From ace9429bb58fd418f0c81d4c2835699bddf6bde6 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Thu, 11 Apr 2024 10:27:49 +0200 Subject: Adding upstream version 6.6.15. Signed-off-by: Daniel Baumann --- include/sound/sof/dai-intel.h | 205 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 205 insertions(+) create mode 100644 include/sound/sof/dai-intel.h (limited to 'include/sound/sof/dai-intel.h') diff --git a/include/sound/sof/dai-intel.h b/include/sound/sof/dai-intel.h new file mode 100644 index 0000000000..5b93b7292f --- /dev/null +++ b/include/sound/sof/dai-intel.h @@ -0,0 +1,205 @@ +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause) */ +/* + * This file is provided under a dual BSD/GPLv2 license. When using or + * redistributing this file, you may do so under either license. + * + * Copyright(c) 2018 Intel Corporation. All rights reserved. + */ + +#ifndef __INCLUDE_SOUND_SOF_DAI_INTEL_H__ +#define __INCLUDE_SOUND_SOF_DAI_INTEL_H__ + +#include + + /* ssc1: TINTE */ +#define SOF_DAI_INTEL_SSP_QUIRK_TINTE (1 << 0) + /* ssc1: PINTE */ +#define SOF_DAI_INTEL_SSP_QUIRK_PINTE (1 << 1) + /* ssc2: SMTATF */ +#define SOF_DAI_INTEL_SSP_QUIRK_SMTATF (1 << 2) + /* ssc2: MMRATF */ +#define SOF_DAI_INTEL_SSP_QUIRK_MMRATF (1 << 3) + /* ssc2: PSPSTWFDFD */ +#define SOF_DAI_INTEL_SSP_QUIRK_PSPSTWFDFD (1 << 4) + /* ssc2: PSPSRWFDFD */ +#define SOF_DAI_INTEL_SSP_QUIRK_PSPSRWFDFD (1 << 5) +/* ssc1: LBM */ +#define SOF_DAI_INTEL_SSP_QUIRK_LBM (1 << 6) + + /* here is the possibility to define others aux macros */ + +#define SOF_DAI_INTEL_SSP_FRAME_PULSE_WIDTH_MAX 38 +#define SOF_DAI_INTEL_SSP_SLOT_PADDING_MAX 31 + +/* SSP clocks control settings + * + * Macros for clks_control field in sof_ipc_dai_ssp_params struct. + */ + +/* mclk 0 disable */ +#define SOF_DAI_INTEL_SSP_MCLK_0_DISABLE BIT(0) +/* mclk 1 disable */ +#define SOF_DAI_INTEL_SSP_MCLK_1_DISABLE BIT(1) +/* mclk keep active */ +#define SOF_DAI_INTEL_SSP_CLKCTRL_MCLK_KA BIT(2) +/* bclk keep active */ +#define SOF_DAI_INTEL_SSP_CLKCTRL_BCLK_KA BIT(3) +/* fs keep active */ +#define SOF_DAI_INTEL_SSP_CLKCTRL_FS_KA BIT(4) +/* bclk idle */ +#define SOF_DAI_INTEL_SSP_CLKCTRL_BCLK_IDLE_HIGH BIT(5) +/* mclk early start */ +#define SOF_DAI_INTEL_SSP_CLKCTRL_MCLK_ES BIT(6) +/* bclk early start */ +#define SOF_DAI_INTEL_SSP_CLKCTRL_BCLK_ES BIT(7) +/* mclk always on */ +#define SOF_DAI_INTEL_SSP_CLKCTRL_MCLK_AON BIT(8) + +/* DMIC max. four controllers for eight microphone channels */ +#define SOF_DAI_INTEL_DMIC_NUM_CTRL 4 + +/* SSP Configuration Request - SOF_IPC_DAI_SSP_CONFIG */ +struct sof_ipc_dai_ssp_params { + struct sof_ipc_hdr hdr; + uint16_t reserved1; + uint16_t mclk_id; + + uint32_t mclk_rate; /* mclk frequency in Hz */ + uint32_t fsync_rate; /* fsync frequency in Hz */ + uint32_t bclk_rate; /* bclk frequency in Hz */ + + /* TDM */ + uint32_t tdm_slots; + uint32_t rx_slots; + uint32_t tx_slots; + + /* data */ + uint32_t sample_valid_bits; + uint16_t tdm_slot_width; + uint16_t reserved2; /* alignment */ + + /* MCLK */ + uint32_t mclk_direction; + + uint16_t frame_pulse_width; + uint16_t tdm_per_slot_padding_flag; + uint32_t clks_control; + uint32_t quirks; + uint32_t bclk_delay; /* guaranteed time (ms) for which BCLK + * will be driven, before sending data + */ +} __packed; + +/* HDA Configuration Request - SOF_IPC_DAI_HDA_CONFIG */ +struct sof_ipc_dai_hda_params { + struct sof_ipc_hdr hdr; + uint32_t link_dma_ch; + uint32_t rate; + uint32_t channels; +} __packed; + +/* ALH Configuration Request - SOF_IPC_DAI_ALH_CONFIG */ +struct sof_ipc_dai_alh_params { + struct sof_ipc_hdr hdr; + uint32_t stream_id; + uint32_t rate; + uint32_t channels; + + /* reserved for future use */ + uint32_t reserved[13]; +} __packed; + +/* DMIC Configuration Request - SOF_IPC_DAI_DMIC_CONFIG */ + +/* This struct is defined per 2ch PDM controller available in the platform. + * Normally it is sufficient to set the used microphone specific enables to 1 + * and keep other parameters as zero. The customizations are: + * + * 1. If a device mixes different microphones types with different polarity + * and/or the absolute polarity matters the PCM signal from a microphone + * can be inverted with the controls. + * + * 2. If the microphones in a stereo pair do not appear in captured stream + * in desired order due to board schematics choises they can be swapped with + * the clk_edge parameter. + * + * 3. If PDM bit errors are seen in capture (poor quality) the skew parameter + * that delays the sampling time of data by half cycles of DMIC source clock + * can be tried for improvement. However there is no guarantee for this to fix + * data integrity problems. + */ +struct sof_ipc_dai_dmic_pdm_ctrl { + struct sof_ipc_hdr hdr; + uint16_t id; /**< PDM controller ID */ + + uint16_t enable_mic_a; /**< Use A (left) channel mic (0 or 1)*/ + uint16_t enable_mic_b; /**< Use B (right) channel mic (0 or 1)*/ + + uint16_t polarity_mic_a; /**< Optionally invert mic A signal (0 or 1) */ + uint16_t polarity_mic_b; /**< Optionally invert mic B signal (0 or 1) */ + + uint16_t clk_edge; /**< Optionally swap data clock edge (0 or 1) */ + uint16_t skew; /**< Adjust PDM data sampling vs. clock (0..15) */ + + uint16_t reserved[3]; /**< Make sure the total size is 4 bytes aligned */ +} __packed; + +/* This struct contains the global settings for all 2ch PDM controllers. The + * version number used in configuration data is checked vs. version used by + * device driver src/drivers/dmic.c need to match. It is incremented from + * initial value 1 if updates done for the to driver would alter the operation + * of the microphone. + * + * Note: The microphone clock (pdmclk_min, pdmclk_max, duty_min, duty_max) + * parameters need to be set as defined in microphone data sheet. E.g. clock + * range 1.0 - 3.2 MHz is usually supported microphones. Some microphones are + * multi-mode capable and there may be denied mic clock frequencies between + * the modes. In such case set the clock range limits of the desired mode to + * avoid the driver to set clock to an illegal rate. + * + * The duty cycle could be set to 48-52% if not known. Generally these + * parameters can be altered within data sheet specified limits to match + * required audio application performance power. + * + * The microphone clock needs to be usually about 50-80 times the used audio + * sample rate. With highest sample rates above 48 kHz this can relaxed + * somewhat. + * + * The parameter wake_up_time describes how long time the microphone needs + * for the data line to produce valid output from mic clock start. The driver + * will mute the captured audio for the given time. The min_clock_on_time + * parameter is used to prevent too short clock bursts to happen. The driver + * will keep the clock active after capture stop if this time is not yet + * met. The unit for both is microseconds (us). Exceed of 100 ms will be + * treated as an error. + */ +struct sof_ipc_dai_dmic_params { + struct sof_ipc_hdr hdr; + uint32_t driver_ipc_version; /**< Version (1..N) */ + + uint32_t pdmclk_min; /**< Minimum microphone clock in Hz (100000..N) */ + uint32_t pdmclk_max; /**< Maximum microphone clock in Hz (min...N) */ + + uint32_t fifo_fs; /**< FIFO sample rate in Hz (8000..96000) */ + uint32_t reserved_1; /**< Reserved */ + uint16_t fifo_bits; /**< FIFO word length (16 or 32) */ + uint16_t fifo_bits_b; /**< Deprecated since firmware ABI 3.0.1 */ + + uint16_t duty_min; /**< Min. mic clock duty cycle in % (20..80) */ + uint16_t duty_max; /**< Max. mic clock duty cycle in % (min..80) */ + + uint32_t num_pdm_active; /**< Number of active pdm controllers. */ + /**< Range is 1..SOF_DAI_INTEL_DMIC_NUM_CTRL */ + + uint32_t wake_up_time; /**< Time from clock start to data (us) */ + uint32_t min_clock_on_time; /**< Min. time that clk is kept on (us) */ + uint32_t unmute_ramp_time; /**< Length of logarithmic gain ramp (ms) */ + + /* reserved for future use */ + uint32_t reserved[5]; + + /**< PDM controllers configuration */ + struct sof_ipc_dai_dmic_pdm_ctrl pdm[SOF_DAI_INTEL_DMIC_NUM_CTRL]; +} __packed; + +#endif -- cgit v1.2.3