From ace9429bb58fd418f0c81d4c2835699bddf6bde6 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Thu, 11 Apr 2024 10:27:49 +0200 Subject: Adding upstream version 6.6.15. Signed-off-by: Daniel Baumann --- drivers/w1/masters/Kconfig | 71 +++ drivers/w1/masters/Makefile | 13 + drivers/w1/masters/ds2482.c | 563 ++++++++++++++++++++ drivers/w1/masters/ds2490.c | 1113 ++++++++++++++++++++++++++++++++++++++++ drivers/w1/masters/matrox_w1.c | 202 ++++++++ drivers/w1/masters/mxc_w1.c | 183 +++++++ drivers/w1/masters/omap_hdq.c | 688 +++++++++++++++++++++++++ drivers/w1/masters/sgi_w1.c | 128 +++++ drivers/w1/masters/w1-gpio.c | 204 ++++++++ 9 files changed, 3165 insertions(+) create mode 100644 drivers/w1/masters/Kconfig create mode 100644 drivers/w1/masters/Makefile create mode 100644 drivers/w1/masters/ds2482.c create mode 100644 drivers/w1/masters/ds2490.c create mode 100644 drivers/w1/masters/matrox_w1.c create mode 100644 drivers/w1/masters/mxc_w1.c create mode 100644 drivers/w1/masters/omap_hdq.c create mode 100644 drivers/w1/masters/sgi_w1.c create mode 100644 drivers/w1/masters/w1-gpio.c (limited to 'drivers/w1/masters') diff --git a/drivers/w1/masters/Kconfig b/drivers/w1/masters/Kconfig new file mode 100644 index 0000000000..ad31657328 --- /dev/null +++ b/drivers/w1/masters/Kconfig @@ -0,0 +1,71 @@ +# SPDX-License-Identifier: GPL-2.0-only +# +# 1-wire bus master configuration +# + +menu "1-wire Bus Masters" + +config W1_MASTER_MATROX + tristate "Matrox G400 transport layer for 1-wire" + depends on PCI + help + Say Y here if you want to communicate with your 1-wire devices + using Matrox's G400 GPIO pins. + + This support is also available as a module. If so, the module + will be called matrox_w1. + +config W1_MASTER_DS2490 + tristate "DS2490 USB <-> W1 transport layer for 1-wire" + depends on USB + help + Say Y here if you want to have a driver for DS2490 based USB <-> W1 bridges, + for example DS9490*. + + This support is also available as a module. If so, the module + will be called ds2490. + +config W1_MASTER_DS2482 + tristate "Maxim DS2482 I2C to 1-Wire bridge" + depends on I2C + help + If you say yes here you get support for the Maxim DS2482 + I2C to 1-Wire bridge. + + This driver can also be built as a module. If so, the module + will be called ds2482. + +config W1_MASTER_MXC + tristate "Freescale MXC 1-wire busmaster" + depends on ARCH_MXC || COMPILE_TEST + help + Say Y here to enable MXC 1-wire host + +config W1_MASTER_GPIO + tristate "GPIO 1-wire busmaster" + depends on GPIOLIB || COMPILE_TEST + help + Say Y here if you want to communicate with your 1-wire devices using + GPIO pins. This driver uses the GPIO API to control the wire. + + This support is also available as a module. If so, the module + will be called w1-gpio. + +config HDQ_MASTER_OMAP + tristate "OMAP HDQ driver" + depends on ARCH_OMAP || COMPILE_TEST + help + Say Y here if you want support for the 1-wire or HDQ Interface + on an OMAP processor. + +config W1_MASTER_SGI + tristate "SGI ASIC driver" + help + Say Y here if you want support for your 1-wire devices using + SGI ASIC 1-Wire interface + + This support is also available as a module. If so, the module + will be called sgi_w1. + +endmenu + diff --git a/drivers/w1/masters/Makefile b/drivers/w1/masters/Makefile new file mode 100644 index 0000000000..c5d85a827e --- /dev/null +++ b/drivers/w1/masters/Makefile @@ -0,0 +1,13 @@ +# SPDX-License-Identifier: GPL-2.0 +# +# Makefile for 1-wire bus master drivers. +# + +obj-$(CONFIG_W1_MASTER_MATROX) += matrox_w1.o +obj-$(CONFIG_W1_MASTER_DS2490) += ds2490.o +obj-$(CONFIG_W1_MASTER_DS2482) += ds2482.o +obj-$(CONFIG_W1_MASTER_MXC) += mxc_w1.o + +obj-$(CONFIG_W1_MASTER_GPIO) += w1-gpio.o +obj-$(CONFIG_HDQ_MASTER_OMAP) += omap_hdq.o +obj-$(CONFIG_W1_MASTER_SGI) += sgi_w1.o diff --git a/drivers/w1/masters/ds2482.c b/drivers/w1/masters/ds2482.c new file mode 100644 index 0000000000..b2d76c1784 --- /dev/null +++ b/drivers/w1/masters/ds2482.c @@ -0,0 +1,563 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * ds2482.c - provides i2c to w1-master bridge(s) + * Copyright (C) 2005 Ben Gardner + * + * The DS2482 is a sensor chip made by Dallas Semiconductor (Maxim). + * It is a I2C to 1-wire bridge. + * There are two variations: -100 and -800, which have 1 or 8 1-wire ports. + * The complete datasheet can be obtained from MAXIM's website at: + * http://www.maxim-ic.com/quick_view2.cfm/qv_pk/4382 + */ + +#include +#include +#include +#include +#include + +#include + +/* + * Allow the active pullup to be disabled, default is enabled. + * + * Note from the DS2482 datasheet: + * The APU bit controls whether an active pullup (controlled slew-rate + * transistor) or a passive pullup (Rwpu resistor) will be used to drive + * a 1-Wire line from low to high. When APU = 0, active pullup is disabled + * (resistor mode). Active Pullup should always be selected unless there is + * only a single slave on the 1-Wire line. + */ +static int ds2482_active_pullup = 1; +module_param_named(active_pullup, ds2482_active_pullup, int, 0644); +MODULE_PARM_DESC(active_pullup, "Active pullup (apply to all buses): " \ + "0-disable, 1-enable (default)"); + +/* extra configurations - e.g. 1WS */ +static int extra_config; +module_param(extra_config, int, 0644); +MODULE_PARM_DESC(extra_config, "Extra Configuration settings 1=APU,2=PPM,3=SPU,8=1WS"); + +/* + * The DS2482 registers - there are 3 registers that are addressed by a read + * pointer. The read pointer is set by the last command executed. + * + * To read the data, issue a register read for any address + */ +#define DS2482_CMD_RESET 0xF0 /* No param */ +#define DS2482_CMD_SET_READ_PTR 0xE1 /* Param: DS2482_PTR_CODE_xxx */ +#define DS2482_CMD_CHANNEL_SELECT 0xC3 /* Param: Channel byte - DS2482-800 only */ +#define DS2482_CMD_WRITE_CONFIG 0xD2 /* Param: Config byte */ +#define DS2482_CMD_1WIRE_RESET 0xB4 /* Param: None */ +#define DS2482_CMD_1WIRE_SINGLE_BIT 0x87 /* Param: Bit byte (bit7) */ +#define DS2482_CMD_1WIRE_WRITE_BYTE 0xA5 /* Param: Data byte */ +#define DS2482_CMD_1WIRE_READ_BYTE 0x96 /* Param: None */ +/* Note to read the byte, Set the ReadPtr to Data then read (any addr) */ +#define DS2482_CMD_1WIRE_TRIPLET 0x78 /* Param: Dir byte (bit7) */ + +/* Values for DS2482_CMD_SET_READ_PTR */ +#define DS2482_PTR_CODE_STATUS 0xF0 +#define DS2482_PTR_CODE_DATA 0xE1 +#define DS2482_PTR_CODE_CHANNEL 0xD2 /* DS2482-800 only */ +#define DS2482_PTR_CODE_CONFIG 0xC3 + +/* + * Configure Register bit definitions + * The top 4 bits always read 0. + * To write, the top nibble must be the 1's compl. of the low nibble. + */ +#define DS2482_REG_CFG_1WS 0x08 /* 1-wire speed */ +#define DS2482_REG_CFG_SPU 0x04 /* strong pull-up */ +#define DS2482_REG_CFG_PPM 0x02 /* presence pulse masking */ +#define DS2482_REG_CFG_APU 0x01 /* active pull-up */ + + +/* + * Write and verify codes for the CHANNEL_SELECT command (DS2482-800 only). + * To set the channel, write the value at the index of the channel. + * Read and compare against the corresponding value to verify the change. + */ +static const u8 ds2482_chan_wr[8] = { 0xF0, 0xE1, 0xD2, 0xC3, 0xB4, 0xA5, 0x96, 0x87 }; +static const u8 ds2482_chan_rd[8] = { 0xB8, 0xB1, 0xAA, 0xA3, 0x9C, 0x95, 0x8E, 0x87 }; + + +/* + * Status Register bit definitions (read only) + */ +#define DS2482_REG_STS_DIR 0x80 +#define DS2482_REG_STS_TSB 0x40 +#define DS2482_REG_STS_SBR 0x20 +#define DS2482_REG_STS_RST 0x10 +#define DS2482_REG_STS_LL 0x08 +#define DS2482_REG_STS_SD 0x04 +#define DS2482_REG_STS_PPD 0x02 +#define DS2482_REG_STS_1WB 0x01 + +/* + * Client data (each client gets its own) + */ + +struct ds2482_data; + +struct ds2482_w1_chan { + struct ds2482_data *pdev; + u8 channel; + struct w1_bus_master w1_bm; +}; + +struct ds2482_data { + struct i2c_client *client; + struct mutex access_lock; + + /* 1-wire interface(s) */ + int w1_count; /* 1 or 8 */ + struct ds2482_w1_chan w1_ch[8]; + + /* per-device values */ + u8 channel; + u8 read_prt; /* see DS2482_PTR_CODE_xxx */ + u8 reg_config; +}; + + +/** + * ds2482_calculate_config - Helper to calculate values for configuration register + * @conf: the raw config value + * Return: the value w/ complements that can be written to register + */ +static inline u8 ds2482_calculate_config(u8 conf) +{ + conf |= extra_config; + + if (ds2482_active_pullup) + conf |= DS2482_REG_CFG_APU; + + return conf | ((~conf & 0x0f) << 4); +} + + +/** + * ds2482_select_register - Sets the read pointer. + * @pdev: The ds2482 client pointer + * @read_ptr: see DS2482_PTR_CODE_xxx above + * Return: -1 on failure, 0 on success + */ +static inline int ds2482_select_register(struct ds2482_data *pdev, u8 read_ptr) +{ + if (pdev->read_prt != read_ptr) { + if (i2c_smbus_write_byte_data(pdev->client, + DS2482_CMD_SET_READ_PTR, + read_ptr) < 0) + return -1; + + pdev->read_prt = read_ptr; + } + return 0; +} + +/** + * ds2482_send_cmd - Sends a command without a parameter + * @pdev: The ds2482 client pointer + * @cmd: DS2482_CMD_RESET, + * DS2482_CMD_1WIRE_RESET, + * DS2482_CMD_1WIRE_READ_BYTE + * Return: -1 on failure, 0 on success + */ +static inline int ds2482_send_cmd(struct ds2482_data *pdev, u8 cmd) +{ + if (i2c_smbus_write_byte(pdev->client, cmd) < 0) + return -1; + + pdev->read_prt = DS2482_PTR_CODE_STATUS; + return 0; +} + +/** + * ds2482_send_cmd_data - Sends a command with a parameter + * @pdev: The ds2482 client pointer + * @cmd: DS2482_CMD_WRITE_CONFIG, + * DS2482_CMD_1WIRE_SINGLE_BIT, + * DS2482_CMD_1WIRE_WRITE_BYTE, + * DS2482_CMD_1WIRE_TRIPLET + * @byte: The data to send + * Return: -1 on failure, 0 on success + */ +static inline int ds2482_send_cmd_data(struct ds2482_data *pdev, + u8 cmd, u8 byte) +{ + if (i2c_smbus_write_byte_data(pdev->client, cmd, byte) < 0) + return -1; + + /* all cmds leave in STATUS, except CONFIG */ + pdev->read_prt = (cmd != DS2482_CMD_WRITE_CONFIG) ? + DS2482_PTR_CODE_STATUS : DS2482_PTR_CODE_CONFIG; + return 0; +} + + +/* + * 1-Wire interface code + */ + +#define DS2482_WAIT_IDLE_TIMEOUT 100 + +/** + * ds2482_wait_1wire_idle - Waits until the 1-wire interface is idle (not busy) + * + * @pdev: Pointer to the device structure + * Return: the last value read from status or -1 (failure) + */ +static int ds2482_wait_1wire_idle(struct ds2482_data *pdev) +{ + int temp = -1; + int retries = 0; + + if (!ds2482_select_register(pdev, DS2482_PTR_CODE_STATUS)) { + do { + temp = i2c_smbus_read_byte(pdev->client); + } while ((temp >= 0) && (temp & DS2482_REG_STS_1WB) && + (++retries < DS2482_WAIT_IDLE_TIMEOUT)); + } + + if (retries >= DS2482_WAIT_IDLE_TIMEOUT) + pr_err("%s: timeout on channel %d\n", + __func__, pdev->channel); + + return temp; +} + +/** + * ds2482_set_channel - Selects a w1 channel. + * The 1-wire interface must be idle before calling this function. + * + * @pdev: The ds2482 client pointer + * @channel: 0-7 + * Return: -1 (failure) or 0 (success) + */ +static int ds2482_set_channel(struct ds2482_data *pdev, u8 channel) +{ + if (i2c_smbus_write_byte_data(pdev->client, DS2482_CMD_CHANNEL_SELECT, + ds2482_chan_wr[channel]) < 0) + return -1; + + pdev->read_prt = DS2482_PTR_CODE_CHANNEL; + pdev->channel = -1; + if (i2c_smbus_read_byte(pdev->client) == ds2482_chan_rd[channel]) { + pdev->channel = channel; + return 0; + } + return -1; +} + + +/** + * ds2482_w1_touch_bit - Performs the touch-bit function, which writes a 0 or 1 and reads the level. + * + * @data: The ds2482 channel pointer + * @bit: The level to write: 0 or non-zero + * Return: The level read: 0 or 1 + */ +static u8 ds2482_w1_touch_bit(void *data, u8 bit) +{ + struct ds2482_w1_chan *pchan = data; + struct ds2482_data *pdev = pchan->pdev; + int status = -1; + + mutex_lock(&pdev->access_lock); + + /* Select the channel */ + ds2482_wait_1wire_idle(pdev); + if (pdev->w1_count > 1) + ds2482_set_channel(pdev, pchan->channel); + + /* Send the touch command, wait until 1WB == 0, return the status */ + if (!ds2482_send_cmd_data(pdev, DS2482_CMD_1WIRE_SINGLE_BIT, + bit ? 0xFF : 0)) + status = ds2482_wait_1wire_idle(pdev); + + mutex_unlock(&pdev->access_lock); + + return (status & DS2482_REG_STS_SBR) ? 1 : 0; +} + +/** + * ds2482_w1_triplet - Performs the triplet function, which reads two bits and writes a bit. + * The bit written is determined by the two reads: + * 00 => dbit, 01 => 0, 10 => 1 + * + * @data: The ds2482 channel pointer + * @dbit: The direction to choose if both branches are valid + * Return: b0=read1 b1=read2 b3=bit written + */ +static u8 ds2482_w1_triplet(void *data, u8 dbit) +{ + struct ds2482_w1_chan *pchan = data; + struct ds2482_data *pdev = pchan->pdev; + int status = (3 << 5); + + mutex_lock(&pdev->access_lock); + + /* Select the channel */ + ds2482_wait_1wire_idle(pdev); + if (pdev->w1_count > 1) + ds2482_set_channel(pdev, pchan->channel); + + /* Send the triplet command, wait until 1WB == 0, return the status */ + if (!ds2482_send_cmd_data(pdev, DS2482_CMD_1WIRE_TRIPLET, + dbit ? 0xFF : 0)) + status = ds2482_wait_1wire_idle(pdev); + + mutex_unlock(&pdev->access_lock); + + /* Decode the status */ + return (status >> 5); +} + +/** + * ds2482_w1_write_byte - Performs the write byte function. + * + * @data: The ds2482 channel pointer + * @byte: The value to write + */ +static void ds2482_w1_write_byte(void *data, u8 byte) +{ + struct ds2482_w1_chan *pchan = data; + struct ds2482_data *pdev = pchan->pdev; + + mutex_lock(&pdev->access_lock); + + /* Select the channel */ + ds2482_wait_1wire_idle(pdev); + if (pdev->w1_count > 1) + ds2482_set_channel(pdev, pchan->channel); + + /* Send the write byte command */ + ds2482_send_cmd_data(pdev, DS2482_CMD_1WIRE_WRITE_BYTE, byte); + + mutex_unlock(&pdev->access_lock); +} + +/** + * ds2482_w1_read_byte - Performs the read byte function. + * + * @data: The ds2482 channel pointer + * Return: The value read + */ +static u8 ds2482_w1_read_byte(void *data) +{ + struct ds2482_w1_chan *pchan = data; + struct ds2482_data *pdev = pchan->pdev; + int result; + + mutex_lock(&pdev->access_lock); + + /* Select the channel */ + ds2482_wait_1wire_idle(pdev); + if (pdev->w1_count > 1) + ds2482_set_channel(pdev, pchan->channel); + + /* Send the read byte command */ + ds2482_send_cmd(pdev, DS2482_CMD_1WIRE_READ_BYTE); + + /* Wait until 1WB == 0 */ + ds2482_wait_1wire_idle(pdev); + + /* Select the data register */ + ds2482_select_register(pdev, DS2482_PTR_CODE_DATA); + + /* Read the data byte */ + result = i2c_smbus_read_byte(pdev->client); + + mutex_unlock(&pdev->access_lock); + + return result; +} + + +/** + * ds2482_w1_reset_bus - Sends a reset on the 1-wire interface + * + * @data: The ds2482 channel pointer + * Return: 0=Device present, 1=No device present or error + */ +static u8 ds2482_w1_reset_bus(void *data) +{ + struct ds2482_w1_chan *pchan = data; + struct ds2482_data *pdev = pchan->pdev; + int err; + u8 retval = 1; + + mutex_lock(&pdev->access_lock); + + /* Select the channel */ + ds2482_wait_1wire_idle(pdev); + if (pdev->w1_count > 1) + ds2482_set_channel(pdev, pchan->channel); + + /* Send the reset command */ + err = ds2482_send_cmd(pdev, DS2482_CMD_1WIRE_RESET); + if (err >= 0) { + /* Wait until the reset is complete */ + err = ds2482_wait_1wire_idle(pdev); + retval = !(err & DS2482_REG_STS_PPD); + + /* If the chip did reset since detect, re-config it */ + if (err & DS2482_REG_STS_RST) + ds2482_send_cmd_data(pdev, DS2482_CMD_WRITE_CONFIG, + ds2482_calculate_config(0x00)); + } + + mutex_unlock(&pdev->access_lock); + + return retval; +} + +static u8 ds2482_w1_set_pullup(void *data, int delay) +{ + struct ds2482_w1_chan *pchan = data; + struct ds2482_data *pdev = pchan->pdev; + u8 retval = 1; + + /* if delay is non-zero activate the pullup, + * the strong pullup will be automatically deactivated + * by the master, so do not explicitly deactive it + */ + if (delay) { + /* both waits are crucial, otherwise devices might not be + * powered long enough, causing e.g. a w1_therm sensor to + * provide wrong conversion results + */ + ds2482_wait_1wire_idle(pdev); + /* note: it seems like both SPU and APU have to be set! */ + retval = ds2482_send_cmd_data(pdev, DS2482_CMD_WRITE_CONFIG, + ds2482_calculate_config(DS2482_REG_CFG_SPU | + DS2482_REG_CFG_APU)); + ds2482_wait_1wire_idle(pdev); + } + + return retval; +} + + +static int ds2482_probe(struct i2c_client *client) +{ + struct ds2482_data *data; + int err = -ENODEV; + int temp1; + int idx; + + if (!i2c_check_functionality(client->adapter, + I2C_FUNC_SMBUS_WRITE_BYTE_DATA | + I2C_FUNC_SMBUS_BYTE)) + return -ENODEV; + + data = kzalloc(sizeof(struct ds2482_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + data->client = client; + i2c_set_clientdata(client, data); + + /* Reset the device (sets the read_ptr to status) */ + if (ds2482_send_cmd(data, DS2482_CMD_RESET) < 0) { + dev_warn(&client->dev, "DS2482 reset failed.\n"); + goto exit_free; + } + + /* Sleep at least 525ns to allow the reset to complete */ + ndelay(525); + + /* Read the status byte - only reset bit and line should be set */ + temp1 = i2c_smbus_read_byte(client); + if (temp1 != (DS2482_REG_STS_LL | DS2482_REG_STS_RST)) { + dev_warn(&client->dev, "DS2482 reset status " + "0x%02X - not a DS2482\n", temp1); + goto exit_free; + } + + /* Detect the 8-port version */ + data->w1_count = 1; + if (ds2482_set_channel(data, 7) == 0) + data->w1_count = 8; + + /* Set all config items to 0 (off) */ + ds2482_send_cmd_data(data, DS2482_CMD_WRITE_CONFIG, + ds2482_calculate_config(0x00)); + + mutex_init(&data->access_lock); + + /* Register 1-wire interface(s) */ + for (idx = 0; idx < data->w1_count; idx++) { + data->w1_ch[idx].pdev = data; + data->w1_ch[idx].channel = idx; + + /* Populate all the w1 bus master stuff */ + data->w1_ch[idx].w1_bm.data = &data->w1_ch[idx]; + data->w1_ch[idx].w1_bm.read_byte = ds2482_w1_read_byte; + data->w1_ch[idx].w1_bm.write_byte = ds2482_w1_write_byte; + data->w1_ch[idx].w1_bm.touch_bit = ds2482_w1_touch_bit; + data->w1_ch[idx].w1_bm.triplet = ds2482_w1_triplet; + data->w1_ch[idx].w1_bm.reset_bus = ds2482_w1_reset_bus; + data->w1_ch[idx].w1_bm.set_pullup = ds2482_w1_set_pullup; + + err = w1_add_master_device(&data->w1_ch[idx].w1_bm); + if (err) { + data->w1_ch[idx].pdev = NULL; + goto exit_w1_remove; + } + } + + return 0; + +exit_w1_remove: + for (idx = 0; idx < data->w1_count; idx++) { + if (data->w1_ch[idx].pdev != NULL) + w1_remove_master_device(&data->w1_ch[idx].w1_bm); + } +exit_free: + kfree(data); +exit: + return err; +} + +static void ds2482_remove(struct i2c_client *client) +{ + struct ds2482_data *data = i2c_get_clientdata(client); + int idx; + + /* Unregister the 1-wire bridge(s) */ + for (idx = 0; idx < data->w1_count; idx++) { + if (data->w1_ch[idx].pdev != NULL) + w1_remove_master_device(&data->w1_ch[idx].w1_bm); + } + + /* Free the memory */ + kfree(data); +} + +/* + * Driver data (common to all clients) + */ +static const struct i2c_device_id ds2482_id[] = { + { "ds2482", 0 }, + { "ds2484", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, ds2482_id); + +static struct i2c_driver ds2482_driver = { + .driver = { + .name = "ds2482", + }, + .probe = ds2482_probe, + .remove = ds2482_remove, + .id_table = ds2482_id, +}; +module_i2c_driver(ds2482_driver); + +MODULE_AUTHOR("Ben Gardner "); +MODULE_DESCRIPTION("DS2482 driver"); + +MODULE_LICENSE("GPL"); diff --git a/drivers/w1/masters/ds2490.c b/drivers/w1/masters/ds2490.c new file mode 100644 index 0000000000..5f5b97e247 --- /dev/null +++ b/drivers/w1/masters/ds2490.c @@ -0,0 +1,1113 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * ds2490.c USB to one wire bridge + * + * Copyright (c) 2004 Evgeniy Polyakov + */ + +#include +#include +#include +#include +#include + +#include + +/* USB Standard */ +/* USB Control request vendor type */ +#define VENDOR 0x40 + +/* COMMAND TYPE CODES */ +#define CONTROL_CMD 0x00 +#define COMM_CMD 0x01 +#define MODE_CMD 0x02 + +/* CONTROL COMMAND CODES */ +#define CTL_RESET_DEVICE 0x0000 +#define CTL_START_EXE 0x0001 +#define CTL_RESUME_EXE 0x0002 +#define CTL_HALT_EXE_IDLE 0x0003 +#define CTL_HALT_EXE_DONE 0x0004 +#define CTL_FLUSH_COMM_CMDS 0x0007 +#define CTL_FLUSH_RCV_BUFFER 0x0008 +#define CTL_FLUSH_XMT_BUFFER 0x0009 +#define CTL_GET_COMM_CMDS 0x000A + +/* MODE COMMAND CODES */ +#define MOD_PULSE_EN 0x0000 +#define MOD_SPEED_CHANGE_EN 0x0001 +#define MOD_1WIRE_SPEED 0x0002 +#define MOD_STRONG_PU_DURATION 0x0003 +#define MOD_PULLDOWN_SLEWRATE 0x0004 +#define MOD_PROG_PULSE_DURATION 0x0005 +#define MOD_WRITE1_LOWTIME 0x0006 +#define MOD_DSOW0_TREC 0x0007 + +/* COMMUNICATION COMMAND CODES */ +#define COMM_ERROR_ESCAPE 0x0601 +#define COMM_SET_DURATION 0x0012 +#define COMM_BIT_IO 0x0020 +#define COMM_PULSE 0x0030 +#define COMM_1_WIRE_RESET 0x0042 +#define COMM_BYTE_IO 0x0052 +#define COMM_MATCH_ACCESS 0x0064 +#define COMM_BLOCK_IO 0x0074 +#define COMM_READ_STRAIGHT 0x0080 +#define COMM_DO_RELEASE 0x6092 +#define COMM_SET_PATH 0x00A2 +#define COMM_WRITE_SRAM_PAGE 0x00B2 +#define COMM_WRITE_EPROM 0x00C4 +#define COMM_READ_CRC_PROT_PAGE 0x00D4 +#define COMM_READ_REDIRECT_PAGE_CRC 0x21E4 +#define COMM_SEARCH_ACCESS 0x00F4 + +/* Communication command bits */ +#define COMM_TYPE 0x0008 +#define COMM_SE 0x0008 +#define COMM_D 0x0008 +#define COMM_Z 0x0008 +#define COMM_CH 0x0008 +#define COMM_SM 0x0008 +#define COMM_R 0x0008 +#define COMM_IM 0x0001 + +#define COMM_PS 0x4000 +#define COMM_PST 0x4000 +#define COMM_CIB 0x4000 +#define COMM_RTS 0x4000 +#define COMM_DT 0x2000 +#define COMM_SPU 0x1000 +#define COMM_F 0x0800 +#define COMM_NTF 0x0400 +#define COMM_ICP 0x0200 +#define COMM_RST 0x0100 + +#define PULSE_PROG 0x01 +#define PULSE_SPUE 0x02 + +#define BRANCH_MAIN 0xCC +#define BRANCH_AUX 0x33 + +/* Status flags */ +#define ST_SPUA 0x01 /* Strong Pull-up is active */ +#define ST_PRGA 0x02 /* 12V programming pulse is being generated */ +#define ST_12VP 0x04 /* external 12V programming voltage is present */ +#define ST_PMOD 0x08 /* DS2490 powered from USB and external sources */ +#define ST_HALT 0x10 /* DS2490 is currently halted */ +#define ST_IDLE 0x20 /* DS2490 is currently idle */ +#define ST_EPOF 0x80 +/* Status transfer size, 16 bytes status, 16 byte result flags */ +#define ST_SIZE 0x20 + +/* Result Register flags */ +#define RR_DETECT 0xA5 /* New device detected */ +#define RR_NRS 0x01 /* Reset no presence or ... */ +#define RR_SH 0x02 /* short on reset or set path */ +#define RR_APP 0x04 /* alarming presence on reset */ +#define RR_VPP 0x08 /* 12V expected not seen */ +#define RR_CMP 0x10 /* compare error */ +#define RR_CRC 0x20 /* CRC error detected */ +#define RR_RDP 0x40 /* redirected page */ +#define RR_EOS 0x80 /* end of search error */ + +#define SPEED_NORMAL 0x00 +#define SPEED_FLEXIBLE 0x01 +#define SPEED_OVERDRIVE 0x02 + +#define NUM_EP 4 +#define EP_CONTROL 0 +#define EP_STATUS 1 +#define EP_DATA_OUT 2 +#define EP_DATA_IN 3 + +struct ds_device { + struct list_head ds_entry; + + struct usb_device *udev; + struct usb_interface *intf; + + int ep[NUM_EP]; + + /* Strong PullUp + * 0: pullup not active, else duration in milliseconds + */ + int spu_sleep; + /* spu_bit contains COMM_SPU or 0 depending on if the strong pullup + * should be active or not for writes. + */ + u16 spu_bit; + + u8 st_buf[ST_SIZE]; + u8 byte_buf; + + struct w1_bus_master master; +}; + +struct ds_status { + u8 enable; + u8 speed; + u8 pullup_dur; + u8 ppuls_dur; + u8 pulldown_slew; + u8 write1_time; + u8 write0_time; + u8 reserved0; + u8 status; + u8 command0; + u8 command1; + u8 command_buffer_status; + u8 data_out_buffer_status; + u8 data_in_buffer_status; + u8 reserved1; + u8 reserved2; +}; + +static LIST_HEAD(ds_devices); +static DEFINE_MUTEX(ds_mutex); + +static int ds_send_control_cmd(struct ds_device *dev, u16 value, u16 index) +{ + int err; + + err = usb_control_msg(dev->udev, usb_sndctrlpipe(dev->udev, dev->ep[EP_CONTROL]), + CONTROL_CMD, VENDOR, value, index, NULL, 0, 1000); + if (err < 0) { + dev_err(&dev->udev->dev, + "Failed to send command control message %x.%x: err=%d.\n", + value, index, err); + return err; + } + + return err; +} + +static int ds_send_control_mode(struct ds_device *dev, u16 value, u16 index) +{ + int err; + + err = usb_control_msg(dev->udev, usb_sndctrlpipe(dev->udev, dev->ep[EP_CONTROL]), + MODE_CMD, VENDOR, value, index, NULL, 0, 1000); + if (err < 0) { + dev_err(&dev->udev->dev, + "Failed to send mode control message %x.%x: err=%d.\n", + value, index, err); + return err; + } + + return err; +} + +static int ds_send_control(struct ds_device *dev, u16 value, u16 index) +{ + int err; + + err = usb_control_msg(dev->udev, usb_sndctrlpipe(dev->udev, dev->ep[EP_CONTROL]), + COMM_CMD, VENDOR, value, index, NULL, 0, 1000); + if (err < 0) { + dev_err(&dev->udev->dev, + "Failed to send control message %x.%x: err=%d.\n", + value, index, err); + return err; + } + + return err; +} + +static void ds_dump_status(struct ds_device *ds_dev, unsigned char *buf, int count) +{ + struct device *dev = &ds_dev->udev->dev; + int i; + + dev_info(dev, "ep_status=0x%x, count=%d, status=%*phC", + ds_dev->ep[EP_STATUS], count, count, buf); + + if (count >= 16) { + dev_dbg(dev, "enable flag: 0x%02x", buf[0]); + dev_dbg(dev, "1-wire speed: 0x%02x", buf[1]); + dev_dbg(dev, "strong pullup duration: 0x%02x", buf[2]); + dev_dbg(dev, "programming pulse duration: 0x%02x", buf[3]); + dev_dbg(dev, "pulldown slew rate control: 0x%02x", buf[4]); + dev_dbg(dev, "write-1 low time: 0x%02x", buf[5]); + dev_dbg(dev, "data sample offset/write-0 recovery time: 0x%02x", buf[6]); + dev_dbg(dev, "reserved (test register): 0x%02x", buf[7]); + dev_dbg(dev, "device status flags: 0x%02x", buf[8]); + dev_dbg(dev, "communication command byte 1: 0x%02x", buf[9]); + dev_dbg(dev, "communication command byte 2: 0x%02x", buf[10]); + dev_dbg(dev, "communication command buffer status: 0x%02x", buf[11]); + dev_dbg(dev, "1-wire data output buffer status: 0x%02x", buf[12]); + dev_dbg(dev, "1-wire data input buffer status: 0x%02x", buf[13]); + dev_dbg(dev, "reserved: 0x%02x", buf[14]); + dev_dbg(dev, "reserved: 0x%02x", buf[15]); + } + + for (i = 16; i < count; ++i) { + if (buf[i] == RR_DETECT) { + dev_dbg(dev, "New device detect.\n"); + continue; + } + dev_dbg(dev, "Result Register Value: 0x%02x", buf[i]); + if (buf[i] & RR_NRS) + dev_dbg(dev, "NRS: Reset no presence or ...\n"); + if (buf[i] & RR_SH) + dev_dbg(dev, "SH: short on reset or set path\n"); + if (buf[i] & RR_APP) + dev_dbg(dev, "APP: alarming presence on reset\n"); + if (buf[i] & RR_VPP) + dev_dbg(dev, "VPP: 12V expected not seen\n"); + if (buf[i] & RR_CMP) + dev_dbg(dev, "CMP: compare error\n"); + if (buf[i] & RR_CRC) + dev_dbg(dev, "CRC: CRC error detected\n"); + if (buf[i] & RR_RDP) + dev_dbg(dev, "RDP: redirected page\n"); + if (buf[i] & RR_EOS) + dev_dbg(dev, "EOS: end of search error\n"); + } +} + +static int ds_recv_status(struct ds_device *dev, struct ds_status *st) +{ + int count, err; + + if (st) + memset(st, 0, sizeof(*st)); + + count = 0; + err = usb_interrupt_msg(dev->udev, + usb_rcvintpipe(dev->udev, + dev->ep[EP_STATUS]), + dev->st_buf, sizeof(dev->st_buf), + &count, 1000); + if (err < 0) { + dev_err(&dev->udev->dev, + "Failed to read 1-wire data from 0x%x: err=%d.\n", + dev->ep[EP_STATUS], err); + return err; + } + + if (st && count >= sizeof(*st)) + memcpy(st, dev->st_buf, sizeof(*st)); + + return count; +} + +static void ds_reset_device(struct ds_device *dev) +{ + ds_send_control_cmd(dev, CTL_RESET_DEVICE, 0); + /* Always allow strong pullup which allow individual writes to use + * the strong pullup. + */ + if (ds_send_control_mode(dev, MOD_PULSE_EN, PULSE_SPUE)) + dev_err(&dev->udev->dev, + "%s: Error allowing strong pullup\n", __func__); + /* Chip strong pullup time was cleared. */ + if (dev->spu_sleep) { + /* lower 4 bits are 0, see ds_set_pullup */ + u8 del = dev->spu_sleep>>4; + + if (ds_send_control(dev, COMM_SET_DURATION | COMM_IM, del)) + dev_err(&dev->udev->dev, + "%s: Error setting duration\n", __func__); + } +} + +static int ds_recv_data(struct ds_device *dev, unsigned char *buf, int size) +{ + int count, err; + + /* Careful on size. If size is less than what is available in + * the input buffer, the device fails the bulk transfer and + * clears the input buffer. It could read the maximum size of + * the data buffer, but then do you return the first, last, or + * some set of the middle size bytes? As long as the rest of + * the code is correct there will be size bytes waiting. A + * call to ds_wait_status will wait until the device is idle + * and any data to be received would have been available. + */ + count = 0; + err = usb_bulk_msg(dev->udev, usb_rcvbulkpipe(dev->udev, dev->ep[EP_DATA_IN]), + buf, size, &count, 1000); + if (err < 0) { + int recv_len; + + dev_info(&dev->udev->dev, "Clearing ep0x%x.\n", dev->ep[EP_DATA_IN]); + usb_clear_halt(dev->udev, usb_rcvbulkpipe(dev->udev, dev->ep[EP_DATA_IN])); + + /* status might tell us why endpoint is stuck? */ + recv_len = ds_recv_status(dev, NULL); + if (recv_len >= 0) + ds_dump_status(dev, dev->st_buf, recv_len); + + return err; + } + +#if 0 + { + int i; + + printk("%s: count=%d: ", __func__, count); + for (i = 0; i < count; ++i) + printk("%02x ", buf[i]); + printk("\n"); + } +#endif + return count; +} + +static int ds_send_data(struct ds_device *dev, unsigned char *buf, int len) +{ + int count, err; + + count = 0; + err = usb_bulk_msg(dev->udev, usb_sndbulkpipe(dev->udev, dev->ep[EP_DATA_OUT]), buf, len, &count, 1000); + if (err < 0) { + dev_err(&dev->udev->dev, "Failed to write 1-wire data to ep0x%x: " + "err=%d.\n", dev->ep[EP_DATA_OUT], err); + return err; + } + + return err; +} + +#if 0 + +int ds_stop_pulse(struct ds_device *dev, int limit) +{ + struct ds_status st; + int count = 0, err = 0; + + do { + err = ds_send_control(dev, CTL_HALT_EXE_IDLE, 0); + if (err) + break; + err = ds_send_control(dev, CTL_RESUME_EXE, 0); + if (err) + break; + err = ds_recv_status(dev, &st); + if (err) + break; + + if ((st.status & ST_SPUA) == 0) { + err = ds_send_control_mode(dev, MOD_PULSE_EN, 0); + if (err) + break; + } + } while (++count < limit); + + return err; +} + +int ds_detect(struct ds_device *dev, struct ds_status *st) +{ + int err; + + err = ds_send_control_cmd(dev, CTL_RESET_DEVICE, 0); + if (err) + return err; + + err = ds_send_control(dev, COMM_SET_DURATION | COMM_IM, 0); + if (err) + return err; + + err = ds_send_control(dev, COMM_SET_DURATION | COMM_IM | COMM_TYPE, 0x40); + if (err) + return err; + + err = ds_send_control_mode(dev, MOD_PULSE_EN, PULSE_PROG); + if (err) + return err; + + err = ds_dump_status(dev, st); + + return err; +} + +#endif /* 0 */ + +static int ds_wait_status(struct ds_device *dev, struct ds_status *st) +{ + int err, count = 0; + + do { + st->status = 0; + err = ds_recv_status(dev, st); +#if 0 + if (err >= 0) { + int i; + printk("0x%x: count=%d, status: ", dev->ep[EP_STATUS], err); + for (i = 0; i < err; ++i) + printk("%02x ", dev->st_buf[i]); + printk("\n"); + } +#endif + } while (!(st->status & ST_IDLE) && !(err < 0) && ++count < 100); + + if (err >= 16 && st->status & ST_EPOF) { + dev_info(&dev->udev->dev, "Resetting device after ST_EPOF.\n"); + ds_reset_device(dev); + /* Always dump the device status. */ + count = 101; + } + + /* Dump the status for errors or if there is extended return data. + * The extended status includes new device detection (maybe someone + * can do something with it). + */ + if (err > 16 || count >= 100 || err < 0) + ds_dump_status(dev, dev->st_buf, err); + + /* Extended data isn't an error. Well, a short is, but the dump + * would have already told the user that and we can't do anything + * about it in software anyway. + */ + if (count >= 100 || err < 0) + return -1; + else + return 0; +} + +static int ds_reset(struct ds_device *dev) +{ + int err; + + /* Other potentionally interesting flags for reset. + * + * COMM_NTF: Return result register feedback. This could be used to + * detect some conditions such as short, alarming presence, or + * detect if a new device was detected. + * + * COMM_SE which allows SPEED_NORMAL, SPEED_FLEXIBLE, SPEED_OVERDRIVE: + * Select the data transfer rate. + */ + err = ds_send_control(dev, COMM_1_WIRE_RESET | COMM_IM, SPEED_NORMAL); + if (err) + return err; + + return 0; +} + +#if 0 +static int ds_set_speed(struct ds_device *dev, int speed) +{ + int err; + + if (speed != SPEED_NORMAL && speed != SPEED_FLEXIBLE && speed != SPEED_OVERDRIVE) + return -EINVAL; + + if (speed != SPEED_OVERDRIVE) + speed = SPEED_FLEXIBLE; + + speed &= 0xff; + + err = ds_send_control_mode(dev, MOD_1WIRE_SPEED, speed); + if (err) + return err; + + return err; +} +#endif /* 0 */ + +static int ds_set_pullup(struct ds_device *dev, int delay) +{ + int err = 0; + u8 del = 1 + (u8)(delay >> 4); + /* Just storing delay would not get the trunication and roundup. */ + int ms = del<<4; + + /* Enable spu_bit if a delay is set. */ + dev->spu_bit = delay ? COMM_SPU : 0; + /* If delay is zero, it has already been disabled, if the time is + * the same as the hardware was last programmed to, there is also + * nothing more to do. Compare with the recalculated value ms + * rather than del or delay which can have a different value. + */ + if (delay == 0 || ms == dev->spu_sleep) + return err; + + err = ds_send_control(dev, COMM_SET_DURATION | COMM_IM, del); + if (err) + return err; + + dev->spu_sleep = ms; + + return err; +} + +static int ds_touch_bit(struct ds_device *dev, u8 bit, u8 *tbit) +{ + int err; + struct ds_status st; + + err = ds_send_control(dev, COMM_BIT_IO | COMM_IM | (bit ? COMM_D : 0), + 0); + if (err) + return err; + + ds_wait_status(dev, &st); + + err = ds_recv_data(dev, tbit, sizeof(*tbit)); + if (err < 0) + return err; + + return 0; +} + +#if 0 +static int ds_write_bit(struct ds_device *dev, u8 bit) +{ + int err; + struct ds_status st; + + /* Set COMM_ICP to write without a readback. Note, this will + * produce one time slot, a down followed by an up with COMM_D + * only determing the timing. + */ + err = ds_send_control(dev, COMM_BIT_IO | COMM_IM | COMM_ICP | + (bit ? COMM_D : 0), 0); + if (err) + return err; + + ds_wait_status(dev, &st); + + return 0; +} +#endif + +static int ds_write_byte(struct ds_device *dev, u8 byte) +{ + int err; + struct ds_status st; + + err = ds_send_control(dev, COMM_BYTE_IO | COMM_IM | dev->spu_bit, byte); + if (err) + return err; + + if (dev->spu_bit) + msleep(dev->spu_sleep); + + err = ds_wait_status(dev, &st); + if (err) + return err; + + err = ds_recv_data(dev, &dev->byte_buf, 1); + if (err < 0) + return err; + + return !(byte == dev->byte_buf); +} + +static int ds_read_byte(struct ds_device *dev, u8 *byte) +{ + int err; + struct ds_status st; + + err = ds_send_control(dev, COMM_BYTE_IO | COMM_IM, 0xff); + if (err) + return err; + + ds_wait_status(dev, &st); + + err = ds_recv_data(dev, byte, sizeof(*byte)); + if (err < 0) + return err; + + return 0; +} + +static int ds_read_block(struct ds_device *dev, u8 *buf, int len) +{ + struct ds_status st; + int err; + + if (len > 64*1024) + return -E2BIG; + + memset(buf, 0xFF, len); + + err = ds_send_data(dev, buf, len); + if (err < 0) + return err; + + err = ds_send_control(dev, COMM_BLOCK_IO | COMM_IM, len); + if (err) + return err; + + ds_wait_status(dev, &st); + + memset(buf, 0x00, len); + err = ds_recv_data(dev, buf, len); + + return err; +} + +static int ds_write_block(struct ds_device *dev, u8 *buf, int len) +{ + int err; + struct ds_status st; + + err = ds_send_data(dev, buf, len); + if (err < 0) + return err; + + err = ds_send_control(dev, COMM_BLOCK_IO | COMM_IM | dev->spu_bit, len); + if (err) + return err; + + if (dev->spu_bit) + msleep(dev->spu_sleep); + + ds_wait_status(dev, &st); + + err = ds_recv_data(dev, buf, len); + if (err < 0) + return err; + + return !(err == len); +} + +static void ds9490r_search(void *data, struct w1_master *master, + u8 search_type, w1_slave_found_callback callback) +{ + /* When starting with an existing id, the first id returned will + * be that device (if it is still on the bus most likely). + * + * If the number of devices found is less than or equal to the + * search_limit, that number of IDs will be returned. If there are + * more, search_limit IDs will be returned followed by a non-zero + * discrepency value. + */ + struct ds_device *dev = data; + int err; + u16 value, index; + struct ds_status st; + int search_limit; + int found = 0; + int i; + + /* DS18b20 spec, 13.16 ms per device, 75 per second, sleep for + * discovering 8 devices (1 bulk transfer and 1/2 FIFO size) at a time. + */ + const unsigned long jtime = msecs_to_jiffies(1000*8/75); + /* FIFO 128 bytes, bulk packet size 64, read a multiple of the + * packet size. + */ + const size_t bufsize = 2 * 64; + u64 *buf, *found_ids; + + buf = kmalloc(bufsize, GFP_KERNEL); + if (!buf) + return; + + /* + * We are holding the bus mutex during the scan, but adding devices via the + * callback needs the bus to be unlocked. So we queue up found ids here. + */ + found_ids = kmalloc_array(master->max_slave_count, sizeof(u64), GFP_KERNEL); + if (!found_ids) { + kfree(buf); + return; + } + + mutex_lock(&master->bus_mutex); + + /* address to start searching at */ + if (ds_send_data(dev, (u8 *)&master->search_id, 8) < 0) + goto search_out; + master->search_id = 0; + + value = COMM_SEARCH_ACCESS | COMM_IM | COMM_RST | COMM_SM | COMM_F | + COMM_RTS; + search_limit = master->max_slave_count; + if (search_limit > 255) + search_limit = 0; + index = search_type | (search_limit << 8); + if (ds_send_control(dev, value, index) < 0) + goto search_out; + + do { + schedule_timeout(jtime); + + err = ds_recv_status(dev, &st); + if (err < 0 || err < sizeof(st)) + break; + + if (st.data_in_buffer_status) { + /* + * Bulk in can receive partial ids, but when it does + * they fail crc and will be discarded anyway. + * That has only been seen when status in buffer + * is 0 and bulk is read anyway, so don't read + * bulk without first checking if status says there + * is data to read. + */ + err = ds_recv_data(dev, (u8 *)buf, bufsize); + if (err < 0) + break; + for (i = 0; i < err/8; ++i) { + found_ids[found++] = buf[i]; + /* + * can't know if there will be a discrepancy + * value after until the next id + */ + if (found == search_limit) { + master->search_id = buf[i]; + break; + } + } + } + + if (test_bit(W1_ABORT_SEARCH, &master->flags)) + break; + } while (!(st.status & (ST_IDLE | ST_HALT))); + + /* only continue the search if some weren't found */ + if (found <= search_limit) { + master->search_id = 0; + } else if (!test_bit(W1_WARN_MAX_COUNT, &master->flags)) { + /* + * Only max_slave_count will be scanned in a search, + * but it will start where it left off next search + * until all ids are identified and then it will start + * over. A continued search will report the previous + * last id as the first id (provided it is still on the + * bus). + */ + dev_info(&dev->udev->dev, "%s: max_slave_count %d reached, " + "will continue next search.\n", __func__, + master->max_slave_count); + set_bit(W1_WARN_MAX_COUNT, &master->flags); + } + +search_out: + mutex_unlock(&master->bus_mutex); + kfree(buf); + + for (i = 0; i < found; i++) /* run callback for all queued up IDs */ + callback(master, found_ids[i]); + kfree(found_ids); +} + +#if 0 +/* + * FIXME: if this disabled code is ever used in the future all ds_send_data() + * calls must be changed to use a DMAable buffer. + */ +static int ds_match_access(struct ds_device *dev, u64 init) +{ + int err; + struct ds_status st; + + err = ds_send_data(dev, (unsigned char *)&init, sizeof(init)); + if (err) + return err; + + ds_wait_status(dev, &st); + + err = ds_send_control(dev, COMM_MATCH_ACCESS | COMM_IM | COMM_RST, 0x0055); + if (err) + return err; + + ds_wait_status(dev, &st); + + return 0; +} + +static int ds_set_path(struct ds_device *dev, u64 init) +{ + int err; + struct ds_status st; + u8 buf[9]; + + memcpy(buf, &init, 8); + buf[8] = BRANCH_MAIN; + + err = ds_send_data(dev, buf, sizeof(buf)); + if (err) + return err; + + ds_wait_status(dev, &st); + + err = ds_send_control(dev, COMM_SET_PATH | COMM_IM | COMM_RST, 0); + if (err) + return err; + + ds_wait_status(dev, &st); + + return 0; +} + +#endif /* 0 */ + +static u8 ds9490r_touch_bit(void *data, u8 bit) +{ + struct ds_device *dev = data; + + if (ds_touch_bit(dev, bit, &dev->byte_buf)) + return 0; + + return dev->byte_buf; +} + +#if 0 +static void ds9490r_write_bit(void *data, u8 bit) +{ + struct ds_device *dev = data; + + ds_write_bit(dev, bit); +} + +static u8 ds9490r_read_bit(void *data) +{ + struct ds_device *dev = data; + int err; + + err = ds_touch_bit(dev, 1, &dev->byte_buf); + if (err) + return 0; + + return dev->byte_buf & 1; +} +#endif + +static void ds9490r_write_byte(void *data, u8 byte) +{ + struct ds_device *dev = data; + + ds_write_byte(dev, byte); +} + +static u8 ds9490r_read_byte(void *data) +{ + struct ds_device *dev = data; + int err; + + err = ds_read_byte(dev, &dev->byte_buf); + if (err) + return 0; + + return dev->byte_buf; +} + +static void ds9490r_write_block(void *data, const u8 *buf, int len) +{ + struct ds_device *dev = data; + u8 *tbuf; + + if (len <= 0) + return; + + tbuf = kmemdup(buf, len, GFP_KERNEL); + if (!tbuf) + return; + + ds_write_block(dev, tbuf, len); + + kfree(tbuf); +} + +static u8 ds9490r_read_block(void *data, u8 *buf, int len) +{ + struct ds_device *dev = data; + int err; + u8 *tbuf; + + if (len <= 0) + return 0; + + tbuf = kmalloc(len, GFP_KERNEL); + if (!tbuf) + return 0; + + err = ds_read_block(dev, tbuf, len); + if (err >= 0) + memcpy(buf, tbuf, len); + + kfree(tbuf); + + return err >= 0 ? len : 0; +} + +static u8 ds9490r_reset(void *data) +{ + struct ds_device *dev = data; + int err; + + err = ds_reset(dev); + if (err) + return 1; + + return 0; +} + +static u8 ds9490r_set_pullup(void *data, int delay) +{ + struct ds_device *dev = data; + + if (ds_set_pullup(dev, delay)) + return 1; + + return 0; +} + +static int ds_w1_init(struct ds_device *dev) +{ + memset(&dev->master, 0, sizeof(struct w1_bus_master)); + + /* Reset the device as it can be in a bad state. + * This is necessary because a block write will wait for data + * to be placed in the output buffer and block any later + * commands which will keep accumulating and the device will + * not be idle. Another case is removing the ds2490 module + * while a bus search is in progress, somehow a few commands + * get through, but the input transfers fail leaving data in + * the input buffer. This will cause the next read to fail + * see the note in ds_recv_data. + */ + ds_reset_device(dev); + + dev->master.data = dev; + dev->master.touch_bit = &ds9490r_touch_bit; + /* read_bit and write_bit in w1_bus_master are expected to set and + * sample the line level. For write_bit that means it is expected to + * set it to that value and leave it there. ds2490 only supports an + * individual time slot at the lowest level. The requirement from + * pulling the bus state down to reading the state is 15us, something + * that isn't realistic on the USB bus anyway. + dev->master.read_bit = &ds9490r_read_bit; + dev->master.write_bit = &ds9490r_write_bit; + */ + dev->master.read_byte = &ds9490r_read_byte; + dev->master.write_byte = &ds9490r_write_byte; + dev->master.read_block = &ds9490r_read_block; + dev->master.write_block = &ds9490r_write_block; + dev->master.reset_bus = &ds9490r_reset; + dev->master.set_pullup = &ds9490r_set_pullup; + dev->master.search = &ds9490r_search; + + return w1_add_master_device(&dev->master); +} + +static void ds_w1_fini(struct ds_device *dev) +{ + w1_remove_master_device(&dev->master); +} + +static int ds_probe(struct usb_interface *intf, + const struct usb_device_id *udev_id) +{ + struct usb_device *udev = interface_to_usbdev(intf); + struct usb_endpoint_descriptor *endpoint; + struct usb_host_interface *iface_desc; + struct ds_device *dev; + int i, err, alt; + + dev = kzalloc(sizeof(struct ds_device), GFP_KERNEL); + if (!dev) + return -ENOMEM; + + dev->udev = usb_get_dev(udev); + if (!dev->udev) { + err = -ENOMEM; + goto err_out_free; + } + memset(dev->ep, 0, sizeof(dev->ep)); + + usb_set_intfdata(intf, dev); + + err = usb_reset_configuration(dev->udev); + if (err) { + dev_err(&dev->udev->dev, + "Failed to reset configuration: err=%d.\n", err); + goto err_out_clear; + } + + /* alternative 3, 1ms interrupt (greatly speeds search), 64 byte bulk */ + alt = 3; + err = usb_set_interface(dev->udev, + intf->cur_altsetting->desc.bInterfaceNumber, alt); + if (err) { + dev_err(&dev->udev->dev, "Failed to set alternative setting %d " + "for %d interface: err=%d.\n", alt, + intf->cur_altsetting->desc.bInterfaceNumber, err); + goto err_out_clear; + } + + iface_desc = intf->cur_altsetting; + if (iface_desc->desc.bNumEndpoints != NUM_EP-1) { + dev_err(&dev->udev->dev, "Num endpoints=%d. It is not DS9490R.\n", + iface_desc->desc.bNumEndpoints); + err = -EINVAL; + goto err_out_clear; + } + + /* + * This loop doesn'd show control 0 endpoint, + * so we will fill only 1-3 endpoints entry. + */ + for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i) { + endpoint = &iface_desc->endpoint[i].desc; + + dev->ep[i+1] = endpoint->bEndpointAddress; +#if 0 + printk("%d: addr=%x, size=%d, dir=%s, type=%x\n", + i, endpoint->bEndpointAddress, le16_to_cpu(endpoint->wMaxPacketSize), + (endpoint->bEndpointAddress & USB_DIR_IN)?"IN":"OUT", + endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK); +#endif + } + + err = ds_w1_init(dev); + if (err) + goto err_out_clear; + + mutex_lock(&ds_mutex); + list_add_tail(&dev->ds_entry, &ds_devices); + mutex_unlock(&ds_mutex); + + return 0; + +err_out_clear: + usb_set_intfdata(intf, NULL); + usb_put_dev(dev->udev); +err_out_free: + kfree(dev); + return err; +} + +static void ds_disconnect(struct usb_interface *intf) +{ + struct ds_device *dev; + + dev = usb_get_intfdata(intf); + if (!dev) + return; + + mutex_lock(&ds_mutex); + list_del(&dev->ds_entry); + mutex_unlock(&ds_mutex); + + ds_w1_fini(dev); + + usb_set_intfdata(intf, NULL); + + usb_put_dev(dev->udev); + kfree(dev); +} + +static const struct usb_device_id ds_id_table[] = { + { USB_DEVICE(0x04fa, 0x2490) }, + { }, +}; +MODULE_DEVICE_TABLE(usb, ds_id_table); + +static struct usb_driver ds_driver = { + .name = "DS9490R", + .probe = ds_probe, + .disconnect = ds_disconnect, + .id_table = ds_id_table, +}; +module_usb_driver(ds_driver); + +MODULE_AUTHOR("Evgeniy Polyakov "); +MODULE_DESCRIPTION("DS2490 USB <-> W1 bus master driver (DS9490*)"); +MODULE_LICENSE("GPL"); diff --git a/drivers/w1/masters/matrox_w1.c b/drivers/w1/masters/matrox_w1.c new file mode 100644 index 0000000000..2852cd2dc6 --- /dev/null +++ b/drivers/w1/masters/matrox_w1.c @@ -0,0 +1,202 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * matrox_w1.c + * + * Copyright (c) 2004 Evgeniy Polyakov + */ + +#include +#include +#include + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +/* + * Matrox G400 DDC registers. + */ + +#define MATROX_G400_DDC_CLK (1<<4) +#define MATROX_G400_DDC_DATA (1<<1) + +#define MATROX_BASE 0x3C00 +#define MATROX_STATUS 0x1e14 + +#define MATROX_PORT_INDEX_OFFSET 0x00 +#define MATROX_PORT_DATA_OFFSET 0x0A + +#define MATROX_GET_CONTROL 0x2A +#define MATROX_GET_DATA 0x2B +#define MATROX_CURSOR_CTL 0x06 + +struct matrox_device { + void __iomem *base_addr; + void __iomem *port_index; + void __iomem *port_data; + u8 data_mask; + + unsigned long phys_addr; + void __iomem *virt_addr; + unsigned long found; + + struct w1_bus_master *bus_master; +}; + +/* + * These functions read and write DDC Data bit. + * + * Using tristate pins, since i can't find any open-drain pin in whole motherboard. + * Unfortunately we can't connect to Intel's 82801xx IO controller + * since we don't know motherboard schema, which has pretty unused(may be not) GPIO. + * + * I've heard that PIIX also has open drain pin. + * + * Port mapping. + */ +static inline u8 matrox_w1_read_reg(struct matrox_device *dev, u8 reg) +{ + u8 ret; + + writeb(reg, dev->port_index); + ret = readb(dev->port_data); + barrier(); + + return ret; +} + +static inline void matrox_w1_write_reg(struct matrox_device *dev, u8 reg, u8 val) +{ + writeb(reg, dev->port_index); + writeb(val, dev->port_data); + wmb(); +} + +static void matrox_w1_write_ddc_bit(void *data, u8 bit) +{ + u8 ret; + struct matrox_device *dev = data; + + if (bit) + bit = 0; + else + bit = dev->data_mask; + + ret = matrox_w1_read_reg(dev, MATROX_GET_CONTROL); + matrox_w1_write_reg(dev, MATROX_GET_CONTROL, ((ret & ~dev->data_mask) | bit)); + matrox_w1_write_reg(dev, MATROX_GET_DATA, 0x00); +} + +static u8 matrox_w1_read_ddc_bit(void *data) +{ + u8 ret; + struct matrox_device *dev = data; + + ret = matrox_w1_read_reg(dev, MATROX_GET_DATA); + + return ret; +} + +static void matrox_w1_hw_init(struct matrox_device *dev) +{ + matrox_w1_write_reg(dev, MATROX_GET_DATA, 0xFF); + matrox_w1_write_reg(dev, MATROX_GET_CONTROL, 0x00); +} + +static int matrox_w1_probe(struct pci_dev *pdev, const struct pci_device_id *ent) +{ + struct matrox_device *dev; + int err; + + if (pdev->vendor != PCI_VENDOR_ID_MATROX || pdev->device != PCI_DEVICE_ID_MATROX_G400) + return -ENODEV; + + dev = kzalloc(sizeof(struct matrox_device) + + sizeof(struct w1_bus_master), GFP_KERNEL); + if (!dev) + return -ENOMEM; + + dev->bus_master = (struct w1_bus_master *)(dev + 1); + + /* + * True for G400, for some other we need resource 0, see drivers/video/matrox/matroxfb_base.c + */ + + dev->phys_addr = pci_resource_start(pdev, 1); + + dev->virt_addr = ioremap(dev->phys_addr, 16384); + if (!dev->virt_addr) { + dev_err(&pdev->dev, "%s: failed to ioremap(0x%lx, %d).\n", + __func__, dev->phys_addr, 16384); + err = -EIO; + goto err_out_free_device; + } + + dev->base_addr = dev->virt_addr + MATROX_BASE; + dev->port_index = dev->base_addr + MATROX_PORT_INDEX_OFFSET; + dev->port_data = dev->base_addr + MATROX_PORT_DATA_OFFSET; + dev->data_mask = (MATROX_G400_DDC_DATA); + + matrox_w1_hw_init(dev); + + dev->bus_master->data = dev; + dev->bus_master->read_bit = &matrox_w1_read_ddc_bit; + dev->bus_master->write_bit = &matrox_w1_write_ddc_bit; + + err = w1_add_master_device(dev->bus_master); + if (err) + goto err_out_free_device; + + pci_set_drvdata(pdev, dev); + + dev->found = 1; + + dev_info(&pdev->dev, "Matrox G400 GPIO transport layer for 1-wire.\n"); + + return 0; + +err_out_free_device: + if (dev->virt_addr) + iounmap(dev->virt_addr); + kfree(dev); + + return err; +} + +static void matrox_w1_remove(struct pci_dev *pdev) +{ + struct matrox_device *dev = pci_get_drvdata(pdev); + + if (dev->found) { + w1_remove_master_device(dev->bus_master); + iounmap(dev->virt_addr); + } + kfree(dev); +} + +static struct pci_device_id matrox_w1_tbl[] = { + { PCI_DEVICE(PCI_VENDOR_ID_MATROX, PCI_DEVICE_ID_MATROX_G400) }, + { }, +}; +MODULE_DEVICE_TABLE(pci, matrox_w1_tbl); + +static struct pci_driver matrox_w1_pci_driver = { + .name = "matrox_w1", + .id_table = matrox_w1_tbl, + .probe = matrox_w1_probe, + .remove = matrox_w1_remove, +}; +module_pci_driver(matrox_w1_pci_driver); + +MODULE_AUTHOR("Evgeniy Polyakov "); +MODULE_DESCRIPTION("Driver for transport(Dallas 1-wire protocol) over VGA DDC(matrox gpio)."); +MODULE_LICENSE("GPL"); diff --git a/drivers/w1/masters/mxc_w1.c b/drivers/w1/masters/mxc_w1.c new file mode 100644 index 0000000000..090cbbf9e1 --- /dev/null +++ b/drivers/w1/masters/mxc_w1.c @@ -0,0 +1,183 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Copyright 2005-2008 Freescale Semiconductor, Inc. All Rights Reserved. + * Copyright 2008 Luotao Fu, kernel@pengutronix.de + */ + +#include +#include +#include +#include +#include +#include +#include + +#include + +/* + * MXC W1 Register offsets + */ +#define MXC_W1_CONTROL 0x00 +# define MXC_W1_CONTROL_RDST BIT(3) +# define MXC_W1_CONTROL_WR(x) BIT(5 - (x)) +# define MXC_W1_CONTROL_PST BIT(6) +# define MXC_W1_CONTROL_RPP BIT(7) +#define MXC_W1_TIME_DIVIDER 0x02 +#define MXC_W1_RESET 0x04 +# define MXC_W1_RESET_RST BIT(0) + +struct mxc_w1_device { + void __iomem *regs; + struct clk *clk; + struct w1_bus_master bus_master; +}; + +/* + * this is the low level routine to + * reset the device on the One Wire interface + * on the hardware + */ +static u8 mxc_w1_ds2_reset_bus(void *data) +{ + struct mxc_w1_device *dev = data; + ktime_t timeout; + + writeb(MXC_W1_CONTROL_RPP, dev->regs + MXC_W1_CONTROL); + + /* Wait for reset sequence 511+512us, use 1500us for sure */ + timeout = ktime_add_us(ktime_get(), 1500); + + udelay(511 + 512); + + do { + u8 ctrl = readb(dev->regs + MXC_W1_CONTROL); + + /* PST bit is valid after the RPP bit is self-cleared */ + if (!(ctrl & MXC_W1_CONTROL_RPP)) + return !(ctrl & MXC_W1_CONTROL_PST); + } while (ktime_before(ktime_get(), timeout)); + + return 1; +} + +/* + * this is the low level routine to read/write a bit on the One Wire + * interface on the hardware. It does write 0 if parameter bit is set + * to 0, otherwise a write 1/read. + */ +static u8 mxc_w1_ds2_touch_bit(void *data, u8 bit) +{ + struct mxc_w1_device *dev = data; + ktime_t timeout; + + writeb(MXC_W1_CONTROL_WR(bit), dev->regs + MXC_W1_CONTROL); + + /* Wait for read/write bit (60us, Max 120us), use 200us for sure */ + timeout = ktime_add_us(ktime_get(), 200); + + udelay(60); + + do { + u8 ctrl = readb(dev->regs + MXC_W1_CONTROL); + + /* RDST bit is valid after the WR1/RD bit is self-cleared */ + if (!(ctrl & MXC_W1_CONTROL_WR(bit))) + return !!(ctrl & MXC_W1_CONTROL_RDST); + } while (ktime_before(ktime_get(), timeout)); + + return 0; +} + +static int mxc_w1_probe(struct platform_device *pdev) +{ + struct mxc_w1_device *mdev; + unsigned long clkrate; + unsigned int clkdiv; + int err; + + mdev = devm_kzalloc(&pdev->dev, sizeof(struct mxc_w1_device), + GFP_KERNEL); + if (!mdev) + return -ENOMEM; + + mdev->clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(mdev->clk)) + return PTR_ERR(mdev->clk); + + err = clk_prepare_enable(mdev->clk); + if (err) + return err; + + clkrate = clk_get_rate(mdev->clk); + if (clkrate < 10000000) + dev_warn(&pdev->dev, + "Low clock frequency causes improper function\n"); + + clkdiv = DIV_ROUND_CLOSEST(clkrate, 1000000); + clkrate /= clkdiv; + if ((clkrate < 980000) || (clkrate > 1020000)) + dev_warn(&pdev->dev, + "Incorrect time base frequency %lu Hz\n", clkrate); + + mdev->regs = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(mdev->regs)) { + err = PTR_ERR(mdev->regs); + goto out_disable_clk; + } + + /* Software reset 1-Wire module */ + writeb(MXC_W1_RESET_RST, mdev->regs + MXC_W1_RESET); + writeb(0, mdev->regs + MXC_W1_RESET); + + writeb(clkdiv - 1, mdev->regs + MXC_W1_TIME_DIVIDER); + + mdev->bus_master.data = mdev; + mdev->bus_master.reset_bus = mxc_w1_ds2_reset_bus; + mdev->bus_master.touch_bit = mxc_w1_ds2_touch_bit; + + platform_set_drvdata(pdev, mdev); + + err = w1_add_master_device(&mdev->bus_master); + if (err) + goto out_disable_clk; + + return 0; + +out_disable_clk: + clk_disable_unprepare(mdev->clk); + return err; +} + +/* + * disassociate the w1 device from the driver + */ +static int mxc_w1_remove(struct platform_device *pdev) +{ + struct mxc_w1_device *mdev = platform_get_drvdata(pdev); + + w1_remove_master_device(&mdev->bus_master); + + clk_disable_unprepare(mdev->clk); + + return 0; +} + +static const struct of_device_id mxc_w1_dt_ids[] = { + { .compatible = "fsl,imx21-owire" }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, mxc_w1_dt_ids); + +static struct platform_driver mxc_w1_driver = { + .driver = { + .name = "mxc_w1", + .of_match_table = mxc_w1_dt_ids, + }, + .probe = mxc_w1_probe, + .remove = mxc_w1_remove, +}; +module_platform_driver(mxc_w1_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Freescale Semiconductors Inc"); +MODULE_DESCRIPTION("Driver for One-Wire on MXC"); diff --git a/drivers/w1/masters/omap_hdq.c b/drivers/w1/masters/omap_hdq.c new file mode 100644 index 0000000000..6a39b71eb7 --- /dev/null +++ b/drivers/w1/masters/omap_hdq.c @@ -0,0 +1,688 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2007,2012 Texas Instruments, Inc. + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +#define MOD_NAME "OMAP_HDQ:" + +#define OMAP_HDQ_REVISION 0x00 +#define OMAP_HDQ_TX_DATA 0x04 +#define OMAP_HDQ_RX_DATA 0x08 +#define OMAP_HDQ_CTRL_STATUS 0x0c +#define OMAP_HDQ_CTRL_STATUS_SINGLE BIT(7) +#define OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK BIT(6) +#define OMAP_HDQ_CTRL_STATUS_CLOCKENABLE BIT(5) +#define OMAP_HDQ_CTRL_STATUS_GO BIT(4) +#define OMAP_HDQ_CTRL_STATUS_PRESENCE BIT(3) +#define OMAP_HDQ_CTRL_STATUS_INITIALIZATION BIT(2) +#define OMAP_HDQ_CTRL_STATUS_DIR BIT(1) +#define OMAP_HDQ_INT_STATUS 0x10 +#define OMAP_HDQ_INT_STATUS_TXCOMPLETE BIT(2) +#define OMAP_HDQ_INT_STATUS_RXCOMPLETE BIT(1) +#define OMAP_HDQ_INT_STATUS_TIMEOUT BIT(0) + +#define OMAP_HDQ_FLAG_CLEAR 0 +#define OMAP_HDQ_FLAG_SET 1 +#define OMAP_HDQ_TIMEOUT (HZ/5) + +#define OMAP_HDQ_MAX_USER 4 + +static DECLARE_WAIT_QUEUE_HEAD(hdq_wait_queue); + +static int w1_id; +module_param(w1_id, int, 0400); +MODULE_PARM_DESC(w1_id, "1-wire id for the slave detection in HDQ mode"); + +struct hdq_data { + struct device *dev; + void __iomem *hdq_base; + /* lock read/write/break operations */ + struct mutex hdq_mutex; + /* interrupt status and a lock for it */ + u8 hdq_irqstatus; + spinlock_t hdq_spinlock; + /* mode: 0-HDQ 1-W1 */ + int mode; + +}; + +/* HDQ register I/O routines */ +static inline u8 hdq_reg_in(struct hdq_data *hdq_data, u32 offset) +{ + return __raw_readl(hdq_data->hdq_base + offset); +} + +static inline void hdq_reg_out(struct hdq_data *hdq_data, u32 offset, u8 val) +{ + __raw_writel(val, hdq_data->hdq_base + offset); +} + +static inline u8 hdq_reg_merge(struct hdq_data *hdq_data, u32 offset, + u8 val, u8 mask) +{ + u8 new_val = (__raw_readl(hdq_data->hdq_base + offset) & ~mask) + | (val & mask); + __raw_writel(new_val, hdq_data->hdq_base + offset); + + return new_val; +} + +/* + * Wait for one or more bits in flag change. + * HDQ_FLAG_SET: wait until any bit in the flag is set. + * HDQ_FLAG_CLEAR: wait until all bits in the flag are cleared. + * return 0 on success and -ETIMEDOUT in the case of timeout. + */ +static int hdq_wait_for_flag(struct hdq_data *hdq_data, u32 offset, + u8 flag, u8 flag_set, u8 *status) +{ + int ret = 0; + unsigned long timeout = jiffies + OMAP_HDQ_TIMEOUT; + + if (flag_set == OMAP_HDQ_FLAG_CLEAR) { + /* wait for the flag clear */ + while (((*status = hdq_reg_in(hdq_data, offset)) & flag) + && time_before(jiffies, timeout)) { + schedule_timeout_uninterruptible(1); + } + if (*status & flag) + ret = -ETIMEDOUT; + } else if (flag_set == OMAP_HDQ_FLAG_SET) { + /* wait for the flag set */ + while (!((*status = hdq_reg_in(hdq_data, offset)) & flag) + && time_before(jiffies, timeout)) { + schedule_timeout_uninterruptible(1); + } + if (!(*status & flag)) + ret = -ETIMEDOUT; + } else + return -EINVAL; + + return ret; +} + +/* Clear saved irqstatus after using an interrupt */ +static u8 hdq_reset_irqstatus(struct hdq_data *hdq_data, u8 bits) +{ + unsigned long irqflags; + u8 status; + + spin_lock_irqsave(&hdq_data->hdq_spinlock, irqflags); + status = hdq_data->hdq_irqstatus; + /* this is a read-modify-write */ + hdq_data->hdq_irqstatus &= ~bits; + spin_unlock_irqrestore(&hdq_data->hdq_spinlock, irqflags); + + return status; +} + +/* write out a byte and fill *status with HDQ_INT_STATUS */ +static int hdq_write_byte(struct hdq_data *hdq_data, u8 val, u8 *status) +{ + int ret; + u8 tmp_status; + + ret = mutex_lock_interruptible(&hdq_data->hdq_mutex); + if (ret < 0) { + ret = -EINTR; + goto rtn; + } + + if (hdq_data->hdq_irqstatus) + dev_err(hdq_data->dev, "TX irqstatus not cleared (%02x)\n", + hdq_data->hdq_irqstatus); + + *status = 0; + + hdq_reg_out(hdq_data, OMAP_HDQ_TX_DATA, val); + + /* set the GO bit */ + hdq_reg_merge(hdq_data, OMAP_HDQ_CTRL_STATUS, OMAP_HDQ_CTRL_STATUS_GO, + OMAP_HDQ_CTRL_STATUS_DIR | OMAP_HDQ_CTRL_STATUS_GO); + /* wait for the TXCOMPLETE bit */ + ret = wait_event_timeout(hdq_wait_queue, + (hdq_data->hdq_irqstatus & OMAP_HDQ_INT_STATUS_TXCOMPLETE), + OMAP_HDQ_TIMEOUT); + *status = hdq_reset_irqstatus(hdq_data, OMAP_HDQ_INT_STATUS_TXCOMPLETE); + if (ret == 0) { + dev_dbg(hdq_data->dev, "TX wait elapsed\n"); + ret = -ETIMEDOUT; + goto out; + } + + /* check irqstatus */ + if (!(*status & OMAP_HDQ_INT_STATUS_TXCOMPLETE)) { + dev_dbg(hdq_data->dev, "timeout waiting for" + " TXCOMPLETE/RXCOMPLETE, %x\n", *status); + ret = -ETIMEDOUT; + goto out; + } + + /* wait for the GO bit return to zero */ + ret = hdq_wait_for_flag(hdq_data, OMAP_HDQ_CTRL_STATUS, + OMAP_HDQ_CTRL_STATUS_GO, + OMAP_HDQ_FLAG_CLEAR, &tmp_status); + if (ret) { + dev_dbg(hdq_data->dev, "timeout waiting GO bit" + " return to zero, %x\n", tmp_status); + } + +out: + mutex_unlock(&hdq_data->hdq_mutex); +rtn: + return ret; +} + +/* HDQ Interrupt service routine */ +static irqreturn_t hdq_isr(int irq, void *_hdq) +{ + struct hdq_data *hdq_data = _hdq; + unsigned long irqflags; + + spin_lock_irqsave(&hdq_data->hdq_spinlock, irqflags); + hdq_data->hdq_irqstatus |= hdq_reg_in(hdq_data, OMAP_HDQ_INT_STATUS); + spin_unlock_irqrestore(&hdq_data->hdq_spinlock, irqflags); + dev_dbg(hdq_data->dev, "hdq_isr: %x\n", hdq_data->hdq_irqstatus); + + if (hdq_data->hdq_irqstatus & + (OMAP_HDQ_INT_STATUS_TXCOMPLETE | OMAP_HDQ_INT_STATUS_RXCOMPLETE + | OMAP_HDQ_INT_STATUS_TIMEOUT)) { + /* wake up sleeping process */ + wake_up(&hdq_wait_queue); + } + + return IRQ_HANDLED; +} + +/* W1 search callback function in HDQ mode */ +static void omap_w1_search_bus(void *_hdq, struct w1_master *master_dev, + u8 search_type, w1_slave_found_callback slave_found) +{ + u64 module_id, rn_le, cs, id; + + if (w1_id) + module_id = w1_id; + else + module_id = 0x1; + + rn_le = cpu_to_le64(module_id); + /* + * HDQ might not obey truly the 1-wire spec. + * So calculate CRC based on module parameter. + */ + cs = w1_calc_crc8((u8 *)&rn_le, 7); + id = (cs << 56) | module_id; + + slave_found(master_dev, id); +} + +/* Issue break pulse to the device */ +static int omap_hdq_break(struct hdq_data *hdq_data) +{ + int ret = 0; + u8 tmp_status; + + ret = mutex_lock_interruptible(&hdq_data->hdq_mutex); + if (ret < 0) { + dev_dbg(hdq_data->dev, "Could not acquire mutex\n"); + ret = -EINTR; + goto rtn; + } + + if (hdq_data->hdq_irqstatus) + dev_err(hdq_data->dev, "break irqstatus not cleared (%02x)\n", + hdq_data->hdq_irqstatus); + + /* set the INIT and GO bit */ + hdq_reg_merge(hdq_data, OMAP_HDQ_CTRL_STATUS, + OMAP_HDQ_CTRL_STATUS_INITIALIZATION | OMAP_HDQ_CTRL_STATUS_GO, + OMAP_HDQ_CTRL_STATUS_DIR | OMAP_HDQ_CTRL_STATUS_INITIALIZATION | + OMAP_HDQ_CTRL_STATUS_GO); + + /* wait for the TIMEOUT bit */ + ret = wait_event_timeout(hdq_wait_queue, + (hdq_data->hdq_irqstatus & OMAP_HDQ_INT_STATUS_TIMEOUT), + OMAP_HDQ_TIMEOUT); + tmp_status = hdq_reset_irqstatus(hdq_data, OMAP_HDQ_INT_STATUS_TIMEOUT); + if (ret == 0) { + dev_dbg(hdq_data->dev, "break wait elapsed\n"); + ret = -EINTR; + goto out; + } + + /* check irqstatus */ + if (!(tmp_status & OMAP_HDQ_INT_STATUS_TIMEOUT)) { + dev_dbg(hdq_data->dev, "timeout waiting for TIMEOUT, %x\n", + tmp_status); + ret = -ETIMEDOUT; + goto out; + } + + /* + * check for the presence detect bit to get + * set to show that the slave is responding + */ + if (!(hdq_reg_in(hdq_data, OMAP_HDQ_CTRL_STATUS) & + OMAP_HDQ_CTRL_STATUS_PRESENCE)) { + dev_dbg(hdq_data->dev, "Presence bit not set\n"); + ret = -ETIMEDOUT; + goto out; + } + + /* + * wait for both INIT and GO bits rerurn to zero. + * zero wait time expected for interrupt mode. + */ + ret = hdq_wait_for_flag(hdq_data, OMAP_HDQ_CTRL_STATUS, + OMAP_HDQ_CTRL_STATUS_INITIALIZATION | + OMAP_HDQ_CTRL_STATUS_GO, OMAP_HDQ_FLAG_CLEAR, + &tmp_status); + if (ret) + dev_dbg(hdq_data->dev, "timeout waiting INIT&GO bits" + " return to zero, %x\n", tmp_status); + +out: + mutex_unlock(&hdq_data->hdq_mutex); +rtn: + return ret; +} + +static int hdq_read_byte(struct hdq_data *hdq_data, u8 *val) +{ + int ret = 0; + u8 status; + + ret = mutex_lock_interruptible(&hdq_data->hdq_mutex); + if (ret < 0) { + ret = -EINTR; + goto rtn; + } + + if (pm_runtime_suspended(hdq_data->dev)) { + ret = -EINVAL; + goto out; + } + + if (!(hdq_data->hdq_irqstatus & OMAP_HDQ_INT_STATUS_RXCOMPLETE)) { + hdq_reg_merge(hdq_data, OMAP_HDQ_CTRL_STATUS, + OMAP_HDQ_CTRL_STATUS_DIR | OMAP_HDQ_CTRL_STATUS_GO, + OMAP_HDQ_CTRL_STATUS_DIR | OMAP_HDQ_CTRL_STATUS_GO); + /* + * The RX comes immediately after TX. + */ + wait_event_timeout(hdq_wait_queue, + (hdq_data->hdq_irqstatus + & (OMAP_HDQ_INT_STATUS_RXCOMPLETE | + OMAP_HDQ_INT_STATUS_TIMEOUT)), + OMAP_HDQ_TIMEOUT); + status = hdq_reset_irqstatus(hdq_data, + OMAP_HDQ_INT_STATUS_RXCOMPLETE | + OMAP_HDQ_INT_STATUS_TIMEOUT); + hdq_reg_merge(hdq_data, OMAP_HDQ_CTRL_STATUS, 0, + OMAP_HDQ_CTRL_STATUS_DIR); + + /* check irqstatus */ + if (!(status & OMAP_HDQ_INT_STATUS_RXCOMPLETE)) { + dev_dbg(hdq_data->dev, "timeout waiting for" + " RXCOMPLETE, %x", status); + ret = -ETIMEDOUT; + goto out; + } + } else { /* interrupt had occurred before hdq_read_byte was called */ + hdq_reset_irqstatus(hdq_data, OMAP_HDQ_INT_STATUS_RXCOMPLETE); + } + /* the data is ready. Read it in! */ + *val = hdq_reg_in(hdq_data, OMAP_HDQ_RX_DATA); +out: + mutex_unlock(&hdq_data->hdq_mutex); +rtn: + return ret; + +} + +/* + * W1 triplet callback function - used for searching ROM addresses. + * Registered only when controller is in 1-wire mode. + */ +static u8 omap_w1_triplet(void *_hdq, u8 bdir) +{ + u8 id_bit, comp_bit; + int err; + u8 ret = 0x3; /* no slaves responded */ + struct hdq_data *hdq_data = _hdq; + u8 ctrl = OMAP_HDQ_CTRL_STATUS_SINGLE | OMAP_HDQ_CTRL_STATUS_GO | + OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK; + u8 mask = ctrl | OMAP_HDQ_CTRL_STATUS_DIR; + + err = pm_runtime_get_sync(hdq_data->dev); + if (err < 0) { + pm_runtime_put_noidle(hdq_data->dev); + + return err; + } + + err = mutex_lock_interruptible(&hdq_data->hdq_mutex); + if (err < 0) { + dev_dbg(hdq_data->dev, "Could not acquire mutex\n"); + goto rtn; + } + + /* read id_bit */ + hdq_reg_merge(_hdq, OMAP_HDQ_CTRL_STATUS, + ctrl | OMAP_HDQ_CTRL_STATUS_DIR, mask); + err = wait_event_timeout(hdq_wait_queue, + (hdq_data->hdq_irqstatus + & OMAP_HDQ_INT_STATUS_RXCOMPLETE), + OMAP_HDQ_TIMEOUT); + /* Must clear irqstatus for another RXCOMPLETE interrupt */ + hdq_reset_irqstatus(hdq_data, OMAP_HDQ_INT_STATUS_RXCOMPLETE); + + if (err == 0) { + dev_dbg(hdq_data->dev, "RX wait elapsed\n"); + goto out; + } + id_bit = (hdq_reg_in(_hdq, OMAP_HDQ_RX_DATA) & 0x01); + + /* read comp_bit */ + hdq_reg_merge(_hdq, OMAP_HDQ_CTRL_STATUS, + ctrl | OMAP_HDQ_CTRL_STATUS_DIR, mask); + err = wait_event_timeout(hdq_wait_queue, + (hdq_data->hdq_irqstatus + & OMAP_HDQ_INT_STATUS_RXCOMPLETE), + OMAP_HDQ_TIMEOUT); + /* Must clear irqstatus for another RXCOMPLETE interrupt */ + hdq_reset_irqstatus(hdq_data, OMAP_HDQ_INT_STATUS_RXCOMPLETE); + + if (err == 0) { + dev_dbg(hdq_data->dev, "RX wait elapsed\n"); + goto out; + } + comp_bit = (hdq_reg_in(_hdq, OMAP_HDQ_RX_DATA) & 0x01); + + if (id_bit && comp_bit) { + ret = 0x03; /* no slaves responded */ + goto out; + } + if (!id_bit && !comp_bit) { + /* Both bits are valid, take the direction given */ + ret = bdir ? 0x04 : 0; + } else { + /* Only one bit is valid, take that direction */ + bdir = id_bit; + ret = id_bit ? 0x05 : 0x02; + } + + /* write bdir bit */ + hdq_reg_out(_hdq, OMAP_HDQ_TX_DATA, bdir); + hdq_reg_merge(_hdq, OMAP_HDQ_CTRL_STATUS, ctrl, mask); + err = wait_event_timeout(hdq_wait_queue, + (hdq_data->hdq_irqstatus + & OMAP_HDQ_INT_STATUS_TXCOMPLETE), + OMAP_HDQ_TIMEOUT); + /* Must clear irqstatus for another TXCOMPLETE interrupt */ + hdq_reset_irqstatus(hdq_data, OMAP_HDQ_INT_STATUS_TXCOMPLETE); + + if (err == 0) { + dev_dbg(hdq_data->dev, "TX wait elapsed\n"); + goto out; + } + + hdq_reg_merge(_hdq, OMAP_HDQ_CTRL_STATUS, 0, + OMAP_HDQ_CTRL_STATUS_SINGLE); + +out: + mutex_unlock(&hdq_data->hdq_mutex); +rtn: + pm_runtime_mark_last_busy(hdq_data->dev); + pm_runtime_put_autosuspend(hdq_data->dev); + + return ret; +} + +/* reset callback */ +static u8 omap_w1_reset_bus(void *_hdq) +{ + struct hdq_data *hdq_data = _hdq; + int err; + + err = pm_runtime_get_sync(hdq_data->dev); + if (err < 0) { + pm_runtime_put_noidle(hdq_data->dev); + + return err; + } + + omap_hdq_break(hdq_data); + + pm_runtime_mark_last_busy(hdq_data->dev); + pm_runtime_put_autosuspend(hdq_data->dev); + + return 0; +} + +/* Read a byte of data from the device */ +static u8 omap_w1_read_byte(void *_hdq) +{ + struct hdq_data *hdq_data = _hdq; + u8 val = 0; + int ret; + + ret = pm_runtime_get_sync(hdq_data->dev); + if (ret < 0) { + pm_runtime_put_noidle(hdq_data->dev); + + return -1; + } + + ret = hdq_read_byte(hdq_data, &val); + if (ret) + val = -1; + + pm_runtime_mark_last_busy(hdq_data->dev); + pm_runtime_put_autosuspend(hdq_data->dev); + + return val; +} + +/* Write a byte of data to the device */ +static void omap_w1_write_byte(void *_hdq, u8 byte) +{ + struct hdq_data *hdq_data = _hdq; + int ret; + u8 status; + + ret = pm_runtime_get_sync(hdq_data->dev); + if (ret < 0) { + pm_runtime_put_noidle(hdq_data->dev); + + return; + } + + /* + * We need to reset the slave before + * issuing the SKIP ROM command, else + * the slave will not work. + */ + if (byte == W1_SKIP_ROM) + omap_hdq_break(hdq_data); + + ret = hdq_write_byte(hdq_data, byte, &status); + if (ret < 0) { + dev_dbg(hdq_data->dev, "TX failure:Ctrl status %x\n", status); + goto out_err; + } + +out_err: + pm_runtime_mark_last_busy(hdq_data->dev); + pm_runtime_put_autosuspend(hdq_data->dev); +} + +static struct w1_bus_master omap_w1_master = { + .read_byte = omap_w1_read_byte, + .write_byte = omap_w1_write_byte, + .reset_bus = omap_w1_reset_bus, +}; + +static int __maybe_unused omap_hdq_runtime_suspend(struct device *dev) +{ + struct hdq_data *hdq_data = dev_get_drvdata(dev); + + hdq_reg_out(hdq_data, 0, hdq_data->mode); + hdq_reg_in(hdq_data, OMAP_HDQ_INT_STATUS); + + return 0; +} + +static int __maybe_unused omap_hdq_runtime_resume(struct device *dev) +{ + struct hdq_data *hdq_data = dev_get_drvdata(dev); + + /* select HDQ/1W mode & enable clocks */ + hdq_reg_out(hdq_data, OMAP_HDQ_CTRL_STATUS, + OMAP_HDQ_CTRL_STATUS_CLOCKENABLE | + OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK | + hdq_data->mode); + hdq_reg_in(hdq_data, OMAP_HDQ_INT_STATUS); + + return 0; +} + +static const struct dev_pm_ops omap_hdq_pm_ops = { + SET_RUNTIME_PM_OPS(omap_hdq_runtime_suspend, + omap_hdq_runtime_resume, NULL) +}; + +static int omap_hdq_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct hdq_data *hdq_data; + int ret, irq; + u8 rev; + const char *mode; + + hdq_data = devm_kzalloc(dev, sizeof(*hdq_data), GFP_KERNEL); + if (!hdq_data) + return -ENOMEM; + + hdq_data->dev = dev; + platform_set_drvdata(pdev, hdq_data); + + hdq_data->hdq_base = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(hdq_data->hdq_base)) + return PTR_ERR(hdq_data->hdq_base); + + mutex_init(&hdq_data->hdq_mutex); + + ret = of_property_read_string(pdev->dev.of_node, "ti,mode", &mode); + if (ret < 0 || !strcmp(mode, "hdq")) { + hdq_data->mode = 0; + omap_w1_master.search = omap_w1_search_bus; + } else { + hdq_data->mode = 1; + omap_w1_master.triplet = omap_w1_triplet; + } + + pm_runtime_enable(&pdev->dev); + pm_runtime_use_autosuspend(&pdev->dev); + pm_runtime_set_autosuspend_delay(&pdev->dev, 300); + ret = pm_runtime_get_sync(&pdev->dev); + if (ret < 0) { + pm_runtime_put_noidle(&pdev->dev); + dev_dbg(&pdev->dev, "pm_runtime_get_sync failed\n"); + goto err_w1; + } + + rev = hdq_reg_in(hdq_data, OMAP_HDQ_REVISION); + dev_info(&pdev->dev, "OMAP HDQ Hardware Rev %c.%c. Driver in %s mode\n", + (rev >> 4) + '0', (rev & 0x0f) + '0', "Interrupt"); + + spin_lock_init(&hdq_data->hdq_spinlock); + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_dbg(&pdev->dev, "Failed to get IRQ: %d\n", irq); + ret = irq; + goto err_irq; + } + + ret = devm_request_irq(dev, irq, hdq_isr, 0, "omap_hdq", hdq_data); + if (ret < 0) { + dev_dbg(&pdev->dev, "could not request irq\n"); + goto err_irq; + } + + omap_hdq_break(hdq_data); + + pm_runtime_mark_last_busy(&pdev->dev); + pm_runtime_put_autosuspend(&pdev->dev); + + omap_w1_master.data = hdq_data; + + ret = w1_add_master_device(&omap_w1_master); + if (ret) { + dev_dbg(&pdev->dev, "Failure in registering w1 master\n"); + goto err_w1; + } + + return 0; + +err_irq: + pm_runtime_put_sync(&pdev->dev); +err_w1: + pm_runtime_dont_use_autosuspend(&pdev->dev); + pm_runtime_disable(&pdev->dev); + + return ret; +} + +static int omap_hdq_remove(struct platform_device *pdev) +{ + int active; + + active = pm_runtime_get_sync(&pdev->dev); + if (active < 0) + pm_runtime_put_noidle(&pdev->dev); + + w1_remove_master_device(&omap_w1_master); + + pm_runtime_dont_use_autosuspend(&pdev->dev); + if (active >= 0) + pm_runtime_put_sync(&pdev->dev); + pm_runtime_disable(&pdev->dev); + + return 0; +} + +static const struct of_device_id omap_hdq_dt_ids[] = { + { .compatible = "ti,omap3-1w" }, + { .compatible = "ti,am4372-hdq" }, + {} +}; +MODULE_DEVICE_TABLE(of, omap_hdq_dt_ids); + +static struct platform_driver omap_hdq_driver = { + .probe = omap_hdq_probe, + .remove = omap_hdq_remove, + .driver = { + .name = "omap_hdq", + .of_match_table = omap_hdq_dt_ids, + .pm = &omap_hdq_pm_ops, + }, +}; +module_platform_driver(omap_hdq_driver); + +MODULE_AUTHOR("Texas Instruments"); +MODULE_DESCRIPTION("HDQ-1W driver Library"); +MODULE_LICENSE("GPL"); diff --git a/drivers/w1/masters/sgi_w1.c b/drivers/w1/masters/sgi_w1.c new file mode 100644 index 0000000000..d7fbc3c146 --- /dev/null +++ b/drivers/w1/masters/sgi_w1.c @@ -0,0 +1,128 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * sgi_w1.c - w1 master driver for one wire support in SGI ASICs + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +#define MCR_RD_DATA BIT(0) +#define MCR_DONE BIT(1) + +#define MCR_PACK(pulse, sample) (((pulse) << 10) | ((sample) << 2)) + +struct sgi_w1_device { + u32 __iomem *mcr; + struct w1_bus_master bus_master; + char dev_id[64]; +}; + +static u8 sgi_w1_wait(u32 __iomem *mcr) +{ + u32 mcr_val; + + do { + mcr_val = readl(mcr); + } while (!(mcr_val & MCR_DONE)); + + return (mcr_val & MCR_RD_DATA) ? 1 : 0; +} + +/* + * this is the low level routine to + * reset the device on the One Wire interface + * on the hardware + */ +static u8 sgi_w1_reset_bus(void *data) +{ + struct sgi_w1_device *dev = data; + u8 ret; + + writel(MCR_PACK(520, 65), dev->mcr); + ret = sgi_w1_wait(dev->mcr); + udelay(500); /* recovery time */ + return ret; +} + +/* + * this is the low level routine to read/write a bit on the One Wire + * interface on the hardware. It does write 0 if parameter bit is set + * to 0, otherwise a write 1/read. + */ +static u8 sgi_w1_touch_bit(void *data, u8 bit) +{ + struct sgi_w1_device *dev = data; + u8 ret; + + if (bit) + writel(MCR_PACK(6, 13), dev->mcr); + else + writel(MCR_PACK(80, 30), dev->mcr); + + ret = sgi_w1_wait(dev->mcr); + if (bit) + udelay(100); /* recovery */ + return ret; +} + +static int sgi_w1_probe(struct platform_device *pdev) +{ + struct sgi_w1_device *sdev; + struct sgi_w1_platform_data *pdata; + + sdev = devm_kzalloc(&pdev->dev, sizeof(struct sgi_w1_device), + GFP_KERNEL); + if (!sdev) + return -ENOMEM; + + sdev->mcr = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(sdev->mcr)) + return PTR_ERR(sdev->mcr); + + sdev->bus_master.data = sdev; + sdev->bus_master.reset_bus = sgi_w1_reset_bus; + sdev->bus_master.touch_bit = sgi_w1_touch_bit; + + pdata = dev_get_platdata(&pdev->dev); + if (pdata) { + strscpy(sdev->dev_id, pdata->dev_id, sizeof(sdev->dev_id)); + sdev->bus_master.dev_id = sdev->dev_id; + } + + platform_set_drvdata(pdev, sdev); + + return w1_add_master_device(&sdev->bus_master); +} + +/* + * disassociate the w1 device from the driver + */ +static int sgi_w1_remove(struct platform_device *pdev) +{ + struct sgi_w1_device *sdev = platform_get_drvdata(pdev); + + w1_remove_master_device(&sdev->bus_master); + + return 0; +} + +static struct platform_driver sgi_w1_driver = { + .driver = { + .name = "sgi_w1", + }, + .probe = sgi_w1_probe, + .remove = sgi_w1_remove, +}; +module_platform_driver(sgi_w1_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Thomas Bogendoerfer"); +MODULE_DESCRIPTION("Driver for One-Wire IP in SGI ASICs"); diff --git a/drivers/w1/masters/w1-gpio.c b/drivers/w1/masters/w1-gpio.c new file mode 100644 index 0000000000..e45acb6d91 --- /dev/null +++ b/drivers/w1/masters/w1-gpio.c @@ -0,0 +1,204 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * w1-gpio - GPIO w1 bus master driver + * + * Copyright (C) 2007 Ville Syrjala + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +static u8 w1_gpio_set_pullup(void *data, int delay) +{ + struct w1_gpio_platform_data *pdata = data; + + if (delay) { + pdata->pullup_duration = delay; + } else { + if (pdata->pullup_duration) { + /* + * This will OVERRIDE open drain emulation and force-pull + * the line high for some time. + */ + gpiod_set_raw_value(pdata->gpiod, 1); + msleep(pdata->pullup_duration); + /* + * This will simply set the line as input since we are doing + * open drain emulation in the GPIO library. + */ + gpiod_set_value(pdata->gpiod, 1); + } + pdata->pullup_duration = 0; + } + + return 0; +} + +static void w1_gpio_write_bit(void *data, u8 bit) +{ + struct w1_gpio_platform_data *pdata = data; + + gpiod_set_value(pdata->gpiod, bit); +} + +static u8 w1_gpio_read_bit(void *data) +{ + struct w1_gpio_platform_data *pdata = data; + + return gpiod_get_value(pdata->gpiod) ? 1 : 0; +} + +#if defined(CONFIG_OF) +static const struct of_device_id w1_gpio_dt_ids[] = { + { .compatible = "w1-gpio" }, + {} +}; +MODULE_DEVICE_TABLE(of, w1_gpio_dt_ids); +#endif + +static int w1_gpio_probe(struct platform_device *pdev) +{ + struct w1_bus_master *master; + struct w1_gpio_platform_data *pdata; + struct device *dev = &pdev->dev; + struct device_node *np = dev->of_node; + /* Enforce open drain mode by default */ + enum gpiod_flags gflags = GPIOD_OUT_LOW_OPEN_DRAIN; + int err; + + if (of_have_populated_dt()) { + pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); + if (!pdata) + return -ENOMEM; + + /* + * This parameter means that something else than the gpiolib has + * already set the line into open drain mode, so we should just + * driver it high/low like we are in full control of the line and + * open drain will happen transparently. + */ + if (of_property_present(np, "linux,open-drain")) + gflags = GPIOD_OUT_LOW; + + pdev->dev.platform_data = pdata; + } + pdata = dev_get_platdata(dev); + + if (!pdata) { + dev_err(dev, "No configuration data\n"); + return -ENXIO; + } + + master = devm_kzalloc(dev, sizeof(struct w1_bus_master), + GFP_KERNEL); + if (!master) + return -ENOMEM; + + pdata->gpiod = devm_gpiod_get_index(dev, NULL, 0, gflags); + if (IS_ERR(pdata->gpiod)) { + dev_err(dev, "gpio_request (pin) failed\n"); + return PTR_ERR(pdata->gpiod); + } + + pdata->pullup_gpiod = + devm_gpiod_get_index_optional(dev, NULL, 1, GPIOD_OUT_LOW); + if (IS_ERR(pdata->pullup_gpiod)) { + dev_err(dev, "gpio_request_one " + "(ext_pullup_enable_pin) failed\n"); + return PTR_ERR(pdata->pullup_gpiod); + } + + master->data = pdata; + master->read_bit = w1_gpio_read_bit; + gpiod_direction_output(pdata->gpiod, 1); + master->write_bit = w1_gpio_write_bit; + + /* + * If we are using open drain emulation from the GPIO library, + * we need to use this pullup function that hammers the line + * high using a raw accessor to provide pull-up for the w1 + * line. + */ + if (gflags == GPIOD_OUT_LOW_OPEN_DRAIN) + master->set_pullup = w1_gpio_set_pullup; + + err = w1_add_master_device(master); + if (err) { + dev_err(dev, "w1_add_master device failed\n"); + return err; + } + + if (pdata->enable_external_pullup) + pdata->enable_external_pullup(1); + + if (pdata->pullup_gpiod) + gpiod_set_value(pdata->pullup_gpiod, 1); + + platform_set_drvdata(pdev, master); + + return 0; +} + +static int w1_gpio_remove(struct platform_device *pdev) +{ + struct w1_bus_master *master = platform_get_drvdata(pdev); + struct w1_gpio_platform_data *pdata = dev_get_platdata(&pdev->dev); + + if (pdata->enable_external_pullup) + pdata->enable_external_pullup(0); + + if (pdata->pullup_gpiod) + gpiod_set_value(pdata->pullup_gpiod, 0); + + w1_remove_master_device(master); + + return 0; +} + +static int __maybe_unused w1_gpio_suspend(struct device *dev) +{ + struct w1_gpio_platform_data *pdata = dev_get_platdata(dev); + + if (pdata->enable_external_pullup) + pdata->enable_external_pullup(0); + + return 0; +} + +static int __maybe_unused w1_gpio_resume(struct device *dev) +{ + struct w1_gpio_platform_data *pdata = dev_get_platdata(dev); + + if (pdata->enable_external_pullup) + pdata->enable_external_pullup(1); + + return 0; +} + +static SIMPLE_DEV_PM_OPS(w1_gpio_pm_ops, w1_gpio_suspend, w1_gpio_resume); + +static struct platform_driver w1_gpio_driver = { + .driver = { + .name = "w1-gpio", + .pm = &w1_gpio_pm_ops, + .of_match_table = of_match_ptr(w1_gpio_dt_ids), + }, + .probe = w1_gpio_probe, + .remove = w1_gpio_remove, +}; + +module_platform_driver(w1_gpio_driver); + +MODULE_DESCRIPTION("GPIO w1 bus master driver"); +MODULE_AUTHOR("Ville Syrjala "); +MODULE_LICENSE("GPL"); -- cgit v1.2.3