy); + +/* + * Following the PCI ordering rules is optional on the AMD762. I'm not sure + * what the designers were smoking but let's not inhale... + * + * To be fair to AMD, it follows the spec by default, it's BIOS people who + * turn it off! + */ +static void quirk_amd_ordering(struct pci_dev *dev) +{ + u32 pcic; + pci_read_config_dword(dev, 0x4C, &pcic); + if ((pcic & 6) != 6) { + pcic |= 6; + pci_warn(dev, "BIOS failed to enable PCI standards compliance; fixing this error\n"); + pci_write_config_dword(dev, 0x4C, pcic); + pci_read_config_dword(dev, 0x84, &pcic); + pcic |= (1 << 23); /* Required in this mode */ + pci_write_config_dword(dev, 0x84, pcic); + } +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_FE_GATE_700C, quirk_amd_ordering); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_FE_GATE_700C, quirk_amd_ordering); + +/* + * DreamWorks-provided workaround for Dunord I-3000 problem + * + * This card decodes and responds to addresses not apparently assigned to + * it. We force a larger allocation to ensure that nothing gets put too + * close to it. + */ +static void quirk_dunord(struct pci_dev *dev) +{ + struct resource *r = &dev->resource[1]; + + r->flags |= IORESOURCE_UNSET; + r->start = 0; + r->end = 0xffffff; +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_DUNORD, PCI_DEVICE_ID_DUNORD_I3000, quirk_dunord); + +/* + * i82380FB mobile docking controller: its PCI-to-PCI bridge is subtractive + * decoding (transparent), and does indicate this in the ProgIf. + * Unfortunately, the ProgIf value is wrong - 0x80 instead of 0x01. + */ +static void quirk_transparent_bridge(struct pci_dev *dev) +{ + dev->transparent = 1; +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82380FB, quirk_transparent_bridge); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TOSHIBA, 0x605, quirk_transparent_bridge); + +/* + * Common misconfiguration of the MediaGX/Geode PCI master that will reduce + * PCI bandwidth from 70MB/s to 25MB/s. See the GXM/GXLV/GX1 datasheets + * found at http://www.national.com/analog for info on what these bits do. + * + */ +static void quirk_mediagx_master(struct pci_dev *dev) +{ + u8 reg; + + pci_read_config_byte(dev, 0x41, ®); + if (reg & 2) { + reg &= ~2; + pci_info(dev, "Fixup for MediaGX/Geode Slave Disconnect Boundary (0x41=0x%02x)\n", + reg); + pci_write_config_byte(dev, 0x41, reg); + } +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_PCI_MASTER, quirk_mediagx_master); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_PCI_MASTER, quirk_mediagx_master); + +/* + * Ensure C0 rev restreaming is off. This is normally done by the BIOS but + * in the odd case it is not the results are corruption hence the presence + * of a Linux check. + */ +static void quirk_disable_pxb(struct pci_dev *pdev) +{ + u16 config; + + if (pdev->revision != 0x04) /* Only C0 requires this */ + return; + pci_read_config_word(pdev, 0x40, &config); + if (config & (1<<6)) { + config &= ~(1<<6); + pci_write_config_word(pdev, 0x40, config); + pci_info(pdev, "C0 revision 450NX. Disabling PCI restreaming\n"); + } +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, quirk_disable_pxb); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, quirk_disable_pxb); + +static void quirk_amd_ide_mode(struct pci_dev *pdev) +{ + /* set SBX00/Hudson-2 SATA in IDE mode to AHCI mode */ + u8 tmp; + + pci_read_config_byte(pdev, PCI_CLASS_DEVICE, &tmp); + if (tmp == 0x01) { + pci_read_config_byte(pdev, 0x40, &tmp); + pci_write_config_byte(pdev, 0x40, tmp|1); + pci_write_config_byte(pdev, 0x9, 1); + pci_write_config_byte(pdev, 0xa, 6); + pci_write_config_byte(pdev, 0x40, tmp); + + pdev->class = PCI_CLASS_STORAGE_SATA_AHCI; + pci_info(pdev, "set SATA to AHCI mode\n"); + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_SATA, quirk_amd_ide_mode); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_SATA, quirk_amd_ide_mode); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP700_SATA, quirk_amd_ide_mode); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP700_SATA, quirk_amd_ide_mode); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_HUDSON2_SATA_IDE, quirk_amd_ide_mode); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_HUDSON2_SATA_IDE, quirk_amd_ide_mode); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x7900, quirk_amd_ide_mode); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AMD, 0x7900, quirk_amd_ide_mode); + +/* Serverworks CSB5 IDE does not fully support native mode */ +static void quirk_svwks_csb5ide(struct pci_dev *pdev) +{ + u8 prog; + pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog); + if (prog & 5) { + prog &= ~5; + pdev->class &= ~5; + pci_write_config_byte(pdev, PCI_CLASS_PROG, prog); + /* PCI layer will sort out resources */ + } +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, quirk_svwks_csb5ide); + +/* Intel 82801CAM ICH3-M datasheet says IDE modes must be the same */ +static void quirk_ide_samemode(struct pci_dev *pdev) +{ + u8 prog; + + pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog); + + if (((prog & 1) && !(prog & 4)) || ((prog & 4) && !(prog & 1))) { + pci_info(pdev, "IDE mode mismatch; forcing legacy mode\n"); + prog &= ~5; + pdev->class &= ~5; + pci_write_config_byte(pdev, PCI_CLASS_PROG, prog); + } +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10, quirk_ide_samemode); + +/* Some ATA devices break if put into D3 */ +static void quirk_no_ata_d3(struct pci_dev *pdev) +{ + pdev->dev_flags |= PCI_DEV_FLAGS_NO_D3; +} +/* Quirk the legacy ATA devices only. The AHCI ones are ok */ +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_SERVERWORKS, PCI_ANY_ID, + PCI_CLASS_STORAGE_IDE, 8, quirk_no_ata_d3); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_ATI, PCI_ANY_ID, + PCI_CLASS_STORAGE_IDE, 8, quirk_no_ata_d3); +/* ALi loses some register settings that we cannot then restore */ +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_AL, PCI_ANY_ID, + PCI_CLASS_STORAGE_IDE, 8, quirk_no_ata_d3); +/* VIA comes back fine but we need to keep it alive or ACPI GTM failures + occur when mode detecting */ +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_VIA, PCI_ANY_ID, + PCI_CLASS_STORAGE_IDE, 8, quirk_no_ata_d3); + +/* + * This was originally an Alpha-specific thing, but it really fits here. + * The i82375 PCI/EISA bridge appears as non-classified. Fix that. + */ +static void quirk_eisa_bridge(struct pci_dev *dev) +{ + dev->class = PCI_CLASS_BRIDGE_EISA << 8; +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82375, quirk_eisa_bridge); + +/* + * On ASUS P4B boards, the SMBus PCI Device within the ICH2/4 southbridge + * is not activated. The myth is that Asus said that they do not want the + * users to be irritated by just another PCI Device in the Win98 device + * manager. (see the file prog/hotplug/README.p4b in the lm_sensors + * package 2.7.0 for details) + * + * The SMBus PCI Device can be activated by setting a bit in the ICH LPC + * bridge. Unfortunately, this device has no subvendor/subdevice ID. So it + * becomes necessary to do this tweak in two steps -- the chosen trigger + * is either the Host bridge (preferred) or on-board VGA controller. + * + * Note that we used to unhide the SMBus that way on Toshiba laptops + * (Satellite A40 and Tecra M2) but then found that the thermal management + * was done by SMM code, which could cause unsynchronized concurrent + * accesses to the SMBus registers, with potentially bad effects. Thus you + * should be very careful when adding new entries: if SMM is accessing the + * Intel SMBus, this is a very good reason to leave it hidden. + * + * Likewise, many recent laptops use ACPI for thermal management. If the + * ACPI DSDT code accesses the SMBus, then Linux should not access it + * natively, and keeping the SMBus hidden is the right thing to do. If you + * are about to add an entry in the table below, please first disassemble + * the DSDT and double-check that there is no code accessing the SMBus. + */ +static int asus_hides_smbus; + +static void asus_hides_smbus_hostbridge(struct pci_dev *dev) +{ + if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK)) { + if (dev->device == PCI_DEVICE_ID_INTEL_82845_HB) + switch (dev->subsystem_device) { + case 0x8025: /* P4B-LX */ + case 0x8070: /* P4B */ + case 0x8088: /* P4B533 */ + case 0x1626: /* L3C notebook */ + asus_hides_smbus = 1; + } + else if (dev->device == PCI_DEVICE_ID_INTEL_82845G_HB) + switch (dev->subsystem_device) { + case 0x80b1: /* P4GE-V */ + case 0x80b2: /* P4PE */ + case 0x8093: /* P4B533-V */ + asus_hides_smbus = 1; + } + else if (dev->device == PCI_DEVICE_ID_INTEL_82850_HB) + switch (dev->subsystem_device) { + case 0x8030: /* P4T533 */ + asus_hides_smbus = 1; + } + else if (dev->device == PCI_DEVICE_ID_INTEL_7205_0) + switch (dev->subsystem_device) { + case 0x8070: /* P4G8X Deluxe */ + asus_hides_smbus = 1; + } + else if (dev->device == PCI_DEVICE_ID_INTEL_E7501_MCH) + switch (dev->subsystem_device) { + case 0x80c9: /* PU-DLS */ + asus_hides_smbus = 1; + } + else if (dev->device == PCI_DEVICE_ID_INTEL_82855GM_HB) + switch (dev->subsystem_device) { + case 0x1751: /* M2N notebook */ + case 0x1821: /* M5N notebook */ + case 0x1897: /* A6L notebook */ + asus_hides_smbus = 1; + } + else if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) + switch (dev->subsystem_device) { + case 0x184b: /* W1N notebook */ + case 0x186a: /* M6Ne notebook */ + asus_hides_smbus = 1; + } + else if (dev->device == PCI_DEVICE_ID_INTEL_82865_HB) + switch (dev->subsystem_device) { + case 0x80f2: /* P4P800-X */ + asus_hides_smbus = 1; + } + else if (dev->device == PCI_DEVICE_ID_INTEL_82915GM_HB) + switch (dev->subsystem_device) { + case 0x1882: /* M6V notebook */ + case 0x1977: /* A6VA notebook */ + asus_hides_smbus = 1; + } + } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_HP)) { + if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) + switch (dev->subsystem_device) { + case 0x088C: /* HP Compaq nc8000 */ + case 0x0890: /* HP Compaq nc6000 */ + asus_hides_smbus = 1; + } + else if (dev->device == PCI_DEVICE_ID_INTEL_82865_HB) + switch (dev->subsystem_device) { + case 0x12bc: /* HP D330L */ + case 0x12bd: /* HP D530 */ + case 0x006a: /* HP Compaq nx9500 */ + asus_hides_smbus = 1; + } + else if (dev->device == PCI_DEVICE_ID_INTEL_82875_HB) + switch (dev->subsystem_device) { + case 0x12bf: /* HP xw4100 */ + asus_hides_smbus = 1; + } + } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_SAMSUNG)) { + if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) + switch (dev->subsystem_device) { + case 0xC00C: /* Samsung P35 notebook */ + asus_hides_smbus = 1; + } + } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_COMPAQ)) { + if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) + switch (dev->subsystem_device) { + case 0x0058: /* Compaq Evo N620c */ + asus_hides_smbus = 1; + } + else if (dev->device == PCI_DEVICE_ID_INTEL_82810_IG3) + switch (dev->subsystem_device) { + case 0xB16C: /* Compaq Deskpro EP 401963-001 (PCA# 010174) */ + /* Motherboard doesn't have Host bridge + * subvendor/subdevice IDs, therefore checking + * its on-board VGA controller */ + asus_hides_smbus = 1; + } + else if (dev->device == PCI_DEVICE_ID_INTEL_82801DB_2) + switch (dev->subsystem_device) { + case 0x00b8: /* Compaq Evo D510 CMT */ + case 0x00b9: /* Compaq Evo D510 SFF */ + case 0x00ba: /* Compaq Evo D510 USDT */ + /* Motherboard doesn't have Host bridge + * subvendor/subdevice IDs and on-board VGA + * controller is disabled if an AGP card is + * inserted, therefore checking USB UHCI + * Controller #1 */ + asus_hides_smbus = 1; + } + else if (dev->device == PCI_DEVICE_ID_INTEL_82815_CGC) + switch (dev->subsystem_device) { + case 0x001A: /* Compaq Deskpro EN SSF P667 815E */ + /* Motherboard doesn't have host bridge + * subvendor/subdevice IDs, therefore checking + * its on-board VGA controller */ + asus_hides_smbus = 1; + } + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845_HB, asus_hides_smbus_hostbridge); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845G_HB, asus_hides_smbus_hostbridge); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82850_HB, asus_hides_smbus_hostbridge); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82865_HB, asus_hides_smbus_hostbridge); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82875_HB, asus_hides_smbus_hostbridge); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_7205_0, asus_hides_smbus_hostbridge); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7501_MCH, asus_hides_smbus_hostbridge); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82855PM_HB, asus_hides_smbus_hostbridge); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82855GM_HB, asus_hides_smbus_hostbridge); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82915GM_HB, asus_hides_smbus_hostbridge); + +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82810_IG3, asus_hides_smbus_hostbridge); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_2, asus_hides_smbus_hostbridge); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82815_CGC, asus_hides_smbus_hostbridge); + +static void asus_hides_smbus_lpc(struct pci_dev *dev) +{ + u16 val; + + if (likely(!asus_hides_smbus)) + return; + + pci_read_config_word(dev, 0xF2, &val); + if (val & 0x8) { + pci_write_config_word(dev, 0xF2, val & (~0x8)); + pci_read_config_word(dev, 0xF2, &val); + if (val & 0x8) + pci_info(dev, "i801 SMBus device continues to play 'hide and seek'! 0x%x\n", + val); + else + pci_info(dev, "Enabled i801 SMBus device\n"); + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, asus_hides_smbus_lpc); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, asus_hides_smbus_lpc); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, asus_hides_smbus_lpc); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, asus_hides_smbus_lpc); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, asus_hides_smbus_lpc); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, asus_hides_smbus_lpc); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, asus_hides_smbus_lpc); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, asus_hides_smbus_lpc); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, asus_hides_smbus_lpc); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, asus_hides_smbus_lpc); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, asus_hides_smbus_lpc); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, asus_hides_smbus_lpc); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, asus_hides_smbus_lpc); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, asus_hides_smbus_lpc); + +/* It appears we just have one such device. If not, we have a warning */ +static void __iomem *asus_rcba_base; +static void asus_hides_smbus_lpc_ich6_suspend(struct pci_dev *dev) +{ + u32 rcba; + + if (likely(!asus_hides_smbus)) + return; + WARN_ON(asus_rcba_base); + + pci_read_config_dword(dev, 0xF0, &rcba); + /* use bits 31:14, 16 kB aligned */ + asus_rcba_base = ioremap(rcba & 0xFFFFC000, 0x4000); + if (asus_rcba_base == NULL) + return; +} + +static void asus_hides_smbus_lpc_ich6_resume_early(struct pci_dev *dev) +{ + u32 val; + + if (likely(!asus_hides_smbus || !asus_rcba_base)) + return; + + /* read the Function Disable register, dword mode only */ + val = readl(asus_rcba_base + 0x3418); + + /* enable the SMBus device */ + writel(val & 0xFFFFFFF7, asus_rcba_base + 0x3418); +} + +static void asus_hides_smbus_lpc_ich6_resume(struct pci_dev *dev) +{ + if (likely(!asus_hides_smbus || !asus_rcba_base)) + return; + + iounmap(asus_rcba_base); + asus_rcba_base = NULL; + pci_info(dev, "Enabled ICH6/i801 SMBus device\n"); +} + +static void asus_hides_smbus_lpc_ich6(struct pci_dev *dev) +{ + asus_hides_smbus_lpc_ich6_suspend(dev); + asus_hides_smbus_lpc_ich6_resume_early(dev); + asus_hides_smbus_lpc_ich6_resume(dev); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6); +DECLARE_PCI_FIXUP_SUSPEND(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6_suspend); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6_resume); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6_resume_early); + +/* SiS 96x south bridge: BIOS typically hides SMBus device... */ +static void quirk_sis_96x_smbus(struct pci_dev *dev) +{ + u8 val = 0; + pci_read_config_byte(dev, 0x77, &val); + if (val & 0x10) { + pci_info(dev, "Enabling SiS 96x SMBus\n"); + pci_write_config_byte(dev, 0x77, val & ~0x10); + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_961, quirk_sis_96x_smbus); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_962, quirk_sis_96x_smbus); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_963, quirk_sis_96x_smbus); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_LPC, quirk_sis_96x_smbus); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_961, quirk_sis_96x_smbus); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_962, quirk_sis_96x_smbus); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_963, quirk_sis_96x_smbus); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_LPC, quirk_sis_96x_smbus); + +/* + * ... This is further complicated by the fact that some SiS96x south + * bridges pretend to be 85C503/5513 instead. In that case see if we + * spotted a compatible north bridge to make sure. + * (pci_find_device() doesn't work yet) + * + * We can also enable the sis96x bit in the discovery register.. + */ +#define SIS_DETECT_REGISTER 0x40 + +static void quirk_sis_503(struct pci_dev *dev) +{ + u8 reg; + u16 devid; + + pci_read_config_byte(dev, SIS_DETECT_REGISTER, ®); + pci_write_config_byte(dev, SIS_DETECT_REGISTER, reg | (1 << 6)); + pci_read_config_word(dev, PCI_DEVICE_ID, &devid); + if (((devid & 0xfff0) != 0x0960) && (devid != 0x0018)) { + pci_write_config_byte(dev, SIS_DETECT_REGISTER, reg); + return; + } + + /* + * Ok, it now shows up as a 96x. Run the 96x quirk by hand in case + * it has already been processed. (Depends on link order, which is + * apparently not guaranteed) + */ + dev->device = devid; + quirk_sis_96x_smbus(dev); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_503, quirk_sis_503); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_503, quirk_sis_503); + +/* + * On ASUS A8V and A8V Deluxe boards, the onboard AC97 audio controller + * and MC97 modem controller are disabled when a second PCI soundcard is + * present. This patch, tweaking the VT8237 ISA bridge, enables them. + * -- bjd + */ +static void asus_hides_ac97_lpc(struct pci_dev *dev) +{ + u8 val; + int asus_hides_ac97 = 0; + + if (likely(dev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK)) { + if (dev->device == PCI_DEVICE_ID_VIA_8237) + asus_hides_ac97 = 1; + } + + if (!asus_hides_ac97) + return; + + pci_read_config_byte(dev, 0x50, &val); + if (val & 0xc0) { + pci_write_config_byte(dev, 0x50, val & (~0xc0)); + pci_read_config_byte(dev, 0x50, &val); + if (val & 0xc0) + pci_info(dev, "Onboard AC97/MC97 devices continue to play 'hide and seek'! 0x%x\n", + val); + else + pci_info(dev, "Enabled onboard AC97/MC97 devices\n"); + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, asus_hides_ac97_lpc); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, asus_hides_ac97_lpc); + +#if defined(CONFIG_ATA) || defined(CONFIG_ATA_MODULE) + +/* + * If we are using libata we can drive this chip properly but must do this + * early on to make the additional device appear during the PCI scanning. + */ +static void quirk_jmicron_ata(struct pci_dev *pdev) +{ + u32 conf1, conf5, class; + u8 hdr; + + /* Only poke fn 0 */ + if (PCI_FUNC(pdev->devfn)) + return; + + pci_read_config_dword(pdev, 0x40, &conf1); + pci_read_config_dword(pdev, 0x80, &conf5); + + conf1 &= ~0x00CFF302; /* Clear bit 1, 8, 9, 12-19, 22, 23 */ + conf5 &= ~(1 << 24); /* Clear bit 24 */ + + switch (pdev->device) { + case PCI_DEVICE_ID_JMICRON_JMB360: /* SATA single port */ + case PCI_DEVICE_ID_JMICRON_JMB362: /* SATA dual ports */ + case PCI_DEVICE_ID_JMICRON_JMB364: /* SATA dual ports */ + /* The controller should be in single function ahci mode */ + conf1 |= 0x0002A100; /* Set 8, 13, 15, 17 */ + break; + + case PCI_DEVICE_ID_JMICRON_JMB365: + case PCI_DEVICE_ID_JMICRON_JMB366: + /* Redirect IDE second PATA port to the right spot */ + conf5 |= (1 << 24); + fallthrough; + case PCI_DEVICE_ID_JMICRON_JMB361: + case PCI_DEVICE_ID_JMICRON_JMB363: + case PCI_DEVICE_ID_JMICRON_JMB369: + /* Enable dual function mode, AHCI on fn 0, IDE fn1 */ + /* Set the class codes correctly and then direct IDE 0 */ + conf1 |= 0x00C2A1B3; /* Set 0, 1, 4, 5, 7, 8, 13, 15, 17, 22, 23 */ + break; + + case PCI_DEVICE_ID_JMICRON_JMB368: + /* The controller should be in single function IDE mode */ + conf1 |= 0x00C00000; /* Set 22, 23 */ + break; + } + + pci_write_config_dword(pdev, 0x40, conf1); + pci_write_config_dword(pdev, 0x80, conf5); + + /* Update pdev accordingly */ + pci_read_config_byte(pdev, PCI_HEADER_TYPE, &hdr); + pdev->hdr_type = hdr & 0x7f; + pdev->multifunction = !!(hdr & 0x80); + + pci_read_config_dword(pdev, PCI_CLASS_REVISION, &class); + pdev->class = class >> 8; +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB362, quirk_jmicron_ata); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB364, quirk_jmicron_ata); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB369, quirk_jmicron_ata); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB362, quirk_jmicron_ata); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB364, quirk_jmicron_ata); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB369, quirk_jmicron_ata); + +#endif + +static void quirk_jmicron_async_suspend(struct pci_dev *dev) +{ + if (dev->multifunction) { + device_disable_async_suspend(&dev->dev); + pci_info(dev, "async suspend disabled to avoid multi-function power-on ordering issue\n"); + } +} +DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_CLASS_STORAGE_IDE, 8, quirk_jmicron_async_suspend); +DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_CLASS_STORAGE_SATA_AHCI, 0, quirk_jmicron_async_suspend); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_JMICRON, 0x2362, quirk_jmicron_async_suspend); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_JMICRON, 0x236f, quirk_jmicron_async_suspend); + +#ifdef CONFIG_X86_IO_APIC +static void quirk_alder_ioapic(struct pci_dev *pdev) +{ + int i; + + if ((pdev->class >> 8) != 0xff00) + return; + + /* + * The first BAR is the location of the IO-APIC... we must + * not touch this (and it's already covered by the fixmap), so + * forcibly insert it into the resource tree. + */ + if (pci_resource_start(pdev, 0) && pci_resource_len(pdev, 0)) + insert_resource(&iomem_resource, &pdev->resource[0]); + + /* + * The next five BARs all seem to be rubbish, so just clean + * them out. + */ + for (i = 1; i < PCI_STD_NUM_BARS; i++) + memset(&pdev->resource[i], 0, sizeof(pdev->resource[i])); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EESSC, quirk_alder_ioapic); +#endif + +static void quirk_no_msi(struct pci_dev *dev) +{ + pci_info(dev, "avoiding MSI to work around a hardware defect\n"); + dev->no_msi = 1; +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4386, quirk_no_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4387, quirk_no_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4388, quirk_no_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4389, quirk_no_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x438a, quirk_no_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x438b, quirk_no_msi); + +static void quirk_pcie_mch(struct pci_dev *pdev) +{ + pdev->no_msi = 1; +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7520_MCH, quirk_pcie_mch); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7320_MCH, quirk_pcie_mch); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7525_MCH, quirk_pcie_mch); + +DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_HUAWEI, 0x1610, PCI_CLASS_BRIDGE_PCI, 8, quirk_pcie_mch); + +/* + * HiSilicon KunPeng920 and KunPeng930 have devices appear as PCI but are + * actually on the AMBA bus. These fake PCI devices can support SVA via + * SMMU stall feature, by setting dma-can-stall for ACPI platforms. + * + * Normally stalling must not be enabled for PCI devices, since it would + * break the PCI requirement for free-flowing writes and may lead to + * deadlock. We expect PCI devices to support ATS and PRI if they want to + * be fault-tolerant, so there's no ACPI binding to describe anything else, + * even when a "PCI" device turns out to be a regular old SoC device + * dressed up as a RCiEP and normal rules don't apply. + */ +static void quirk_huawei_pcie_sva(struct pci_dev *pdev) +{ + struct property_entry properties[] = { + PROPERTY_ENTRY_BOOL("dma-can-stall"), + {}, + }; + + if (pdev->revision != 0x21 && pdev->revision != 0x30) + return; + + pdev->pasid_no_tlp = 1; + + /* + * Set the dma-can-stall property on ACPI platforms. Device tree + * can set it directly. + */ + if (!pdev->dev.of_node && + device_create_managed_software_node(&pdev->dev, properties, NULL)) + pci_warn(pdev, "could not add stall property"); +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_HUAWEI, 0xa250, quirk_huawei_pcie_sva); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_HUAWEI, 0xa251, quirk_huawei_pcie_sva); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_HUAWEI, 0xa255, quirk_huawei_pcie_sva); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_HUAWEI, 0xa256, quirk_huawei_pcie_sva); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_HUAWEI, 0xa258, quirk_huawei_pcie_sva); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_HUAWEI, 0xa259, quirk_huawei_pcie_sva); + +/* + * It's possible for the MSI to get corrupted if SHPC and ACPI are used + * together on certain PXH-based systems. + */ +static void quirk_pcie_pxh(struct pci_dev *dev) +{ + dev->no_msi = 1; + pci_warn(dev, "PXH quirk detected; SHPC device MSI disabled\n"); +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHD_0, quirk_pcie_pxh); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHD_1, quirk_pcie_pxh); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_pcie_pxh); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_pcie_pxh); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_pcie_pxh); + +/* + * Some Intel PCI Express chipsets have trouble with downstream device + * power management. + */ +static void quirk_intel_pcie_pm(struct pci_dev *dev) +{ + pci_pm_d3hot_delay = 120; + dev->no_d1d2 = 1; +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e2, quirk_intel_pcie_pm); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e3, quirk_intel_pcie_pm); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e4, quirk_intel_pcie_pm); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e5, quirk_intel_pcie_pm); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e6, quirk_intel_pcie_pm); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e7, quirk_intel_pcie_pm); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25f7, quirk_intel_pcie_pm); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25f8, quirk_intel_pcie_pm); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25f9, quirk_intel_pcie_pm); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25fa, quirk_intel_pcie_pm); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2601, quirk_intel_pcie_pm); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2602, quirk_intel_pcie_pm); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2603, quirk_intel_pcie_pm); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2604, quirk_intel_pcie_pm); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2605, quirk_intel_pcie_pm); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2606, quirk_intel_pcie_pm); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2607, quirk_intel_pcie_pm); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2608, quirk_intel_pcie_pm); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2609, quirk_intel_pcie_pm); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x260a, quirk_intel_pcie_pm); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x260b, quirk_intel_pcie_pm); + +static void quirk_d3hot_delay(struct pci_dev *dev, unsigned int delay) +{ + if (dev->d3hot_delay >= delay) + return; + + dev->d3hot_delay = delay; + pci_info(dev, "extending delay after power-on from D3hot to %d msec\n", + dev->d3hot_delay); +} + +static void quirk_radeon_pm(struct pci_dev *dev) +{ + if (dev->subsystem_vendor == PCI_VENDOR_ID_APPLE && + dev->subsystem_device == 0x00e2) + quirk_d3hot_delay(dev, 20); +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x6741, quirk_radeon_pm); + +/* + * NVIDIA Ampere-based HDA controllers can wedge the whole device if a bus + * reset is performed too soon after transition to D0, extend d3hot_delay + * to previous effective default for all NVIDIA HDA controllers. + */ +static void quirk_nvidia_hda_pm(struct pci_dev *dev) +{ + quirk_d3hot_delay(dev, 20); +} +DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, + PCI_CLASS_MULTIMEDIA_HD_AUDIO, 8, + quirk_nvidia_hda_pm); + +/* + * Ryzen5/7 XHCI controllers fail upon resume from runtime suspend or s2idle. + * https://bugzilla.kernel.org/show_bug.cgi?id=205587 + * + * The kernel attempts to transition these devices to D3cold, but that seems + * to be ineffective on the platforms in question; the PCI device appears to + * remain on in D3hot state. The D3hot-to-D0 transition then requires an + * extended delay in order to succeed. + */ +static void quirk_ryzen_xhci_d3hot(struct pci_dev *dev) +{ + quirk_d3hot_delay(dev, 20); +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x15e0, quirk_ryzen_xhci_d3hot); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x15e1, quirk_ryzen_xhci_d3hot); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x1639, quirk_ryzen_xhci_d3hot); + +#ifdef CONFIG_X86_IO_APIC +static int dmi_disable_ioapicreroute(const struct dmi_system_id *d) +{ + noioapicreroute = 1; + pr_info("%s detected: disable boot interrupt reroute\n", d->ident); + + return 0; +} + +static const struct dmi_system_id boot_interrupt_dmi_table[] = { + /* + * Systems to exclude from boot interrupt reroute quirks + */ + { + .callback = dmi_disable_ioapicreroute, + .ident = "ASUSTek Computer INC. M2N-LR", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "ASUSTek Computer INC."), + DMI_MATCH(DMI_PRODUCT_NAME, "M2N-LR"), + }, + }, + {} +}; + +/* + * Boot interrupts on some chipsets cannot be turned off. For these chipsets, + * remap the original interrupt in the Linux kernel to the boot interrupt, so + * that a PCI device's interrupt handler is installed on the boot interrupt + * line instead. + */ +static void quirk_reroute_to_boot_interrupts_intel(struct pci_dev *dev) +{ + dmi_check_system(boot_interrupt_dmi_table); + if (noioapicquirk || noioapicreroute) + return; + + dev->irq_reroute_variant = INTEL_IRQ_REROUTE_VARIANT; + pci_info(dev, "rerouting interrupts for [%04x:%04x]\n", + dev->vendor, dev->device); +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_0, quirk_reroute_to_boot_interrupts_intel); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_1, quirk_reroute_to_boot_interrupts_intel); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_0, quirk_reroute_to_boot_interrupts_intel); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_reroute_to_boot_interrupts_intel); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_reroute_to_boot_interrupts_intel); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_reroute_to_boot_interrupts_intel); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_0, quirk_reroute_to_boot_interrupts_intel); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_1, quirk_reroute_to_boot_interrupts_intel); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_0, quirk_reroute_to_boot_interrupts_intel); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_1, quirk_reroute_to_boot_interrupts_intel); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_0, quirk_reroute_to_boot_interrupts_intel); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_reroute_to_boot_interrupts_intel); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_reroute_to_boot_interrupts_intel); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_reroute_to_boot_interrupts_intel); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_0, quirk_reroute_to_boot_interrupts_intel); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_1, quirk_reroute_to_boot_interrupts_intel); + +/* + * On some chipsets we can disable the generation of legacy INTx boot + * interrupts. + */ + +/* + * IO-APIC1 on 6300ESB generates boot interrupts, see Intel order no + * 300641-004US, section 5.7.3. + * + * Core IO on Xeon E5 1600/2600/4600, see Intel order no 326509-003. + * Core IO on Xeon E5 v2, see Intel order no 329188-003. + * Core IO on Xeon E7 v2, see Intel order no 329595-002. + * Core IO on Xeon E5 v3, see Intel order no 330784-003. + * Core IO on Xeon E7 v3, see Intel order no 332315-001US. + * Core IO on Xeon E5 v4, see Intel order no 333810-002US. + * Core IO on Xeon E7 v4, see Intel order no 332315-001US. + * Core IO on Xeon D-1500, see Intel order no 332051-001. + * Core IO on Xeon Scalable, see Intel order no 610950. + */ +#define INTEL_6300_IOAPIC_ABAR 0x40 /* Bus 0, Dev 29, Func 5 */ +#define INTEL_6300_DISABLE_BOOT_IRQ (1<<14) + +#define INTEL_CIPINTRC_CFG_OFFSET 0x14C /* Bus 0, Dev 5, Func 0 */ +#define INTEL_CIPINTRC_DIS_INTX_ICH (1<<25) + +static void quirk_disable_intel_boot_interrupt(struct pci_dev *dev) +{ + u16 pci_config_word; + u32 pci_config_dword; + + if (noioapicquirk) + return; + + switch (dev->device) { + case PCI_DEVICE_ID_INTEL_ESB_10: + pci_read_config_word(dev, INTEL_6300_IOAPIC_ABAR, + &pci_config_word); + pci_config_word |= INTEL_6300_DISABLE_BOOT_IRQ; + pci_write_config_word(dev, INTEL_6300_IOAPIC_ABAR, + pci_config_word); + break; + case 0x3c28: /* Xeon E5 1600/2600/4600 */ + case 0x0e28: /* Xeon E5/E7 V2 */ + case 0x2f28: /* Xeon E5/E7 V3,V4 */ + case 0x6f28: /* Xeon D-1500 */ + case 0x2034: /* Xeon Scalable Family */ + pci_read_config_dword(dev, INTEL_CIPINTRC_CFG_OFFSET, + &pci_config_dword); + pci_config_dword |= INTEL_CIPINTRC_DIS_INTX_ICH; + pci_write_config_dword(dev, INTEL_CIPINTRC_CFG_OFFSET, + pci_config_dword); + break; + default: + return; + } + pci_info(dev, "disabled boot interrupts on device [%04x:%04x]\n", + dev->vendor, dev->device); +} +/* + * Device 29 Func 5 Device IDs of IO-APIC + * containing ABAR—APIC1 Alternate Base Address Register + */ +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_10, + quirk_disable_intel_boot_interrupt); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_10, + quirk_disable_intel_boot_interrupt); + +/* + * Device 5 Func 0 Device IDs of Core IO modules/hubs + * containing Coherent Interface Protocol Interrupt Control + * + * Device IDs obtained from volume 2 datasheets of commented + * families above. + */ +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x3c28, + quirk_disable_intel_boot_interrupt); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0e28, + quirk_disable_intel_boot_interrupt); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2f28, + quirk_disable_intel_boot_interrupt); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x6f28, + quirk_disable_intel_boot_interrupt); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2034, + quirk_disable_intel_boot_interrupt); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, 0x3c28, + quirk_disable_intel_boot_interrupt); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, 0x0e28, + quirk_disable_intel_boot_interrupt); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, 0x2f28, + quirk_disable_intel_boot_interrupt); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, 0x6f28, + quirk_disable_intel_boot_interrupt); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, 0x2034, + quirk_disable_intel_boot_interrupt); + +/* Disable boot interrupts on HT-1000 */ +#define BC_HT1000_FEATURE_REG 0x64 +#define BC_HT1000_PIC_REGS_ENABLE (1<<0) +#define BC_HT1000_MAP_IDX 0xC00 +#define BC_HT1000_MAP_DATA 0xC01 + +static void quirk_disable_broadcom_boot_interrupt(struct pci_dev *dev) +{ + u32 pci_config_dword; + u8 irq; + + if (noioapicquirk) + return; + + pci_read_config_dword(dev, BC_HT1000_FEATURE_REG, &pci_config_dword); + pci_write_config_dword(dev, BC_HT1000_FEATURE_REG, pci_config_dword | + BC_HT1000_PIC_REGS_ENABLE); + + for (irq = 0x10; irq < 0x10 + 32; irq++) { + outb(irq, BC_HT1000_MAP_IDX); + outb(0x00, BC_HT1000_MAP_DATA); + } + + pci_write_config_dword(dev, BC_HT1000_FEATURE_REG, pci_config_dword); + + pci_info(dev, "disabled boot interrupts on device [%04x:%04x]\n", + dev->vendor, dev->device); +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000SB, quirk_disable_broadcom_boot_interrupt); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000SB, quirk_disable_broadcom_boot_interrupt); + +/* Disable boot interrupts on AMD and ATI chipsets */ + +/* + * NOIOAMODE needs to be disabled to disable "boot interrupts". For AMD 8131 + * rev. A0 and B0, NOIOAMODE needs to be disabled anyway to fix IO-APIC mode + * (due to an erratum). + */ +#define AMD_813X_MISC 0x40 +#define AMD_813X_NOIOAMODE (1<<0) +#define AMD_813X_REV_B1 0x12 +#define AMD_813X_REV_B2 0x13 + +static void quirk_disable_amd_813x_boot_interrupt(struct pci_dev *dev) +{ + u32 pci_config_dword; + + if (noioapicquirk) + return; + if ((dev->revision == AMD_813X_REV_B1) || + (dev->revision == AMD_813X_REV_B2)) + return; + + pci_read_config_dword(dev, AMD_813X_MISC, &pci_config_dword); + pci_config_dword &= ~AMD_813X_NOIOAMODE; + pci_write_config_dword(dev, AMD_813X_MISC, pci_config_dword); + + pci_info(dev, "disabled boot interrupts on device [%04x:%04x]\n", + dev->vendor, dev->device); +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_amd_813x_boot_interrupt); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_amd_813x_boot_interrupt); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE, quirk_disable_amd_813x_boot_interrupt); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE, quirk_disable_amd_813x_boot_interrupt); + +#define AMD_8111_PCI_IRQ_ROUTING 0x56 + +static void quirk_disable_amd_8111_boot_interrupt(struct pci_dev *dev) +{ + u16 pci_config_word; + + if (noioapicquirk) + return; + + pci_read_config_word(dev, AMD_8111_PCI_IRQ_ROUTING, &pci_config_word); + if (!pci_config_word) { + pci_info(dev, "boot interrupts on device [%04x:%04x] already disabled\n", + dev->vendor, dev->device); + return; + } + pci_write_config_word(dev, AMD_8111_PCI_IRQ_ROUTING, 0); + pci_info(dev, "disabled boot interrupts on device [%04x:%04x]\n", + dev->vendor, dev->device); +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8111_SMBUS, quirk_disable_amd_8111_boot_interrupt); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8111_SMBUS, quirk_disable_amd_8111_boot_interrupt); +#endif /* CONFIG_X86_IO_APIC */ + +/* + * Toshiba TC86C001 IDE controller reports the standard 8-byte BAR0 size + * but the PIO transfers won't work if BAR0 falls at the odd 8 bytes. + * Re-allocate the region if needed... + */ +static void quirk_tc86c001_ide(struct pci_dev *dev) +{ + struct resource *r = &dev->resource[0]; + + if (r->start & 0x8) { + r->flags |= IORESOURCE_UNSET; + r->start = 0; + r->end = 0xf; + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TOSHIBA_2, + PCI_DEVICE_ID_TOSHIBA_TC86C001_IDE, + quirk_tc86c001_ide); + +/* + * PLX PCI 9050 PCI Target bridge controller has an erratum that prevents the + * local configuration registers accessible via BAR0 (memory) or BAR1 (i/o) + * being read correctly if bit 7 of the base address is set. + * The BAR0 or BAR1 region may be disabled (size 0) or enabled (size 128). + * Re-allocate the regions to a 256-byte boundary if necessary. + */ +static void quirk_plx_pci9050(struct pci_dev *dev) +{ + unsigned int bar; + + /* Fixed in revision 2 (PCI 9052). */ + if (dev->revision >= 2) + return; + for (bar = 0; bar <= 1; bar++) + if (pci_resource_len(dev, bar) == 0x80 && + (pci_resource_start(dev, bar) & 0x80)) { + struct resource *r = &dev->resource[bar]; + pci_info(dev, "Re-allocating PLX PCI 9050 BAR %u to length 256 to avoid bit 7 bug\n", + bar); + r->flags |= IORESOURCE_UNSET; + r->start = 0; + r->end = 0xff; + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050, + quirk_plx_pci9050); +/* + * The following Meilhaus (vendor ID 0x1402) device IDs (amongst others) + * may be using the PLX PCI 9050: 0x0630, 0x0940, 0x0950, 0x0960, 0x100b, + * 0x1400, 0x140a, 0x140b, 0x14e0, 0x14ea, 0x14eb, 0x1604, 0x1608, 0x160c, + * 0x168f, 0x2000, 0x2600, 0x3000, 0x810a, 0x810b. + * + * Currently, device IDs 0x2000 and 0x2600 are used by the Comedi "me_daq" + * driver. + */ +DECLARE_PCI_FIXUP_HEADER(0x1402, 0x2000, quirk_plx_pci9050); +DECLARE_PCI_FIXUP_HEADER(0x1402, 0x2600, quirk_plx_pci9050); + +static void quirk_netmos(struct pci_dev *dev) +{ + unsigned int num_parallel = (dev->subsystem_device & 0xf0) >> 4; + unsigned int num_serial = dev->subsystem_device & 0xf; + + /* + * These Netmos parts are multiport serial devices with optional + * parallel ports. Even when parallel ports are present, they + * are identified as class SERIAL, which means the serial driver + * will claim them. To prevent this, mark them as class OTHER. + * These combo devices should be claimed by parport_serial. + * + * The subdevice ID is of the form 0x00PS, where

is the number + * of parallel ports and is the number of serial ports. + */ + switch (dev->device) { + case PCI_DEVICE_ID_NETMOS_9835: + /* Well, this rule doesn't hold for the following 9835 device */ + if (dev->subsystem_vendor == PCI_VENDOR_ID_IBM && + dev->subsystem_device == 0x0299) + return; + fallthrough; + case PCI_DEVICE_ID_NETMOS_9735: + case PCI_DEVICE_ID_NETMOS_9745: + case PCI_DEVICE_ID_NETMOS_9845: + case PCI_DEVICE_ID_NETMOS_9855: + if (num_parallel) { + pci_info(dev, "Netmos %04x (%u parallel, %u serial); changing class SERIAL to OTHER (use parport_serial)\n", + dev->device, num_parallel, num_serial); + dev->class = (PCI_CLASS_COMMUNICATION_OTHER << 8) | + (dev->class & 0xff); + } + } +} +DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_VENDOR_ID_NETMOS, PCI_ANY_ID, + PCI_CLASS_COMMUNICATION_SERIAL, 8, quirk_netmos); + +static void quirk_e100_interrupt(struct pci_dev *dev) +{ + u16 command, pmcsr; + u8 __iomem *csr; + u8 cmd_hi; + + switch (dev->device) { + /* PCI IDs taken from drivers/net/e100.c */ + case 0x1029: + case 0x1030 ... 0x1034: + case 0x1038 ... 0x103E: + case 0x1050 ... 0x1057: + case 0x1059: + case 0x1064 ... 0x106B: + case 0x1091 ... 0x1095: + case 0x1209: + case 0x1229: + case 0x2449: + case 0x2459: + case 0x245D: + case 0x27DC: + break; + default: + return; + } + + /* + * Some firmware hands off the e100 with interrupts enabled, + * which can cause a flood of interrupts if packets are + * received before the driver attaches to the device. So + * disable all e100 interrupts here. The driver will + * re-enable them when it's ready. + */ + pci_read_config_word(dev, PCI_COMMAND, &command); + + if (!(command & PCI_COMMAND_MEMORY) || !pci_resource_start(dev, 0)) + return; + + /* + * Check that the device is in the D0 power state. If it's not, + * there is no point to look any further. + */ + if (dev->pm_cap) { + pci_read_config_word(dev, dev->pm_cap + PCI_PM_CTRL, &pmcsr); + if ((pmcsr & PCI_PM_CTRL_STATE_MASK) != PCI_D0) + return; + } + + /* Convert from PCI bus to resource space. */ + csr = ioremap(pci_resource_start(dev, 0), 8); + if (!csr) { + pci_warn(dev, "Can't map e100 registers\n"); + return; + } + + cmd_hi = readb(csr + 3); + if (cmd_hi == 0) { + pci_warn(dev, "Firmware left e100 interrupts enabled; disabling\n"); + writeb(1, csr + 3); + } + + iounmap(csr); +} +DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, + PCI_CLASS_NETWORK_ETHERNET, 8, quirk_e100_interrupt); + +/* + * The 82575 and 82598 may experience data corruption issues when transitioning + * out of L0S. To prevent this we need to disable L0S on the PCIe link. + */ +static void quirk_disable_aspm_l0s(struct pci_dev *dev) +{ + pci_info(dev, "Disabling L0s\n"); + pci_disable_link_state(dev, PCIE_LINK_STATE_L0S); +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10a7, quirk_disable_aspm_l0s); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10a9, quirk_disable_aspm_l0s); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10b6, quirk_disable_aspm_l0s); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c6, quirk_disable_aspm_l0s); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c7, quirk_disable_aspm_l0s); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c8, quirk_disable_aspm_l0s); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10d6, quirk_disable_aspm_l0s); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10db, quirk_disable_aspm_l0s); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10dd, quirk_disable_aspm_l0s); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10e1, quirk_disable_aspm_l0s); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10ec, quirk_disable_aspm_l0s); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10f1, quirk_disable_aspm_l0s); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10f4, quirk_disable_aspm_l0s); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1508, quirk_disable_aspm_l0s); + +static void quirk_disable_aspm_l0s_l1(struct pci_dev *dev) +{ + pci_info(dev, "Disabling ASPM L0s/L1\n"); + pci_disable_link_state(dev, PCIE_LINK_STATE_L0S | PCIE_LINK_STATE_L1); +} + +/* + * ASM1083/1085 PCIe-PCI bridge devices cause AER timeout errors on the + * upstream PCIe root port when ASPM is enabled. At least L0s mode is affected; + * disable both L0s and L1 for now to be safe. + */ +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ASMEDIA, 0x1080, quirk_disable_aspm_l0s_l1); + +/* + * Some Pericom PCIe-to-PCI bridges in reverse mode need the PCIe Retrain + * Link bit cleared after starting the link retrain process to allow this + * process to finish. + * + * Affected devices: PI7C9X110, PI7C9X111SL, PI7C9X130. See also the + * Pericom Errata Sheet PI7C9X111SLB_errata_rev1.2_102711.pdf. + */ +static void quirk_enable_clear_retrain_link(struct pci_dev *dev) +{ + dev->clear_retrain_link = 1; + pci_info(dev, "Enable PCIe Retrain Link quirk\n"); +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_PERICOM, 0xe110, quirk_enable_clear_retrain_link); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_PERICOM, 0xe111, quirk_enable_clear_retrain_link); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_PERICOM, 0xe130, quirk_enable_clear_retrain_link); + +static void fixup_rev1_53c810(struct pci_dev *dev) +{ + u32 class = dev->class; + + /* + * rev 1 ncr53c810 chips don't set the class at all which means + * they don't get their resources remapped. Fix that here. + */ + if (class) + return; + + dev->class = PCI_CLASS_STORAGE_SCSI << 8; + pci_info(dev, "NCR 53c810 rev 1 PCI class overridden (%#08x -> %#08x)\n", + class, dev->class); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NCR, PCI_DEVICE_ID_NCR_53C810, fixup_rev1_53c810); + +/* Enable 1k I/O space granularity on the Intel P64H2 */ +static void quirk_p64h2_1k_io(struct pci_dev *dev) +{ + u16 en1k; + + pci_read_config_word(dev, 0x40, &en1k); + + if (en1k & 0x200) { + pci_info(dev, "Enable I/O Space to 1KB granularity\n"); + dev->io_window_1k = 1; + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x1460, quirk_p64h2_1k_io); + +/* + * Under some circumstances, AER is not linked with extended capabilities. + * Force it to be linked by setting the corresponding control bit in the + * config space. + */ +static void quirk_nvidia_ck804_pcie_aer_ext_cap(struct pci_dev *dev) +{ + uint8_t b; + + if (pci_read_config_byte(dev, 0xf41, &b) == 0) { + if (!(b & 0x20)) { + pci_write_config_byte(dev, 0xf41, b | 0x20); + pci_info(dev, "Linking AER extended capability\n"); + } + } +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_CK804_PCIE, + quirk_nvidia_ck804_pcie_aer_ext_cap); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_CK804_PCIE, + quirk_nvidia_ck804_pcie_aer_ext_cap); + +static void quirk_via_cx700_pci_parking_caching(struct pci_dev *dev) +{ + /* + * Disable PCI Bus Parking and PCI Master read caching on CX700 + * which causes unspecified timing errors with a VT6212L on the PCI + * bus leading to USB2.0 packet loss. + * + * This quirk is only enabled if a second (on the external PCI bus) + * VT6212L is found -- the CX700 core itself also contains a USB + * host controller with the same PCI ID as the VT6212L. + */ + + /* Count VT6212L instances */ + struct pci_dev *p = pci_get_device(PCI_VENDOR_ID_VIA, + PCI_DEVICE_ID_VIA_8235_USB_2, NULL); + uint8_t b; + + /* + * p should contain the first (internal) VT6212L -- see if we have + * an external one by searching again. + */ + p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235_USB_2, p); + if (!p) + return; + pci_dev_put(p); + + if (pci_read_config_byte(dev, 0x76, &b) == 0) { + if (b & 0x40) { + /* Turn off PCI Bus Parking */ + pci_write_config_byte(dev, 0x76, b ^ 0x40); + + pci_info(dev, "Disabling VIA CX700 PCI parking\n"); + } + } + + if (pci_read_config_byte(dev, 0x72, &b) == 0) { + if (b != 0) { + /* Turn off PCI Master read caching */ + pci_write_config_byte(dev, 0x72, 0x0); + + /* Set PCI Master Bus time-out to "1x16 PCLK" */ + pci_write_config_byte(dev, 0x75, 0x1); + + /* Disable "Read FIFO Timer" */ + pci_write_config_byte(dev, 0x77, 0x0); + + pci_info(dev, "Disabling VIA CX700 PCI caching\n"); + } + } +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, 0x324e, quirk_via_cx700_pci_parking_caching); + +static void quirk_brcm_5719_limit_mrrs(struct pci_dev *dev) +{ + u32 rev; + + pci_read_config_dword(dev, 0xf4, &rev); + + /* Only CAP the MRRS if the device is a 5719 A0 */ + if (rev == 0x05719000) { + int readrq = pcie_get_readrq(dev); + if (readrq > 2048) + pcie_set_readrq(dev, 2048); + } +} +DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_BROADCOM, + PCI_DEVICE_ID_TIGON3_5719, + quirk_brcm_5719_limit_mrrs); + +/* + * Originally in EDAC sources for i82875P: Intel tells BIOS developers to + * hide device 6 which configures the overflow device access containing the + * DRBs - this is where we expose device 6. + * http://www.x86-secret.com/articles/tweak/pat/patsecrets-2.htm + */ +static void quirk_unhide_mch_dev6(struct pci_dev *dev) +{ + u8 reg; + + if (pci_read_config_byte(dev, 0xF4, ®) == 0 && !(reg & 0x02)) { + pci_info(dev, "Enabling MCH 'Overflow' Device\n"); + pci_write_config_byte(dev, 0xF4, reg | 0x02); + } +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82865_HB, + quirk_unhide_mch_dev6); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82875_HB, + quirk_unhide_mch_dev6); + +#ifdef CONFIG_PCI_MSI +/* + * Some chipsets do not support MSI. We cannot easily rely on setting + * PCI_BUS_FLAGS_NO_MSI in its bus flags because there are actually some + * other buses controlled by the chipset even if Linux is not aware of it. + * Instead of setting the flag on all buses in the machine, simply disable + * MSI globally. + */ +static void quirk_disable_all_msi(struct pci_dev *dev) +{ + pci_no_msi(); + pci_warn(dev, "MSI quirk detected; MSI disabled\n"); +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_GCNB_LE, quirk_disable_all_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS400_200, quirk_disable_all_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS480, quirk_disable_all_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3336, quirk_disable_all_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3351, quirk_disable_all_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3364, quirk_disable_all_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8380_0, quirk_disable_all_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, 0x0761, quirk_disable_all_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SAMSUNG, 0xa5e3, quirk_disable_all_msi); + +/* Disable MSI on chipsets that are known to not support it */ +static void quirk_disable_msi(struct pci_dev *dev) +{ + if (dev->subordinate) { + pci_warn(dev, "MSI quirk detected; subordinate MSI disabled\n"); + dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MSI; + } +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, 0xa238, quirk_disable_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x5a3f, quirk_disable_msi); + +/* + * The APC bridge device in AMD 780 family northbridges has some random + * OEM subsystem ID in its vendor ID register (erratum 18), so instead + * we use the possible vendor/device IDs of the host bridge for the + * declared quirk, and search for the APC bridge by slot number. + */ +static void quirk_amd_780_apc_msi(struct pci_dev *host_bridge) +{ + struct pci_dev *apc_bridge; + + apc_bridge = pci_get_slot(host_bridge->bus, PCI_DEVFN(1, 0)); + if (apc_bridge) { + if (apc_bridge->device == 0x9602) + quirk_disable_msi(apc_bridge); + pci_dev_put(apc_bridge); + } +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x9600, quirk_amd_780_apc_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x9601, quirk_amd_780_apc_msi); + +/* + * Go through the list of HyperTransport capabilities and return 1 if a HT + * MSI capability is found and enabled. + */ +static int msi_ht_cap_enabled(struct pci_dev *dev) +{ + int pos, ttl = PCI_FIND_CAP_TTL; + + pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING); + while (pos && ttl--) { + u8 flags; + + if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS, + &flags) == 0) { + pci_info(dev, "Found %s HT MSI Mapping\n", + flags & HT_MSI_FLAGS_ENABLE ? + "enabled" : "disabled"); + return (flags & HT_MSI_FLAGS_ENABLE) != 0; + } + + pos = pci_find_next_ht_capability(dev, pos, + HT_CAPTYPE_MSI_MAPPING); + } + return 0; +} + +/* Check the HyperTransport MSI mapping to know whether MSI is enabled or not */ +static void quirk_msi_ht_cap(struct pci_dev *dev) +{ + if (!msi_ht_cap_enabled(dev)) + quirk_disable_msi(dev); +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT2000_PCIE, + quirk_msi_ht_cap); + +/* + * The nVidia CK804 chipset may have 2 HT MSI mappings. MSI is supported + * if the MSI capability is set in any of these mappings. + */ +static void quirk_nvidia_ck804_msi_ht_cap(struct pci_dev *dev) +{ + struct pci_dev *pdev; + + /* + * Check HT MSI cap on this chipset and the root one. A single one + * having MSI is enough to be sure that MSI is supported. + */ + pdev = pci_get_slot(dev->bus, 0); + if (!pdev) + return; + if (!msi_ht_cap_enabled(pdev)) + quirk_msi_ht_cap(dev); + pci_dev_put(pdev); +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_CK804_PCIE, + quirk_nvidia_ck804_msi_ht_cap); + +/* Force enable MSI mapping capability on HT bridges */ +static void ht_enable_msi_mapping(struct pci_dev *dev) +{ + int pos, ttl = PCI_FIND_CAP_TTL; + + pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING); + while (pos && ttl--) { + u8 flags; + + if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS, + &flags) == 0) { + pci_info(dev, "Enabling HT MSI Mapping\n"); + + pci_write_config_byte(dev, pos + HT_MSI_FLAGS, + flags | HT_MSI_FLAGS_ENABLE); + } + pos = pci_find_next_ht_capability(dev, pos, + HT_CAPTYPE_MSI_MAPPING); + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SERVERWORKS, + PCI_DEVICE_ID_SERVERWORKS_HT1000_PXB, + ht_enable_msi_mapping); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE, + ht_enable_msi_mapping); + +/* + * The P5N32-SLI motherboards from Asus have a problem with MSI + * for the MCP55 NIC. It is not yet determined whether the MSI problem + * also affects other devices. As for now, turn off MSI for this device. + */ +static void nvenet_msi_disable(struct pci_dev *dev) +{ + const char *board_name = dmi_get_system_info(DMI_BOARD_NAME); + + if (board_name && + (strstr(board_name, "P5N32-SLI PREMIUM") || + strstr(board_name, "P5N32-E SLI"))) { + pci_info(dev, "Disabling MSI for MCP55 NIC on P5N32-SLI\n"); + dev->no_msi = 1; + } +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA, + PCI_DEVICE_ID_NVIDIA_NVENET_15, + nvenet_msi_disable); + +/* + * PCIe spec r6.0 sec 6.1.4.3 says that if MSI/MSI-X is enabled, the device + * can't use INTx interrupts. Tegra's PCIe Root Ports don't generate MSI + * interrupts for PME and AER events; instead only INTx interrupts are + * generated. Though Tegra's PCIe Root Ports can generate MSI interrupts + * for other events, since PCIe specification doesn't support using a mix of + * INTx and MSI/MSI-X, it is required to disable MSI interrupts to avoid port + * service drivers registering their respective ISRs for MSIs. + */ +static void pci_quirk_nvidia_tegra_disable_rp_msi(struct pci_dev *dev) +{ + dev->no_msi = 1; +} +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x1ad0, + PCI_CLASS_BRIDGE_PCI, 8, + pci_quirk_nvidia_tegra_disable_rp_msi); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x1ad1, + PCI_CLASS_BRIDGE_PCI, 8, + pci_quirk_nvidia_tegra_disable_rp_msi); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x1ad2, + PCI_CLASS_BRIDGE_PCI, 8, + pci_quirk_nvidia_tegra_disable_rp_msi); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0bf0, + PCI_CLASS_BRIDGE_PCI, 8, + pci_quirk_nvidia_tegra_disable_rp_msi); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0bf1, + PCI_CLASS_BRIDGE_PCI, 8, + pci_quirk_nvidia_tegra_disable_rp_msi); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0e1c, + PCI_CLASS_BRIDGE_PCI, 8, + pci_quirk_nvidia_tegra_disable_rp_msi); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0e1d, + PCI_CLASS_BRIDGE_PCI, 8, + pci_quirk_nvidia_tegra_disable_rp_msi); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0e12, + PCI_CLASS_BRIDGE_PCI, 8, + pci_quirk_nvidia_tegra_disable_rp_msi); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0e13, + PCI_CLASS_BRIDGE_PCI, 8, + pci_quirk_nvidia_tegra_disable_rp_msi); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0fae, + PCI_CLASS_BRIDGE_PCI, 8, + pci_quirk_nvidia_tegra_disable_rp_msi); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0faf, + PCI_CLASS_BRIDGE_PCI, 8, + pci_quirk_nvidia_tegra_disable_rp_msi); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x10e5, + PCI_CLASS_BRIDGE_PCI, 8, + pci_quirk_nvidia_tegra_disable_rp_msi); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x10e6, + PCI_CLASS_BRIDGE_PCI, 8, + pci_quirk_nvidia_tegra_disable_rp_msi); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x229a, + PCI_CLASS_BRIDGE_PCI, 8, + pci_quirk_nvidia_tegra_disable_rp_msi); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x229c, + PCI_CLASS_BRIDGE_PCI, 8, + pci_quirk_nvidia_tegra_disable_rp_msi); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x229e, + PCI_CLASS_BRIDGE_PCI, 8, + pci_quirk_nvidia_tegra_disable_rp_msi); + +/* + * Some versions of the MCP55 bridge from Nvidia have a legacy IRQ routing + * config register. This register controls the routing of legacy + * interrupts from devices that route through the MCP55. If this register + * is misprogrammed, interrupts are only sent to the BSP, unlike + * conventional systems where the IRQ is broadcast to all online CPUs. Not + * having this register set properly prevents kdump from booting up + * properly, so let's make sure that we have it set correctly. + * Note that this is an undocumented register. + */ +static void nvbridge_check_legacy_irq_routing(struct pci_dev *dev) +{ + u32 cfg; + + if (!pci_find_capability(dev, PCI_CAP_ID_HT)) + return; + + pci_read_config_dword(dev, 0x74, &cfg); + + if (cfg & ((1 << 2) | (1 << 15))) { + pr_info("Rewriting IRQ routing register on MCP55\n"); + cfg &= ~((1 << 2) | (1 << 15)); + pci_write_config_dword(dev, 0x74, cfg); + } +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA, + PCI_DEVICE_ID_NVIDIA_MCP55_BRIDGE_V0, + nvbridge_check_legacy_irq_routing); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA, + PCI_DEVICE_ID_NVIDIA_MCP55_BRIDGE_V4, + nvbridge_check_legacy_irq_routing); + +static int ht_check_msi_mapping(struct pci_dev *dev) +{ + int pos, ttl = PCI_FIND_CAP_TTL; + int found = 0; + + /* Check if there is HT MSI cap or enabled on this device */ + pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING); + while (pos && ttl--) { + u8 flags; + + if (found < 1) + found = 1; + if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS, + &flags) == 0) { + if (flags & HT_MSI_FLAGS_ENABLE) { + if (found < 2) { + found = 2; + break; + } + } + } + pos = pci_find_next_ht_capability(dev, pos, + HT_CAPTYPE_MSI_MAPPING); + } + + return found; +} + +static int host_bridge_with_leaf(struct pci_dev *host_bridge) +{ + struct pci_dev *dev; + int pos; + int i, dev_no; + int found = 0; + + dev_no = host_bridge->devfn >> 3; + for (i = dev_no + 1; i < 0x20; i++) { + dev = pci_get_slot(host_bridge->bus, PCI_DEVFN(i, 0)); + if (!dev) + continue; + + /* found next host bridge? */ + pos = pci_find_ht_capability(dev, HT_CAPTYPE_SLAVE); + if (pos != 0) { + pci_dev_put(dev); + break; + } + + if (ht_check_msi_mapping(dev)) { + found = 1; + pci_dev_put(dev); + break; + } + pci_dev_put(dev); + } + + return found; +} + +#define PCI_HT_CAP_SLAVE_CTRL0 4 /* link control */ +#define PCI_HT_CAP_SLAVE_CTRL1 8 /* link control to */ + +static int is_end_of_ht_chain(struct pci_dev *dev) +{ + int pos, ctrl_off; + int end = 0; + u16 flags, ctrl; + + pos = pci_find_ht_capability(dev, HT_CAPTYPE_SLAVE); + + if (!pos) + goto out; + + pci_read_config_word(dev, pos + PCI_CAP_FLAGS, &flags); + + ctrl_off = ((flags >> 10) & 1) ? + PCI_HT_CAP_SLAVE_CTRL0 : PCI_HT_CAP_SLAVE_CTRL1; + pci_read_config_word(dev, pos + ctrl_off, &ctrl); + + if (ctrl & (1 << 6)) + end = 1; + +out: + return end; +} + +static void nv_ht_enable_msi_mapping(struct pci_dev *dev) +{ + struct pci_dev *host_bridge; + int pos; + int i, dev_no; + int found = 0; + + dev_no = dev->devfn >> 3; + for (i = dev_no; i >= 0; i--) { + host_bridge = pci_get_slot(dev->bus, PCI_DEVFN(i, 0)); + if (!host_bridge) + continue; + + pos = pci_find_ht_capability(host_bridge, HT_CAPTYPE_SLAVE); + if (pos != 0) { + found = 1; + break; + } + pci_dev_put(host_bridge); + } + + if (!found) + return; + + /* don't enable end_device/host_bridge with leaf directly here */ + if (host_bridge == dev && is_end_of_ht_chain(host_bridge) && + host_bridge_with_leaf(host_bridge)) + goto out; + + /* root did that ! */ + if (msi_ht_cap_enabled(host_bridge)) + goto out; + + ht_enable_msi_mapping(dev); + +out: + pci_dev_put(host_bridge); +} + +static void ht_disable_msi_mapping(struct pci_dev *dev) +{ + int pos, ttl = PCI_FIND_CAP_TTL; + + pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING); + while (pos && ttl--) { + u8 flags; + + if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS, + &flags) == 0) { + pci_info(dev, "Disabling HT MSI Mapping\n"); + + pci_write_config_byte(dev, pos + HT_MSI_FLAGS, + flags & ~HT_MSI_FLAGS_ENABLE); + } + pos = pci_find_next_ht_capability(dev, pos, + HT_CAPTYPE_MSI_MAPPING); + } +} + +static void __nv_msi_ht_cap_quirk(struct pci_dev *dev, int all) +{ + struct pci_dev *host_bridge; + int pos; + int found; + + if (!pci_msi_enabled()) + return; + + /* check if there is HT MSI cap or enabled on this device */ + found = ht_check_msi_mapping(dev); + + /* no HT MSI CAP */ + if (found == 0) + return; + + /* + * HT MSI mapping should be disabled on devices that are below + * a non-HyperTransport host bridge. Locate the host bridge. + */ + host_bridge = pci_get_domain_bus_and_slot(pci_domain_nr(dev->bus), 0, + PCI_DEVFN(0, 0)); + if (host_bridge == NULL) { + pci_warn(dev, "nv_msi_ht_cap_quirk didn't locate host bridge\n"); + return; + } + + pos = pci_find_ht_capability(host_bridge, HT_CAPTYPE_SLAVE); + if (pos != 0) { + /* Host bridge is to HT */ + if (found == 1) { + /* it is not enabled, try to enable it */ + if (all) + ht_enable_msi_mapping(dev); + else + nv_ht_enable_msi_mapping(dev); + } + goto out; + } + + /* HT MSI is not enabled */ + if (found == 1) + goto out; + + /* Host bridge is not to HT, disable HT MSI mapping on this device */ + ht_disable_msi_mapping(dev); + +out: + pci_dev_put(host_bridge); +} + +static void nv_msi_ht_cap_quirk_all(struct pci_dev *dev) +{ + return __nv_msi_ht_cap_quirk(dev, 1); +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_ANY_ID, nv_msi_ht_cap_quirk_all); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AL, PCI_ANY_ID, nv_msi_ht_cap_quirk_all); + +static void nv_msi_ht_cap_quirk_leaf(struct pci_dev *dev) +{ + return __nv_msi_ht_cap_quirk(dev, 0); +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, nv_msi_ht_cap_quirk_leaf); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, nv_msi_ht_cap_quirk_leaf); + +static void quirk_msi_intx_disable_bug(struct pci_dev *dev) +{ + dev->dev_flags |= PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG; +} + +static void quirk_msi_intx_disable_ati_bug(struct pci_dev *dev) +{ + struct pci_dev *p; + + /* + * SB700 MSI issue will be fixed at HW level from revision A21; + * we need check PCI REVISION ID of SMBus controller to get SB700 + * revision. + */ + p = pci_get_device(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_SBX00_SMBUS, + NULL); + if (!p) + return; + + if ((p->revision < 0x3B) && (p->revision >= 0x30)) + dev->dev_flags |= PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG; + pci_dev_put(p); +} + +static void quirk_msi_intx_disable_qca_bug(struct pci_dev *dev) +{ + /* AR816X/AR817X/E210X MSI is fixed at HW level from revision 0x18 */ + if (dev->revision < 0x18) { + pci_info(dev, "set MSI_INTX_DISABLE_BUG flag\n"); + dev->dev_flags |= PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG; + } +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, + PCI_DEVICE_ID_TIGON3_5780, + quirk_msi_intx_disable_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, + PCI_DEVICE_ID_TIGON3_5780S, + quirk_msi_intx_disable_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, + PCI_DEVICE_ID_TIGON3_5714, + quirk_msi_intx_disable_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, + PCI_DEVICE_ID_TIGON3_5714S, + quirk_msi_intx_disable_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, + PCI_DEVICE_ID_TIGON3_5715, + quirk_msi_intx_disable_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, + PCI_DEVICE_ID_TIGON3_5715S, + quirk_msi_intx_disable_bug); + +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4390, + quirk_msi_intx_disable_ati_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4391, + quirk_msi_intx_disable_ati_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4392, + quirk_msi_intx_disable_ati_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4393, + quirk_msi_intx_disable_ati_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4394, + quirk_msi_intx_disable_ati_bug); + +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4373, + quirk_msi_intx_disable_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4374, + quirk_msi_intx_disable_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4375, + quirk_msi_intx_disable_bug); + +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x1062, + quirk_msi_intx_disable_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x1063, + quirk_msi_intx_disable_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x2060, + quirk_msi_intx_disable_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x2062, + quirk_msi_intx_disable_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x1073, + quirk_msi_intx_disable_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x1083, + quirk_msi_intx_disable_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x1090, + quirk_msi_intx_disable_qca_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x1091, + quirk_msi_intx_disable_qca_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x10a0, + quirk_msi_intx_disable_qca_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x10a1, + quirk_msi_intx_disable_qca_bug); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0xe091, + quirk_msi_intx_disable_qca_bug); + +/* + * Amazon's Annapurna Labs 1c36:0031 Root Ports don't support MSI-X, so it + * should be disabled on platforms where the device (mistakenly) advertises it. + * + * Notice that this quirk also disables MSI (which may work, but hasn't been + * tested), since currently there is no standard way to disable only MSI-X. + * + * The 0031 device id is reused for other non Root Port device types, + * therefore the quirk is registered for the PCI_CLASS_BRIDGE_PCI class. + */ +static void quirk_al_msi_disable(struct pci_dev *dev) +{ + dev->no_msi = 1; + pci_warn(dev, "Disabling MSI/MSI-X\n"); +} +DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_AMAZON_ANNAPURNA_LABS, 0x0031, + PCI_CLASS_BRIDGE_PCI, 8, quirk_al_msi_disable); +#endif /* CONFIG_PCI_MSI */ + +/* + * Allow manual resource allocation for PCI hotplug bridges via + * pci=hpmemsize=nnM and pci=hpiosize=nnM parameters. For some PCI-PCI + * hotplug bridges, like PLX 6254 (former HINT HB6), kernel fails to + * allocate resources when hotplug device is inserted and PCI bus is + * rescanned. + */ +static void quirk_hotplug_bridge(struct pci_dev *dev) +{ + dev->is_hotplug_bridge = 1; +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_HINT, 0x0020, quirk_hotplug_bridge); + +/* + * This is a quirk for the Ricoh MMC controller found as a part of some + * multifunction chips. + * + * This is very similar and based on the ricoh_mmc driver written by + * Philip Langdale. Thank you for these magic sequences. + * + * These chips implement the four main memory card controllers (SD, MMC, + * MS, xD) and one or both of CardBus or FireWire. + * + * It happens that they implement SD and MMC support as separate + * controllers (and PCI functions). The Linux SDHCI driver supports MMC + * cards but the chip detects MMC cards in hardware and directs them to the + * MMC controller - so the SDHCI driver never sees them. + * + * To get around this, we must disable the useless MMC controller. At that + * point, the SDHCI controller will start seeing them. It seems to be the + * case that the relevant PCI registers to deactivate the MMC controller + * live on PCI function 0, which might be the CardBus controller or the + * FireWire controller, depending on the particular chip in question + * + * This has to be done early, because as soon as we disable the MMC controller + * other PCI functions shift up one level, e.g. function #2 becomes function + * #1, and this will confuse the PCI core. + */ +#ifdef CONFIG_MMC_RICOH_MMC +static void ricoh_mmc_fixup_rl5c476(struct pci_dev *dev) +{ + u8 write_enable; + u8 write_target; + u8 disable; + + /* + * Disable via CardBus interface + * + * This must be done via function #0 + */ + if (PCI_FUNC(dev->devfn)) + return; + + pci_read_config_byte(dev, 0xB7, &disable); + if (disable & 0x02) + return; + + pci_read_config_byte(dev, 0x8E, &write_enable); + pci_write_config_byte(dev, 0x8E, 0xAA); + pci_read_config_byte(dev, 0x8D, &write_target); + pci_write_config_byte(dev, 0x8D, 0xB7); + pci_write_config_byte(dev, 0xB7, disable | 0x02); + pci_write_config_byte(dev, 0x8E, write_enable); + pci_write_config_byte(dev, 0x8D, write_target); + + pci_notice(dev, "proprietary Ricoh MMC controller disabled (via CardBus function)\n"); + pci_notice(dev, "MMC cards are now supported by standard SDHCI controller\n"); +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_RL5C476, ricoh_mmc_fixup_rl5c476); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_RL5C476, ricoh_mmc_fixup_rl5c476); + +static void ricoh_mmc_fixup_r5c832(struct pci_dev *dev) +{ + u8 write_enable; + u8 disable; + + /* + * Disable via FireWire interface + * + * This must be done via function #0 + */ + if (PCI_FUNC(dev->devfn)) + return; + /* + * RICOH 0xe822 and 0xe823 SD/MMC card readers fail to recognize + * certain types of SD/MMC cards. Lowering the SD base clock + * frequency from 200Mhz to 50Mhz fixes this issue. + * + * 0x150 - SD2.0 mode enable for changing base clock + * frequency to 50Mhz + * 0xe1 - Base clock frequency + * 0x32 - 50Mhz new clock frequency + * 0xf9 - Key register for 0x150 + * 0xfc - key register for 0xe1 + */ + if (dev->device == PCI_DEVICE_ID_RICOH_R5CE822 || + dev->device == PCI_DEVICE_ID_RICOH_R5CE823) { + pci_write_config_byte(dev, 0xf9, 0xfc); + pci_write_config_byte(dev, 0x150, 0x10); + pci_write_config_byte(dev, 0xf9, 0x00); + pci_write_config_byte(dev, 0xfc, 0x01); + pci_write_config_byte(dev, 0xe1, 0x32); + pci_write_config_byte(dev, 0xfc, 0x00); + + pci_notice(dev, "MMC controller base frequency changed to 50Mhz.\n"); + } + + pci_read_config_byte(dev, 0xCB, &disable); + + if (disable & 0x02) + return; + + pci_read_config_byte(dev, 0xCA, &write_enable); + pci_write_config_byte(dev, 0xCA, 0x57); + pci_write_config_byte(dev, 0xCB, disable | 0x02); + pci_write_config_byte(dev, 0xCA, write_enable); + + pci_notice(dev, "proprietary Ricoh MMC controller disabled (via FireWire function)\n"); + pci_notice(dev, "MMC cards are now supported by standard SDHCI controller\n"); + +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, ricoh_mmc_fixup_r5c832); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, ricoh_mmc_fixup_r5c832); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5CE822, ricoh_mmc_fixup_r5c832); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5CE822, ricoh_mmc_fixup_r5c832); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5CE823, ricoh_mmc_fixup_r5c832); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5CE823, ricoh_mmc_fixup_r5c832); +#endif /*CONFIG_MMC_RICOH_MMC*/ + +#ifdef CONFIG_DMAR_TABLE +#define VTUNCERRMSK_REG 0x1ac +#define VTD_MSK_SPEC_ERRORS (1 << 31) +/* + * This is a quirk for masking VT-d spec-defined errors to platform error + * handling logic. Without this, platforms using Intel 7500, 5500 chipsets + * (and the derivative chipsets like X58 etc) seem to generate NMI/SMI (based + * on the RAS config settings of the platform) when a VT-d fault happens. + * The resulting SMI caused the system to hang. + * + * VT-d spec-related errors are already handled by the VT-d OS code, so no + * need to report the same error through other channels. + */ +static void vtd_mask_spec_errors(struct pci_dev *dev) +{ + u32 word; + + pci_read_config_dword(dev, VTUNCERRMSK_REG, &word); + pci_write_config_dword(dev, VTUNCERRMSK_REG, word | VTD_MSK_SPEC_ERRORS); +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x342e, vtd_mask_spec_errors); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x3c28, vtd_mask_spec_errors); +#endif + +static void fixup_ti816x_class(struct pci_dev *dev) +{ + u32 class = dev->class; + + /* TI 816x devices do not have class code set when in PCIe boot mode */ + dev->class = PCI_CLASS_MULTIMEDIA_VIDEO << 8; + pci_info(dev, "PCI class overridden (%#08x -> %#08x)\n", + class, dev->class); +} +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_TI, 0xb800, + PCI_CLASS_NOT_DEFINED, 8, fixup_ti816x_class); + +/* + * Some PCIe devices do not work reliably with the claimed maximum + * payload size supported. + */ +static void fixup_mpss_256(struct pci_dev *dev) +{ + dev->pcie_mpss = 1; /* 256 bytes */ +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SOLARFLARE, + PCI_DEVICE_ID_SOLARFLARE_SFC4000A_0, fixup_mpss_256); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SOLARFLARE, + PCI_DEVICE_ID_SOLARFLARE_SFC4000A_1, fixup_mpss_256); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SOLARFLARE, + PCI_DEVICE_ID_SOLARFLARE_SFC4000B, fixup_mpss_256); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_ASMEDIA, 0x0612, fixup_mpss_256); + +/* + * Intel 5000 and 5100 Memory controllers have an erratum with read completion + * coalescing (which is enabled by default on some BIOSes) and MPS of 256B. + * Since there is no way of knowing what the PCIe MPS on each fabric will be + * until all of the devices are discovered and buses walked, read completion + * coalescing must be disabled. Unfortunately, it cannot be re-enabled because + * it is possible to hotplug a device with MPS of 256B. + */ +static void quirk_intel_mc_errata(struct pci_dev *dev) +{ + int err; + u16 rcc; + + if (pcie_bus_config == PCIE_BUS_TUNE_OFF || + pcie_bus_config == PCIE_BUS_DEFAULT) + return; + + /* + * Intel erratum specifies bits to change but does not say what + * they are. Keeping them magical until such time as the registers + * and values can be explained. + */ + err = pci_read_config_word(dev, 0x48, &rcc); + if (err) { + pci_err(dev, "Error attempting to read the read completion coalescing register\n"); + return; + } + + if (!(rcc & (1 << 10))) + return; + + rcc &= ~(1 << 10); + + err = pci_write_config_word(dev, 0x48, rcc); + if (err) { + pci_err(dev, "Error attempting to write the read completion coalescing register\n"); + return; + } + + pr_info_once("Read completion coalescing disabled due to hardware erratum relating to 256B MPS\n"); +} +/* Intel 5000 series memory controllers and ports 2-7 */ +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25c0, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25d0, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25d4, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25d8, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e2, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e3, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e4, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e5, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e6, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e7, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25f7, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25f8, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25f9, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25fa, quirk_intel_mc_errata); +/* Intel 5100 series memory controllers and ports 2-7 */ +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65c0, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e2, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e3, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e4, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e5, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e6, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e7, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65f7, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65f8, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65f9, quirk_intel_mc_errata); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65fa, quirk_intel_mc_errata); + +/* + * Ivytown NTB BAR sizes are misreported by the hardware due to an erratum. + * To work around this, query the size it should be configured to by the + * device and modify the resource end to correspond to this new size. + */ +static void quirk_intel_ntb(struct pci_dev *dev) +{ + int rc; + u8 val; + + rc = pci_read_config_byte(dev, 0x00D0, &val); + if (rc) + return; + + dev->resource[2].end = dev->resource[2].start + ((u64) 1 << val) - 1; + + rc = pci_read_config_byte(dev, 0x00D1, &val); + if (rc) + return; + + dev->resource[4].end = dev->resource[4].start + ((u64) 1 << val) - 1; +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x0e08, quirk_intel_ntb); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x0e0d, quirk_intel_ntb); + +/* + * Some BIOS implementations leave the Intel GPU interrupts enabled, even + * though no one is handling them (e.g., if the i915 driver is never + * loaded). Additionally the interrupt destination is not set up properly + * and the interrupt ends up -somewhere-. + * + * These spurious interrupts are "sticky" and the kernel disables the + * (shared) interrupt line after 100,000+ generated interrupts. + * + * Fix it by disabling the still enabled interrupts. This resolves crashes + * often seen on monitor unplug. + */ +#define I915_DEIER_REG 0x4400c +static void disable_igfx_irq(struct pci_dev *dev) +{ + void __iomem *regs = pci_iomap(dev, 0, 0); + if (regs == NULL) { + pci_warn(dev, "igfx quirk: Can't iomap PCI device\n"); + return; + } + + /* Check if any interrupt line is still enabled */ + if (readl(regs + I915_DEIER_REG) != 0) { + pci_warn(dev, "BIOS left Intel GPU interrupts enabled; disabling\n"); + + writel(0, regs + I915_DEIER_REG); + } + + pci_iounmap(dev, regs); +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0042, disable_igfx_irq); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0046, disable_igfx_irq); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x004a, disable_igfx_irq); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0102, disable_igfx_irq); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0106, disable_igfx_irq); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x010a, disable_igfx_irq); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0152, disable_igfx_irq); + +/* + * PCI devices which are on Intel chips can skip the 10ms delay + * before entering D3 mode. + */ +static void quirk_remove_d3hot_delay(struct pci_dev *dev) +{ + dev->d3hot_delay = 0; +} +/* C600 Series devices do not need 10ms d3hot_delay */ +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0412, quirk_remove_d3hot_delay); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0c00, quirk_remove_d3hot_delay); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0c0c, quirk_remove_d3hot_delay); +/* Lynxpoint-H PCH devices do not need 10ms d3hot_delay */ +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c02, quirk_remove_d3hot_delay); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c18, quirk_remove_d3hot_delay); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c1c, quirk_remove_d3hot_delay); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c20, quirk_remove_d3hot_delay); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c22, quirk_remove_d3hot_delay); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c26, quirk_remove_d3hot_delay); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c2d, quirk_remove_d3hot_delay); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c31, quirk_remove_d3hot_delay); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c3a, quirk_remove_d3hot_delay); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c3d, quirk_remove_d3hot_delay); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c4e, quirk_remove_d3hot_delay); +/* Intel Cherrytrail devices do not need 10ms d3hot_delay */ +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2280, quirk_remove_d3hot_delay); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2298, quirk_remove_d3hot_delay); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x229c, quirk_remove_d3hot_delay); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b0, quirk_remove_d3hot_delay); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b5, quirk_remove_d3hot_delay); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b7, quirk_remove_d3hot_delay); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b8, quirk_remove_d3hot_delay); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22d8, quirk_remove_d3hot_delay); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22dc, quirk_remove_d3hot_delay); + +/* + * Some devices may pass our check in pci_intx_mask_supported() if + * PCI_COMMAND_INTX_DISABLE works though they actually do not properly + * support this feature. + */ +static void quirk_broken_intx_masking(struct pci_dev *dev) +{ + dev->broken_intx_masking = 1; +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CHELSIO, 0x0030, + quirk_broken_intx_masking); +DECLARE_PCI_FIXUP_FINAL(0x1814, 0x0601, /* Ralink RT2800 802.11n PCI */ + quirk_broken_intx_masking); +DECLARE_PCI_FIXUP_FINAL(0x1b7c, 0x0004, /* Ceton InfiniTV4 */ + quirk_broken_intx_masking); + +/* + * Realtek RTL8169 PCI Gigabit Ethernet Controller (rev 10) + * Subsystem: Realtek RTL8169/8110 Family PCI Gigabit Ethernet NIC + * + * RTL8110SC - Fails under PCI device assignment using DisINTx masking. + */ +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_REALTEK, 0x8169, + quirk_broken_intx_masking); + +/* + * Intel i40e (XL710/X710) 10/20/40GbE NICs all have broken INTx masking, + * DisINTx can be set but the interrupt status bit is non-functional. + */ +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1572, quirk_broken_intx_masking); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1574, quirk_broken_intx_masking); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1580, quirk_broken_intx_masking); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1581, quirk_broken_intx_masking); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1583, quirk_broken_intx_masking); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1584, quirk_broken_intx_masking); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1585, quirk_broken_intx_masking); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1586, quirk_broken_intx_masking); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1587, quirk_broken_intx_masking); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1588, quirk_broken_intx_masking); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1589, quirk_broken_intx_masking); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x158a, quirk_broken_intx_masking); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x158b, quirk_broken_intx_masking); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x37d0, quirk_broken_intx_masking); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x37d1, quirk_broken_intx_masking); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x37d2, quirk_broken_intx_masking); + +static u16 mellanox_broken_intx_devs[] = { + PCI_DEVICE_ID_MELLANOX_HERMON_SDR, + PCI_DEVICE_ID_MELLANOX_HERMON_DDR, + PCI_DEVICE_ID_MELLANOX_HERMON_QDR, + PCI_DEVICE_ID_MELLANOX_HERMON_DDR_GEN2, + PCI_DEVICE_ID_MELLANOX_HERMON_QDR_GEN2, + PCI_DEVICE_ID_MELLANOX_HERMON_EN, + PCI_DEVICE_ID_MELLANOX_HERMON_EN_GEN2, + PCI_DEVICE_ID_MELLANOX_CONNECTX_EN, + PCI_DEVICE_ID_MELLANOX_CONNECTX_EN_T_GEN2, + PCI_DEVICE_ID_MELLANOX_CONNECTX_EN_GEN2, + PCI_DEVICE_ID_MELLANOX_CONNECTX_EN_5_GEN2, + PCI_DEVICE_ID_MELLANOX_CONNECTX2, + PCI_DEVICE_ID_MELLANOX_CONNECTX3, + PCI_DEVICE_ID_MELLANOX_CONNECTX3_PRO, +}; + +#define CONNECTX_4_CURR_MAX_MINOR 99 +#define CONNECTX_4_INTX_SUPPORT_MINOR 14 + +/* + * Check ConnectX-4/LX FW version to see if it supports legacy interrupts. + * If so, don't mark it as broken. + * FW minor > 99 means older FW version format and no INTx masking support. + * FW minor < 14 means new FW version format and no INTx masking support. + */ +static void mellanox_check_broken_intx_masking(struct pci_dev *pdev) +{ + __be32 __iomem *fw_ver; + u16 fw_major; + u16 fw_minor; + u16 fw_subminor; + u32 fw_maj_min; + u32 fw_sub_min; + int i; + + for (i = 0; i < ARRAY_SIZE(mellanox_broken_intx_devs); i++) { + if (pdev->device == mellanox_broken_intx_devs[i]) { + pdev->broken_intx_masking = 1; + return; + } + } + + /* + * Getting here means Connect-IB cards and up. Connect-IB has no INTx + * support so shouldn't be checked further + */ + if (pdev->device == PCI_DEVICE_ID_MELLANOX_CONNECTIB) + return; + + if (pdev->device != PCI_DEVICE_ID_MELLANOX_CONNECTX4 && + pdev->device != PCI_DEVICE_ID_MELLANOX_CONNECTX4_LX) + return; + + /* For ConnectX-4 and ConnectX-4LX, need to check FW support */ + if (pci_enable_device_mem(pdev)) { + pci_warn(pdev, "Can't enable device memory\n"); + return; + } + + fw_ver = ioremap(pci_resource_start(pdev, 0), 4); + if (!fw_ver) { + pci_warn(pdev, "Can't map ConnectX-4 initialization segment\n"); + goto out; + } + + /* Reading from resource space should be 32b aligned */ + fw_maj_min = ioread32be(fw_ver); + fw_sub_min = ioread32be(fw_ver + 1); + fw_major = fw_maj_min & 0xffff; + fw_minor = fw_maj_min >> 16; + fw_subminor = fw_sub_min & 0xffff; + if (fw_minor > CONNECTX_4_CURR_MAX_MINOR || + fw_minor < CONNECTX_4_INTX_SUPPORT_MINOR) { + pci_warn(pdev, "ConnectX-4: FW %u.%u.%u doesn't support INTx masking, disabling. Please upgrade FW to %d.14.1100 and up for INTx support\n", + fw_major, fw_minor, fw_subminor, pdev->device == + PCI_DEVICE_ID_MELLANOX_CONNECTX4 ? 12 : 14); + pdev->broken_intx_masking = 1; + } + + iounmap(fw_ver); + +out: + pci_disable_device(pdev); +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_MELLANOX, PCI_ANY_ID, + mellanox_check_broken_intx_masking); + +static void quirk_no_bus_reset(struct pci_dev *dev) +{ + dev->dev_flags |= PCI_DEV_FLAGS_NO_BUS_RESET; +} + +/* + * Some NVIDIA GPU devices do not work with bus reset, SBR needs to be + * prevented for those affected devices. + */ +static void quirk_nvidia_no_bus_reset(struct pci_dev *dev) +{ + if ((dev->device & 0xffc0) == 0x2340) + quirk_no_bus_reset(dev); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, + quirk_nvidia_no_bus_reset); + +/* + * Some Atheros AR9xxx and QCA988x chips do not behave after a bus reset. + * The device will throw a Link Down error on AER-capable systems and + * regardless of AER, config space of the device is never accessible again + * and typically causes the system to hang or reset when access is attempted. + * https://lore.kernel.org/r/20140923210318.498dacbd@dualc.maya.org/ + */ +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x0030, quirk_no_bus_reset); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x0032, quirk_no_bus_reset); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x003c, quirk_no_bus_reset); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x0033, quirk_no_bus_reset); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x0034, quirk_no_bus_reset); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x003e, quirk_no_bus_reset); + +/* + * Root port on some Cavium CN8xxx chips do not successfully complete a bus + * reset when used with certain child devices. After the reset, config + * accesses to the child may fail. + */ +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_CAVIUM, 0xa100, quirk_no_bus_reset); + +/* + * Some TI KeyStone C667X devices do not support bus/hot reset. The PCIESS + * automatically disables LTSSM when Secondary Bus Reset is received and + * the device stops working. Prevent bus reset for these devices. With + * this change, the device can be assigned to VMs with VFIO, but it will + * leak state between VMs. Reference + * https://e2e.ti.com/support/processors/f/791/t/954382 + */ +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TI, 0xb005, quirk_no_bus_reset); + +static void quirk_no_pm_reset(struct pci_dev *dev) +{ + /* + * We can't do a bus reset on root bus devices, but an ineffective + * PM reset may be better than nothing. + */ + if (!pci_is_root_bus(dev->bus)) + dev->dev_flags |= PCI_DEV_FLAGS_NO_PM_RESET; +} + +/* + * Some AMD/ATI GPUS (HD8570 - Oland) report that a D3hot->D0 transition + * causes a reset (i.e., they advertise NoSoftRst-). This transition seems + * to have no effect on the device: it retains the framebuffer contents and + * monitor sync. Advertising this support makes other layers, like VFIO, + * assume pci_reset_function() is viable for this device. Mark it as + * unavailable to skip it when testing reset methods. + */ +DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_VENDOR_ID_ATI, PCI_ANY_ID, + PCI_CLASS_DISPLAY_VGA, 8, quirk_no_pm_reset); + +/* + * Thunderbolt controllers with broken MSI hotplug signaling: + * Entire 1st generation (Light Ridge, Eagle Ridge, Light Peak) and part + * of the 2nd generation (Cactus Ridge 4C up to revision 1, Port Ridge). + */ +static void quirk_thunderbolt_hotplug_msi(struct pci_dev *pdev) +{ + if (pdev->is_hotplug_bridge && + (pdev->device != PCI_DEVICE_ID_INTEL_CACTUS_RIDGE_4C || + pdev->revision <= 1)) + pdev->no_msi = 1; +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_LIGHT_RIDGE, + quirk_thunderbolt_hotplug_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EAGLE_RIDGE, + quirk_thunderbolt_hotplug_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_LIGHT_PEAK, + quirk_thunderbolt_hotplug_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_CACTUS_RIDGE_4C, + quirk_thunderbolt_hotplug_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PORT_RIDGE, + quirk_thunderbolt_hotplug_msi); + +#ifdef CONFIG_ACPI +/* + * Apple: Shutdown Cactus Ridge Thunderbolt controller. + * + * On Apple hardware the Cactus Ridge Thunderbolt controller needs to be + * shutdown before suspend. Otherwise the native host interface (NHI) will not + * be present after resume if a device was plugged in before suspend. + * + * The Thunderbolt controller consists of a PCIe switch with downstream + * bridges leading to the NHI and to the tunnel PCI bridges. + * + * This quirk cuts power to the whole chip. Therefore we have to apply it + * during suspend_noirq of the upstream bridge. + * + * Power is automagically restored before resume. No action is needed. + */ +static void quirk_apple_poweroff_thunderbolt(struct pci_dev *dev) +{ + acpi_handle bridge, SXIO, SXFP, SXLV; + + if (!x86_apple_machine) + return; + if (pci_pcie_type(dev) != PCI_EXP_TYPE_UPSTREAM) + return; + + /* + * SXIO/SXFP/SXLF turns off power to the Thunderbolt controller. + * We don't know how to turn it back on again, but firmware does, + * so we can only use SXIO/SXFP/SXLF if we're suspending via + * firmware. + */ + if (!pm_suspend_via_firmware()) + return; + + bridge = ACPI_HANDLE(&dev->dev); + if (!bridge) + return; + + /* + * SXIO and SXLV are present only on machines requiring this quirk. + * Thunderbolt bridges in external devices might have the same + * device ID as those on the host, but they will not have the + * associated ACPI methods. This implicitly checks that we are at + * the right bridge. + */ + if (ACPI_FAILURE(acpi_get_handle(bridge, "DSB0.NHI0.SXIO", &SXIO)) + || ACPI_FAILURE(acpi_get_handle(bridge, "DSB0.NHI0.SXFP", &SXFP)) + || ACPI_FAILURE(acpi_get_handle(bridge, "DSB0.NHI0.SXLV", &SXLV))) + return; + pci_info(dev, "quirk: cutting power to Thunderbolt controller...\n"); + + /* magic sequence */ + acpi_execute_simple_method(SXIO, NULL, 1); + acpi_execute_simple_method(SXFP, NULL, 0); + msleep(300); + acpi_execute_simple_method(SXLV, NULL, 0); + acpi_execute_simple_method(SXIO, NULL, 0); + acpi_execute_simple_method(SXLV, NULL, 0); +} +DECLARE_PCI_FIXUP_SUSPEND_LATE(PCI_VENDOR_ID_INTEL, + PCI_DEVICE_ID_INTEL_CACTUS_RIDGE_4C, + quirk_apple_poweroff_thunderbolt); +#endif + +/* + * Following are device-specific reset methods which can be used to + * reset a single function if other methods (e.g. FLR, PM D0->D3) are + * not available. + */ +static int reset_intel_82599_sfp_virtfn(struct pci_dev *dev, bool probe) +{ + /* + * http://www.intel.com/content/dam/doc/datasheet/82599-10-gbe-controller-datasheet.pdf + * + * The 82599 supports FLR on VFs, but FLR support is reported only + * in the PF DEVCAP (sec 9.3.10.4), not in the VF DEVCAP (sec 9.5). + * Thus we must call pcie_flr() directly without first checking if it is + * supported. + */ + if (!probe) + pcie_flr(dev); + return 0; +} + +#define SOUTH_CHICKEN2 0xc2004 +#define PCH_PP_STATUS 0xc7200 +#define PCH_PP_CONTROL 0xc7204 +#define MSG_CTL 0x45010 +#define NSDE_PWR_STATE 0xd0100 +#define IGD_OPERATION_TIMEOUT 10000 /* set timeout 10 seconds */ + +static int reset_ivb_igd(struct pci_dev *dev, bool probe) +{ + void __iomem *mmio_base; + unsigned long timeout; + u32 val; + + if (probe) + return 0; + + mmio_base = pci_iomap(dev, 0, 0); + if (!mmio_base) + return -ENOMEM; + + iowrite32(0x00000002, mmio_base + MSG_CTL); + + /* + * Clobbering SOUTH_CHICKEN2 register is fine only if the next + * driver loaded sets the right bits. However, this's a reset and + * the bits have been set by i915 previously, so we clobber + * SOUTH_CHICKEN2 register directly here. + */ + iowrite32(0x00000005, mmio_base + SOUTH_CHICKEN2); + + val = ioread32(mmio_base + PCH_PP_CONTROL) & 0xfffffffe; + iowrite32(val, mmio_base + PCH_PP_CONTROL); + + timeout = jiffies + msecs_to_jiffies(IGD_OPERATION_TIMEOUT); + do { + val = ioread32(mmio_base + PCH_PP_STATUS); + if ((val & 0xb0000000) == 0) + goto reset_complete; + msleep(10); + } while (time_before(jiffies, timeout)); + pci_warn(dev, "timeout during reset\n"); + +reset_complete: + iowrite32(0x00000002, mmio_base + NSDE_PWR_STATE); + + pci_iounmap(dev, mmio_base); + return 0; +} + +/* Device-specific reset method for Chelsio T4-based adapters */ +static int reset_chelsio_generic_dev(struct pci_dev *dev, bool probe) +{ + u16 old_command; + u16 msix_flags; + + /* + * If this isn't a Chelsio T4-based device, return -ENOTTY indicating + * that we have no device-specific reset method. + */ + if ((dev->device & 0xf000) != 0x4000) + return -ENOTTY; + + /* + * If this is the "probe" phase, return 0 indicating that we can + * reset this device. + */ + if (probe) + return 0; + + /* + * T4 can wedge if there are DMAs in flight within the chip and Bus + * Master has been disabled. We need to have it on till the Function + * Level Reset completes. (BUS_MASTER is disabled in + * pci_reset_function()). + */ + pci_read_config_word(dev, PCI_COMMAND, &old_command); + pci_write_config_word(dev, PCI_COMMAND, + old_command | PCI_COMMAND_MASTER); + + /* + * Perform the actual device function reset, saving and restoring + * configuration information around the reset. + */ + pci_save_state(dev); + + /* + * T4 also suffers a Head-Of-Line blocking problem if MSI-X interrupts + * are disabled when an MSI-X interrupt message needs to be delivered. + * So we briefly re-enable MSI-X interrupts for the duration of the + * FLR. The pci_restore_state() below will restore the original + * MSI-X state. + */ + pci_read_config_word(dev, dev->msix_cap+PCI_MSIX_FLAGS, &msix_flags); + if ((msix_flags & PCI_MSIX_FLAGS_ENABLE) == 0) + pci_write_config_word(dev, dev->msix_cap+PCI_MSIX_FLAGS, + msix_flags | + PCI_MSIX_FLAGS_ENABLE | + PCI_MSIX_FLAGS_MASKALL); + + pcie_flr(dev); + + /* + * Restore the configuration information (BAR values, etc.) including + * the original PCI Configuration Space Command word, and return + * success. + */ + pci_restore_state(dev); + pci_write_config_word(dev, PCI_COMMAND, old_command); + return 0; +} + +#define PCI_DEVICE_ID_INTEL_82599_SFP_VF 0x10ed +#define PCI_DEVICE_ID_INTEL_IVB_M_VGA 0x0156 +#define PCI_DEVICE_ID_INTEL_IVB_M2_VGA 0x0166 + +/* + * The Samsung SM961/PM961 controller can sometimes enter a fatal state after + * FLR where config space reads from the device return -1. We seem to be + * able to avoid this condition if we disable the NVMe controller prior to + * FLR. This quirk is generic for any NVMe class device requiring similar + * assistance to quiesce the device prior to FLR. + * + * NVMe specification: https://nvmexpress.org/resources/specifications/ + * Revision 1.0e: + * Chapter 2: Required and optional PCI config registers + * Chapter 3: NVMe control registers + * Chapter 7.3: Reset behavior + */ +static int nvme_disable_and_flr(struct pci_dev *dev, bool probe) +{ + void __iomem *bar; + u16 cmd; + u32 cfg; + + if (dev->class != PCI_CLASS_STORAGE_EXPRESS || + pcie_reset_flr(dev, PCI_RESET_PROBE) || !pci_resource_start(dev, 0)) + return -ENOTTY; + + if (probe) + return 0; + + bar = pci_iomap(dev, 0, NVME_REG_CC + sizeof(cfg)); + if (!bar) + return -ENOTTY; + + pci_read_config_word(dev, PCI_COMMAND, &cmd); + pci_write_config_word(dev, PCI_COMMAND, cmd | PCI_COMMAND_MEMORY); + + cfg = readl(bar + NVME_REG_CC); + + /* Disable controller if enabled */ + if (cfg & NVME_CC_ENABLE) { + u32 cap = readl(bar + NVME_REG_CAP); + unsigned long timeout; + + /* + * Per nvme_disable_ctrl() skip shutdown notification as it + * could complete commands to the admin queue. We only intend + * to quiesce the device before reset. + */ + cfg &= ~(NVME_CC_SHN_MASK | NVME_CC_ENABLE); + + writel(cfg, bar + NVME_REG_CC); + + /* + * Some controllers require an additional delay here, see + * NVME_QUIRK_DELAY_BEFORE_CHK_RDY. None of those are yet + * supported by this quirk. + */ + + /* Cap register provides max timeout in 500ms increments */ + timeout = ((NVME_CAP_TIMEOUT(cap) + 1) * HZ / 2) + jiffies; + + for (;;) { + u32 status = readl(bar + NVME_REG_CSTS); + + /* Ready status becomes zero on disable complete */ + if (!(status & NVME_CSTS_RDY)) + break; + + msleep(100); + + if (time_after(jiffies, timeout)) { + pci_warn(dev, "Timeout waiting for NVMe ready status to clear after disable\n"); + break; + } + } + } + + pci_iounmap(dev, bar); + + pcie_flr(dev); + + return 0; +} + +/* + * Some NVMe controllers such as Intel DC P3700 and Solidigm P44 Pro will + * timeout waiting for ready status to change after NVMe enable if the driver + * starts interacting with the device too soon after FLR. A 250ms delay after + * FLR has heuristically proven to produce reliably working results for device + * assignment cases. + */ +static int delay_250ms_after_flr(struct pci_dev *dev, bool probe) +{ + if (probe) + return pcie_reset_flr(dev, PCI_RESET_PROBE); + + pcie_reset_flr(dev, PCI_RESET_DO_RESET); + + msleep(250); + + return 0; +} + +#define PCI_DEVICE_ID_HINIC_VF 0x375E +#define HINIC_VF_FLR_TYPE 0x1000 +#define HINIC_VF_FLR_CAP_BIT (1UL << 30) +#define HINIC_VF_OP 0xE80 +#define HINIC_VF_FLR_PROC_BIT (1UL << 18) +#define HINIC_OPERATION_TIMEOUT 15000 /* 15 seconds */ + +/* Device-specific reset method for Huawei Intelligent NIC virtual functions */ +static int reset_hinic_vf_dev(struct pci_dev *pdev, bool probe) +{ + unsigned long timeout; + void __iomem *bar; + u32 val; + + if (probe) + return 0; + + bar = pci_iomap(pdev, 0, 0); + if (!bar) + return -ENOTTY; + + /* Get and check firmware capabilities */ + val = ioread32be(bar + HINIC_VF_FLR_TYPE); + if (!(val & HINIC_VF_FLR_CAP_BIT)) { + pci_iounmap(pdev, bar); + return -ENOTTY; + } + + /* Set HINIC_VF_FLR_PROC_BIT for the start of FLR */ + val = ioread32be(bar + HINIC_VF_OP); + val = val | HINIC_VF_FLR_PROC_BIT; + iowrite32be(val, bar + HINIC_VF_OP); + + pcie_flr(pdev); + + /* + * The device must recapture its Bus and Device Numbers after FLR + * in order generate Completions. Issue a config write to let the + * device capture this information. + */ + pci_write_config_word(pdev, PCI_VENDOR_ID, 0); + + /* Firmware clears HINIC_VF_FLR_PROC_BIT when reset is complete */ + timeout = jiffies + msecs_to_jiffies(HINIC_OPERATION_TIMEOUT); + do { + val = ioread32be(bar + HINIC_VF_OP); + if (!(val & HINIC_VF_FLR_PROC_BIT)) + goto reset_complete; + msleep(20); + } while (time_before(jiffies, timeout)); + + val = ioread32be(bar + HINIC_VF_OP); + if (!(val & HINIC_VF_FLR_PROC_BIT)) + goto reset_complete; + + pci_warn(pdev, "Reset dev timeout, FLR ack reg: %#010x\n", val); + +reset_complete: + pci_iounmap(pdev, bar); + + return 0; +} + +static const struct pci_dev_reset_methods pci_dev_reset_methods[] = { + { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82599_SFP_VF, + reset_intel_82599_sfp_virtfn }, + { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IVB_M_VGA, + reset_ivb_igd }, + { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IVB_M2_VGA, + reset_ivb_igd }, + { PCI_VENDOR_ID_SAMSUNG, 0xa804, nvme_disable_and_flr }, + { PCI_VENDOR_ID_INTEL, 0x0953, delay_250ms_after_flr }, + { PCI_VENDOR_ID_INTEL, 0x0a54, delay_250ms_after_flr }, + { PCI_VENDOR_ID_SOLIDIGM, 0xf1ac, delay_250ms_after_flr }, + { PCI_VENDOR_ID_CHELSIO, PCI_ANY_ID, + reset_chelsio_generic_dev }, + { PCI_VENDOR_ID_HUAWEI, PCI_DEVICE_ID_HINIC_VF, + reset_hinic_vf_dev }, + { 0 } +}; + +/* + * These device-specific reset methods are here rather than in a driver + * because when a host assigns a device to a guest VM, the host may need + * to reset the device but probably doesn't have a driver for it. + */ +int pci_dev_specific_reset(struct pci_dev *dev, bool probe) +{ + const struct pci_dev_reset_methods *i; + + for (i = pci_dev_reset_methods; i->reset; i++) { + if ((i->vendor == dev->vendor || + i->vendor == (u16)PCI_ANY_ID) && + (i->device == dev->device || + i->device == (u16)PCI_ANY_ID)) + return i->reset(dev, probe); + } + + return -ENOTTY; +} + +static void quirk_dma_func0_alias(struct pci_dev *dev) +{ + if (PCI_FUNC(dev->devfn) != 0) + pci_add_dma_alias(dev, PCI_DEVFN(PCI_SLOT(dev->devfn), 0), 1); +} + +/* + * https://bugzilla.redhat.com/show_bug.cgi?id=605888 + * + * Some Ricoh devices use function 0 as the PCIe requester ID for DMA. + */ +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_RICOH, 0xe832, quirk_dma_func0_alias); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_RICOH, 0xe476, quirk_dma_func0_alias); + +static void quirk_dma_func1_alias(struct pci_dev *dev) +{ + if (PCI_FUNC(dev->devfn) != 1) + pci_add_dma_alias(dev, PCI_DEVFN(PCI_SLOT(dev->devfn), 1), 1); +} + +/* + * Marvell 88SE9123 uses function 1 as the requester ID for DMA. In some + * SKUs function 1 is present and is a legacy IDE controller, in other + * SKUs this function is not present, making this a ghost requester. + * https://bugzilla.kernel.org/show_bug.cgi?id=42679 + */ +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9120, + quirk_dma_func1_alias); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9123, + quirk_dma_func1_alias); +/* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c136 */ +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9125, + quirk_dma_func1_alias); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9128, + quirk_dma_func1_alias); +/* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c14 */ +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9130, + quirk_dma_func1_alias); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9170, + quirk_dma_func1_alias); +/* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c47 + c57 */ +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9172, + quirk_dma_func1_alias); +/* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c59 */ +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x917a, + quirk_dma_func1_alias); +/* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c78 */ +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9182, + quirk_dma_func1_alias); +/* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c134 */ +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9183, + quirk_dma_func1_alias); +/* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c46 */ +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x91a0, + quirk_dma_func1_alias); +/* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c135 */ +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9215, + quirk_dma_func1_alias); +/* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c127 */ +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9220, + quirk_dma_func1_alias); +/* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c49 */ +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9230, + quirk_dma_func1_alias); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9235, + quirk_dma_func1_alias); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TTI, 0x0642, + quirk_dma_func1_alias); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TTI, 0x0645, + quirk_dma_func1_alias); +/* https://bugs.gentoo.org/show_bug.cgi?id=497630 */ +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_JMICRON, + PCI_DEVICE_ID_JMICRON_JMB388_ESD, + quirk_dma_func1_alias); +/* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c117 */ +DECLARE_PCI_FIXUP_HEADER(0x1c28, /* Lite-On */ + 0x0122, /* Plextor M6E (Marvell 88SS9183)*/ + quirk_dma_func1_alias); + +/* + * Some devices DMA with the wrong devfn, not just the wrong function. + * quirk_fixed_dma_alias() uses this table to create fixed aliases, where + * the alias is "fixed" and independent of the device devfn. + * + * For example, the Adaptec 3405 is a PCIe card with an Intel 80333 I/O + * processor. To software, this appears as a PCIe-to-PCI/X bridge with a + * single device on the secondary bus. In reality, the single exposed + * device at 0e.0 is the Address Translation Unit (ATU) of the controller + * that provides a bridge to the internal bus of the I/O processor. The + * controller supports private devices, which can be hidden from PCI config + * space. In the case of the Adaptec 3405, a private device at 01.0 + * appears to be the DMA engine, which therefore needs to become a DMA + * alias for the device. + */ +static const struct pci_device_id fixed_dma_alias_tbl[] = { + { PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x0285, + PCI_VENDOR_ID_ADAPTEC2, 0x02bb), /* Adaptec 3405 */ + .driver_data = PCI_DEVFN(1, 0) }, + { PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x0285, + PCI_VENDOR_ID_ADAPTEC2, 0x02bc), /* Adaptec 3805 */ + .driver_data = PCI_DEVFN(1, 0) }, + { 0 } +}; + +static void quirk_fixed_dma_alias(struct pci_dev *dev) +{ + const struct pci_device_id *id; + + id = pci_match_id(fixed_dma_alias_tbl, dev); + if (id) + pci_add_dma_alias(dev, id->driver_data, 1); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ADAPTEC2, 0x0285, quirk_fixed_dma_alias); + +/* + * A few PCIe-to-PCI bridges fail to expose a PCIe capability, resulting in + * using the wrong DMA alias for the device. Some of these devices can be + * used as either forward or reverse bridges, so we need to test whether the + * device is operating in the correct mode. We could probably apply this + * quirk to PCI_ANY_ID, but for now we'll just use known offenders. The test + * is for a non-root, non-PCIe bridge where the upstream device is PCIe and + * is not a PCIe-to-PCI bridge, then @pdev is actually a PCIe-to-PCI bridge. + */ +static void quirk_use_pcie_bridge_dma_alias(struct pci_dev *pdev) +{ + if (!pci_is_root_bus(pdev->bus) && + pdev->hdr_type == PCI_HEADER_TYPE_BRIDGE && + !pci_is_pcie(pdev) && pci_is_pcie(pdev->bus->self) && + pci_pcie_type(pdev->bus->self) != PCI_EXP_TYPE_PCI_BRIDGE) + pdev->dev_flags |= PCI_DEV_FLAG_PCIE_BRIDGE_ALIAS; +} +/* ASM1083/1085, https://bugzilla.kernel.org/show_bug.cgi?id=44881#c46 */ +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ASMEDIA, 0x1080, + quirk_use_pcie_bridge_dma_alias); +/* Tundra 8113, https://bugzilla.kernel.org/show_bug.cgi?id=44881#c43 */ +DECLARE_PCI_FIXUP_HEADER(0x10e3, 0x8113, quirk_use_pcie_bridge_dma_alias); +/* ITE 8892, https://bugzilla.kernel.org/show_bug.cgi?id=73551 */ +DECLARE_PCI_FIXUP_HEADER(0x1283, 0x8892, quirk_use_pcie_bridge_dma_alias); +/* ITE 8893 has the same problem as the 8892 */ +DECLARE_PCI_FIXUP_HEADER(0x1283, 0x8893, quirk_use_pcie_bridge_dma_alias); +/* Intel 82801, https://bugzilla.kernel.org/show_bug.cgi?id=44881#c49 */ +DECLARE_PCI_FIXUP_HEADER(0x8086, 0x244e, quirk_use_pcie_bridge_dma_alias); + +/* + * MIC x200 NTB forwards PCIe traffic using multiple alien RIDs. They have to + * be added as aliases to the DMA device in order to allow buffer access + * when IOMMU is enabled. Following devfns have to match RIT-LUT table + * programmed in the EEPROM. + */ +static void quirk_mic_x200_dma_alias(struct pci_dev *pdev) +{ + pci_add_dma_alias(pdev, PCI_DEVFN(0x10, 0x0), 1); + pci_add_dma_alias(pdev, PCI_DEVFN(0x11, 0x0), 1); + pci_add_dma_alias(pdev, PCI_DEVFN(0x12, 0x3), 1); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x2260, quirk_mic_x200_dma_alias); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x2264, quirk_mic_x200_dma_alias); + +/* + * Intel Visual Compute Accelerator (VCA) is a family of PCIe add-in devices + * exposing computational units via Non Transparent Bridges (NTB, PEX 87xx). + * + * Similarly to MIC x200, we need to add DMA aliases to allow buffer access + * when IOMMU is enabled. These aliases allow computational unit access to + * host memory. These aliases mark the whole VCA device as one IOMMU + * group. + * + * All possible slot numbers (0x20) are used, since we are unable to tell + * what slot is used on other side. This quirk is intended for both host + * and computational unit sides. The VCA devices have up to five functions + * (four for DMA channels and one additional). + */ +static void quirk_pex_vca_alias(struct pci_dev *pdev) +{ + const unsigned int num_pci_slots = 0x20; + unsigned int slot; + + for (slot = 0; slot < num_pci_slots; slot++) + pci_add_dma_alias(pdev, PCI_DEVFN(slot, 0x0), 5); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x2954, quirk_pex_vca_alias); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x2955, quirk_pex_vca_alias); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x2956, quirk_pex_vca_alias); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x2958, quirk_pex_vca_alias); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x2959, quirk_pex_vca_alias); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x295A, quirk_pex_vca_alias); + +/* + * The IOMMU and interrupt controller on Broadcom Vulcan/Cavium ThunderX2 are + * associated not at the root bus, but at a bridge below. This quirk avoids + * generating invalid DMA aliases. + */ +static void quirk_bridge_cavm_thrx2_pcie_root(struct pci_dev *pdev) +{ + pdev->dev_flags |= PCI_DEV_FLAGS_BRIDGE_XLATE_ROOT; +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_BROADCOM, 0x9000, + quirk_bridge_cavm_thrx2_pcie_root); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_BROADCOM, 0x9084, + quirk_bridge_cavm_thrx2_pcie_root); + +/* + * Intersil/Techwell TW686[4589]-based video capture cards have an empty (zero) + * class code. Fix it. + */ +static void quirk_tw686x_class(struct pci_dev *pdev) +{ + u32 class = pdev->class; + + /* Use "Multimedia controller" class */ + pdev->class = (PCI_CLASS_MULTIMEDIA_OTHER << 8) | 0x01; + pci_info(pdev, "TW686x PCI class overridden (%#08x -> %#08x)\n", + class, pdev->class); +} +DECLARE_PCI_FIXUP_CLASS_EARLY(0x1797, 0x6864, PCI_CLASS_NOT_DEFINED, 8, + quirk_tw686x_class); +DECLARE_PCI_FIXUP_CLASS_EARLY(0x1797, 0x6865, PCI_CLASS_NOT_DEFINED, 8, + quirk_tw686x_class); +DECLARE_PCI_FIXUP_CLASS_EARLY(0x1797, 0x6868, PCI_CLASS_NOT_DEFINED, 8, + quirk_tw686x_class); +DECLARE_PCI_FIXUP_CLASS_EARLY(0x1797, 0x6869, PCI_CLASS_NOT_DEFINED, 8, + quirk_tw686x_class); + +/* + * Some devices have problems with Transaction Layer Packets with the Relaxed + * Ordering Attribute set. Such devices should mark themselves and other + * device drivers should check before sending TLPs with RO set. + */ +static void quirk_relaxedordering_disable(struct pci_dev *dev) +{ + dev->dev_flags |= PCI_DEV_FLAGS_NO_RELAXED_ORDERING; + pci_info(dev, "Disable Relaxed Ordering Attributes to avoid PCIe Completion erratum\n"); +} + +/* + * Intel Xeon processors based on Broadwell/Haswell microarchitecture Root + * Complex have a Flow Control Credit issue which can cause performance + * problems with Upstream Transaction Layer Packets with Relaxed Ordering set. + */ +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f01, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f02, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f03, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f04, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f05, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f06, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f07, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f08, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f09, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f0a, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f0b, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f0c, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f0d, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f0e, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f01, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f02, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f03, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f04, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f05, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f06, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f07, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f08, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f09, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f0a, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f0b, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f0c, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f0d, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f0e, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); + +/* + * The AMD ARM A1100 (aka "SEATTLE") SoC has a bug in its PCIe Root Complex + * where Upstream Transaction Layer Packets with the Relaxed Ordering + * Attribute clear are allowed to bypass earlier TLPs with Relaxed Ordering + * set. This is a violation of the PCIe 3.0 Transaction Ordering Rules + * outlined in Section 2.4.1 (PCI Express(r) Base Specification Revision 3.0 + * November 10, 2010). As a result, on this platform we can't use Relaxed + * Ordering for Upstream TLPs. + */ +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_AMD, 0x1a00, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_AMD, 0x1a01, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); +DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_AMD, 0x1a02, PCI_CLASS_NOT_DEFINED, 8, + quirk_relaxedordering_disable); + +/* + * Per PCIe r3.0, sec 2.2.9, "Completion headers must supply the same + * values for the Attribute as were supplied in the header of the + * corresponding Request, except as explicitly allowed when IDO is used." + * + * If a non-compliant device generates a completion with a different + * attribute than the request, the receiver may accept it (which itself + * seems non-compliant based on sec 2.3.2), or it may handle it as a + * Malformed TLP or an Unexpected Completion, which will probably lead to a + * device access timeout. + * + * If the non-compliant device generates completions with zero attributes + * (instead of copying the attributes from the request), we can work around + * this by disabling the "Relaxed Ordering" and "No Snoop" attributes in + * upstream devices so they always generate requests with zero attributes. + * + * This affects other devices under the same Root Port, but since these + * attributes are performance hints, there should be no functional problem. + * + * Note that Configuration Space accesses are never supposed to have TLP + * Attributes, so we're safe waiting till after any Configuration Space + * accesses to do the Root Port fixup. + */ +static void quirk_disable_root_port_attributes(struct pci_dev *pdev) +{ + struct pci_dev *root_port = pcie_find_root_port(pdev); + + if (!root_port) { + pci_warn(pdev, "PCIe Completion erratum may cause device errors\n"); + return; + } + + pci_info(root_port, "Disabling No Snoop/Relaxed Ordering Attributes to avoid PCIe Completion erratum in %s\n", + dev_name(&pdev->dev)); + pcie_capability_clear_and_set_word(root_port, PCI_EXP_DEVCTL, + PCI_EXP_DEVCTL_RELAX_EN | + PCI_EXP_DEVCTL_NOSNOOP_EN, 0); +} + +/* + * The Chelsio T5 chip fails to copy TLP Attributes from a Request to the + * Completion it generates. + */ +static void quirk_chelsio_T5_disable_root_port_attributes(struct pci_dev *pdev) +{ + /* + * This mask/compare operation selects for Physical Function 4 on a + * T5. We only need to fix up the Root Port once for any of the + * PFs. PF[0..3] have PCI Device IDs of 0x50xx, but PF4 is uniquely + * 0x54xx so we use that one. + */ + if ((pdev->device & 0xff00) == 0x5400) + quirk_disable_root_port_attributes(pdev); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_CHELSIO, PCI_ANY_ID, + quirk_chelsio_T5_disable_root_port_attributes); + +/* + * pci_acs_ctrl_enabled - compare desired ACS controls with those provided + * by a device + * @acs_ctrl_req: Bitmask of desired ACS controls + * @acs_ctrl_ena: Bitmask of ACS controls enabled or provided implicitly by + * the hardware design + * + * Return 1 if all ACS controls in the @acs_ctrl_req bitmask are included + * in @acs_ctrl_ena, i.e., the device provides all the access controls the + * caller desires. Return 0 otherwise. + */ +static int pci_acs_ctrl_enabled(u16 acs_ctrl_req, u16 acs_ctrl_ena) +{ + if ((acs_ctrl_req & acs_ctrl_ena) == acs_ctrl_req) + return 1; + return 0; +} + +/* + * AMD has indicated that the devices below do not support peer-to-peer + * in any system where they are found in the southbridge with an AMD + * IOMMU in the system. Multifunction devices that do not support + * peer-to-peer between functions can claim to support a subset of ACS. + * Such devices effectively enable request redirect (RR) and completion + * redirect (CR) since all transactions are redirected to the upstream + * root complex. + * + * https://lore.kernel.org/r/201207111426.q6BEQTbh002928@mail.maya.org/ + * https://lore.kernel.org/r/20120711165854.GM25282@amd.com/ + * https://lore.kernel.org/r/20121005130857.GX4009@amd.com/ + * + * 1002:4385 SBx00 SMBus Controller + * 1002:439c SB7x0/SB8x0/SB9x0 IDE Controller + * 1002:4383 SBx00 Azalia (Intel HDA) + * 1002:439d SB7x0/SB8x0/SB9x0 LPC host controller + * 1002:4384 SBx00 PCI to PCI Bridge + * 1002:4399 SB7x0/SB8x0/SB9x0 USB OHCI2 Controller + * + * https://bugzilla.kernel.org/show_bug.cgi?id=81841#c15 + * + * 1022:780f [AMD] FCH PCI Bridge + * 1022:7809 [AMD] FCH USB OHCI Controller + */ +static int pci_quirk_amd_sb_acs(struct pci_dev *dev, u16 acs_flags) +{ +#ifdef CONFIG_ACPI + struct acpi_table_header *header = NULL; + acpi_status status; + + /* Targeting multifunction devices on the SB (appears on root bus) */ + if (!dev->multifunction || !pci_is_root_bus(dev->bus)) + return -ENODEV; + + /* The IVRS table describes the AMD IOMMU */ + status = acpi_get_table("IVRS", 0, &header); + if (ACPI_FAILURE(status)) + return -ENODEV; + + acpi_put_table(header); + + /* Filter out flags not applicable to multifunction */ + acs_flags &= (PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_EC | PCI_ACS_DT); + + return pci_acs_ctrl_enabled(acs_flags, PCI_ACS_RR | PCI_ACS_CR); +#else + return -ENODEV; +#endif +} + +static bool pci_quirk_cavium_acs_match(struct pci_dev *dev) +{ + if (!pci_is_pcie(dev) || pci_pcie_type(dev) != PCI_EXP_TYPE_ROOT_PORT) + return false; + + switch (dev->device) { + /* + * Effectively selects all downstream ports for whole ThunderX1 + * (which represents 8 SoCs). + */ + case 0xa000 ... 0xa7ff: /* ThunderX1 */ + case 0xaf84: /* ThunderX2 */ + case 0xb884: /* ThunderX3 */ + return true; + default: + return false; + } +} + +static int pci_quirk_cavium_acs(struct pci_dev *dev, u16 acs_flags) +{ + if (!pci_quirk_cavium_acs_match(dev)) + return -ENOTTY; + + /* + * Cavium Root Ports don't advertise an ACS capability. However, + * the RTL internally implements similar protection as if ACS had + * Source Validation, Request Redirection, Completion Redirection, + * and Upstream Forwarding features enabled. Assert that the + * hardware implements and enables equivalent ACS functionality for + * these flags. + */ + return pci_acs_ctrl_enabled(acs_flags, + PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF); +} + +static int pci_quirk_xgene_acs(struct pci_dev *dev, u16 acs_flags) +{ + /* + * X-Gene Root Ports matching this quirk do not allow peer-to-peer + * transactions with others, allowing masking out these bits as if they + * were unimplemented in the ACS capability. + */ + return pci_acs_ctrl_enabled(acs_flags, + PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF); +} + +/* + * Many Zhaoxin Root Ports and Switch Downstream Ports have no ACS capability. + * But the implementation could block peer-to-peer transactions between them + * and provide ACS-like functionality. + */ +static int pci_quirk_zhaoxin_pcie_ports_acs(struct pci_dev *dev, u16 acs_flags) +{ + if (!pci_is_pcie(dev) || + ((pci_pcie_type(dev) != PCI_EXP_TYPE_ROOT_PORT) && + (pci_pcie_type(dev) != PCI_EXP_TYPE_DOWNSTREAM))) + return -ENOTTY; + + /* + * Future Zhaoxin Root Ports and Switch Downstream Ports will + * implement ACS capability in accordance with the PCIe Spec. + */ + switch (dev->device) { + case 0x0710 ... 0x071e: + case 0x0721: + case 0x0723 ... 0x0752: + return pci_acs_ctrl_enabled(acs_flags, + PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF); + } + + return false; +} + +/* + * Many Intel PCH Root Ports do provide ACS-like features to disable peer + * transactions and validate bus numbers in requests, but do not provide an + * actual PCIe ACS capability. This is the list of device IDs known to fall + * into that category as provided by Intel in Red Hat bugzilla 1037684. + */ +static const u16 pci_quirk_intel_pch_acs_ids[] = { + /* Ibexpeak PCH */ + 0x3b42, 0x3b43, 0x3b44, 0x3b45, 0x3b46, 0x3b47, 0x3b48, 0x3b49, + 0x3b4a, 0x3b4b, 0x3b4c, 0x3b4d, 0x3b4e, 0x3b4f, 0x3b50, 0x3b51, + /* Cougarpoint PCH */ + 0x1c10, 0x1c11, 0x1c12, 0x1c13, 0x1c14, 0x1c15, 0x1c16, 0x1c17, + 0x1c18, 0x1c19, 0x1c1a, 0x1c1b, 0x1c1c, 0x1c1d, 0x1c1e, 0x1c1f, + /* Pantherpoint PCH */ + 0x1e10, 0x1e11, 0x1e12, 0x1e13, 0x1e14, 0x1e15, 0x1e16, 0x1e17, + 0x1e18, 0x1e19, 0x1e1a, 0x1e1b, 0x1e1c, 0x1e1d, 0x1e1e, 0x1e1f, + /* Lynxpoint-H PCH */ + 0x8c10, 0x8c11, 0x8c12, 0x8c13, 0x8c14, 0x8c15, 0x8c16, 0x8c17, + 0x8c18, 0x8c19, 0x8c1a, 0x8c1b, 0x8c1c, 0x8c1d, 0x8c1e, 0x8c1f, + /* Lynxpoint-LP PCH */ + 0x9c10, 0x9c11, 0x9c12, 0x9c13, 0x9c14, 0x9c15, 0x9c16, 0x9c17, + 0x9c18, 0x9c19, 0x9c1a, 0x9c1b, + /* Wildcat PCH */ + 0x9c90, 0x9c91, 0x9c92, 0x9c93, 0x9c94, 0x9c95, 0x9c96, 0x9c97, + 0x9c98, 0x9c99, 0x9c9a, 0x9c9b, + /* Patsburg (X79) PCH */ + 0x1d10, 0x1d12, 0x1d14, 0x1d16, 0x1d18, 0x1d1a, 0x1d1c, 0x1d1e, + /* Wellsburg (X99) PCH */ + 0x8d10, 0x8d11, 0x8d12, 0x8d13, 0x8d14, 0x8d15, 0x8d16, 0x8d17, + 0x8d18, 0x8d19, 0x8d1a, 0x8d1b, 0x8d1c, 0x8d1d, 0x8d1e, + /* Lynx Point (9 series) PCH */ + 0x8c90, 0x8c92, 0x8c94, 0x8c96, 0x8c98, 0x8c9a, 0x8c9c, 0x8c9e, +}; + +static bool pci_quirk_intel_pch_acs_match(struct pci_dev *dev) +{ + int i; + + /* Filter out a few obvious non-matches first */ + if (!pci_is_pcie(dev) || pci_pcie_type(dev) != PCI_EXP_TYPE_ROOT_PORT) + return false; + + for (i = 0; i < ARRAY_SIZE(pci_quirk_intel_pch_acs_ids); i++) + if (pci_quirk_intel_pch_acs_ids[i] == dev->device) + return true; + + return false; +} + +static int pci_quirk_intel_pch_acs(struct pci_dev *dev, u16 acs_flags) +{ + if (!pci_quirk_intel_pch_acs_match(dev)) + return -ENOTTY; + + if (dev->dev_flags & PCI_DEV_FLAGS_ACS_ENABLED_QUIRK) + return pci_acs_ctrl_enabled(acs_flags, + PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF); + + return pci_acs_ctrl_enabled(acs_flags, 0); +} + +/* + * These QCOM Root Ports do provide ACS-like features to disable peer + * transactions and validate bus numbers in requests, but do not provide an + * actual PCIe ACS capability. Hardware supports source validation but it + * will report the issue as Completer Abort instead of ACS Violation. + * Hardware doesn't support peer-to-peer and each Root Port is a Root + * Complex with unique segment numbers. It is not possible for one Root + * Port to pass traffic to another Root Port. All PCIe transactions are + * terminated inside the Root Port. + */ +static int pci_quirk_qcom_rp_acs(struct pci_dev *dev, u16 acs_flags) +{ + return pci_acs_ctrl_enabled(acs_flags, + PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF); +} + +/* + * Each of these NXP Root Ports is in a Root Complex with a unique segment + * number and does provide isolation features to disable peer transactions + * and validate bus numbers in requests, but does not provide an ACS + * capability. + */ +static int pci_quirk_nxp_rp_acs(struct pci_dev *dev, u16 acs_flags) +{ + return pci_acs_ctrl_enabled(acs_flags, + PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF); +} + +static int pci_quirk_al_acs(struct pci_dev *dev, u16 acs_flags) +{ + if (pci_pcie_type(dev) != PCI_EXP_TYPE_ROOT_PORT) + return -ENOTTY; + + /* + * Amazon's Annapurna Labs root ports don't include an ACS capability, + * but do include ACS-like functionality. The hardware doesn't support + * peer-to-peer transactions via the root port and each has a unique + * segment number. + * + * Additionally, the root ports cannot send traffic to each other. + */ + acs_flags &= ~(PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF); + + return acs_flags ? 0 : 1; +} + +/* + * Sunrise Point PCH root ports implement ACS, but unfortunately as shown in + * the datasheet (Intel 100 Series Chipset Family PCH Datasheet, Vol. 2, + * 12.1.46, 12.1.47)[1] this chipset uses dwords for the ACS capability and + * control registers whereas the PCIe spec packs them into words (Rev 3.0, + * 7.16 ACS Extended Capability). The bit definitions are correct, but the + * control register is at offset 8 instead of 6 and we should probably use + * dword accesses to them. This applies to the following PCI Device IDs, as + * found in volume 1 of the datasheet[2]: + * + * 0xa110-0xa11f Sunrise Point-H PCI Express Root Port #{0-16} + * 0xa167-0xa16a Sunrise Point-H PCI Express Root Port #{17-20} + * + * N.B. This doesn't fix what lspci shows. + * + * The 100 series chipset specification update includes this as errata #23[3]. + * + * The 200 series chipset (Union Point) has the same bug according to the + * specification update (Intel 200 Series Chipset Family Platform Controller + * Hub, Specification Update, January 2017, Revision 001, Document# 335194-001, + * Errata 22)[4]. Per the datasheet[5], root port PCI Device IDs for this + * chipset include: + * + * 0xa290-0xa29f PCI Express Root port #{0-16} + * 0xa2e7-0xa2ee PCI Express Root port #{17-24} + * + * Mobile chipsets are also affected, 7th & 8th Generation + * Specification update confirms ACS errata 22, status no fix: (7th Generation + * Intel Processor Family I/O for U/Y Platforms and 8th Generation Intel + * Processor Family I/O for U Quad Core Platforms Specification Update, + * August 2017, Revision 002, Document#: 334660-002)[6] + * Device IDs from I/O datasheet: (7th Generation Intel Processor Family I/O + * for U/Y Platforms and 8th Generation Intel ® Processor Family I/O for U + * Quad Core Platforms, Vol 1 of 2, August 2017, Document#: 334658-003)[7] + * + * 0x9d10-0x9d1b PCI Express Root port #{1-12} + * + * [1] https://www.intel.com/content/www/us/en/chipsets/100-series-chipset-datasheet-vol-2.html + * [2] https://www.intel.com/content/www/us/en/chipsets/100-series-chipset-datasheet-vol-1.html + * [3] https://www.intel.com/content/www/us/en/chipsets/100-series-chipset-spec-update.html + * [4] https://www.intel.com/content/www/us/en/chipsets/200-series-chipset-pch-spec-update.html + * [5] https://www.intel.com/content/www/us/en/chipsets/200-series-chipset-pch-datasheet-vol-1.html + * [6] https://www.intel.com/content/www/us/en/processors/core/7th-gen-core-family-mobile-u-y-processor-lines-i-o-spec-update.html + * [7] https://www.intel.com/content/www/us/en/processors/core/7th-gen-core-family-mobile-u-y-processor-lines-i-o-datasheet-vol-1.html + */ +static bool pci_quirk_intel_spt_pch_acs_match(struct pci_dev *dev) +{ + if (!pci_is_pcie(dev) || pci_pcie_type(dev) != PCI_EXP_TYPE_ROOT_PORT) + return false; + + switch (dev->device) { + case 0xa110 ... 0xa11f: case 0xa167 ... 0xa16a: /* Sunrise Point */ + case 0xa290 ... 0xa29f: case 0xa2e7 ... 0xa2ee: /* Union Point */ + case 0x9d10 ... 0x9d1b: /* 7th & 8th Gen Mobile */ + return true; + } + + return false; +} + +#define INTEL_SPT_ACS_CTRL (PCI_ACS_CAP + 4) + +static int pci_quirk_intel_spt_pch_acs(struct pci_dev *dev, u16 acs_flags) +{ + int pos; + u32 cap, ctrl; + + if (!pci_quirk_intel_spt_pch_acs_match(dev)) + return -ENOTTY; + + pos = dev->acs_cap; + if (!pos) + return -ENOTTY; + + /* see pci_acs_flags_enabled() */ + pci_read_config_dword(dev, pos + PCI_ACS_CAP, &cap); + acs_flags &= (cap | PCI_ACS_EC); + + pci_read_config_dword(dev, pos + INTEL_SPT_ACS_CTRL, &ctrl); + + return pci_acs_ctrl_enabled(acs_flags, ctrl); +} + +static int pci_quirk_mf_endpoint_acs(struct pci_dev *dev, u16 acs_flags) +{ + /* + * SV, TB, and UF are not relevant to multifunction endpoints. + * + * Multifunction devices are only required to implement RR, CR, and DT + * in their ACS capability if they support peer-to-peer transactions. + * Devices matching this quirk have been verified by the vendor to not + * perform peer-to-peer with other functions, allowing us to mask out + * these bits as if they were unimplemented in the ACS capability. + */ + return pci_acs_ctrl_enabled(acs_flags, + PCI_ACS_SV | PCI_ACS_TB | PCI_ACS_RR | + PCI_ACS_CR | PCI_ACS_UF | PCI_ACS_DT); +} + +static int pci_quirk_rciep_acs(struct pci_dev *dev, u16 acs_flags) +{ + /* + * Intel RCiEP's are required to allow p2p only on translated + * addresses. Refer to Intel VT-d specification, r3.1, sec 3.16, + * "Root-Complex Peer to Peer Considerations". + */ + if (pci_pcie_type(dev) != PCI_EXP_TYPE_RC_END) + return -ENOTTY; + + return pci_acs_ctrl_enabled(acs_flags, + PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF); +} + +static int pci_quirk_brcm_acs(struct pci_dev *dev, u16 acs_flags) +{ + /* + * iProc PAXB Root Ports don't advertise an ACS capability, but + * they do not allow peer-to-peer transactions between Root Ports. + * Allow each Root Port to be in a separate IOMMU group by masking + * SV/RR/CR/UF bits. + */ + return pci_acs_ctrl_enabled(acs_flags, + PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF); +} + +/* + * Wangxun 10G/1G NICs have no ACS capability, and on multi-function + * devices, peer-to-peer transactions are not be used between the functions. + * So add an ACS quirk for below devices to isolate functions. + * SFxxx 1G NICs(em). + * RP1000/RP2000 10G NICs(sp). + */ +static int pci_quirk_wangxun_nic_acs(struct pci_dev *dev, u16 acs_flags) +{ + switch (dev->device) { + case 0x0100 ... 0x010F: + case 0x1001: + case 0x2001: + return pci_acs_ctrl_enabled(acs_flags, + PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF); + } + + return false; +} + +static const struct pci_dev_acs_enabled { + u16 vendor; + u16 device; + int (*acs_enabled)(struct pci_dev *dev, u16 acs_flags); +} pci_dev_acs_enabled[] = { + { PCI_VENDOR_ID_ATI, 0x4385, pci_quirk_amd_sb_acs }, + { PCI_VENDOR_ID_ATI, 0x439c, pci_quirk_amd_sb_acs }, + { PCI_VENDOR_ID_ATI, 0x4383, pci_quirk_amd_sb_acs }, + { PCI_VENDOR_ID_ATI, 0x439d, pci_quirk_amd_sb_acs }, + { PCI_VENDOR_ID_ATI, 0x4384, pci_quirk_amd_sb_acs }, + { PCI_VENDOR_ID_ATI, 0x4399, pci_quirk_amd_sb_acs }, + { PCI_VENDOR_ID_AMD, 0x780f, pci_quirk_amd_sb_acs }, + { PCI_VENDOR_ID_AMD, 0x7809, pci_quirk_amd_sb_acs }, + { PCI_VENDOR_ID_SOLARFLARE, 0x0903, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_SOLARFLARE, 0x0923, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_SOLARFLARE, 0x0A03, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x10C6, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x10DB, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x10DD, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x10E1, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x10F1, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x10F7, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x10F8, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x10F9, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x10FA, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x10FB, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x10FC, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x1507, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x1514, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x151C, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x1529, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x152A, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x154D, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x154F, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x1551, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x1558, pci_quirk_mf_endpoint_acs }, + /* 82580 */ + { PCI_VENDOR_ID_INTEL, 0x1509, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x150E, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x150F, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x1510, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x1511, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x1516, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x1527, pci_quirk_mf_endpoint_acs }, + /* 82576 */ + { PCI_VENDOR_ID_INTEL, 0x10C9, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x10E6, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x10E7, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x10E8, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x150A, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x150D, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x1518, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x1526, pci_quirk_mf_endpoint_acs }, + /* 82575 */ + { PCI_VENDOR_ID_INTEL, 0x10A7, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x10A9, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x10D6, pci_quirk_mf_endpoint_acs }, + /* I350 */ + { PCI_VENDOR_ID_INTEL, 0x1521, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x1522, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x1523, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x1524, pci_quirk_mf_endpoint_acs }, + /* 82571 (Quads omitted due to non-ACS switch) */ + { PCI_VENDOR_ID_INTEL, 0x105E, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x105F, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x1060, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x10D9, pci_quirk_mf_endpoint_acs }, + /* I219 */ + { PCI_VENDOR_ID_INTEL, 0x15b7, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, 0x15b8, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_INTEL, PCI_ANY_ID, pci_quirk_rciep_acs }, + /* QCOM QDF2xxx root ports */ + { PCI_VENDOR_ID_QCOM, 0x0400, pci_quirk_qcom_rp_acs }, + { PCI_VENDOR_ID_QCOM, 0x0401, pci_quirk_qcom_rp_acs }, + /* HXT SD4800 root ports. The ACS design is same as QCOM QDF2xxx */ + { PCI_VENDOR_ID_HXT, 0x0401, pci_quirk_qcom_rp_acs }, + /* Intel PCH root ports */ + { PCI_VENDOR_ID_INTEL, PCI_ANY_ID, pci_quirk_intel_pch_acs }, + { PCI_VENDOR_ID_INTEL, PCI_ANY_ID, pci_quirk_intel_spt_pch_acs }, + { 0x19a2, 0x710, pci_quirk_mf_endpoint_acs }, /* Emulex BE3-R */ + { 0x10df, 0x720, pci_quirk_mf_endpoint_acs }, /* Emulex Skyhawk-R */ + /* Cavium ThunderX */ + { PCI_VENDOR_ID_CAVIUM, PCI_ANY_ID, pci_quirk_cavium_acs }, + /* Cavium multi-function devices */ + { PCI_VENDOR_ID_CAVIUM, 0xA026, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_CAVIUM, 0xA059, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_CAVIUM, 0xA060, pci_quirk_mf_endpoint_acs }, + /* APM X-Gene */ + { PCI_VENDOR_ID_AMCC, 0xE004, pci_quirk_xgene_acs }, + /* Ampere Computing */ + { PCI_VENDOR_ID_AMPERE, 0xE005, pci_quirk_xgene_acs }, + { PCI_VENDOR_ID_AMPERE, 0xE006, pci_quirk_xgene_acs }, + { PCI_VENDOR_ID_AMPERE, 0xE007, pci_quirk_xgene_acs }, + { PCI_VENDOR_ID_AMPERE, 0xE008, pci_quirk_xgene_acs }, + { PCI_VENDOR_ID_AMPERE, 0xE009, pci_quirk_xgene_acs }, + { PCI_VENDOR_ID_AMPERE, 0xE00A, pci_quirk_xgene_acs }, + { PCI_VENDOR_ID_AMPERE, 0xE00B, pci_quirk_xgene_acs }, + { PCI_VENDOR_ID_AMPERE, 0xE00C, pci_quirk_xgene_acs }, + /* Broadcom multi-function device */ + { PCI_VENDOR_ID_BROADCOM, 0x16D7, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_BROADCOM, 0x1750, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_BROADCOM, 0x1751, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_BROADCOM, 0x1752, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_BROADCOM, 0xD714, pci_quirk_brcm_acs }, + /* Amazon Annapurna Labs */ + { PCI_VENDOR_ID_AMAZON_ANNAPURNA_LABS, 0x0031, pci_quirk_al_acs }, + /* Zhaoxin multi-function devices */ + { PCI_VENDOR_ID_ZHAOXIN, 0x3038, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_ZHAOXIN, 0x3104, pci_quirk_mf_endpoint_acs }, + { PCI_VENDOR_ID_ZHAOXIN, 0x9083, pci_quirk_mf_endpoint_acs }, + /* NXP root ports, xx=16, 12, or 08 cores */ + /* LX2xx0A : without security features + CAN-FD */ + { PCI_VENDOR_ID_NXP, 0x8d81, pci_quirk_nxp_rp_acs }, + { PCI_VENDOR_ID_NXP, 0x8da1, pci_quirk_nxp_rp_acs }, + { PCI_VENDOR_ID_NXP, 0x8d83, pci_quirk_nxp_rp_acs }, + /* LX2xx0C : security features + CAN-FD */ + { PCI_VENDOR_ID_NXP, 0x8d80, pci_quirk_nxp_rp_acs }, + { PCI_VENDOR_ID_NXP, 0x8da0, pci_quirk_nxp_rp_acs }, + { PCI_VENDOR_ID_NXP, 0x8d82, pci_quirk_nxp_rp_acs }, + /* LX2xx0E : security features + CAN */ + { PCI_VENDOR_ID_NXP, 0x8d90, pci_quirk_nxp_rp_acs }, + { PCI_VENDOR_ID_NXP, 0x8db0, pci_quirk_nxp_rp_acs }, + { PCI_VENDOR_ID_NXP, 0x8d92, pci_quirk_nxp_rp_acs }, + /* LX2xx0N : without security features + CAN */ + { PCI_VENDOR_ID_NXP, 0x8d91, pci_quirk_nxp_rp_acs }, + { PCI_VENDOR_ID_NXP, 0x8db1, pci_quirk_nxp_rp_acs }, + { PCI_VENDOR_ID_NXP, 0x8d93, pci_quirk_nxp_rp_acs }, + /* LX2xx2A : without security features + CAN-FD */ + { PCI_VENDOR_ID_NXP, 0x8d89, pci_quirk_nxp_rp_acs }, + { PCI_VENDOR_ID_NXP, 0x8da9, pci_quirk_nxp_rp_acs }, + { PCI_VENDOR_ID_NXP, 0x8d8b, pci_quirk_nxp_rp_acs }, + /* LX2xx2C : security features + CAN-FD */ + { PCI_VENDOR_ID_NXP, 0x8d88, pci_quirk_nxp_rp_acs }, + { PCI_VENDOR_ID_NXP, 0x8da8, pci_quirk_nxp_rp_acs }, + { PCI_VENDOR_ID_NXP, 0x8d8a, pci_quirk_nxp_rp_acs }, + /* LX2xx2E : security features + CAN */ + { PCI_VENDOR_ID_NXP, 0x8d98, pci_quirk_nxp_rp_acs }, + { PCI_VENDOR_ID_NXP, 0x8db8, pci_quirk_nxp_rp_acs }, + { PCI_VENDOR_ID_NXP, 0x8d9a, pci_quirk_nxp_rp_acs }, + /* LX2xx2N : without security features + CAN */ + { PCI_VENDOR_ID_NXP, 0x8d99, pci_quirk_nxp_rp_acs }, + { PCI_VENDOR_ID_NXP, 0x8db9, pci_quirk_nxp_rp_acs }, + { PCI_VENDOR_ID_NXP, 0x8d9b, pci_quirk_nxp_rp_acs }, + /* Zhaoxin Root/Downstream Ports */ + { PCI_VENDOR_ID_ZHAOXIN, PCI_ANY_ID, pci_quirk_zhaoxin_pcie_ports_acs }, + /* Wangxun nics */ + { PCI_VENDOR_ID_WANGXUN, PCI_ANY_ID, pci_quirk_wangxun_nic_acs }, + { 0 } +}; + +/* + * pci_dev_specific_acs_enabled - check whether device provides ACS controls + * @dev: PCI device + * @acs_flags: Bitmask of desired ACS controls + * + * Returns: + * -ENOTTY: No quirk applies to this device; we can't tell whether the + * device provides the desired controls + * 0: Device does not provide all the desired controls + * >0: Device provides all the controls in @acs_flags + */ +int pci_dev_specific_acs_enabled(struct pci_dev *dev, u16 acs_flags) +{ + const struct pci_dev_acs_enabled *i; + int ret; + + /* + * Allow devices that do not expose standard PCIe ACS capabilities + * or control to indicate their support here. Multi-function express + * devices which do not allow internal peer-to-peer between functions, + * but do not implement PCIe ACS may wish to return true here. + */ + for (i = pci_dev_acs_enabled; i->acs_enabled; i++) { + if ((i->vendor == dev->vendor || + i->vendor == (u16)PCI_ANY_ID) && + (i->device == dev->device || + i->device == (u16)PCI_ANY_ID)) { + ret = i->acs_enabled(dev, acs_flags); + if (ret >= 0) + return ret; + } + } + + return -ENOTTY; +} + +/* Config space offset of Root Complex Base Address register */ +#define INTEL_LPC_RCBA_REG 0xf0 +/* 31:14 RCBA address */ +#define INTEL_LPC_RCBA_MASK 0xffffc000 +/* RCBA Enable */ +#define INTEL_LPC_RCBA_ENABLE (1 << 0) + +/* Backbone Scratch Pad Register */ +#define INTEL_BSPR_REG 0x1104 +/* Backbone Peer Non-Posted Disable */ +#define INTEL_BSPR_REG_BPNPD (1 << 8) +/* Backbone Peer Posted Disable */ +#define INTEL_BSPR_REG_BPPD (1 << 9) + +/* Upstream Peer Decode Configuration Register */ +#define INTEL_UPDCR_REG 0x1014 +/* 5:0 Peer Decode Enable bits */ +#define INTEL_UPDCR_REG_MASK 0x3f + +static int pci_quirk_enable_intel_lpc_acs(struct pci_dev *dev) +{ + u32 rcba, bspr, updcr; + void __iomem *rcba_mem; + + /* + * Read the RCBA register from the LPC (D31:F0). PCH root ports + * are D28:F* and therefore get probed before LPC, thus we can't + * use pci_get_slot()/pci_read_config_dword() here. + */ + pci_bus_read_config_dword(dev->bus, PCI_DEVFN(31, 0), + INTEL_LPC_RCBA_REG, &rcba); + if (!(rcba & INTEL_LPC_RCBA_ENABLE)) + return -EINVAL; + + rcba_mem = ioremap(rcba & INTEL_LPC_RCBA_MASK, + PAGE_ALIGN(INTEL_UPDCR_REG)); + if (!rcba_mem) + return -ENOMEM; + + /* + * The BSPR can disallow peer cycles, but it's set by soft strap and + * therefore read-only. If both posted and non-posted peer cycles are + * disallowed, we're ok. If either are allowed, then we need to use + * the UPDCR to disable peer decodes for each port. This provides the + * PCIe ACS equivalent of PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF + */ + bspr = readl(rcba_mem + INTEL_BSPR_REG); + bspr &= INTEL_BSPR_REG_BPNPD | INTEL_BSPR_REG_BPPD; + if (bspr != (INTEL_BSPR_REG_BPNPD | INTEL_BSPR_REG_BPPD)) { + updcr = readl(rcba_mem + INTEL_UPDCR_REG); + if (updcr & INTEL_UPDCR_REG_MASK) { + pci_info(dev, "Disabling UPDCR peer decodes\n"); + updcr &= ~INTEL_UPDCR_REG_MASK; + writel(updcr, rcba_mem + INTEL_UPDCR_REG); + } + } + + iounmap(rcba_mem); + return 0; +} + +/* Miscellaneous Port Configuration register */ +#define INTEL_MPC_REG 0xd8 +/* MPC: Invalid Receive Bus Number Check Enable */ +#define INTEL_MPC_REG_IRBNCE (1 << 26) + +static void pci_quirk_enable_intel_rp_mpc_acs(struct pci_dev *dev) +{ + u32 mpc; + + /* + * When enabled, the IRBNCE bit of the MPC register enables the + * equivalent of PCI ACS Source Validation (PCI_ACS_SV), which + * ensures that requester IDs fall within the bus number range + * of the bridge. Enable if not already. + */ + pci_read_config_dword(dev, INTEL_MPC_REG, &mpc); + if (!(mpc & INTEL_MPC_REG_IRBNCE)) { + pci_info(dev, "Enabling MPC IRBNCE\n"); + mpc |= INTEL_MPC_REG_IRBNCE; + pci_write_config_word(dev, INTEL_MPC_REG, mpc); + } +} + +/* + * Currently this quirk does the equivalent of + * PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF + * + * TODO: This quirk also needs to do equivalent of PCI_ACS_TB, + * if dev->external_facing || dev->untrusted + */ +static int pci_quirk_enable_intel_pch_acs(struct pci_dev *dev) +{ + if (!pci_quirk_intel_pch_acs_match(dev)) + return -ENOTTY; + + if (pci_quirk_enable_intel_lpc_acs(dev)) { + pci_warn(dev, "Failed to enable Intel PCH ACS quirk\n"); + return 0; + } + + pci_quirk_enable_intel_rp_mpc_acs(dev); + + dev->dev_flags |= PCI_DEV_FLAGS_ACS_ENABLED_QUIRK; + + pci_info(dev, "Intel PCH root port ACS workaround enabled\n"); + + return 0; +} + +static int pci_quirk_enable_intel_spt_pch_acs(struct pci_dev *dev) +{ + int pos; + u32 cap, ctrl; + + if (!pci_quirk_intel_spt_pch_acs_match(dev)) + return -ENOTTY; + + pos = dev->acs_cap; + if (!pos) + return -ENOTTY; + + pci_read_config_dword(dev, pos + PCI_ACS_CAP, &cap); + pci_read_config_dword(dev, pos + INTEL_SPT_ACS_CTRL, &ctrl); + + ctrl |= (cap & PCI_ACS_SV); + ctrl |= (cap & PCI_ACS_RR); + ctrl |= (cap & PCI_ACS_CR); + ctrl |= (cap & PCI_ACS_UF); + + if (pci_ats_disabled() || dev->external_facing || dev->untrusted) + ctrl |= (cap & PCI_ACS_TB); + + pci_write_config_dword(dev, pos + INTEL_SPT_ACS_CTRL, ctrl); + + pci_info(dev, "Intel SPT PCH root port ACS workaround enabled\n"); + + return 0; +} + +static int pci_quirk_disable_intel_spt_pch_acs_redir(struct pci_dev *dev) +{ + int pos; + u32 cap, ctrl; + + if (!pci_quirk_intel_spt_pch_acs_match(dev)) + return -ENOTTY; + + pos = dev->acs_cap; + if (!pos) + return -ENOTTY; + + pci_read_config_dword(dev, pos + PCI_ACS_CAP, &cap); + pci_read_config_dword(dev, pos + INTEL_SPT_ACS_CTRL, &ctrl); + + ctrl &= ~(PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_EC); + + pci_write_config_dword(dev, pos + INTEL_SPT_ACS_CTRL, ctrl); + + pci_info(dev, "Intel SPT PCH root port workaround: disabled ACS redirect\n"); + + return 0; +} + +static const struct pci_dev_acs_ops { + u16 vendor; + u16 device; + int (*enable_acs)(struct pci_dev *dev); + int (*disable_acs_redir)(struct pci_dev *dev); +} pci_dev_acs_ops[] = { + { PCI_VENDOR_ID_INTEL, PCI_ANY_ID, + .enable_acs = pci_quirk_enable_intel_pch_acs, + }, + { PCI_VENDOR_ID_INTEL, PCI_ANY_ID, + .enable_acs = pci_quirk_enable_intel_spt_pch_acs, + .disable_acs_redir = pci_quirk_disable_intel_spt_pch_acs_redir, + }, +}; + +int pci_dev_specific_enable_acs(struct pci_dev *dev) +{ + const struct pci_dev_acs_ops *p; + int i, ret; + + for (i = 0; i < ARRAY_SIZE(pci_dev_acs_ops); i++) { + p = &pci_dev_acs_ops[i]; + if ((p->vendor == dev->vendor || + p->vendor == (u16)PCI_ANY_ID) && + (p->device == dev->device || + p->device == (u16)PCI_ANY_ID) && + p->enable_acs) { + ret = p->enable_acs(dev); + if (ret >= 0) + return ret; + } + } + + return -ENOTTY; +} + +int pci_dev_specific_disable_acs_redir(struct pci_dev *dev) +{ + const struct pci_dev_acs_ops *p; + int i, ret; + + for (i = 0; i < ARRAY_SIZE(pci_dev_acs_ops); i++) { + p = &pci_dev_acs_ops[i]; + if ((p->vendor == dev->vendor || + p->vendor == (u16)PCI_ANY_ID) && + (p->device == dev->device || + p->device == (u16)PCI_ANY_ID) && + p->disable_acs_redir) { + ret = p->disable_acs_redir(dev); + if (ret >= 0) + return ret; + } + } + + return -ENOTTY; +} + +/* + * The PCI capabilities list for Intel DH895xCC VFs (device ID 0x0443) with + * QuickAssist Technology (QAT) is prematurely terminated in hardware. The + * Next Capability pointer in the MSI Capability Structure should point to + * the PCIe Capability Structure but is incorrectly hardwired as 0 terminating + * the list. + */ +static void quirk_intel_qat_vf_cap(struct pci_dev *pdev) +{ + int pos, i = 0, ret; + u8 next_cap; + u16 reg16, *cap; + struct pci_cap_saved_state *state; + + /* Bail if the hardware bug is fixed */ + if (pdev->pcie_cap || pci_find_capability(pdev, PCI_CAP_ID_EXP)) + return; + + /* Bail if MSI Capability Structure is not found for some reason */ + pos = pci_find_capability(pdev, PCI_CAP_ID_MSI); + if (!pos) + return; + + /* + * Bail if Next Capability pointer in the MSI Capability Structure + * is not the expected incorrect 0x00. + */ + pci_read_config_byte(pdev, pos + 1, &next_cap); + if (next_cap) + return; + + /* + * PCIe Capability Structure is expected to be at 0x50 and should + * terminate the list (Next Capability pointer is 0x00). Verify + * Capability Id and Next Capability pointer is as expected. + * Open-code some of set_pcie_port_type() and pci_cfg_space_size_ext() + * to correctly set kernel data structures which have already been + * set incorrectly due to the hardware bug. + */ + pos = 0x50; + pci_read_config_word(pdev, pos, ®16); + if (reg16 == (0x0000 | PCI_CAP_ID_EXP)) { + u32 status; +#ifndef PCI_EXP_SAVE_REGS +#define PCI_EXP_SAVE_REGS 7 +#endif + int size = PCI_EXP_SAVE_REGS * sizeof(u16); + + pdev->pcie_cap = pos; + pci_read_config_word(pdev, pos + PCI_EXP_FLAGS, ®16); + pdev->pcie_flags_reg = reg16; + pci_read_config_word(pdev, pos + PCI_EXP_DEVCAP, ®16); + pdev->pcie_mpss = reg16 & PCI_EXP_DEVCAP_PAYLOAD; + + pdev->cfg_size = PCI_CFG_SPACE_EXP_SIZE; + ret = pci_read_config_dword(pdev, PCI_CFG_SPACE_SIZE, &status); + if ((ret != PCIBIOS_SUCCESSFUL) || (PCI_POSSIBLE_ERROR(status))) + pdev->cfg_size = PCI_CFG_SPACE_SIZE; + + if (pci_find_saved_cap(pdev, PCI_CAP_ID_EXP)) + return; + + /* Save PCIe cap */ + state = kzalloc(sizeof(*state) + size, GFP_KERNEL); + if (!state) + return; + + state->cap.cap_nr = PCI_CAP_ID_EXP; + state->cap.cap_extended = 0; + state->cap.size = size; + cap = (u16 *)&state->cap.data[0]; + pcie_capability_read_word(pdev, PCI_EXP_DEVCTL, &cap[i++]); + pcie_capability_read_word(pdev, PCI_EXP_LNKCTL, &cap[i++]); + pcie_capability_read_word(pdev, PCI_EXP_SLTCTL, &cap[i++]); + pcie_capability_read_word(pdev, PCI_EXP_RTCTL, &cap[i++]); + pcie_capability_read_word(pdev, PCI_EXP_DEVCTL2, &cap[i++]); + pcie_capability_read_word(pdev, PCI_EXP_LNKCTL2, &cap[i++]); + pcie_capability_read_word(pdev, PCI_EXP_SLTCTL2, &cap[i++]); + hlist_add_head(&state->next, &pdev->saved_cap_space); + } +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x443, quirk_intel_qat_vf_cap); + +/* + * FLR may cause the following to devices to hang: + * + * AMD Starship/Matisse HD Audio Controller 0x1487 + * AMD Starship USB 3.0 Host Controller 0x148c + * AMD Matisse USB 3.0 Host Controller 0x149c + * Intel 82579LM Gigabit Ethernet Controller 0x1502 + * Intel 82579V Gigabit Ethernet Controller 0x1503 + * + */ +static void quirk_no_flr(struct pci_dev *dev) +{ + dev->dev_flags |= PCI_DEV_FLAGS_NO_FLR_RESET; +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AMD, 0x1487, quirk_no_flr); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AMD, 0x148c, quirk_no_flr); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AMD, 0x149c, quirk_no_flr); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AMD, 0x7901, quirk_no_flr); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1502, quirk_no_flr); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1503, quirk_no_flr); + +/* FLR may cause the SolidRun SNET DPU (rev 0x1) to hang */ +static void quirk_no_flr_snet(struct pci_dev *dev) +{ + if (dev->revision == 0x1) + quirk_no_flr(dev); +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SOLIDRUN, 0x1000, quirk_no_flr_snet); + +static void quirk_no_ext_tags(struct pci_dev *pdev) +{ + struct pci_host_bridge *bridge = pci_find_host_bridge(pdev->bus); + + if (!bridge) + return; + + bridge->no_ext_tags = 1; + pci_info(pdev, "disabling Extended Tags (this device can't handle them)\n"); + + pci_walk_bus(bridge->bus, pci_configure_extended_tags, NULL); +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, 0x0132, quirk_no_ext_tags); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, 0x0140, quirk_no_ext_tags); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, 0x0141, quirk_no_ext_tags); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, 0x0142, quirk_no_ext_tags); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, 0x0144, quirk_no_ext_tags); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, 0x0420, quirk_no_ext_tags); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, 0x0422, quirk_no_ext_tags); + +#ifdef CONFIG_PCI_ATS +static void quirk_no_ats(struct pci_dev *pdev) +{ + pci_info(pdev, "disabling ATS\n"); + pdev->ats_cap = 0; +} + +/* + * Some devices require additional driver setup to enable ATS. Don't use + * ATS for those devices as ATS will be enabled before the driver has had a + * chance to load and configure the device. + */ +static void quirk_amd_harvest_no_ats(struct pci_dev *pdev) +{ + if (pdev->device == 0x15d8) { + if (pdev->revision == 0xcf && + pdev->subsystem_vendor == 0xea50 && + (pdev->subsystem_device == 0xce19 || + pdev->subsystem_device == 0xcc10 || + pdev->subsystem_device == 0xcc08)) + quirk_no_ats(pdev); + } else { + quirk_no_ats(pdev); + } +} + +/* AMD Stoney platform GPU */ +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x98e4, quirk_amd_harvest_no_ats); +/* AMD Iceland dGPU */ +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x6900, quirk_amd_harvest_no_ats); +/* AMD Navi10 dGPU */ +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7310, quirk_amd_harvest_no_ats); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7312, quirk_amd_harvest_no_ats); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7318, quirk_amd_harvest_no_ats); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7319, quirk_amd_harvest_no_ats); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x731a, quirk_amd_harvest_no_ats); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x731b, quirk_amd_harvest_no_ats); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x731e, quirk_amd_harvest_no_ats); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x731f, quirk_amd_harvest_no_ats); +/* AMD Navi14 dGPU */ +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7340, quirk_amd_harvest_no_ats); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7341, quirk_amd_harvest_no_ats); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7347, quirk_amd_harvest_no_ats); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x734f, quirk_amd_harvest_no_ats); +/* AMD Raven platform iGPU */ +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x15d8, quirk_amd_harvest_no_ats); + +/* + * Intel IPU E2000 revisions before C0 implement incorrect endianness + * in ATS Invalidate Request message body. Disable ATS for those devices. + */ +static void quirk_intel_e2000_no_ats(struct pci_dev *pdev) +{ + if (pdev->revision < 0x20) + quirk_no_ats(pdev); +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1451, quirk_intel_e2000_no_ats); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1452, quirk_intel_e2000_no_ats); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1453, quirk_intel_e2000_no_ats); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1454, quirk_intel_e2000_no_ats); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1455, quirk_intel_e2000_no_ats); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1457, quirk_intel_e2000_no_ats); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1459, quirk_intel_e2000_no_ats); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x145a, quirk_intel_e2000_no_ats); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x145c, quirk_intel_e2000_no_ats); +#endif /* CONFIG_PCI_ATS */ + +/* Freescale PCIe doesn't support MSI in RC mode */ +static void quirk_fsl_no_msi(struct pci_dev *pdev) +{ + if (pci_pcie_type(pdev) == PCI_EXP_TYPE_ROOT_PORT) + pdev->no_msi = 1; +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_FREESCALE, PCI_ANY_ID, quirk_fsl_no_msi); + +/* + * Although not allowed by the spec, some multi-function devices have + * dependencies of one function (consumer) on another (supplier). For the + * consumer to work in D0, the supplier must also be in D0. Create a + * device link from the consumer to the supplier to enforce this + * dependency. Runtime PM is allowed by default on the consumer to prevent + * it from permanently keeping the supplier awake. + */ +static void pci_create_device_link(struct pci_dev *pdev, unsigned int consumer, + unsigned int supplier, unsigned int class, + unsigned int class_shift) +{ + struct pci_dev *supplier_pdev; + + if (PCI_FUNC(pdev->devfn) != consumer) + return; + + supplier_pdev = pci_get_domain_bus_and_slot(pci_domain_nr(pdev->bus), + pdev->bus->number, + PCI_DEVFN(PCI_SLOT(pdev->devfn), supplier)); + if (!supplier_pdev || (supplier_pdev->class >> class_shift) != class) { + pci_dev_put(supplier_pdev); + return; + } + + if (device_link_add(&pdev->dev, &supplier_pdev->dev, + DL_FLAG_STATELESS | DL_FLAG_PM_RUNTIME)) + pci_info(pdev, "D0 power state depends on %s\n", + pci_name(supplier_pdev)); + else + pci_err(pdev, "Cannot enforce power dependency on %s\n", + pci_name(supplier_pdev)); + + pm_runtime_allow(&pdev->dev); + pci_dev_put(supplier_pdev); +} + +/* + * Create device link for GPUs with integrated HDA controller for streaming + * audio to attached displays. + */ +static void quirk_gpu_hda(struct pci_dev *hda) +{ + pci_create_device_link(hda, 1, 0, PCI_BASE_CLASS_DISPLAY, 16); +} +DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_ATI, PCI_ANY_ID, + PCI_CLASS_MULTIMEDIA_HD_AUDIO, 8, quirk_gpu_hda); +DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_AMD, PCI_ANY_ID, + PCI_CLASS_MULTIMEDIA_HD_AUDIO, 8, quirk_gpu_hda); +DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, + PCI_CLASS_MULTIMEDIA_HD_AUDIO, 8, quirk_gpu_hda); + +/* + * Create device link for GPUs with integrated USB xHCI Host + * controller to VGA. + */ +static void quirk_gpu_usb(struct pci_dev *usb) +{ + pci_create_device_link(usb, 2, 0, PCI_BASE_CLASS_DISPLAY, 16); +} +DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, + PCI_CLASS_SERIAL_USB, 8, quirk_gpu_usb); +DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_ATI, PCI_ANY_ID, + PCI_CLASS_SERIAL_USB, 8, quirk_gpu_usb); + +/* + * Create device link for GPUs with integrated Type-C UCSI controller + * to VGA. Currently there is no class code defined for UCSI device over PCI + * so using UNKNOWN class for now and it will be updated when UCSI + * over PCI gets a class code. + */ +#define PCI_CLASS_SERIAL_UNKNOWN 0x0c80 +static void quirk_gpu_usb_typec_ucsi(struct pci_dev *ucsi) +{ + pci_create_device_link(ucsi, 3, 0, PCI_BASE_CLASS_DISPLAY, 16); +} +DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, + PCI_CLASS_SERIAL_UNKNOWN, 8, + quirk_gpu_usb_typec_ucsi); +DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_ATI, PCI_ANY_ID, + PCI_CLASS_SERIAL_UNKNOWN, 8, + quirk_gpu_usb_typec_ucsi); + +/* + * Enable the NVIDIA GPU integrated HDA controller if the BIOS left it + * disabled. https://devtalk.nvidia.com/default/topic/1024022 + */ +static void quirk_nvidia_hda(struct pci_dev *gpu) +{ + u8 hdr_type; + u32 val; + + /* There was no integrated HDA controller before MCP89 */ + if (gpu->device < PCI_DEVICE_ID_NVIDIA_GEFORCE_320M) + return; + + /* Bit 25 at offset 0x488 enables the HDA controller */ + pci_read_config_dword(gpu, 0x488, &val); + if (val & BIT(25)) + return; + + pci_info(gpu, "Enabling HDA controller\n"); + pci_write_config_dword(gpu, 0x488, val | BIT(25)); + + /* The GPU becomes a multi-function device when the HDA is enabled */ + pci_read_config_byte(gpu, PCI_HEADER_TYPE, &hdr_type); + gpu->multifunction = !!(hdr_type & 0x80); +} +DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, + PCI_BASE_CLASS_DISPLAY, 16, quirk_nvidia_hda); +DECLARE_PCI_FIXUP_CLASS_RESUME_EARLY(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, + PCI_BASE_CLASS_DISPLAY, 16, quirk_nvidia_hda); + +/* + * Some IDT switches incorrectly flag an ACS Source Validation error on + * completions for config read requests even though PCIe r4.0, sec + * 6.12.1.1, says that completions are never affected by ACS Source + * Validation. Here's the text of IDT 89H32H8G3-YC, erratum #36: + * + * Item #36 - Downstream port applies ACS Source Validation to Completions + * Section 6.12.1.1 of the PCI Express Base Specification 3.1 states that + * completions are never affected by ACS Source Validation. However, + * completions received by a downstream port of the PCIe switch from a + * device that has not yet captured a PCIe bus number are incorrectly + * dropped by ACS Source Validation by the switch downstream port. + * + * The workaround suggested by IDT is to issue a config write to the + * downstream device before issuing the first config read. This allows the + * downstream device to capture its bus and device numbers (see PCIe r4.0, + * sec 2.2.9), thus avoiding the ACS error on the completion. + * + * However, we don't know when the device is ready to accept the config + * write, so we do config reads until we receive a non-Config Request Retry + * Status, then do the config write. + * + * To avoid hitting the erratum when doing the config reads, we disable ACS + * SV around this process. + */ +int pci_idt_bus_quirk(struct pci_bus *bus, int devfn, u32 *l, int timeout) +{ + int pos; + u16 ctrl = 0; + bool found; + struct pci_dev *bridge = bus->self; + + pos = bridge->acs_cap; + + /* Disable ACS SV before initial config reads */ + if (pos) { + pci_read_config_word(bridge, pos + PCI_ACS_CTRL, &ctrl); + if (ctrl & PCI_ACS_SV) + pci_write_config_word(bridge, pos + PCI_ACS_CTRL, + ctrl & ~PCI_ACS_SV); + } + + found = pci_bus_generic_read_dev_vendor_id(bus, devfn, l, timeout); + + /* Write Vendor ID (read-only) so the endpoint latches its bus/dev */ + if (found) + pci_bus_write_config_word(bus, devfn, PCI_VENDOR_ID, 0); + + /* Re-enable ACS_SV if it was previously enabled */ + if (ctrl & PCI_ACS_SV) + pci_write_config_word(bridge, pos + PCI_ACS_CTRL, ctrl); + + return found; +} + +/* + * Microsemi Switchtec NTB uses devfn proxy IDs to move TLPs between + * NT endpoints via the internal switch fabric. These IDs replace the + * originating Requester ID TLPs which access host memory on peer NTB + * ports. Therefore, all proxy IDs must be aliased to the NTB device + * to permit access when the IOMMU is turned on. + */ +static void quirk_switchtec_ntb_dma_alias(struct pci_dev *pdev) +{ + void __iomem *mmio; + struct ntb_info_regs __iomem *mmio_ntb; + struct ntb_ctrl_regs __iomem *mmio_ctrl; + u64 partition_map; + u8 partition; + int pp; + + if (pci_enable_device(pdev)) { + pci_err(pdev, "Cannot enable Switchtec device\n"); + return; + } + + mmio = pci_iomap(pdev, 0, 0); + if (mmio == NULL) { + pci_disable_device(pdev); + pci_err(pdev, "Cannot iomap Switchtec device\n"); + return; + } + + pci_info(pdev, "Setting Switchtec proxy ID aliases\n"); + + mmio_ntb = mmio + SWITCHTEC_GAS_NTB_OFFSET; + mmio_ctrl = (void __iomem *) mmio_ntb + SWITCHTEC_NTB_REG_CTRL_OFFSET; + + partition = ioread8(&mmio_ntb->partition_id); + + partition_map = ioread32(&mmio_ntb->ep_map); + partition_map |= ((u64) ioread32(&mmio_ntb->ep_map + 4)) << 32; + partition_map &= ~(1ULL << partition); + + for (pp = 0; pp < (sizeof(partition_map) * 8); pp++) { + struct ntb_ctrl_regs __iomem *mmio_peer_ctrl; + u32 table_sz = 0; + int te; + + if (!(partition_map & (1ULL << pp))) + continue; + + pci_dbg(pdev, "Processing partition %d\n", pp); + + mmio_peer_ctrl = &mmio_ctrl[pp]; + + table_sz = ioread16(&mmio_peer_ctrl->req_id_table_size); + if (!table_sz) { + pci_warn(pdev, "Partition %d table_sz 0\n", pp); + continue; + } + + if (table_sz > 512) { + pci_warn(pdev, + "Invalid Switchtec partition %d table_sz %d\n", + pp, table_sz); + continue; + } + + for (te = 0; te < table_sz; te++) { + u32 rid_entry; + u8 devfn; + + rid_entry = ioread32(&mmio_peer_ctrl->req_id_table[te]); + devfn = (rid_entry >> 1) & 0xFF; + pci_dbg(pdev, + "Aliasing Partition %d Proxy ID %02x.%d\n", + pp, PCI_SLOT(devfn), PCI_FUNC(devfn)); + pci_add_dma_alias(pdev, devfn, 1); + } + } + + pci_iounmap(pdev, mmio); + pci_disable_device(pdev); +} +#define SWITCHTEC_QUIRK(vid) \ + DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_MICROSEMI, vid, \ + PCI_CLASS_BRIDGE_OTHER, 8, quirk_switchtec_ntb_dma_alias) + +SWITCHTEC_QUIRK(0x8531); /* PFX 24xG3 */ +SWITCHTEC_QUIRK(0x8532); /* PFX 32xG3 */ +SWITCHTEC_QUIRK(0x8533); /* PFX 48xG3 */ +SWITCHTEC_QUIRK(0x8534); /* PFX 64xG3 */ +SWITCHTEC_QUIRK(0x8535); /* PFX 80xG3 */ +SWITCHTEC_QUIRK(0x8536); /* PFX 96xG3 */ +SWITCHTEC_QUIRK(0x8541); /* PSX 24xG3 */ +SWITCHTEC_QUIRK(0x8542); /* PSX 32xG3 */ +SWITCHTEC_QUIRK(0x8543); /* PSX 48xG3 */ +SWITCHTEC_QUIRK(0x8544); /* PSX 64xG3 */ +SWITCHTEC_QUIRK(0x8545); /* PSX 80xG3 */ +SWITCHTEC_QUIRK(0x8546); /* PSX 96xG3 */ +SWITCHTEC_QUIRK(0x8551); /* PAX 24XG3 */ +SWITCHTEC_QUIRK(0x8552); /* PAX 32XG3 */ +SWITCHTEC_QUIRK(0x8553); /* PAX 48XG3 */ +SWITCHTEC_QUIRK(0x8554); /* PAX 64XG3 */ +SWITCHTEC_QUIRK(0x8555); /* PAX 80XG3 */ +SWITCHTEC_QUIRK(0x8556); /* PAX 96XG3 */ +SWITCHTEC_QUIRK(0x8561); /* PFXL 24XG3 */ +SWITCHTEC_QUIRK(0x8562); /* PFXL 32XG3 */ +SWITCHTEC_QUIRK(0x8563); /* PFXL 48XG3 */ +SWITCHTEC_QUIRK(0x8564); /* PFXL 64XG3 */ +SWITCHTEC_QUIRK(0x8565); /* PFXL 80XG3 */ +SWITCHTEC_QUIRK(0x8566); /* PFXL 96XG3 */ +SWITCHTEC_QUIRK(0x8571); /* PFXI 24XG3 */ +SWITCHTEC_QUIRK(0x8572); /* PFXI 32XG3 */ +SWITCHTEC_QUIRK(0x8573); /* PFXI 48XG3 */ +SWITCHTEC_QUIRK(0x8574); /* PFXI 64XG3 */ +SWITCHTEC_QUIRK(0x8575); /* PFXI 80XG3 */ +SWITCHTEC_QUIRK(0x8576); /* PFXI 96XG3 */ +SWITCHTEC_QUIRK(0x4000); /* PFX 100XG4 */ +SWITCHTEC_QUIRK(0x4084); /* PFX 84XG4 */ +SWITCHTEC_QUIRK(0x4068); /* PFX 68XG4 */ +SWITCHTEC_QUIRK(0x4052); /* PFX 52XG4 */ +SWITCHTEC_QUIRK(0x4036); /* PFX 36XG4 */ +SWITCHTEC_QUIRK(0x4028); /* PFX 28XG4 */ +SWITCHTEC_QUIRK(0x4100); /* PSX 100XG4 */ +SWITCHTEC_QUIRK(0x4184); /* PSX 84XG4 */ +SWITCHTEC_QUIRK(0x4168); /* PSX 68XG4 */ +SWITCHTEC_QUIRK(0x4152); /* PSX 52XG4 */ +SWITCHTEC_QUIRK(0x4136); /* PSX 36XG4 */ +SWITCHTEC_QUIRK(0x4128); /* PSX 28XG4 */ +SWITCHTEC_QUIRK(0x4200); /* PAX 100XG4 */ +SWITCHTEC_QUIRK(0x4284); /* PAX 84XG4 */ +SWITCHTEC_QUIRK(0x4268); /* PAX 68XG4 */ +SWITCHTEC_QUIRK(0x4252); /* PAX 52XG4 */ +SWITCHTEC_QUIRK(0x4236); /* PAX 36XG4 */ +SWITCHTEC_QUIRK(0x4228); /* PAX 28XG4 */ +SWITCHTEC_QUIRK(0x4352); /* PFXA 52XG4 */ +SWITCHTEC_QUIRK(0x4336); /* PFXA 36XG4 */ +SWITCHTEC_QUIRK(0x4328); /* PFXA 28XG4 */ +SWITCHTEC_QUIRK(0x4452); /* PSXA 52XG4 */ +SWITCHTEC_QUIRK(0x4436); /* PSXA 36XG4 */ +SWITCHTEC_QUIRK(0x4428); /* PSXA 28XG4 */ +SWITCHTEC_QUIRK(0x4552); /* PAXA 52XG4 */ +SWITCHTEC_QUIRK(0x4536); /* PAXA 36XG4 */ +SWITCHTEC_QUIRK(0x4528); /* PAXA 28XG4 */ +SWITCHTEC_QUIRK(0x5000); /* PFX 100XG5 */ +SWITCHTEC_QUIRK(0x5084); /* PFX 84XG5 */ +SWITCHTEC_QUIRK(0x5068); /* PFX 68XG5 */ +SWITCHTEC_QUIRK(0x5052); /* PFX 52XG5 */ +SWITCHTEC_QUIRK(0x5036); /* PFX 36XG5 */ +SWITCHTEC_QUIRK(0x5028); /* PFX 28XG5 */ +SWITCHTEC_QUIRK(0x5100); /* PSX 100XG5 */ +SWITCHTEC_QUIRK(0x5184); /* PSX 84XG5 */ +SWITCHTEC_QUIRK(0x5168); /* PSX 68XG5 */ +SWITCHTEC_QUIRK(0x5152); /* PSX 52XG5 */ +SWITCHTEC_QUIRK(0x5136); /* PSX 36XG5 */ +SWITCHTEC_QUIRK(0x5128); /* PSX 28XG5 */ +SWITCHTEC_QUIRK(0x5200); /* PAX 100XG5 */ +SWITCHTEC_QUIRK(0x5284); /* PAX 84XG5 */ +SWITCHTEC_QUIRK(0x5268); /* PAX 68XG5 */ +SWITCHTEC_QUIRK(0x5252); /* PAX 52XG5 */ +SWITCHTEC_QUIRK(0x5236); /* PAX 36XG5 */ +SWITCHTEC_QUIRK(0x5228); /* PAX 28XG5 */ +SWITCHTEC_QUIRK(0x5300); /* PFXA 100XG5 */ +SWITCHTEC_QUIRK(0x5384); /* PFXA 84XG5 */ +SWITCHTEC_QUIRK(0x5368); /* PFXA 68XG5 */ +SWITCHTEC_QUIRK(0x5352); /* PFXA 52XG5 */ +SWITCHTEC_QUIRK(0x5336); /* PFXA 36XG5 */ +SWITCHTEC_QUIRK(0x5328); /* PFXA 28XG5 */ +SWITCHTEC_QUIRK(0x5400); /* PSXA 100XG5 */ +SWITCHTEC_QUIRK(0x5484); /* PSXA 84XG5 */ +SWITCHTEC_QUIRK(0x5468); /* PSXA 68XG5 */ +SWITCHTEC_QUIRK(0x5452); /* PSXA 52XG5 */ +SWITCHTEC_QUIRK(0x5436); /* PSXA 36XG5 */ +SWITCHTEC_QUIRK(0x5428); /* PSXA 28XG5 */ +SWITCHTEC_QUIRK(0x5500); /* PAXA 100XG5 */ +SWITCHTEC_QUIRK(0x5584); /* PAXA 84XG5 */ +SWITCHTEC_QUIRK(0x5568); /* PAXA 68XG5 */ +SWITCHTEC_QUIRK(0x5552); /* PAXA 52XG5 */ +SWITCHTEC_QUIRK(0x5536); /* PAXA 36XG5 */ +SWITCHTEC_QUIRK(0x5528); /* PAXA 28XG5 */ + +/* + * The PLX NTB uses devfn proxy IDs to move TLPs between NT endpoints. + * These IDs are used to forward responses to the originator on the other + * side of the NTB. Alias all possible IDs to the NTB to permit access when + * the IOMMU is turned on. + */ +static void quirk_plx_ntb_dma_alias(struct pci_dev *pdev) +{ + pci_info(pdev, "Setting PLX NTB proxy ID aliases\n"); + /* PLX NTB may use all 256 devfns */ + pci_add_dma_alias(pdev, 0, 256); +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_PLX, 0x87b0, quirk_plx_ntb_dma_alias); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_PLX, 0x87b1, quirk_plx_ntb_dma_alias); + +/* + * On Lenovo Thinkpad P50 SKUs with a Nvidia Quadro M1000M, the BIOS does + * not always reset the secondary Nvidia GPU between reboots if the system + * is configured to use Hybrid Graphics mode. This results in the GPU + * being left in whatever state it was in during the *previous* boot, which + * causes spurious interrupts from the GPU, which in turn causes us to + * disable the wrong IRQ and end up breaking the touchpad. Unsurprisingly, + * this also completely breaks nouveau. + * + * Luckily, it seems a simple reset of the Nvidia GPU brings it back to a + * clean state and fixes all these issues. + * + * When the machine is configured in Dedicated display mode, the issue + * doesn't occur. Fortunately the GPU advertises NoReset+ when in this + * mode, so we can detect that and avoid resetting it. + */ +static void quirk_reset_lenovo_thinkpad_p50_nvgpu(struct pci_dev *pdev) +{ + void __iomem *map; + int ret; + + if (pdev->subsystem_vendor != PCI_VENDOR_ID_LENOVO || + pdev->subsystem_device != 0x222e || + !pci_reset_supported(pdev)) + return; + + if (pci_enable_device_mem(pdev)) + return; + + /* + * Based on nvkm_device_ctor() in + * drivers/gpu/drm/nouveau/nvkm/engine/device/base.c + */ + map = pci_iomap(pdev, 0, 0x23000); + if (!map) { + pci_err(pdev, "Can't map MMIO space\n"); + goto out_disable; + } + + /* + * Make sure the GPU looks like it's been POSTed before resetting + * it. + */ + if (ioread32(map + 0x2240c) & 0x2) { + pci_info(pdev, FW_BUG "GPU left initialized by EFI, resetting\n"); + ret = pci_reset_bus(pdev); + if (ret < 0) + pci_err(pdev, "Failed to reset GPU: %d\n", ret); + } + + iounmap(map); +out_disable: + pci_disable_device(pdev); +} +DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_NVIDIA, 0x13b1, + PCI_CLASS_DISPLAY_VGA, 8, + quirk_reset_lenovo_thinkpad_p50_nvgpu); + +/* + * Device [1b21:2142] + * When in D0, PME# doesn't get asserted when plugging USB 3.0 device. + */ +static void pci_fixup_no_d0_pme(struct pci_dev *dev) +{ + pci_info(dev, "PME# does not work under D0, disabling it\n"); + dev->pme_support &= ~(PCI_PM_CAP_PME_D0 >> PCI_PM_CAP_PME_SHIFT); +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ASMEDIA, 0x2142, pci_fixup_no_d0_pme); + +/* + * Device 12d8:0x400e [OHCI] and 12d8:0x400f [EHCI] + * + * These devices advertise PME# support in all power states but don't + * reliably assert it. + * + * These devices also advertise MSI, but documentation (PI7C9X440SL.pdf) + * says "The MSI Function is not implemented on this device" in chapters + * 7.3.27, 7.3.29-7.3.31. + */ +static void pci_fixup_no_msi_no_pme(struct pci_dev *dev) +{ +#ifdef CONFIG_PCI_MSI + pci_info(dev, "MSI is not implemented on this device, disabling it\n"); + dev->no_msi = 1; +#endif + pci_info(dev, "PME# is unreliable, disabling it\n"); + dev->pme_support = 0; +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_PERICOM, 0x400e, pci_fixup_no_msi_no_pme); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_PERICOM, 0x400f, pci_fixup_no_msi_no_pme); + +static void apex_pci_fixup_class(struct pci_dev *pdev) +{ + pdev->class = (PCI_CLASS_SYSTEM_OTHER << 8) | pdev->class; +} +DECLARE_PCI_FIXUP_CLASS_HEADER(0x1ac1, 0x089a, + PCI_CLASS_NOT_DEFINED, 8, apex_pci_fixup_class); + +/* + * Pericom PI7C9X2G404/PI7C9X2G304/PI7C9X2G303 switch erratum E5 - + * ACS P2P Request Redirect is not functional + * + * When ACS P2P Request Redirect is enabled and bandwidth is not balanced + * between upstream and downstream ports, packets are queued in an internal + * buffer until CPLD packet. The workaround is to use the switch in store and + * forward mode. + */ +#define PI7C9X2Gxxx_MODE_REG 0x74 +#define PI7C9X2Gxxx_STORE_FORWARD_MODE BIT(0) +static void pci_fixup_pericom_acs_store_forward(struct pci_dev *pdev) +{ + struct pci_dev *upstream; + u16 val; + + /* Downstream ports only */ + if (pci_pcie_type(pdev) != PCI_EXP_TYPE_DOWNSTREAM) + return; + + /* Check for ACS P2P Request Redirect use */ + if (!pdev->acs_cap) + return; + pci_read_config_word(pdev, pdev->acs_cap + PCI_ACS_CTRL, &val); + if (!(val & PCI_ACS_RR)) + return; + + upstream = pci_upstream_bridge(pdev); + if (!upstream) + return; + + pci_read_config_word(upstream, PI7C9X2Gxxx_MODE_REG, &val); + if (!(val & PI7C9X2Gxxx_STORE_FORWARD_MODE)) { + pci_info(upstream, "Setting PI7C9X2Gxxx store-forward mode to avoid ACS erratum\n"); + pci_write_config_word(upstream, PI7C9X2Gxxx_MODE_REG, val | + PI7C9X2Gxxx_STORE_FORWARD_MODE); + } +} +/* + * Apply fixup on enable and on resume, in order to apply the fix up whenever + * ACS configuration changes or switch mode is reset + */ +DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_PERICOM, 0x2404, + pci_fixup_pericom_acs_store_forward); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_PERICOM, 0x2404, + pci_fixup_pericom_acs_store_forward); +DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_PERICOM, 0x2304, + pci_fixup_pericom_acs_store_forward); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_PERICOM, 0x2304, + pci_fixup_pericom_acs_store_forward); +DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_PERICOM, 0x2303, + pci_fixup_pericom_acs_store_forward); +DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_PERICOM, 0x2303, + pci_fixup_pericom_acs_store_forward); + +static void nvidia_ion_ahci_fixup(struct pci_dev *pdev) +{ + pdev->dev_flags |= PCI_DEV_FLAGS_HAS_MSI_MASKING; +} +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, 0x0ab8, nvidia_ion_ahci_fixup); + +static void rom_bar_overlap_defect(struct pci_dev *dev) +{ + pci_info(dev, "working around ROM BAR overlap defect\n"); + dev->rom_bar_overlap = 1; +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1533, rom_bar_overlap_defect); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1536, rom_bar_overlap_defect); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1537, rom_bar_overlap_defect); +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1538, rom_bar_overlap_defect); + +#ifdef CONFIG_PCIEASPM +/* + * Several Intel DG2 graphics devices advertise that they can only tolerate + * 1us latency when transitioning from L1 to L0, which may prevent ASPM L1 + * from being enabled. But in fact these devices can tolerate unlimited + * latency. Override their Device Capabilities value to allow ASPM L1 to + * be enabled. + */ +static void aspm_l1_acceptable_latency(struct pci_dev *dev) +{ + u32 l1_lat = FIELD_GET(PCI_EXP_DEVCAP_L1, dev->devcap); + + if (l1_lat < 7) { + dev->devcap |= FIELD_PREP(PCI_EXP_DEVCAP_L1, 7); + pci_info(dev, "ASPM: overriding L1 acceptable latency from %#x to 0x7\n", + l1_lat); + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f80, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f81, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f82, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f83, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f84, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f85, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f86, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f87, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f88, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x5690, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x5691, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x5692, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x5693, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x5694, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x5695, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a0, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a1, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a2, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a3, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a4, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a5, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a6, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56b0, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56b1, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56c0, aspm_l1_acceptable_latency); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56c1, aspm_l1_acceptable_latency); +#endif + +#ifdef CONFIG_PCIE_DPC +/* + * Intel Ice Lake, Tiger Lake and Alder Lake BIOS has a bug that clears + * the DPC RP PIO Log Size of the integrated Thunderbolt PCIe Root + * Ports. + */ +static void dpc_log_size(struct pci_dev *dev) +{ + u16 dpc, val; + + dpc = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_DPC); + if (!dpc) + return; + + pci_read_config_word(dev, dpc + PCI_EXP_DPC_CAP, &val); + if (!(val & PCI_EXP_DPC_CAP_RP_EXT)) + return; + + if (!((val & PCI_EXP_DPC_RP_PIO_LOG_SIZE) >> 8)) { + pci_info(dev, "Overriding RP PIO Log Size to 4\n"); + dev->dpc_rp_log_size = 4; + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x461f, dpc_log_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x462f, dpc_log_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x463f, dpc_log_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x466e, dpc_log_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x8a1d, dpc_log_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x8a1f, dpc_log_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x8a21, dpc_log_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x8a23, dpc_log_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a23, dpc_log_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a25, dpc_log_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a27, dpc_log_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a29, dpc_log_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a2b, dpc_log_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a2d, dpc_log_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a2f, dpc_log_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a31, dpc_log_size); +#endif + +/* + * For a PCI device with multiple downstream devices, its driver may use + * a flattened device tree to describe the downstream devices. + * To overlay the flattened device tree, the PCI device and all its ancestor + * devices need to have device tree nodes on system base device tree. Thus, + * before driver probing, it might need to add a device tree node as the final + * fixup. + */ +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_XILINX, 0x5020, of_pci_make_dev_node); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_XILINX, 0x5021, of_pci_make_dev_node); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_REDHAT, 0x0005, of_pci_make_dev_node); + +/* + * Devices known to require a longer delay before first config space access + * after reset recovery or resume from D3cold: + * + * VideoPropulsion (aka Genroco) Torrent QN16e MPEG QAM Modulator + */ +static void pci_fixup_d3cold_delay_1sec(struct pci_dev *pdev) +{ + pdev->d3cold_delay = 1000; +} +DECLARE_PCI_FIXUP_FINAL(0x5555, 0x0004, pci_fixup_d3cold_delay_1sec); -- cgit v1.2.3