From 638a9e433ecd61e64761352dbec1fa4f5874c941 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Wed, 7 Aug 2024 15:18:06 +0200 Subject: Merging upstream version 6.10.3. Signed-off-by: Daniel Baumann --- drivers/tty/serial/8250/8250_exar.c | 1009 +++++++++++++++++++++++++++++++---- 1 file changed, 904 insertions(+), 105 deletions(-) (limited to 'drivers/tty/serial/8250/8250_exar.c') diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c index 4d1e07343d..616128254b 100644 --- a/drivers/tty/serial/8250/8250_exar.c +++ b/drivers/tty/serial/8250/8250_exar.c @@ -6,6 +6,7 @@ * * Copyright (C) 2017 Sudip Mukherjee, All Rights Reserved. */ +#include #include #include #include @@ -128,12 +129,25 @@ #define UART_EXAR_DLD 0x02 /* Divisor Fractional */ #define UART_EXAR_DLD_485_POLARITY 0x80 /* RS-485 Enable Signal Polarity */ +/* EEPROM registers */ +#define UART_EXAR_REGB 0x8e +#define UART_EXAR_REGB_EECK BIT(4) +#define UART_EXAR_REGB_EECS BIT(5) +#define UART_EXAR_REGB_EEDI BIT(6) +#define UART_EXAR_REGB_EEDO BIT(7) +#define UART_EXAR_REGB_EE_ADDR_SIZE 6 +#define UART_EXAR_REGB_EE_DATA_SIZE 16 + +#define UART_EXAR_XR17C15X_PORT_OFFSET 0x200 +#define UART_EXAR_XR17V25X_PORT_OFFSET 0x200 +#define UART_EXAR_XR17V35X_PORT_OFFSET 0x400 + /* * IOT2040 MPIO wiring semantics: * * MPIO Port Function * ---- ---- -------- - * 0 2 Mode bit 0 + * 0 2 Mode bit 0 * 1 2 Mode bit 1 * 2 2 Terminate bus * 3 - @@ -163,38 +177,300 @@ #define IOT2040_UARTS_ENABLE 0x03 #define IOT2040_UARTS_GPIO_HI_MODE 0xF8 /* enable & LED as outputs */ +/* CTI EEPROM offsets */ +#define CTI_EE_OFF_XR17C15X_OSC_FREQ 0x04 /* 2 words */ +#define CTI_EE_OFF_XR17V25X_OSC_FREQ 0x08 /* 2 words */ +#define CTI_EE_OFF_XR17C15X_PART_NUM 0x0A /* 4 words */ +#define CTI_EE_OFF_XR17V25X_PART_NUM 0x0E /* 4 words */ +#define CTI_EE_OFF_XR17C15X_SERIAL_NUM 0x0E /* 1 word */ +#define CTI_EE_OFF_XR17V25X_SERIAL_NUM 0x12 /* 1 word */ +#define CTI_EE_OFF_XR17V35X_SERIAL_NUM 0x11 /* 2 word */ +#define CTI_EE_OFF_XR17V35X_BRD_FLAGS 0x13 /* 1 word */ +#define CTI_EE_OFF_XR17V35X_PORT_FLAGS 0x14 /* 1 word */ + +#define CTI_EE_MASK_PORT_FLAGS_TYPE GENMASK(7, 0) +#define CTI_EE_MASK_OSC_FREQ_LOWER GENMASK(15, 0) +#define CTI_EE_MASK_OSC_FREQ_UPPER GENMASK(31, 16) + +#define CTI_FPGA_RS485_IO_REG 0x2008 +#define CTI_FPGA_CFG_INT_EN_REG 0x48 +#define CTI_FPGA_CFG_INT_EN_EXT_BIT BIT(15) /* External int enable bit */ + +#define CTI_DEFAULT_PCI_OSC_FREQ 29491200 +#define CTI_DEFAULT_PCIE_OSC_FREQ 125000000 +#define CTI_DEFAULT_FPGA_OSC_FREQ 33333333 + +/* + * CTI Serial port line types. These match the values stored in the first + * nibble of the CTI EEPROM port_flags word. + */ +enum cti_port_type { + CTI_PORT_TYPE_NONE = 0, + CTI_PORT_TYPE_RS232, // RS232 ONLY + CTI_PORT_TYPE_RS422_485, // RS422/RS485 ONLY + CTI_PORT_TYPE_RS232_422_485_HW, // RS232/422/485 HW ONLY Switchable + CTI_PORT_TYPE_RS232_422_485_SW, // RS232/422/485 SW ONLY Switchable + CTI_PORT_TYPE_RS232_422_485_4B, // RS232/422/485 HW/SW (4bit ex. BCG004) + CTI_PORT_TYPE_RS232_422_485_2B, // RS232/422/485 HW/SW (2bit ex. BBG008) + CTI_PORT_TYPE_MAX, +}; + +#define CTI_PORT_TYPE_VALID(_port_type) \ + (((_port_type) > CTI_PORT_TYPE_NONE) && \ + ((_port_type) < CTI_PORT_TYPE_MAX)) + +#define CTI_PORT_TYPE_RS485(_port_type) \ + (((_port_type) > CTI_PORT_TYPE_RS232) && \ + ((_port_type) < CTI_PORT_TYPE_MAX)) + struct exar8250; struct exar8250_platform { int (*rs485_config)(struct uart_port *port, struct ktermios *termios, struct serial_rs485 *rs485); const struct serial_rs485 *rs485_supported; - int (*register_gpio)(struct pci_dev *, struct uart_8250_port *); - void (*unregister_gpio)(struct uart_8250_port *); + int (*register_gpio)(struct pci_dev *pcidev, struct uart_8250_port *port); + void (*unregister_gpio)(struct uart_8250_port *port); }; /** * struct exar8250_board - board information * @num_ports: number of serial ports * @reg_shift: describes UART register mapping in PCI memory - * @setup: quirk run at ->probe() stage + * @setup: quirk run at ->probe() stage for each port * @exit: quirk run at ->remove() stage */ struct exar8250_board { unsigned int num_ports; unsigned int reg_shift; - int (*setup)(struct exar8250 *, struct pci_dev *, - struct uart_8250_port *, int); + int (*setup)(struct exar8250 *priv, struct pci_dev *pcidev, + struct uart_8250_port *port, int idx); void (*exit)(struct pci_dev *pcidev); }; struct exar8250 { unsigned int nr; + unsigned int osc_freq; struct exar8250_board *board; void __iomem *virt; int line[]; }; +static inline void exar_write_reg(struct exar8250 *priv, + unsigned int reg, u8 value) +{ + writeb(value, priv->virt + reg); +} + +static inline u8 exar_read_reg(struct exar8250 *priv, unsigned int reg) +{ + return readb(priv->virt + reg); +} + +static inline void exar_ee_select(struct exar8250 *priv) +{ + // Set chip select pin high to enable EEPROM reads/writes + exar_write_reg(priv, UART_EXAR_REGB, UART_EXAR_REGB_EECS); + // Min ~500ns delay needed between CS assert and EEPROM access + udelay(1); +} + +static inline void exar_ee_deselect(struct exar8250 *priv) +{ + exar_write_reg(priv, UART_EXAR_REGB, 0x00); +} + +static inline void exar_ee_write_bit(struct exar8250 *priv, u8 bit) +{ + u8 value = UART_EXAR_REGB_EECS; + + if (bit) + value |= UART_EXAR_REGB_EEDI; + + // Clock out the bit on the EEPROM interface + exar_write_reg(priv, UART_EXAR_REGB, value); + // 2us delay = ~500khz clock speed + udelay(2); + + value |= UART_EXAR_REGB_EECK; + + exar_write_reg(priv, UART_EXAR_REGB, value); + udelay(2); +} + +static inline u8 exar_ee_read_bit(struct exar8250 *priv) +{ + u8 regb; + u8 value = UART_EXAR_REGB_EECS; + + // Clock in the bit on the EEPROM interface + exar_write_reg(priv, UART_EXAR_REGB, value); + // 2us delay = ~500khz clock speed + udelay(2); + + value |= UART_EXAR_REGB_EECK; + + exar_write_reg(priv, UART_EXAR_REGB, value); + udelay(2); + + regb = exar_read_reg(priv, UART_EXAR_REGB); + + return (regb & UART_EXAR_REGB_EEDO ? 1 : 0); +} + +/** + * exar_ee_read() - Read a word from the EEPROM + * @priv: Device's private structure + * @ee_addr: Offset of EEPROM to read word from + * + * Read a single 16bit word from an Exar UART's EEPROM. + * The type of the EEPROM is AT93C46D. + * + * Return: EEPROM word + */ +static u16 exar_ee_read(struct exar8250 *priv, u8 ee_addr) +{ + int i; + u16 data = 0; + + exar_ee_select(priv); + + // Send read command (opcode 110) + exar_ee_write_bit(priv, 1); + exar_ee_write_bit(priv, 1); + exar_ee_write_bit(priv, 0); + + // Send address to read from + for (i = UART_EXAR_REGB_EE_ADDR_SIZE - 1; i >= 0; i--) + exar_ee_write_bit(priv, ee_addr & BIT(i)); + + // Read data 1 bit at a time starting with a dummy bit + for (i = UART_EXAR_REGB_EE_DATA_SIZE; i >= 0; i--) { + if (exar_ee_read_bit(priv)) + data |= BIT(i); + } + + exar_ee_deselect(priv); + + return data; +} + +/** + * exar_mpio_config_output() - Configure an Exar MPIO as an output + * @priv: Device's private structure + * @mpio_num: MPIO number/offset to configure + * + * Configure a single MPIO as an output and disable tristate. It is reccomended + * to set the level with exar_mpio_set_high()/exar_mpio_set_low() prior to + * calling this function to ensure default MPIO pin state. + * + * Return: 0 on success, negative error code on failure + */ +static int exar_mpio_config_output(struct exar8250 *priv, + unsigned int mpio_num) +{ + unsigned int mpio_offset; + u8 sel_reg; // MPIO Select register (input/output) + u8 tri_reg; // MPIO Tristate register + u8 value; + + if (mpio_num < 8) { + sel_reg = UART_EXAR_MPIOSEL_7_0; + tri_reg = UART_EXAR_MPIO3T_7_0; + mpio_offset = mpio_num; + } else if (mpio_num >= 8 && mpio_num < 16) { + sel_reg = UART_EXAR_MPIOSEL_15_8; + tri_reg = UART_EXAR_MPIO3T_15_8; + mpio_offset = mpio_num - 8; + } else { + return -EINVAL; + } + + // Disable MPIO pin tri-state + value = exar_read_reg(priv, tri_reg); + value &= ~BIT(mpio_offset); + exar_write_reg(priv, tri_reg, value); + + value = exar_read_reg(priv, sel_reg); + value &= ~BIT(mpio_offset); + exar_write_reg(priv, sel_reg, value); + + return 0; +} + +/** + * _exar_mpio_set() - Set an Exar MPIO output high or low + * @priv: Device's private structure + * @mpio_num: MPIO number/offset to set + * @high: Set MPIO high if true, low if false + * + * Set a single MPIO high or low. exar_mpio_config_output() must also be called + * to configure the pin as an output. + * + * Return: 0 on success, negative error code on failure + */ +static int _exar_mpio_set(struct exar8250 *priv, + unsigned int mpio_num, bool high) +{ + unsigned int mpio_offset; + u8 lvl_reg; + u8 value; + + if (mpio_num < 8) { + lvl_reg = UART_EXAR_MPIOLVL_7_0; + mpio_offset = mpio_num; + } else if (mpio_num >= 8 && mpio_num < 16) { + lvl_reg = UART_EXAR_MPIOLVL_15_8; + mpio_offset = mpio_num - 8; + } else { + return -EINVAL; + } + + value = exar_read_reg(priv, lvl_reg); + if (high) + value |= BIT(mpio_offset); + else + value &= ~BIT(mpio_offset); + exar_write_reg(priv, lvl_reg, value); + + return 0; +} + +static int exar_mpio_set_low(struct exar8250 *priv, unsigned int mpio_num) +{ + return _exar_mpio_set(priv, mpio_num, false); +} + +static int exar_mpio_set_high(struct exar8250 *priv, unsigned int mpio_num) +{ + return _exar_mpio_set(priv, mpio_num, true); +} + +static int generic_rs485_config(struct uart_port *port, struct ktermios *termios, + struct serial_rs485 *rs485) +{ + bool is_rs485 = !!(rs485->flags & SER_RS485_ENABLED); + u8 __iomem *p = port->membase; + u8 value; + + value = readb(p + UART_EXAR_FCTR); + if (is_rs485) + value |= UART_FCTR_EXAR_485; + else + value &= ~UART_FCTR_EXAR_485; + + writeb(value, p + UART_EXAR_FCTR); + + if (is_rs485) + writeb(UART_EXAR_RS485_DLY(4), p + UART_MSR); + + return 0; +} + +static const struct serial_rs485 generic_rs485_supported = { + .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND, +}; + static void exar_pm(struct uart_port *port, unsigned int state, unsigned int old) { /* @@ -256,7 +532,7 @@ static void exar_shutdown(struct uart_port *port) { bool tx_complete = false; struct uart_8250_port *up = up_to_u8250p(port); - struct circ_buf *xmit = &port->state->xmit; + struct tty_port *tport = &port->state->port; int i = 0; u16 lsr; @@ -267,7 +543,8 @@ static void exar_shutdown(struct uart_port *port) else tx_complete = false; usleep_range(1000, 1100); - } while (!uart_circ_empty(xmit) && !tx_complete && i++ < 1000); + } while (!kfifo_is_empty(&tport->xmit_fifo) && + !tx_complete && i++ < 1000); serial8250_do_shutdown(port); } @@ -331,41 +608,546 @@ pci_fastcom335_setup(struct exar8250 *priv, struct pci_dev *pcidev, writeb(32, p + UART_EXAR_TXTRG); writeb(32, p + UART_EXAR_RXTRG); + /* Skip the initial (per device) setup */ + if (idx) + return 0; + /* * Setup Multipurpose Input/Output pins. */ + switch (pcidev->device) { + case PCI_DEVICE_ID_COMMTECH_4222PCI335: + case PCI_DEVICE_ID_COMMTECH_4224PCI335: + writeb(0x78, p + UART_EXAR_MPIOLVL_7_0); + writeb(0x00, p + UART_EXAR_MPIOINV_7_0); + writeb(0x00, p + UART_EXAR_MPIOSEL_7_0); + break; + case PCI_DEVICE_ID_COMMTECH_2324PCI335: + case PCI_DEVICE_ID_COMMTECH_2328PCI335: + writeb(0x00, p + UART_EXAR_MPIOLVL_7_0); + writeb(0xc0, p + UART_EXAR_MPIOINV_7_0); + writeb(0xc0, p + UART_EXAR_MPIOSEL_7_0); + break; + default: + break; + } + writeb(0x00, p + UART_EXAR_MPIOINT_7_0); + writeb(0x00, p + UART_EXAR_MPIO3T_7_0); + writeb(0x00, p + UART_EXAR_MPIOOD_7_0); + + return 0; +} + +/** + * cti_tristate_disable() - Disable RS485 transciever tristate + * @priv: Device's private structure + * @port_num: Port number to set tristate off + * + * Most RS485 capable cards have a power on tristate jumper/switch that ensures + * the RS422/RS485 transceiver does not drive a multi-drop RS485 bus when it is + * not the master. When this jumper is installed the user must set the RS485 + * mode to Full or Half duplex to disable tristate prior to using the port. + * + * Some Exar UARTs have an auto-tristate feature while others require setting + * an MPIO to disable the tristate. + * + * Return: 0 on success, negative error code on failure + */ +static int cti_tristate_disable(struct exar8250 *priv, unsigned int port_num) +{ + int ret; + + ret = exar_mpio_set_high(priv, port_num); + if (ret) + return ret; + + return exar_mpio_config_output(priv, port_num); +} + +/** + * cti_plx_int_enable() - Enable UART interrupts to PLX bridge + * @priv: Device's private structure + * + * Some older CTI cards require MPIO_0 to be set low to enable the + * interrupts from the UART to the PLX PCI->PCIe bridge. + * + * Return: 0 on success, negative error code on failure + */ +static int cti_plx_int_enable(struct exar8250 *priv) +{ + int ret; + + ret = exar_mpio_set_low(priv, 0); + if (ret) + return ret; + + return exar_mpio_config_output(priv, 0); +} + +/** + * cti_read_osc_freq() - Read the UART oscillator frequency from EEPROM + * @priv: Device's private structure + * @eeprom_offset: Offset where the oscillator frequency is stored + * + * CTI XR17x15X and XR17V25X cards have the serial boards oscillator frequency + * stored in the EEPROM. FPGA and XR17V35X based cards use the PCI/PCIe clock. + * + * Return: frequency on success, negative error code on failure + */ +static int cti_read_osc_freq(struct exar8250 *priv, u8 eeprom_offset) +{ + u16 lower_word; + u16 upper_word; + + lower_word = exar_ee_read(priv, eeprom_offset); + // Check if EEPROM word was blank + if (lower_word == 0xFFFF) + return -EIO; + + upper_word = exar_ee_read(priv, (eeprom_offset + 1)); + if (upper_word == 0xFFFF) + return -EIO; + + return FIELD_PREP(CTI_EE_MASK_OSC_FREQ_LOWER, lower_word) | + FIELD_PREP(CTI_EE_MASK_OSC_FREQ_UPPER, upper_word); +} + +/** + * cti_get_port_type_xr17c15x_xr17v25x() - Get port type of xr17c15x/xr17v25x + * @priv: Device's private structure + * @pcidev: Pointer to the PCI device for this port + * @port_num: Port to get type of + * + * CTI xr17c15x and xr17v25x based cards port types are based on PCI IDs. + * + * Return: port type on success, CTI_PORT_TYPE_NONE on failure + */ +static enum cti_port_type cti_get_port_type_xr17c15x_xr17v25x(struct exar8250 *priv, + struct pci_dev *pcidev, + unsigned int port_num) +{ + switch (pcidev->subsystem_device) { + // RS232 only cards + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_232: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_232: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_232: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP_232: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP_232_NS: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP_232: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP_232_NS: + return CTI_PORT_TYPE_RS232; + // 1x RS232, 1x RS422/RS485 + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_1_1: + return (port_num == 0) ? CTI_PORT_TYPE_RS232 : CTI_PORT_TYPE_RS422_485; + // 2x RS232, 2x RS422/RS485 + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_2: + return (port_num < 2) ? CTI_PORT_TYPE_RS232 : CTI_PORT_TYPE_RS422_485; + // 4x RS232, 4x RS422/RS485 + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4_SP: + return (port_num < 4) ? CTI_PORT_TYPE_RS232 : CTI_PORT_TYPE_RS422_485; + // RS232/RS422/RS485 HW (jumper) selectable + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_SP_OPTO: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_SP_OPTO_A: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_SP_OPTO_B: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XPRS: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_A: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_B: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_16_XPRS_A: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_16_XPRS_B: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XPRS_OPTO: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_OPTO_A: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_OPTO_B: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XP_OPTO_LEFT: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XP_OPTO_RIGHT: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XP_OPTO: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4_XPRS_OPTO: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP: + return CTI_PORT_TYPE_RS232_422_485_HW; + // RS422/RS485 HW (jumper) selectable + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_485: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_485: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_485: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP_485: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP_485: + return CTI_PORT_TYPE_RS422_485; + // 6x RS232, 2x RS422/RS485 + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_6_2_SP: + return (port_num < 6) ? CTI_PORT_TYPE_RS232 : CTI_PORT_TYPE_RS422_485; + // 2x RS232, 6x RS422/RS485 + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_6_SP: + return (port_num < 2) ? CTI_PORT_TYPE_RS232 : CTI_PORT_TYPE_RS422_485; + default: + dev_err(&pcidev->dev, "unknown/unsupported device\n"); + return CTI_PORT_TYPE_NONE; + } +} + +/** + * cti_get_port_type_fpga() - Get the port type of a CTI FPGA card + * @priv: Device's private structure + * @pcidev: Pointer to the PCI device for this port + * @port_num: Port to get type of + * + * FPGA based cards port types are based on PCI IDs. + * + * Return: port type on success, CTI_PORT_TYPE_NONE on failure + */ +static enum cti_port_type cti_get_port_type_fpga(struct exar8250 *priv, + struct pci_dev *pcidev, + unsigned int port_num) +{ + switch (pcidev->device) { + case PCI_DEVICE_ID_CONNECT_TECH_PCI_XR79X_12_XIG00X: + case PCI_DEVICE_ID_CONNECT_TECH_PCI_XR79X_12_XIG01X: + case PCI_DEVICE_ID_CONNECT_TECH_PCI_XR79X_16: + return CTI_PORT_TYPE_RS232_422_485_HW; + default: + dev_err(&pcidev->dev, "unknown/unsupported device\n"); + return CTI_PORT_TYPE_NONE; + } +} + +/** + * cti_get_port_type_xr17v35x() - Read port type from the EEPROM + * @priv: Device's private structure + * @pcidev: Pointer to the PCI device for this port + * @port_num: port offset + * + * CTI XR17V35X based cards have the port types stored in the EEPROM. + * This function reads the port type for a single port. + * + * Return: port type on success, CTI_PORT_TYPE_NONE on failure + */ +static enum cti_port_type cti_get_port_type_xr17v35x(struct exar8250 *priv, + struct pci_dev *pcidev, + unsigned int port_num) +{ + enum cti_port_type port_type; + u16 port_flags; + u8 offset; + + offset = CTI_EE_OFF_XR17V35X_PORT_FLAGS + port_num; + port_flags = exar_ee_read(priv, offset); + + port_type = FIELD_GET(CTI_EE_MASK_PORT_FLAGS_TYPE, port_flags); + if (CTI_PORT_TYPE_VALID(port_type)) + return port_type; + + /* + * If the port type is missing the card assume it is a + * RS232/RS422/RS485 card to be safe. + * + * There is one known board (BEG013) that only has 3 of 4 port types + * written to the EEPROM so this acts as a work around. + */ + dev_warn(&pcidev->dev, "failed to get port %d type from EEPROM\n", port_num); + + return CTI_PORT_TYPE_RS232_422_485_HW; +} + +static int cti_rs485_config_mpio_tristate(struct uart_port *port, + struct ktermios *termios, + struct serial_rs485 *rs485) +{ + struct exar8250 *priv = (struct exar8250 *)port->private_data; + int ret; + + ret = generic_rs485_config(port, termios, rs485); + if (ret) + return ret; + + // Disable power-on RS485 tri-state via MPIO + return cti_tristate_disable(priv, port->port_id); +} + +static void cti_board_init_osc_freq(struct exar8250 *priv, struct pci_dev *pcidev, u8 eeprom_offset) +{ + int osc_freq; + + osc_freq = cti_read_osc_freq(priv, eeprom_offset); + if (osc_freq <= 0) { + dev_warn(&pcidev->dev, "failed to read OSC freq from EEPROM, using default\n"); + osc_freq = CTI_DEFAULT_PCI_OSC_FREQ; + } + + priv->osc_freq = osc_freq; +} + +static int cti_port_setup_common(struct exar8250 *priv, + struct pci_dev *pcidev, + int idx, unsigned int offset, + struct uart_8250_port *port) +{ + int ret; + + port->port.port_id = idx; + port->port.uartclk = priv->osc_freq; + + ret = serial8250_pci_setup_port(pcidev, port, 0, offset, 0); + if (ret) + return ret; + + port->port.private_data = (void *)priv; + port->port.pm = exar_pm; + port->port.shutdown = exar_shutdown; + + return 0; +} + +static int cti_board_init_fpga(struct exar8250 *priv, struct pci_dev *pcidev) +{ + int ret; + u16 cfg_val; + + // FPGA OSC is fixed to the 33MHz PCI clock + priv->osc_freq = CTI_DEFAULT_FPGA_OSC_FREQ; + + // Enable external interrupts in special cfg space register + ret = pci_read_config_word(pcidev, CTI_FPGA_CFG_INT_EN_REG, &cfg_val); + if (ret) + return pcibios_err_to_errno(ret); + + cfg_val |= CTI_FPGA_CFG_INT_EN_EXT_BIT; + ret = pci_write_config_word(pcidev, CTI_FPGA_CFG_INT_EN_REG, cfg_val); + if (ret) + return pcibios_err_to_errno(ret); + + // RS485 gate needs to be enabled; otherwise RTS/CTS will not work + exar_write_reg(priv, CTI_FPGA_RS485_IO_REG, 0x01); + + return 0; +} + +static int cti_port_setup_fpga(struct exar8250 *priv, + struct pci_dev *pcidev, + struct uart_8250_port *port, + int idx) +{ + enum cti_port_type port_type; + unsigned int offset; + int ret; + if (idx == 0) { - switch (pcidev->device) { - case PCI_DEVICE_ID_COMMTECH_4222PCI335: - case PCI_DEVICE_ID_COMMTECH_4224PCI335: - writeb(0x78, p + UART_EXAR_MPIOLVL_7_0); - writeb(0x00, p + UART_EXAR_MPIOINV_7_0); - writeb(0x00, p + UART_EXAR_MPIOSEL_7_0); + ret = cti_board_init_fpga(priv, pcidev); + if (ret) + return ret; + } + + port_type = cti_get_port_type_fpga(priv, pcidev, idx); + + // FPGA shares port offsets with XR17C15X + offset = idx * UART_EXAR_XR17C15X_PORT_OFFSET; + port->port.type = PORT_XR17D15X; + + port->port.get_divisor = xr17v35x_get_divisor; + port->port.set_divisor = xr17v35x_set_divisor; + port->port.startup = xr17v35x_startup; + + if (CTI_PORT_TYPE_RS485(port_type)) { + port->port.rs485_config = generic_rs485_config; + port->port.rs485_supported = generic_rs485_supported; + } + + return cti_port_setup_common(priv, pcidev, idx, offset, port); +} + +static void cti_board_init_xr17v35x(struct exar8250 *priv, struct pci_dev *pcidev) +{ + // XR17V35X uses the PCIe clock rather than an oscillator + priv->osc_freq = CTI_DEFAULT_PCIE_OSC_FREQ; +} + +static int cti_port_setup_xr17v35x(struct exar8250 *priv, + struct pci_dev *pcidev, + struct uart_8250_port *port, + int idx) +{ + enum cti_port_type port_type; + unsigned int offset; + int ret; + + if (idx == 0) + cti_board_init_xr17v35x(priv, pcidev); + + port_type = cti_get_port_type_xr17v35x(priv, pcidev, idx); + + offset = idx * UART_EXAR_XR17V35X_PORT_OFFSET; + port->port.type = PORT_XR17V35X; + + port->port.get_divisor = xr17v35x_get_divisor; + port->port.set_divisor = xr17v35x_set_divisor; + port->port.startup = xr17v35x_startup; + + switch (port_type) { + case CTI_PORT_TYPE_RS422_485: + case CTI_PORT_TYPE_RS232_422_485_HW: + port->port.rs485_config = cti_rs485_config_mpio_tristate; + port->port.rs485_supported = generic_rs485_supported; + break; + case CTI_PORT_TYPE_RS232_422_485_SW: + case CTI_PORT_TYPE_RS232_422_485_4B: + case CTI_PORT_TYPE_RS232_422_485_2B: + port->port.rs485_config = generic_rs485_config; + port->port.rs485_supported = generic_rs485_supported; + break; + default: + break; + } + + ret = cti_port_setup_common(priv, pcidev, idx, offset, port); + if (ret) + return ret; + + exar_write_reg(priv, (offset + UART_EXAR_8XMODE), 0x00); + exar_write_reg(priv, (offset + UART_EXAR_FCTR), UART_FCTR_EXAR_TRGD); + exar_write_reg(priv, (offset + UART_EXAR_TXTRG), 128); + exar_write_reg(priv, (offset + UART_EXAR_RXTRG), 128); + + return 0; +} + +static void cti_board_init_xr17v25x(struct exar8250 *priv, struct pci_dev *pcidev) +{ + cti_board_init_osc_freq(priv, pcidev, CTI_EE_OFF_XR17V25X_OSC_FREQ); + + /* enable interrupts on cards that need the "PLX fix" */ + switch (pcidev->subsystem_device) { + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_16_XPRS_A: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_16_XPRS_B: + cti_plx_int_enable(priv); + break; + default: + break; + } +} + +static int cti_port_setup_xr17v25x(struct exar8250 *priv, + struct pci_dev *pcidev, + struct uart_8250_port *port, + int idx) +{ + enum cti_port_type port_type; + unsigned int offset; + int ret; + + if (idx == 0) + cti_board_init_xr17v25x(priv, pcidev); + + port_type = cti_get_port_type_xr17c15x_xr17v25x(priv, pcidev, idx); + + offset = idx * UART_EXAR_XR17V25X_PORT_OFFSET; + port->port.type = PORT_XR17D15X; + + // XR17V25X supports fractional baudrates + port->port.get_divisor = xr17v35x_get_divisor; + port->port.set_divisor = xr17v35x_set_divisor; + port->port.startup = xr17v35x_startup; + + if (CTI_PORT_TYPE_RS485(port_type)) { + switch (pcidev->subsystem_device) { + // These cards support power on 485 tri-state via MPIO + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP_485: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4_SP: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_6_2_SP: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_6_SP: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XP_OPTO_LEFT: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XP_OPTO_RIGHT: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XP_OPTO: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4_XPRS_OPTO: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP_485: + port->port.rs485_config = cti_rs485_config_mpio_tristate; break; - case PCI_DEVICE_ID_COMMTECH_2324PCI335: - case PCI_DEVICE_ID_COMMTECH_2328PCI335: - writeb(0x00, p + UART_EXAR_MPIOLVL_7_0); - writeb(0xc0, p + UART_EXAR_MPIOINV_7_0); - writeb(0xc0, p + UART_EXAR_MPIOSEL_7_0); + // Otherwise auto or no power on 485 tri-state support + default: + port->port.rs485_config = generic_rs485_config; break; } - writeb(0x00, p + UART_EXAR_MPIOINT_7_0); - writeb(0x00, p + UART_EXAR_MPIO3T_7_0); - writeb(0x00, p + UART_EXAR_MPIOOD_7_0); + + port->port.rs485_supported = generic_rs485_supported; } + ret = cti_port_setup_common(priv, pcidev, idx, offset, port); + if (ret) + return ret; + + exar_write_reg(priv, (offset + UART_EXAR_8XMODE), 0x00); + exar_write_reg(priv, (offset + UART_EXAR_FCTR), UART_FCTR_EXAR_TRGD); + exar_write_reg(priv, (offset + UART_EXAR_TXTRG), 32); + exar_write_reg(priv, (offset + UART_EXAR_RXTRG), 32); + return 0; } -static int -pci_connect_tech_setup(struct exar8250 *priv, struct pci_dev *pcidev, - struct uart_8250_port *port, int idx) +static void cti_board_init_xr17c15x(struct exar8250 *priv, struct pci_dev *pcidev) { - unsigned int offset = idx * 0x200; - unsigned int baud = 1843200; + cti_board_init_osc_freq(priv, pcidev, CTI_EE_OFF_XR17C15X_OSC_FREQ); + + /* enable interrupts on cards that need the "PLX fix" */ + switch (pcidev->subsystem_device) { + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XPRS: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_A: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_B: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XPRS_OPTO: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_OPTO_A: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_OPTO_B: + cti_plx_int_enable(priv); + break; + default: + break; + } +} - port->port.uartclk = baud * 16; - return default_setup(priv, pcidev, idx, offset, port); +static int cti_port_setup_xr17c15x(struct exar8250 *priv, + struct pci_dev *pcidev, + struct uart_8250_port *port, + int idx) +{ + enum cti_port_type port_type; + unsigned int offset; + + if (idx == 0) + cti_board_init_xr17c15x(priv, pcidev); + + port_type = cti_get_port_type_xr17c15x_xr17v25x(priv, pcidev, idx); + + offset = idx * UART_EXAR_XR17C15X_PORT_OFFSET; + port->port.type = PORT_XR17D15X; + + if (CTI_PORT_TYPE_RS485(port_type)) { + switch (pcidev->subsystem_device) { + // These cards support power on 485 tri-state via MPIO + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP_485: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4_SP: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_6_2_SP: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_6_SP: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XP_OPTO_LEFT: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XP_OPTO_RIGHT: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XP_OPTO: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4_XPRS_OPTO: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP: + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP_485: + port->port.rs485_config = cti_rs485_config_mpio_tristate; + break; + // Otherwise auto or no power on 485 tri-state support + default: + port->port.rs485_config = generic_rs485_config; + break; + } + + port->port.rs485_supported = generic_rs485_supported; + } + + return cti_port_setup_common(priv, pcidev, idx, offset, port); } static int @@ -386,11 +1168,10 @@ static void setup_gpio(struct pci_dev *pcidev, u8 __iomem *p) * devices will export them as GPIOs, so we pre-configure them safely * as inputs. */ - u8 dir = 0x00; if ((pcidev->vendor == PCI_VENDOR_ID_EXAR) && - (pcidev->subsystem_vendor != PCI_VENDOR_ID_SEALEVEL)) { + (pcidev->subsystem_vendor != PCI_VENDOR_ID_SEALEVEL)) { // Configure GPIO as inputs for Commtech adapters dir = 0xff; } else { @@ -467,27 +1248,6 @@ static void xr17v35x_unregister_gpio(struct uart_8250_port *port) port->port.private_data = NULL; } -static int generic_rs485_config(struct uart_port *port, struct ktermios *termios, - struct serial_rs485 *rs485) -{ - bool is_rs485 = !!(rs485->flags & SER_RS485_ENABLED); - u8 __iomem *p = port->membase; - u8 value; - - value = readb(p + UART_EXAR_FCTR); - if (is_rs485) - value |= UART_FCTR_EXAR_485; - else - value &= ~UART_FCTR_EXAR_485; - - writeb(value, p + UART_EXAR_FCTR); - - if (is_rs485) - writeb(UART_EXAR_RS485_DLY(4), p + UART_MSR); - - return 0; -} - static int sealevel_rs485_config(struct uart_port *port, struct ktermios *termios, struct serial_rs485 *rs485) { @@ -501,35 +1261,32 @@ static int sealevel_rs485_config(struct uart_port *port, struct ktermios *termio if (ret) return ret; - if (rs485->flags & SER_RS485_ENABLED) { - old_lcr = readb(p + UART_LCR); + if (!(rs485->flags & SER_RS485_ENABLED)) + return 0; - /* Set EFR[4]=1 to enable enhanced feature registers */ - efr = readb(p + UART_XR_EFR); - efr |= UART_EFR_ECB; - writeb(efr, p + UART_XR_EFR); + old_lcr = readb(p + UART_LCR); - /* Set MCR to use DTR as Auto-RS485 Enable signal */ - writeb(UART_MCR_OUT1, p + UART_MCR); + /* Set EFR[4]=1 to enable enhanced feature registers */ + efr = readb(p + UART_XR_EFR); + efr |= UART_EFR_ECB; + writeb(efr, p + UART_XR_EFR); - /* Set LCR[7]=1 to enable access to DLD register */ - writeb(old_lcr | UART_LCR_DLAB, p + UART_LCR); + /* Set MCR to use DTR as Auto-RS485 Enable signal */ + writeb(UART_MCR_OUT1, p + UART_MCR); - /* Set DLD[7]=1 for inverted RS485 Enable logic */ - dld = readb(p + UART_EXAR_DLD); - dld |= UART_EXAR_DLD_485_POLARITY; - writeb(dld, p + UART_EXAR_DLD); + /* Set LCR[7]=1 to enable access to DLD register */ + writeb(old_lcr | UART_LCR_DLAB, p + UART_LCR); - writeb(old_lcr, p + UART_LCR); - } + /* Set DLD[7]=1 for inverted RS485 Enable logic */ + dld = readb(p + UART_EXAR_DLD); + dld |= UART_EXAR_DLD_485_POLARITY; + writeb(dld, p + UART_EXAR_DLD); + + writeb(old_lcr, p + UART_LCR); return 0; } -static const struct serial_rs485 generic_rs485_supported = { - .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND, -}; - static const struct exar8250_platform exar8250_default_platform = { .register_gpio = xr17v35x_register_gpio, .unregister_gpio = xr17v35x_unregister_gpio, @@ -714,6 +1471,35 @@ static irqreturn_t exar_misc_handler(int irq, void *data) return IRQ_HANDLED; } +static unsigned int exar_get_nr_ports(struct exar8250_board *board, struct pci_dev *pcidev) +{ + if (pcidev->vendor == PCI_VENDOR_ID_ACCESSIO) + return BIT(((pcidev->device & 0x38) >> 3) - 1); + + // Check if board struct overrides number of ports + if (board->num_ports > 0) + return board->num_ports; + + // Exar encodes # ports in last nibble of PCI Device ID ex. 0358 + if (pcidev->vendor == PCI_VENDOR_ID_EXAR) + return pcidev->device & 0x0f; + + // Handle CTI FPGA cards + if (pcidev->vendor == PCI_VENDOR_ID_CONNECT_TECH) { + switch (pcidev->device) { + case PCI_DEVICE_ID_CONNECT_TECH_PCI_XR79X_12_XIG00X: + case PCI_DEVICE_ID_CONNECT_TECH_PCI_XR79X_12_XIG01X: + return 12; + case PCI_DEVICE_ID_CONNECT_TECH_PCI_XR79X_16: + return 16; + default: + return 0; + } + } + + return 0; +} + static int exar_pci_probe(struct pci_dev *pcidev, const struct pci_device_id *ent) { @@ -733,12 +1519,9 @@ exar_pci_probe(struct pci_dev *pcidev, const struct pci_device_id *ent) maxnr = pci_resource_len(pcidev, bar) >> (board->reg_shift + 3); - if (pcidev->vendor == PCI_VENDOR_ID_ACCESSIO) - nr_ports = BIT(((pcidev->device & 0x38) >> 3) - 1); - else if (board->num_ports) - nr_ports = board->num_ports; - else - nr_ports = pcidev->device & 0x0f; + nr_ports = exar_get_nr_ports(board, pcidev); + if (nr_ports == 0) + return dev_err_probe(&pcidev->dev, -ENODEV, "failed to get number of ports\n"); priv = devm_kzalloc(&pcidev->dev, struct_size(priv, line, nr_ports), GFP_KERNEL); if (!priv) @@ -771,7 +1554,7 @@ exar_pci_probe(struct pci_dev *pcidev, const struct pci_device_id *ent) for (i = 0; i < nr_ports && i < maxnr; i++) { rc = board->setup(priv, pcidev, &uart, i); if (rc) { - dev_err(&pcidev->dev, "Failed to setup port %u\n", i); + dev_err_probe(&pcidev->dev, rc, "Failed to setup port %u\n", i); break; } @@ -780,10 +1563,9 @@ exar_pci_probe(struct pci_dev *pcidev, const struct pci_device_id *ent) priv->line[i] = serial8250_register_8250_port(&uart); if (priv->line[i] < 0) { - dev_err(&pcidev->dev, - "Couldn't register serial port %lx, irq %d, type %d, error %d\n", - uart.port.iobase, uart.port.irq, - uart.port.iotype, priv->line[i]); + dev_err_probe(&pcidev->dev, priv->line[i], + "Couldn't register serial port %lx, type %d, irq %d\n", + uart.port.iobase, uart.port.iotype, uart.port.irq); break; } } @@ -848,8 +1630,20 @@ static const struct exar8250_board pbn_fastcom335_8 = { .setup = pci_fastcom335_setup, }; -static const struct exar8250_board pbn_connect = { - .setup = pci_connect_tech_setup, +static const struct exar8250_board pbn_cti_xr17c15x = { + .setup = cti_port_setup_xr17c15x, +}; + +static const struct exar8250_board pbn_cti_xr17v25x = { + .setup = cti_port_setup_xr17v25x, +}; + +static const struct exar8250_board pbn_cti_xr17v35x = { + .setup = cti_port_setup_xr17v35x, +}; + +static const struct exar8250_board pbn_cti_fpga = { + .setup = cti_port_setup_fpga, }; static const struct exar8250_board pbn_exar_ibm_saturn = { @@ -896,13 +1690,13 @@ static const struct exar8250_board pbn_exar_XR17V8358 = { .exit = pci_xr17v35x_exit, }; -#define CONNECT_DEVICE(devid, sdevid, bd) { \ - PCI_DEVICE_SUB( \ - PCI_VENDOR_ID_EXAR, \ - PCI_DEVICE_ID_EXAR_##devid, \ - PCI_SUBVENDOR_ID_CONNECT_TECH, \ - PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_##sdevid), 0, 0, \ - (kernel_ulong_t)&bd \ +#define CTI_EXAR_DEVICE(devid, bd) { \ + PCI_DEVICE_SUB( \ + PCI_VENDOR_ID_EXAR, \ + PCI_DEVICE_ID_EXAR_##devid, \ + PCI_SUBVENDOR_ID_CONNECT_TECH, \ + PCI_ANY_ID), 0, 0, \ + (kernel_ulong_t)&bd \ } #define EXAR_DEVICE(vend, devid, bd) { PCI_DEVICE_DATA(vend, devid, &bd) } @@ -911,7 +1705,7 @@ static const struct exar8250_board pbn_exar_XR17V8358 = { PCI_DEVICE_SUB( \ PCI_VENDOR_ID_EXAR, \ PCI_DEVICE_ID_EXAR_##devid, \ - PCI_VENDOR_ID_IBM, \ + PCI_SUBVENDOR_ID_IBM, \ PCI_SUBDEVICE_ID_IBM_##sdevid), 0, 0, \ (kernel_ulong_t)&bd \ } @@ -934,18 +1728,23 @@ static const struct pci_device_id exar_pci_tbl[] = { EXAR_DEVICE(ACCESSIO, COM_4SM, pbn_exar_XR17C15x), EXAR_DEVICE(ACCESSIO, COM_8SM, pbn_exar_XR17C15x), - CONNECT_DEVICE(XR17C152, UART_2_232, pbn_connect), - CONNECT_DEVICE(XR17C154, UART_4_232, pbn_connect), - CONNECT_DEVICE(XR17C158, UART_8_232, pbn_connect), - CONNECT_DEVICE(XR17C152, UART_1_1, pbn_connect), - CONNECT_DEVICE(XR17C154, UART_2_2, pbn_connect), - CONNECT_DEVICE(XR17C158, UART_4_4, pbn_connect), - CONNECT_DEVICE(XR17C152, UART_2, pbn_connect), - CONNECT_DEVICE(XR17C154, UART_4, pbn_connect), - CONNECT_DEVICE(XR17C158, UART_8, pbn_connect), - CONNECT_DEVICE(XR17C152, UART_2_485, pbn_connect), - CONNECT_DEVICE(XR17C154, UART_4_485, pbn_connect), - CONNECT_DEVICE(XR17C158, UART_8_485, pbn_connect), + /* Connect Tech cards with Exar vendor/device PCI IDs */ + CTI_EXAR_DEVICE(XR17C152, pbn_cti_xr17c15x), + CTI_EXAR_DEVICE(XR17C154, pbn_cti_xr17c15x), + CTI_EXAR_DEVICE(XR17C158, pbn_cti_xr17c15x), + + CTI_EXAR_DEVICE(XR17V252, pbn_cti_xr17v25x), + CTI_EXAR_DEVICE(XR17V254, pbn_cti_xr17v25x), + CTI_EXAR_DEVICE(XR17V258, pbn_cti_xr17v25x), + + CTI_EXAR_DEVICE(XR17V352, pbn_cti_xr17v35x), + CTI_EXAR_DEVICE(XR17V354, pbn_cti_xr17v35x), + CTI_EXAR_DEVICE(XR17V358, pbn_cti_xr17v35x), + + /* Connect Tech cards with Connect Tech vendor/device PCI IDs (FPGA based) */ + EXAR_DEVICE(CONNECT_TECH, PCI_XR79X_12_XIG00X, pbn_cti_fpga), + EXAR_DEVICE(CONNECT_TECH, PCI_XR79X_12_XIG01X, pbn_cti_fpga), + EXAR_DEVICE(CONNECT_TECH, PCI_XR79X_16, pbn_cti_fpga), IBM_DEVICE(XR17C152, SATURN_SERIAL_ONE_PORT, pbn_exar_ibm_saturn), -- cgit v1.2.3