What: /sys/bus/usb/devices/<INTERFACE>/authorized Date: August 2015 Description: This allows to authorize (1) or deauthorize (0) individual interfaces instead a whole device in contrast to the device authorization. If a deauthorized interface will be authorized so the driver probing must be triggered manually by writing INTERFACE to /sys/bus/usb/drivers_probe This allows to avoid side-effects with drivers that need multiple interfaces. A deauthorized interface cannot be probed or claimed. What: /sys/bus/usb/devices/usbX/interface_authorized_default Date: August 2015 Description: This is used as value that determines if interfaces would be authorized by default. The value can be 1 or 0. It's by default 1. What: /sys/bus/usb/device/.../authorized Date: July 2008 KernelVersion: 2.6.26 Contact: David Vrabel <david.vrabel@csr.com> Description: Authorized devices are available for use by device drivers, non-authorized one are not. By default, wired USB devices are authorized. What: /sys/bus/usb/drivers/.../new_id Date: October 2011 Contact: linux-usb@vger.kernel.org Description: Writing a device ID to this file will attempt to dynamically add a new device ID to a USB device driver. This may allow the driver to support more hardware than was included in the driver's static device ID support table at compile time. The format for the device ID is: idVendor idProduct bInterfaceClass RefIdVendor RefIdProduct The vendor ID and device ID fields are required, the rest is optional. The `Ref*` tuple can be used to tell the driver to use the same driver_data for the new device as it is used for the reference device. Upon successfully adding an ID, the driver will probe for the device and attempt to bind to it. For example:: # echo "8086 10f5" > /sys/bus/usb/drivers/foo/new_id Here add a new device (0458:7045) using driver_data from an already supported device (0458:704c):: # echo "0458 7045 0 0458 704c" > /sys/bus/usb/drivers/foo/new_id Reading from this file will list all dynamically added device IDs in the same format, with one entry per line. For example:: # cat /sys/bus/usb/drivers/foo/new_id 8086 10f5 dead beef 06 f00d cafe The list will be truncated at PAGE_SIZE bytes due to sysfs restrictions. What: /sys/bus/usb-serial/drivers/.../new_id Date: October 2011 Contact: linux-usb@vger.kernel.org Description: For serial USB drivers, this attribute appears under the extra bus folder "usb-serial" in sysfs; apart from that difference, all descriptions from the entry "/sys/bus/usb/drivers/.../new_id" apply. What: /sys/bus/usb/drivers/.../remove_id Date: November 2009 Contact: CHENG Renquan <rqcheng@smu.edu.sg> Description: Writing a device ID to this file will remove an ID that was dynamically added via the new_id sysfs entry. The format for the device ID is: idVendor idProduct. After successfully removing an ID, the driver will no longer support the device. This is useful to ensure auto probing won't match the driver to the device. For example: # echo "046d c315" > /sys/bus/usb/drivers/foo/remove_id Reading from this file will list the dynamically added device IDs, exactly like reading from the entry "/sys/bus/usb/drivers/.../new_id" What: /sys/bus/usb/devices/.../power/usb2_hardware_lpm Date: September 2011 Contact: Andiry Xu <andiry.xu@amd.com> Description: If CONFIG_PM is set and a USB 2.0 lpm-capable device is plugged in to a xHCI host which support link PM, it will perform a LPM test; if the test is passed and host supports USB2 hardware LPM (xHCI 1.0 feature), USB2 hardware LPM will be enabled for the device and the USB device directory will contain a file named power/usb2_hardware_lpm. The file holds a string value (enable or disable) indicating whether or not USB2 hardware LPM is enabled for the device. Developer can write y/Y/1 or n/N/0 to the file to enable/disable the feature. What: /sys/bus/usb/devices/.../power/usb3_hardware_lpm_u1 /sys/bus/usb/devices/.../power/usb3_hardware_lpm_u2 Date: November 2015 Contact: Kevin Strasser <kevin.strasser@linux.intel.com> Lu Baolu <baolu.lu@linux.intel.com> Description: If CONFIG_PM is set and a USB 3.0 lpm-capable device is plugged in to a xHCI host which supports link PM, it will check if U1 and U2 exit latencies have been set in the BOS descriptor; if the check is passed and the host supports USB3 hardware LPM, USB3 hardware LPM will be enabled for the device and the USB device directory will contain two files named power/usb3_hardware_lpm_u1 and power/usb3_hardware_lpm_u2. These files hold a string value (enable or disable) indicating whether or not USB3 hardware LPM U1 or U2 is enabled for the device. What: /sys/bus/usb/devices/.../ltm_capable Date: July 2012 Contact: Sarah Sharp <sarah.a.sharp@linux.intel.com> Description: USB 3.0 devices may optionally support Latency Tolerance Messaging (LTM). They indicate their support by setting a bit in the bmAttributes field of their SuperSpeed BOS descriptors. If that bit is set for the device, ltm_capable will read "yes". If the device doesn't support LTM, the file will read "no". The file will be present for all speeds of USB devices, and will always read "no" for USB 1.1 and USB 2.0 devices. What: /sys/bus/usb/devices/<INTERFACE>/wireless_status Date: February 2023 Contact: Bastien Nocera <hadess@hadess.net> Description: Some USB devices use a USB receiver dongle to communicate wirelessly with their device using proprietary protocols. This attribute allows user-space to know whether the device is connected to its receiver dongle, and, for example, consider the device to be absent when choosing whether to show the device's battery, show a headset in a list of outputs, or show an on-screen keyboard if the only wireless keyboard is turned off. This attribute is not to be used to replace protocol specific statuses available in WWAN, WLAN/Wi-Fi, Bluetooth, etc. If the device does not use a receiver dongle with a wireless device, then this attribute will not exist. What: /sys/bus/usb/devices/.../<hub_interface>/port<X> Date: August 2012 Contact: Lan Tianyu <tianyu.lan@intel.com> Description: The /sys/bus/usb/devices/.../<hub_interface>/port<X> is usb port device's sysfs directory. What: /sys/bus/usb/devices/.../<hub_interface>/port<X>/connect_type Date: January 2013 Contact: Lan Tianyu <tianyu.lan@intel.com> Description: Some platforms provide usb port connect types through ACPI. This attribute is to expose these information to user space. The file will read "hotplug", "hardwired" and "not used" if the information is available, and "unknown" otherwise. What: /sys/bus/usb/devices/.../<hub_interface>/port<X>/location Date: October 2018 Contact: Bjørn Mork <bjorn@mork.no> Description: Some platforms provide usb port physical location through firmware. This is used by the kernel to pair up logical ports mapping to the same physical connector. The attribute exposes the raw location value as a hex integer. What: /sys/bus/usb/devices/.../<hub_interface>/port<X>/quirks Date: May 2018 Contact: Nicolas Boichat <drinkcat@chromium.org> Description: In some cases, we care about time-to-active for devices connected on a specific port (e.g. non-standard USB port like pogo pins), where the device to be connected is known in advance, and behaves well according to the specification. This attribute is a bit-field that controls the behavior of a specific port: - Bit 0 of this field selects the "old" enumeration scheme, as it is considerably faster (it only causes one USB reset instead of 2). The old enumeration scheme can also be selected globally using /sys/module/usbcore/parameters/old_scheme_first, but it is often not desirable as the new scheme was introduced to increase compatibility with more devices. - Bit 1 reduces TRSTRCY to the 10 ms that are required by the USB 2.0 specification, instead of the 50 ms that are normally used to help make enumeration work better on some high speed devices. What: /sys/bus/usb/devices/.../<hub_interface>/port<X>/over_current_count Date: February 2018 Contact: Richard Leitner <richard.leitner@skidata.com> Description: Most hubs are able to detect over-current situations on their ports and report them to the kernel. This attribute is to expose the number of over-current situation occurred on a specific port to user space. This file will contain an unsigned 32 bit value which wraps to 0 after its maximum is reached. This file supports poll() for monitoring changes to this value in user space. Any time this value changes the corresponding hub device will send a udev event with the following attributes:: OVER_CURRENT_PORT=/sys/bus/usb/devices/.../<hub_interface>/port<X> OVER_CURRENT_COUNT=[current value of this sysfs attribute] What: /sys/bus/usb/devices/.../<hub_interface>/port<X>/usb3_lpm_permit Date: November 2015 Contact: Lu Baolu <baolu.lu@linux.intel.com> Description: Some USB3.0 devices are not friendly to USB3 LPM. usb3_lpm_permit attribute allows enabling/disabling usb3 lpm of a port. It takes effect both before and after a usb device is enumerated. Supported values are "0" if both u1 and u2 are NOT permitted, "u1" if only u1 is permitted, "u2" if only u2 is permitted, "u1_u2" if both u1 and u2 are permitted. What: /sys/bus/usb/devices/.../<hub_interface>/port<X>/connector Date: December 2021 Contact: Heikki Krogerus <heikki.krogerus@linux.intel.com> Description: Link to the USB Type-C connector when available. This link is only created when USB Type-C Connector Class is enabled, and only if the system firmware is capable of describing the connection between a port and its connector. What: /sys/bus/usb/devices/.../<hub_interface>/port<X>/disable Date: June 2022 Contact: Michael Grzeschik <m.grzeschik@pengutronix.de> Description: This file controls the state of a USB port, including Vbus power output (but only on hubs that support power switching -- most hubs don't support it). If a port is disabled, the port is unusable: Devices attached to the port will not be detected, initialized, or enumerated. What: /sys/bus/usb/devices/.../<hub_interface>/port<X>/early_stop Date: Sep 2022 Contact: Ray Chi <raychi@google.com> Description: Some USB hosts have some watchdog mechanisms so that the device may enter ramdump if it takes a long time during port initialization. This attribute allows each port just has two attempts so that the port initialization will be failed quickly. In addition, if a port which is marked with early_stop has failed to initialize, it will ignore all future connections until this attribute is clear. What: /sys/bus/usb/devices/.../<hub_interface>/port<X>/state Date: June 2023 Contact: Roy Luo <royluo@google.com> Description: Indicates current state of the USB device attached to the port. Valid states are: 'not-attached', 'attached', 'powered', 'reconnecting', 'unauthenticated', 'default', 'addressed', 'configured', and 'suspended'. This file supports poll() to monitor the state change from user space. What: /sys/bus/usb/devices/.../power/usb2_lpm_l1_timeout Date: May 2013 Contact: Mathias Nyman <mathias.nyman@linux.intel.com> Description: USB 2.0 devices may support hardware link power management (LPM) L1 sleep state. The usb2_lpm_l1_timeout attribute allows tuning the timeout for L1 inactivity timer (LPM timer), e.g. needed inactivity time before host requests the device to go to L1 sleep. Useful for power management tuning. Supported values are 0 - 65535 microseconds. What: /sys/bus/usb/devices/.../power/usb2_lpm_besl Date: May 2013 Contact: Mathias Nyman <mathias.nyman@linux.intel.com> Description: USB 2.0 devices that support hardware link power management (LPM) L1 sleep state now use a best effort service latency value (BESL) to indicate the best effort to resumption of service to the device after the initiation of the resume event. If the device does not have a preferred besl value then the host can select one instead. This usb2_lpm_besl attribute allows to tune the host selected besl value in order to tune power saving and service latency. Supported values are 0 - 15. More information on how besl values map to microseconds can be found in USB 2.0 ECN Errata for Link Power Management, section 4.10) What: /sys/bus/usb/devices/.../rx_lanes Date: March 2018 Contact: Mathias Nyman <mathias.nyman@linux.intel.com> Description: Number of rx lanes the device is using. USB 3.2 adds Dual-lane support, 2 rx and 2 tx lanes over Type-C. Inter-Chip SSIC devices support asymmetric lanes up to 4 lanes per direction. Devices before USB 3.2 are single lane (rx_lanes = 1) What: /sys/bus/usb/devices/.../tx_lanes Date: March 2018 Contact: Mathias Nyman <mathias.nyman@linux.intel.com> Description: Number of tx lanes the device is using. USB 3.2 adds Dual-lane support, 2 rx and 2 tx -lanes over Type-C. Inter-Chip SSIC devices support asymmetric lanes up to 4 lanes per direction. Devices before USB 3.2 are single lane (tx_lanes = 1) What: /sys/bus/usb/devices/.../typec Date: November 2023 Contact: Heikki Krogerus <heikki.krogerus@linux.intel.com> Description: Symlink to the USB Type-C partner device. USB Type-C partner represents the component that communicates over the Configuration Channel (CC signal on USB Type-C connectors and cables) with the local port. What: /sys/bus/usb/devices/usbX/bAlternateSetting Description: The current interface alternate setting number, in decimal. See USB specs for its meaning. What: /sys/bus/usb/devices/usbX/bcdDevice Description: The device's release number, in hexadecimal. See USB specs for its meaning. What: /sys/bus/usb/devices/usbX/bConfigurationValue Description: While a USB device typically have just one configuration setting, some devices support multiple configurations. This value shows the current configuration, in decimal. Changing its value will change the device's configuration to another setting. The number of configurations supported by a device is at: /sys/bus/usb/devices/usbX/bNumConfigurations See USB specs for its meaning. What: /sys/bus/usb/devices/usbX/bDeviceClass Description: Class code of the device, in hexadecimal. See USB specs for its meaning. What: /sys/bus/usb/devices/usbX/bDeviceProtocol Description: Protocol code of the device, in hexadecimal. See USB specs for its meaning. What: /sys/bus/usb/devices/usbX/bDeviceSubClass Description: Subclass code of the device, in hexadecimal. See USB specs for its meaning. What: /sys/bus/usb/devices/usbX/bInterfaceClass Description: Class code of the interface, in hexadecimal. See USB specs for its meaning. What: /sys/bus/usb/devices/usbX/bInterfaceNumber Description: Interface number, in hexadecimal. See USB specs for its meaning. What: /sys/bus/usb/devices/usbX/bInterfaceProtocol Description: Protocol code of the interface, in hexadecimal. See USB specs for its meaning. What: /sys/bus/usb/devices/usbX/bInterfaceSubClass Description: Subclass code of the interface, in hexadecimal. See USB specs for its meaning. What: /sys/bus/usb/devices/usbX/bmAttributes Description: Attributes of the current configuration, in hexadecimal. See USB specs for its meaning. What: /sys/bus/usb/devices/usbX/bMaxPacketSize0 Description: Maximum endpoint 0 packet size, in decimal. See USB specs for its meaning. What: /sys/bus/usb/devices/usbX/bMaxPower Description: Maximum power consumption of the active configuration of the device, in miliamperes. What: /sys/bus/usb/devices/usbX/bNumConfigurations Description: Number of the possible configurations of the device, in decimal. The current configuration is controlled via: /sys/bus/usb/devices/usbX/bConfigurationValue See USB specs for its meaning. What: /sys/bus/usb/devices/usbX/bNumEndpoints Description: Number of endpoints used on this interface, in hexadecimal. See USB specs for its meaning. What: /sys/bus/usb/devices/usbX/bNumInterfaces Description: Number of interfaces on this device, in decimal. What: /sys/bus/usb/devices/usbX/busnum Description: Number of the bus. What: /sys/bus/usb/devices/usbX/configuration Description: Contents of the string descriptor associated with the current configuration. It may include the firmware version of a device and/or its serial number. What: /sys/bus/usb/devices/usbX/descriptors Description: Contains the interface descriptors, in binary. What: /sys/bus/usb/devices/usbX/idProduct Description: Product ID, in hexadecimal. What: /sys/bus/usb/devices/usbX/idVendor Description: Vendor ID, in hexadecimal. What: /sys/bus/usb/devices/usbX/devspec Description: Displays the Device Tree Open Firmware node of the interface. What: /sys/bus/usb/devices/usbX/avoid_reset_quirk Description: Most devices have this set to zero. If the value is 1, enable a USB quirk that prevents this device to use reset. (read/write) What: /sys/bus/usb/devices/usbX/devnum Description: USB interface device number, in decimal. What: /sys/bus/usb/devices/usbX/devpath Description: String containing the USB interface device path. What: /sys/bus/usb/devices/usbX/manufacturer Description: Vendor specific string containing the name of the manufacturer of the device. What: /sys/bus/usb/devices/usbX/maxchild Description: Number of ports of an USB hub What: /sys/bus/usb/devices/usbX/persist Description: Keeps the device even if it gets disconnected. What: /sys/bus/usb/devices/usbX/product Description: Vendor specific string containing the name of the device's product. What: /sys/bus/usb/devices/usbX/speed Description: Shows the device's max speed, according to the USB version, in Mbps. Can be: ======= ==================== Unknown speed unknown 1.5 Low speed 15 Full speed 480 High Speed 5000 Super Speed 10000 Super Speed+ 20000 Super Speed+ Gen 2x2 ======= ==================== What: /sys/bus/usb/devices/usbX/supports_autosuspend Description: Returns 1 if the device doesn't support autosuspend. Otherwise, returns 0. What: /sys/bus/usb/devices/usbX/urbnum Description: Number of URBs submitted for the whole device. What: /sys/bus/usb/devices/usbX/version Description: String containing the USB device version, as encoded at the BCD descriptor. What: /sys/bus/usb/devices/usbX/power/autosuspend Description: Time in milliseconds for the device to autosuspend. If the value is negative, then autosuspend is prevented. (read/write) What: /sys/bus/usb/devices/usbX/power/active_duration Description: The total time the device has not been suspended. What: /sys/bus/usb/devices/usbX/power/connected_duration Description: The total time (in msec) that the device has been connected. What: /sys/bus/usb/devices/usbX/power/level Description: What: /sys/bus/usb/devices/usbX/ep_<N>/bEndpointAddress Description: The address of the endpoint described by this descriptor, in hexadecimal. The endpoint direction on this bitmapped field is also shown at: /sys/bus/usb/devices/usbX/ep_<N>/direction See USB specs for its meaning. What: /sys/bus/usb/devices/usbX/ep_<N>/bInterval Description: The interval of the endpoint as described on its descriptor, in hexadecimal. The actual interval depends on the version of the USB. Also shown in time units at /sys/bus/usb/devices/usbX/ep_<N>/interval. What: /sys/bus/usb/devices/usbX/ep_<N>/bLength Description: Number of bytes of the endpoint descriptor, in hexadecimal. What: /sys/bus/usb/devices/usbX/ep_<N>/bmAttributes Description: Attributes which apply to the endpoint as described on its descriptor, in hexadecimal. The endpoint type on this bitmapped field is also shown at: /sys/bus/usb/devices/usbX/ep_<N>/type See USB specs for its meaning. What: /sys/bus/usb/devices/usbX/ep_<N>/direction Description: Direction of the endpoint. Can be: - both (on control endpoints) - in - out What: /sys/bus/usb/devices/usbX/ep_<N>/interval Description: Interval for polling endpoint for data transfers, in milisseconds or microseconds. What: /sys/bus/usb/devices/usbX/ep_<N>/type Description: Descriptor type. Can be: - Control - Isoc - Bulk - Interrupt - unknown What: /sys/bus/usb/devices/usbX/ep_<N>/wMaxPacketSize Description: Maximum packet size this endpoint is capable of sending or receiving, in hexadecimal.