// SPDX-License-Identifier: BSD-3-Clause /* * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. * Copyright (c) 2020-2023, Linaro Limited */ #include #include #include #include #include #include #include #include #include #include #include / { interrupt-parent = <&intc>; #address-cells = <2>; #size-cells = <2>; clocks { xo_board_clk: xo-board { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <38400000>; }; sleep_clk: sleep-clk { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <32764>; clock-output-names = "sleep_clk"; }; }; cpus { #address-cells = <2>; #size-cells = <0>; CPU0: cpu@0 { device_type = "cpu"; compatible = "qcom,kryo485"; reg = <0x0 0x0>; enable-method = "psci"; capacity-dmips-mhz = <602>; next-level-cache = <&L2_0>; qcom,freq-domain = <&cpufreq_hw 0>; operating-points-v2 = <&cpu0_opp_table>; interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>, <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; power-domains = <&CPU_PD0>; power-domain-names = "psci"; #cooling-cells = <2>; clocks = <&cpufreq_hw 0>; L2_0: l2-cache { compatible = "cache"; cache-level = <2>; cache-unified; next-level-cache = <&L3_0>; L3_0: l3-cache { compatible = "cache"; cache-level = <3>; cache-unified; }; }; }; CPU1: cpu@100 { device_type = "cpu"; compatible = "qcom,kryo485"; reg = <0x0 0x100>; enable-method = "psci"; capacity-dmips-mhz = <602>; next-level-cache = <&L2_100>; qcom,freq-domain = <&cpufreq_hw 0>; operating-points-v2 = <&cpu0_opp_table>; interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>, <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; power-domains = <&CPU_PD1>; power-domain-names = "psci"; #cooling-cells = <2>; clocks = <&cpufreq_hw 0>; L2_100: l2-cache { compatible = "cache"; cache-level = <2>; cache-unified; next-level-cache = <&L3_0>; }; }; CPU2: cpu@200 { device_type = "cpu"; compatible = "qcom,kryo485"; reg = <0x0 0x200>; enable-method = "psci"; capacity-dmips-mhz = <602>; next-level-cache = <&L2_200>; qcom,freq-domain = <&cpufreq_hw 0>; operating-points-v2 = <&cpu0_opp_table>; interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>, <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; power-domains = <&CPU_PD2>; power-domain-names = "psci"; #cooling-cells = <2>; clocks = <&cpufreq_hw 0>; L2_200: l2-cache { compatible = "cache"; cache-level = <2>; cache-unified; next-level-cache = <&L3_0>; }; }; CPU3: cpu@300 { device_type = "cpu"; compatible = "qcom,kryo485"; reg = <0x0 0x300>; enable-method = "psci"; capacity-dmips-mhz = <602>; next-level-cache = <&L2_300>; qcom,freq-domain = <&cpufreq_hw 0>; operating-points-v2 = <&cpu0_opp_table>; interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>, <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; power-domains = <&CPU_PD3>; power-domain-names = "psci"; #cooling-cells = <2>; clocks = <&cpufreq_hw 0>; L2_300: l2-cache { compatible = "cache"; cache-unified; cache-level = <2>; next-level-cache = <&L3_0>; }; }; CPU4: cpu@400 { device_type = "cpu"; compatible = "qcom,kryo485"; reg = <0x0 0x400>; enable-method = "psci"; capacity-dmips-mhz = <1024>; next-level-cache = <&L2_400>; qcom,freq-domain = <&cpufreq_hw 1>; operating-points-v2 = <&cpu4_opp_table>; interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>, <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; power-domains = <&CPU_PD4>; power-domain-names = "psci"; #cooling-cells = <2>; clocks = <&cpufreq_hw 1>; L2_400: l2-cache { compatible = "cache"; cache-unified; cache-level = <2>; next-level-cache = <&L3_0>; }; }; CPU5: cpu@500 { device_type = "cpu"; compatible = "qcom,kryo485"; reg = <0x0 0x500>; enable-method = "psci"; capacity-dmips-mhz = <1024>; next-level-cache = <&L2_500>; qcom,freq-domain = <&cpufreq_hw 1>; operating-points-v2 = <&cpu4_opp_table>; interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>, <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; power-domains = <&CPU_PD5>; power-domain-names = "psci"; #cooling-cells = <2>; clocks = <&cpufreq_hw 1>; L2_500: l2-cache { compatible = "cache"; cache-unified; cache-level = <2>; next-level-cache = <&L3_0>; }; }; CPU6: cpu@600 { device_type = "cpu"; compatible = "qcom,kryo485"; reg = <0x0 0x600>; enable-method = "psci"; capacity-dmips-mhz = <1024>; next-level-cache = <&L2_600>; qcom,freq-domain = <&cpufreq_hw 1>; operating-points-v2 = <&cpu4_opp_table>; interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>, <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; power-domains = <&CPU_PD6>; power-domain-names = "psci"; #cooling-cells = <2>; clocks = <&cpufreq_hw 1>; L2_600: l2-cache { compatible = "cache"; cache-unified; cache-level = <2>; next-level-cache = <&L3_0>; }; }; CPU7: cpu@700 { device_type = "cpu"; compatible = "qcom,kryo485"; reg = <0x0 0x700>; enable-method = "psci"; capacity-dmips-mhz = <1024>; next-level-cache = <&L2_700>; qcom,freq-domain = <&cpufreq_hw 1>; operating-points-v2 = <&cpu4_opp_table>; interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>, <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; power-domains = <&CPU_PD7>; power-domain-names = "psci"; #cooling-cells = <2>; clocks = <&cpufreq_hw 1>; L2_700: l2-cache { compatible = "cache"; cache-unified; cache-level = <2>; next-level-cache = <&L3_0>; }; }; cpu-map { cluster0 { core0 { cpu = <&CPU0>; }; core1 { cpu = <&CPU1>; }; core2 { cpu = <&CPU2>; }; core3 { cpu = <&CPU3>; }; core4 { cpu = <&CPU4>; }; core5 { cpu = <&CPU5>; }; core6 { cpu = <&CPU6>; }; core7 { cpu = <&CPU7>; }; }; }; idle-states { entry-method = "psci"; LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 { compatible = "arm,idle-state"; arm,psci-suspend-param = <0x40000004>; entry-latency-us = <355>; exit-latency-us = <909>; min-residency-us = <3934>; local-timer-stop; }; BIG_CPU_SLEEP_0: cpu-sleep-1-0 { compatible = "arm,idle-state"; arm,psci-suspend-param = <0x40000004>; entry-latency-us = <2411>; exit-latency-us = <1461>; min-residency-us = <4488>; local-timer-stop; }; }; domain-idle-states { CLUSTER_SLEEP_APSS_OFF: cluster-sleep-0 { compatible = "domain-idle-state"; arm,psci-suspend-param = <0x41000044>; entry-latency-us = <3300>; exit-latency-us = <3300>; min-residency-us = <6000>; }; CLUSTER_SLEEP_AOSS_SLEEP: cluster-sleep-1 { compatible = "domain-idle-state"; arm,psci-suspend-param = <0x4100a344>; entry-latency-us = <3263>; exit-latency-us = <6562>; min-residency-us = <9987>; }; }; }; cpu0_opp_table: opp-table-cpu0 { compatible = "operating-points-v2"; opp-shared; opp-300000000 { opp-hz = /bits/ 64 <300000000>; opp-peak-kBps = <800000 9600000>; }; opp-422400000 { opp-hz = /bits/ 64 <422400000>; opp-peak-kBps = <800000 9600000>; }; opp-537600000 { opp-hz = /bits/ 64 <537600000>; opp-peak-kBps = <800000 12902400>; }; opp-652800000 { opp-hz = /bits/ 64 <652800000>; opp-peak-kBps = <800000 12902400>; }; opp-768000000 { opp-hz = /bits/ 64 <768000000>; opp-peak-kBps = <800000 15974400>; }; opp-883200000 { opp-hz = /bits/ 64 <883200000>; opp-peak-kBps = <1804000 19660800>; }; opp-998400000 { opp-hz = /bits/ 64 <998400000>; opp-peak-kBps = <1804000 19660800>; }; opp-1113600000 { opp-hz = /bits/ 64 <1113600000>; opp-peak-kBps = <1804000 22732800>; }; opp-1228800000 { opp-hz = /bits/ 64 <1228800000>; opp-peak-kBps = <1804000 22732800>; }; opp-1363200000 { opp-hz = /bits/ 64 <1363200000>; opp-peak-kBps = <2188000 25804800>; }; opp-1478400000 { opp-hz = /bits/ 64 <1478400000>; opp-peak-kBps = <2188000 31948800>; }; opp-1574400000 { opp-hz = /bits/ 64 <1574400000>; opp-peak-kBps = <3072000 31948800>; }; opp-1670400000 { opp-hz = /bits/ 64 <1670400000>; opp-peak-kBps = <3072000 31948800>; }; opp-1766400000 { opp-hz = /bits/ 64 <1766400000>; opp-peak-kBps = <3072000 31948800>; }; }; cpu4_opp_table: opp-table-cpu4 { compatible = "operating-points-v2"; opp-shared; opp-825600000 { opp-hz = /bits/ 64 <825600000>; opp-peak-kBps = <1804000 15974400>; }; opp-940800000 { opp-hz = /bits/ 64 <940800000>; opp-peak-kBps = <2188000 19660800>; }; opp-1056000000 { opp-hz = /bits/ 64 <1056000000>; opp-peak-kBps = <2188000 22732800>; }; opp-1171200000 { opp-hz = /bits/ 64 <1171200000>; opp-peak-kBps = <3072000 25804800>; }; opp-1286400000 { opp-hz = /bits/ 64 <1286400000>; opp-peak-kBps = <3072000 31948800>; }; opp-1420800000 { opp-hz = /bits/ 64 <1420800000>; opp-peak-kBps = <4068000 31948800>; }; opp-1536000000 { opp-hz = /bits/ 64 <1536000000>; opp-peak-kBps = <4068000 31948800>; }; opp-1651200000 { opp-hz = /bits/ 64 <1651200000>; opp-peak-kBps = <4068000 40550400>; }; opp-1766400000 { opp-hz = /bits/ 64 <1766400000>; opp-peak-kBps = <4068000 40550400>; }; opp-1881600000 { opp-hz = /bits/ 64 <1881600000>; opp-peak-kBps = <4068000 43008000>; }; opp-1996800000 { opp-hz = /bits/ 64 <1996800000>; opp-peak-kBps = <6220000 43008000>; }; opp-2131200000 { opp-hz = /bits/ 64 <2131200000>; opp-peak-kBps = <6220000 49152000>; }; opp-2246400000 { opp-hz = /bits/ 64 <2246400000>; opp-peak-kBps = <7216000 49152000>; }; opp-2361600000 { opp-hz = /bits/ 64 <2361600000>; opp-peak-kBps = <8368000 49152000>; }; opp-2457600000 { opp-hz = /bits/ 64 <2457600000>; opp-peak-kBps = <8368000 51609600>; }; opp-2553600000 { opp-hz = /bits/ 64 <2553600000>; opp-peak-kBps = <8368000 51609600>; }; opp-2649600000 { opp-hz = /bits/ 64 <2649600000>; opp-peak-kBps = <8368000 51609600>; }; opp-2745600000 { opp-hz = /bits/ 64 <2745600000>; opp-peak-kBps = <8368000 51609600>; }; opp-2841600000 { opp-hz = /bits/ 64 <2841600000>; opp-peak-kBps = <8368000 51609600>; }; opp-2918400000 { opp-hz = /bits/ 64 <2918400000>; opp-peak-kBps = <8368000 51609600>; }; opp-2995200000 { opp-hz = /bits/ 64 <2995200000>; opp-peak-kBps = <8368000 51609600>; }; }; firmware { scm: scm { compatible = "qcom,scm-sc8180x", "qcom,scm"; }; }; camnoc_virt: interconnect-camnoc-virt { compatible = "qcom,sc8180x-camnoc-virt"; #interconnect-cells = <2>; qcom,bcm-voters = <&apps_bcm_voter>; }; mc_virt: interconnect-mc-virt { compatible = "qcom,sc8180x-mc-virt"; #interconnect-cells = <2>; qcom,bcm-voters = <&apps_bcm_voter>; }; qup_virt: interconnect-qup-virt { compatible = "qcom,sc8180x-qup-virt"; #interconnect-cells = <2>; qcom,bcm-voters = <&apps_bcm_voter>; }; memory@80000000 { device_type = "memory"; /* We expect the bootloader to fill in the size */ reg = <0x0 0x80000000 0x0 0x0>; }; pmu { compatible = "arm,armv8-pmuv3"; interrupts = ; }; psci { compatible = "arm,psci-1.0"; method = "smc"; CPU_PD0: power-domain-cpu0 { #power-domain-cells = <0>; power-domains = <&CLUSTER_PD>; domain-idle-states = <&LITTLE_CPU_SLEEP_0>; }; CPU_PD1: power-domain-cpu1 { #power-domain-cells = <0>; power-domains = <&CLUSTER_PD>; domain-idle-states = <&LITTLE_CPU_SLEEP_0>; }; CPU_PD2: power-domain-cpu2 { #power-domain-cells = <0>; power-domains = <&CLUSTER_PD>; domain-idle-states = <&LITTLE_CPU_SLEEP_0>; }; CPU_PD3: power-domain-cpu3 { #power-domain-cells = <0>; power-domains = <&CLUSTER_PD>; domain-idle-states = <&LITTLE_CPU_SLEEP_0>; }; CPU_PD4: power-domain-cpu4 { #power-domain-cells = <0>; power-domains = <&CLUSTER_PD>; domain-idle-states = <&BIG_CPU_SLEEP_0>; }; CPU_PD5: power-domain-cpu5 { #power-domain-cells = <0>; power-domains = <&CLUSTER_PD>; domain-idle-states = <&BIG_CPU_SLEEP_0>; }; CPU_PD6: power-domain-cpu6 { #power-domain-cells = <0>; power-domains = <&CLUSTER_PD>; domain-idle-states = <&BIG_CPU_SLEEP_0>; }; CPU_PD7: power-domain-cpu7 { #power-domain-cells = <0>; power-domains = <&CLUSTER_PD>; domain-idle-states = <&BIG_CPU_SLEEP_0>; }; CLUSTER_PD: power-domain-cpu-cluster0 { #power-domain-cells = <0>; domain-idle-states = <&CLUSTER_SLEEP_APSS_OFF &CLUSTER_SLEEP_AOSS_SLEEP>; }; }; reserved-memory { #address-cells = <2>; #size-cells = <2>; ranges; hyp_mem: hyp@85700000 { reg = <0x0 0x85700000 0x0 0x600000>; no-map; }; xbl_mem: xbl@85d00000 { reg = <0x0 0x85d00000 0x0 0x140000>; no-map; }; aop_mem: aop@85f00000 { reg = <0x0 0x85f00000 0x0 0x20000>; no-map; }; aop_cmd_db: cmd-db@85f20000 { compatible = "qcom,cmd-db"; reg = <0x0 0x85f20000 0x0 0x20000>; no-map; }; reserved@85f40000 { reg = <0x0 0x85f40000 0x0 0x10000>; no-map; }; smem_mem: smem@86000000 { compatible = "qcom,smem"; reg = <0x0 0x86000000 0x0 0x200000>; no-map; hwlocks = <&tcsr_mutex 3>; }; reserved@86200000 { reg = <0x0 0x86200000 0x0 0x3900000>; no-map; }; reserved@89b00000 { reg = <0x0 0x89b00000 0x0 0x1c00000>; no-map; }; reserved@9d400000 { reg = <0x0 0x9d400000 0x0 0x1000000>; no-map; }; reserved@9e400000 { reg = <0x0 0x9e400000 0x0 0x1400000>; no-map; }; reserved@9f800000 { reg = <0x0 0x9f800000 0x0 0x800000>; no-map; }; }; smp2p-cdsp { compatible = "qcom,smp2p"; qcom,smem = <94>, <432>; interrupts = ; mboxes = <&apss_shared 6>; qcom,local-pid = <0>; qcom,remote-pid = <5>; cdsp_smp2p_out: master-kernel { qcom,entry-name = "master-kernel"; #qcom,smem-state-cells = <1>; }; cdsp_smp2p_in: slave-kernel { qcom,entry-name = "slave-kernel"; interrupt-controller; #interrupt-cells = <2>; }; }; smp2p-lpass { compatible = "qcom,smp2p"; qcom,smem = <443>, <429>; interrupts = ; mboxes = <&apss_shared 10>; qcom,local-pid = <0>; qcom,remote-pid = <2>; adsp_smp2p_out: master-kernel { qcom,entry-name = "master-kernel"; #qcom,smem-state-cells = <1>; }; adsp_smp2p_in: slave-kernel { qcom,entry-name = "slave-kernel"; interrupt-controller; #interrupt-cells = <2>; }; }; smp2p-mpss { compatible = "qcom,smp2p"; qcom,smem = <435>, <428>; interrupts = ; mboxes = <&apss_shared 14>; qcom,local-pid = <0>; qcom,remote-pid = <1>; modem_smp2p_out: master-kernel { qcom,entry-name = "master-kernel"; #qcom,smem-state-cells = <1>; }; modem_smp2p_in: slave-kernel { qcom,entry-name = "slave-kernel"; interrupt-controller; #interrupt-cells = <2>; }; modem_smp2p_ipa_out: ipa-ap-to-modem { qcom,entry-name = "ipa"; #qcom,smem-state-cells = <1>; }; modem_smp2p_ipa_in: ipa-modem-to-ap { qcom,entry-name = "ipa"; interrupt-controller; #interrupt-cells = <2>; }; modem_smp2p_wlan_in: wlan-wpss-to-ap { qcom,entry-name = "wlan"; interrupt-controller; #interrupt-cells = <2>; }; }; smp2p-slpi { compatible = "qcom,smp2p"; qcom,smem = <481>, <430>; interrupts = ; mboxes = <&apss_shared 26>; qcom,local-pid = <0>; qcom,remote-pid = <3>; slpi_smp2p_out: master-kernel { qcom,entry-name = "master-kernel"; #qcom,smem-state-cells = <1>; }; slpi_smp2p_in: slave-kernel { qcom,entry-name = "slave-kernel"; interrupt-controller; #interrupt-cells = <2>; }; }; soc: soc@0 { compatible = "simple-bus"; #address-cells = <2>; #size-cells = <2>; ranges = <0 0 0 0 0x10 0>; dma-ranges = <0 0 0 0 0x10 0>; gcc: clock-controller@100000 { compatible = "qcom,gcc-sc8180x"; reg = <0x0 0x00100000 0x0 0x1f0000>; #clock-cells = <1>; #reset-cells = <1>; #power-domain-cells = <1>; clocks = <&rpmhcc RPMH_CXO_CLK>, <&rpmhcc RPMH_CXO_CLK_A>, <&sleep_clk>; clock-names = "bi_tcxo", "bi_tcxo_ao", "sleep_clk"; power-domains = <&rpmhpd SC8180X_CX>; }; qupv3_id_0: geniqup@8c0000 { compatible = "qcom,geni-se-qup"; reg = <0 0x008c0000 0 0x6000>; clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>, <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>; clock-names = "m-ahb", "s-ahb"; #address-cells = <2>; #size-cells = <2>; ranges; iommus = <&apps_smmu 0x4c3 0>; status = "disabled"; i2c0: i2c@880000 { compatible = "qcom,geni-i2c"; reg = <0 0x00880000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>, <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; spi0: spi@880000 { compatible = "qcom,geni-spi"; reg = <0 0x00880000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>; interconnect-names = "qup-core", "qup-config"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; uart0: serial@880000 { compatible = "qcom,geni-uart"; reg = <0 0x00880000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; }; i2c1: i2c@884000 { compatible = "qcom,geni-i2c"; reg = <0 0x00884000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>, <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; spi1: spi@884000 { compatible = "qcom,geni-spi"; reg = <0 0x00884000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>; interconnect-names = "qup-core", "qup-config"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; uart1: serial@884000 { compatible = "qcom,geni-uart"; reg = <0 0x00884000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; }; i2c2: i2c@888000 { compatible = "qcom,geni-i2c"; reg = <0 0x00888000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>, <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; spi2: spi@888000 { compatible = "qcom,geni-spi"; reg = <0 0x00888000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>; interconnect-names = "qup-core", "qup-config"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; uart2: serial@888000 { compatible = "qcom,geni-uart"; reg = <0 0x00888000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; }; i2c3: i2c@88c000 { compatible = "qcom,geni-i2c"; reg = <0 0x0088c000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>, <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; spi3: spi@88c000 { compatible = "qcom,geni-spi"; reg = <0 0x0088c000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>; interconnect-names = "qup-core", "qup-config"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; uart3: serial@88c000 { compatible = "qcom,geni-uart"; reg = <0 0x0088c000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; }; i2c4: i2c@890000 { compatible = "qcom,geni-i2c"; reg = <0 0x00890000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>, <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; spi4: spi@890000 { compatible = "qcom,geni-spi"; reg = <0 0x00890000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>; interconnect-names = "qup-core", "qup-config"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; uart4: serial@890000 { compatible = "qcom,geni-uart"; reg = <0 0x00890000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; }; i2c5: i2c@894000 { compatible = "qcom,geni-i2c"; reg = <0 0x00894000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>, <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; spi5: spi@894000 { compatible = "qcom,geni-spi"; reg = <0 0x00894000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>; interconnect-names = "qup-core", "qup-config"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; uart5: serial@894000 { compatible = "qcom,geni-uart"; reg = <0 0x00894000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; }; i2c6: i2c@898000 { compatible = "qcom,geni-i2c"; reg = <0 0x00898000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>, <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; spi6: spi@898000 { compatible = "qcom,geni-spi"; reg = <0 0x00898000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>; interconnect-names = "qup-core", "qup-config"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; uart6: serial@898000 { compatible = "qcom,geni-uart"; reg = <0 0x00898000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; }; i2c7: i2c@89c000 { compatible = "qcom,geni-i2c"; reg = <0 0x0089c000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>, <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; spi7: spi@89c000 { compatible = "qcom,geni-spi"; reg = <0 0x0089c000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>; interconnect-names = "qup-core", "qup-config"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; uart7: serial@89c000 { compatible = "qcom,geni-uart"; reg = <0 0x0089c000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; }; }; qupv3_id_1: geniqup@ac0000 { compatible = "qcom,geni-se-qup"; reg = <0x0 0x00ac0000 0x0 0x6000>; clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>, <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>; clock-names = "m-ahb", "s-ahb"; #address-cells = <2>; #size-cells = <2>; ranges; iommus = <&apps_smmu 0x603 0>; status = "disabled"; i2c8: i2c@a80000 { compatible = "qcom,geni-i2c"; reg = <0 0x00a80000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>, <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; spi8: spi@a80000 { compatible = "qcom,geni-spi"; reg = <0 0x00a80000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>; interconnect-names = "qup-core", "qup-config"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; uart8: serial@a80000 { compatible = "qcom,geni-uart"; reg = <0 0x00a80000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; }; i2c9: i2c@a84000 { compatible = "qcom,geni-i2c"; reg = <0 0x00a84000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>, <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; spi9: spi@a84000 { compatible = "qcom,geni-spi"; reg = <0 0x00a84000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>; interconnect-names = "qup-core", "qup-config"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; uart9: serial@a84000 { compatible = "qcom,geni-debug-uart"; reg = <0 0x00a84000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; }; i2c10: i2c@a88000 { compatible = "qcom,geni-i2c"; reg = <0 0x00a88000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>, <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; spi10: spi@a88000 { compatible = "qcom,geni-spi"; reg = <0 0x00a88000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>; interconnect-names = "qup-core", "qup-config"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; uart10: serial@a88000 { compatible = "qcom,geni-uart"; reg = <0 0x00a88000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; }; i2c11: i2c@a8c000 { compatible = "qcom,geni-i2c"; reg = <0 0x00a8c000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>, <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; spi11: spi@a8c000 { compatible = "qcom,geni-spi"; reg = <0 0x00a8c000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>; interconnect-names = "qup-core", "qup-config"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; uart11: serial@a8c000 { compatible = "qcom,geni-uart"; reg = <0 0x00a8c000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; }; i2c12: i2c@a90000 { compatible = "qcom,geni-i2c"; reg = <0 0x00a90000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>, <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; spi12: spi@a90000 { compatible = "qcom,geni-spi"; reg = <0 0x00a90000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>; interconnect-names = "qup-core", "qup-config"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; uart12: serial@a90000 { compatible = "qcom,geni-uart"; reg = <0 0x00a90000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; }; i2c16: i2c@a94000 { compatible = "qcom,geni-i2c"; reg = <0 0x00a94000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>, <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; spi16: spi@a94000 { compatible = "qcom,geni-spi"; reg = <0 0x00a94000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>; interconnect-names = "qup-core", "qup-config"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; uart16: serial@a94000 { compatible = "qcom,geni-uart"; reg = <0 0x00a94000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; }; }; qupv3_id_2: geniqup@cc0000 { compatible = "qcom,geni-se-qup"; reg = <0x0 0x00cc0000 0x0 0x6000>; clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>, <&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>; clock-names = "m-ahb", "s-ahb"; #address-cells = <2>; #size-cells = <2>; ranges; iommus = <&apps_smmu 0x7a3 0>; status = "disabled"; i2c17: i2c@c80000 { compatible = "qcom,geni-i2c"; reg = <0 0x00c80000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>, <&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; spi17: spi@c80000 { compatible = "qcom,geni-spi"; reg = <0 0x00c80000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>; interconnect-names = "qup-core", "qup-config"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; uart17: serial@c80000 { compatible = "qcom,geni-uart"; reg = <0 0x00c80000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; }; i2c18: i2c@c84000 { compatible = "qcom,geni-i2c"; reg = <0 0x00c84000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>, <&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; spi18: spi@c84000 { compatible = "qcom,geni-spi"; reg = <0 0x00c84000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>; interconnect-names = "qup-core", "qup-config"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; uart18: serial@c84000 { compatible = "qcom,geni-uart"; reg = <0 0x00c84000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; }; i2c19: i2c@c88000 { compatible = "qcom,geni-i2c"; reg = <0 0x00c88000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>, <&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; spi19: spi@c88000 { compatible = "qcom,geni-spi"; reg = <0 0x00c88000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>; interconnect-names = "qup-core", "qup-config"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; uart19: serial@c88000 { compatible = "qcom,geni-uart"; reg = <0 0x00c88000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; }; i2c13: i2c@c8c000 { compatible = "qcom,geni-i2c"; reg = <0 0x00c8c000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>, <&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; spi13: spi@c8c000 { compatible = "qcom,geni-spi"; reg = <0 0x00c8c000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>; interconnect-names = "qup-core", "qup-config"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; uart13: serial@c8c000 { compatible = "qcom,geni-uart"; reg = <0 0x00c8c000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; }; i2c14: i2c@c90000 { compatible = "qcom,geni-i2c"; reg = <0 0x00c90000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>, <&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; spi14: spi@c90000 { compatible = "qcom,geni-spi"; reg = <0 0x00c90000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>; interconnect-names = "qup-core", "qup-config"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; uart14: serial@c90000 { compatible = "qcom,geni-uart"; reg = <0 0x00c90000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; }; i2c15: i2c@c94000 { compatible = "qcom,geni-i2c"; reg = <0 0x00c94000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>, <&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; spi15: spi@c94000 { compatible = "qcom,geni-spi"; reg = <0 0x00c94000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>; interconnect-names = "qup-core", "qup-config"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; uart15: serial@c94000 { compatible = "qcom,geni-uart"; reg = <0 0x00c94000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>; clock-names = "se"; interrupts = ; interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; }; }; config_noc: interconnect@1500000 { compatible = "qcom,sc8180x-config-noc"; reg = <0 0x01500000 0 0x7400>; #interconnect-cells = <2>; qcom,bcm-voters = <&apps_bcm_voter>; }; system_noc: interconnect@1620000 { compatible = "qcom,sc8180x-system-noc"; reg = <0 0x01620000 0 0x19400>; #interconnect-cells = <2>; qcom,bcm-voters = <&apps_bcm_voter>; }; aggre1_noc: interconnect@16e0000 { compatible = "qcom,sc8180x-aggre1-noc"; reg = <0 0x016e0000 0 0xd080>; #interconnect-cells = <2>; qcom,bcm-voters = <&apps_bcm_voter>; }; aggre2_noc: interconnect@1700000 { compatible = "qcom,sc8180x-aggre2-noc"; reg = <0 0x01700000 0 0x20000>; #interconnect-cells = <2>; qcom,bcm-voters = <&apps_bcm_voter>; }; compute_noc: interconnect@1720000 { compatible = "qcom,sc8180x-compute-noc"; reg = <0 0x01720000 0 0x7000>; #interconnect-cells = <2>; qcom,bcm-voters = <&apps_bcm_voter>; }; mmss_noc: interconnect@1740000 { compatible = "qcom,sc8180x-mmss-noc"; reg = <0 0x01740000 0 0x1c100>; #interconnect-cells = <2>; qcom,bcm-voters = <&apps_bcm_voter>; }; pcie0: pcie@1c00000 { compatible = "qcom,pcie-sc8180x"; reg = <0 0x01c00000 0 0x3000>, <0 0x60000000 0 0xf1d>, <0 0x60000f20 0 0xa8>, <0 0x60001000 0 0x1000>, <0 0x60100000 0 0x100000>; reg-names = "parf", "dbi", "elbi", "atu", "config"; device_type = "pci"; linux,pci-domain = <0>; bus-range = <0x00 0xff>; num-lanes = <2>; #address-cells = <3>; #size-cells = <2>; ranges = <0x01000000 0x0 0x60200000 0x0 0x60200000 0x0 0x100000>, <0x02000000 0x0 0x60300000 0x0 0x60300000 0x0 0x3d00000>; interrupts = , , , , , , , ; interrupt-names = "msi0", "msi1", "msi2", "msi3", "msi4", "msi5", "msi6", "msi7"; #interrupt-cells = <1>; interrupt-map-mask = <0 0 0 0x7>; interrupt-map = <0 0 0 1 &intc 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ <0 0 0 2 &intc 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ <0 0 0 3 &intc 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ <0 0 0 4 &intc 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ clocks = <&gcc GCC_PCIE_0_PIPE_CLK>, <&gcc GCC_PCIE_0_AUX_CLK>, <&gcc GCC_PCIE_0_CFG_AHB_CLK>, <&gcc GCC_PCIE_0_MSTR_AXI_CLK>, <&gcc GCC_PCIE_0_SLV_AXI_CLK>, <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>, <&gcc GCC_PCIE_0_CLKREF_CLK>, <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>; clock-names = "pipe", "aux", "cfg", "bus_master", "bus_slave", "slave_q2a", "ref", "tbu"; assigned-clocks = <&gcc GCC_PCIE_0_AUX_CLK>; assigned-clock-rates = <19200000>; iommu-map = <0x0 &apps_smmu 0x1d80 0x1>, <0x100 &apps_smmu 0x1d81 0x1>; resets = <&gcc GCC_PCIE_0_BCR>; reset-names = "pci"; power-domains = <&gcc PCIE_0_GDSC>; interconnects = <&aggre2_noc MASTER_PCIE 0 &mc_virt SLAVE_EBI_CH0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_PCIE_0 0>; interconnect-names = "pcie-mem", "cpu-pcie"; phys = <&pcie0_phy>; phy-names = "pciephy"; dma-coherent; status = "disabled"; }; pcie0_phy: phy@1c06000 { compatible = "qcom,sc8180x-qmp-pcie-phy"; reg = <0 0x01c06000 0 0x1000>; clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>, <&gcc GCC_PCIE_0_CFG_AHB_CLK>, <&gcc GCC_PCIE_0_CLKREF_CLK>, <&gcc GCC_PCIE0_PHY_REFGEN_CLK>, <&gcc GCC_PCIE_0_PIPE_CLK>; clock-names = "aux", "cfg_ahb", "ref", "refgen", "pipe"; #clock-cells = <0>; clock-output-names = "pcie_0_pipe_clk"; #phy-cells = <0>; resets = <&gcc GCC_PCIE_0_PHY_BCR>; reset-names = "phy"; assigned-clocks = <&gcc GCC_PCIE0_PHY_REFGEN_CLK>; assigned-clock-rates = <100000000>; status = "disabled"; }; pcie3: pcie@1c08000 { compatible = "qcom,pcie-sc8180x"; reg = <0 0x01c08000 0 0x3000>, <0 0x40000000 0 0xf1d>, <0 0x40000f20 0 0xa8>, <0 0x40001000 0 0x1000>, <0 0x40100000 0 0x100000>; reg-names = "parf", "dbi", "elbi", "atu", "config"; device_type = "pci"; linux,pci-domain = <3>; bus-range = <0x00 0xff>; num-lanes = <2>; #address-cells = <3>; #size-cells = <2>; ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>, <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>; interrupts = , , , , , , , ; interrupt-names = "msi0", "msi1", "msi2", "msi3", "msi4", "msi5", "msi6", "msi7"; #interrupt-cells = <1>; interrupt-map-mask = <0 0 0 0x7>; interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ <0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ <0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ <0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ clocks = <&gcc GCC_PCIE_3_PIPE_CLK>, <&gcc GCC_PCIE_3_AUX_CLK>, <&gcc GCC_PCIE_3_CFG_AHB_CLK>, <&gcc GCC_PCIE_3_MSTR_AXI_CLK>, <&gcc GCC_PCIE_3_SLV_AXI_CLK>, <&gcc GCC_PCIE_3_SLV_Q2A_AXI_CLK>, <&gcc GCC_PCIE_3_CLKREF_CLK>, <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>; clock-names = "pipe", "aux", "cfg", "bus_master", "bus_slave", "slave_q2a", "ref", "tbu"; assigned-clocks = <&gcc GCC_PCIE_3_AUX_CLK>; assigned-clock-rates = <19200000>; iommu-map = <0x0 &apps_smmu 0x1e00 0x1>, <0x100 &apps_smmu 0x1e01 0x1>; resets = <&gcc GCC_PCIE_3_BCR>; reset-names = "pci"; power-domains = <&gcc PCIE_3_GDSC>; interconnects = <&aggre2_noc MASTER_PCIE_3 0 &mc_virt SLAVE_EBI_CH0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_PCIE_0 0>; interconnect-names = "pcie-mem", "cpu-pcie"; phys = <&pcie3_phy>; phy-names = "pciephy"; dma-coherent; status = "disabled"; }; pcie3_phy: phy@1c0c000 { compatible = "qcom,sc8180x-qmp-pcie-phy"; reg = <0 0x01c0c000 0 0x1000>; clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>, <&gcc GCC_PCIE_3_CFG_AHB_CLK>, <&gcc GCC_PCIE_3_CLKREF_CLK>, <&gcc GCC_PCIE3_PHY_REFGEN_CLK>, <&gcc GCC_PCIE_3_PIPE_CLK>; clock-names = "aux", "cfg_ahb", "ref", "refgen", "pipe"; #clock-cells = <0>; clock-output-names = "pcie_3_pipe_clk"; #phy-cells = <0>; resets = <&gcc GCC_PCIE_3_PHY_BCR>; reset-names = "phy"; assigned-clocks = <&gcc GCC_PCIE3_PHY_REFGEN_CLK>; assigned-clock-rates = <100000000>; status = "disabled"; }; pcie1: pcie@1c10000 { compatible = "qcom,pcie-sc8180x"; reg = <0 0x01c10000 0 0x3000>, <0 0x68000000 0 0xf1d>, <0 0x68000f20 0 0xa8>, <0 0x68001000 0 0x1000>, <0 0x68100000 0 0x100000>; reg-names = "parf", "dbi", "elbi", "atu", "config"; device_type = "pci"; linux,pci-domain = <1>; bus-range = <0x00 0xff>; num-lanes = <2>; #address-cells = <3>; #size-cells = <2>; ranges = <0x01000000 0x0 0x68200000 0x0 0x68200000 0x0 0x100000>, <0x02000000 0x0 0x68300000 0x0 0x68300000 0x0 0x3d00000>; interrupts = , , , , , , , ; interrupt-names = "msi0", "msi1", "msi2", "msi3", "msi4", "msi5", "msi6", "msi7"; #interrupt-cells = <1>; interrupt-map-mask = <0 0 0 0x7>; interrupt-map = <0 0 0 1 &intc 0 747 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ <0 0 0 2 &intc 0 746 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ <0 0 0 3 &intc 0 745 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ <0 0 0 4 &intc 0 744 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ clocks = <&gcc GCC_PCIE_1_PIPE_CLK>, <&gcc GCC_PCIE_1_AUX_CLK>, <&gcc GCC_PCIE_1_CFG_AHB_CLK>, <&gcc GCC_PCIE_1_MSTR_AXI_CLK>, <&gcc GCC_PCIE_1_SLV_AXI_CLK>, <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>, <&gcc GCC_PCIE_1_CLKREF_CLK>, <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>; clock-names = "pipe", "aux", "cfg", "bus_master", "bus_slave", "slave_q2a", "ref", "tbu"; assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>; assigned-clock-rates = <19200000>; iommu-map = <0x0 &apps_smmu 0x1c80 0x1>, <0x100 &apps_smmu 0x1c81 0x1>; resets = <&gcc GCC_PCIE_1_BCR>; reset-names = "pci"; power-domains = <&gcc PCIE_1_GDSC>; interconnects = <&aggre2_noc MASTER_PCIE_1 0 &mc_virt SLAVE_EBI_CH0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_PCIE_0 0>; interconnect-names = "pcie-mem", "cpu-pcie"; phys = <&pcie1_phy>; phy-names = "pciephy"; dma-coherent; status = "disabled"; }; pcie1_phy: phy@1c16000 { compatible = "qcom,sc8180x-qmp-pcie-phy"; reg = <0 0x01c16000 0 0x1000>; clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>, <&gcc GCC_PCIE_1_CFG_AHB_CLK>, <&gcc GCC_PCIE_1_CLKREF_CLK>, <&gcc GCC_PCIE1_PHY_REFGEN_CLK>, <&gcc GCC_PCIE_1_PIPE_CLK>; clock-names = "aux", "cfg_ahb", "ref", "refgen", "pipe"; #clock-cells = <0>; clock-output-names = "pcie_1_pipe_clk"; #phy-cells = <0>; resets = <&gcc GCC_PCIE_1_PHY_BCR>; reset-names = "phy"; assigned-clocks = <&gcc GCC_PCIE1_PHY_REFGEN_CLK>; assigned-clock-rates = <100000000>; status = "disabled"; }; pcie2: pcie@1c18000 { compatible = "qcom,pcie-sc8180x"; reg = <0 0x01c18000 0 0x3000>, <0 0x70000000 0 0xf1d>, <0 0x70000f20 0 0xa8>, <0 0x70001000 0 0x1000>, <0 0x70100000 0 0x100000>; reg-names = "parf", "dbi", "elbi", "atu", "config"; device_type = "pci"; linux,pci-domain = <2>; bus-range = <0x00 0xff>; num-lanes = <4>; #address-cells = <3>; #size-cells = <2>; ranges = <0x01000000 0x0 0x70200000 0x0 0x70200000 0x0 0x100000>, <0x02000000 0x0 0x70300000 0x0 0x70300000 0x0 0x3d00000>; interrupts = , , , , , , , ; interrupt-names = "msi0", "msi1", "msi2", "msi3", "msi4", "msi5", "msi6", "msi7"; #interrupt-cells = <1>; interrupt-map-mask = <0 0 0 0x7>; interrupt-map = <0 0 0 1 &intc 0 663 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ <0 0 0 2 &intc 0 662 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ <0 0 0 3 &intc 0 661 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ <0 0 0 4 &intc 0 660 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ clocks = <&gcc GCC_PCIE_2_PIPE_CLK>, <&gcc GCC_PCIE_2_AUX_CLK>, <&gcc GCC_PCIE_2_CFG_AHB_CLK>, <&gcc GCC_PCIE_2_MSTR_AXI_CLK>, <&gcc GCC_PCIE_2_SLV_AXI_CLK>, <&gcc GCC_PCIE_2_SLV_Q2A_AXI_CLK>, <&gcc GCC_PCIE_2_CLKREF_CLK>, <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>; clock-names = "pipe", "aux", "cfg", "bus_master", "bus_slave", "slave_q2a", "ref", "tbu"; assigned-clocks = <&gcc GCC_PCIE_2_AUX_CLK>; assigned-clock-rates = <19200000>; iommu-map = <0x0 &apps_smmu 0x1d00 0x1>, <0x100 &apps_smmu 0x1d01 0x1>; resets = <&gcc GCC_PCIE_2_BCR>; reset-names = "pci"; power-domains = <&gcc PCIE_2_GDSC>; interconnects = <&aggre2_noc MASTER_PCIE_2 0 &mc_virt SLAVE_EBI_CH0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_PCIE_0 0>; interconnect-names = "pcie-mem", "cpu-pcie"; phys = <&pcie2_phy>; phy-names = "pciephy"; dma-coherent; status = "disabled"; }; pcie2_phy: phy@1c1c000 { compatible = "qcom,sc8180x-qmp-pcie-phy"; reg = <0 0x01c1c000 0 0x1000>; clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>, <&gcc GCC_PCIE_2_CFG_AHB_CLK>, <&gcc GCC_PCIE_2_CLKREF_CLK>, <&gcc GCC_PCIE2_PHY_REFGEN_CLK>, <&gcc GCC_PCIE_2_PIPE_CLK>; clock-names = "aux", "cfg_ahb", "ref", "refgen", "pipe"; #clock-cells = <0>; clock-output-names = "pcie_2_pipe_clk"; #phy-cells = <0>; resets = <&gcc GCC_PCIE_2_PHY_BCR>; reset-names = "phy"; assigned-clocks = <&gcc GCC_PCIE2_PHY_REFGEN_CLK>; assigned-clock-rates = <100000000>; status = "disabled"; }; ufs_mem_hc: ufshc@1d84000 { compatible = "qcom,sc8180x-ufshc", "qcom,ufshc", "jedec,ufs-2.0"; reg = <0 0x01d84000 0 0x2500>; interrupts = ; phys = <&ufs_mem_phy>; phy-names = "ufsphy"; lanes-per-direction = <2>; #reset-cells = <1>; resets = <&gcc GCC_UFS_PHY_BCR>; reset-names = "rst"; iommus = <&apps_smmu 0x300 0>; clocks = <&gcc GCC_UFS_PHY_AXI_CLK>, <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>, <&gcc GCC_UFS_PHY_AHB_CLK>, <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>, <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>, <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>, <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>; clock-names = "core_clk", "bus_aggr_clk", "iface_clk", "core_clk_unipro", "ref_clk", "tx_lane0_sync_clk", "rx_lane0_sync_clk", "rx_lane1_sync_clk"; freq-table-hz = <37500000 300000000>, <0 0>, <0 0>, <37500000 300000000>, <0 0>, <0 0>, <0 0>, <0 0>; power-domains = <&gcc UFS_PHY_GDSC>; interconnects = <&aggre1_noc MASTER_UFS_MEM QCOM_ICC_TAG_ALWAYS &mc_virt SLAVE_EBI_CH0 QCOM_ICC_TAG_ALWAYS>, <&gem_noc MASTER_AMPSS_M0 QCOM_ICC_TAG_ALWAYS &config_noc SLAVE_UFS_MEM_0_CFG QCOM_ICC_TAG_ALWAYS>; interconnect-names = "ufs-ddr", "cpu-ufs"; status = "disabled"; }; ufs_mem_phy: phy-wrapper@1d87000 { compatible = "qcom,sc8180x-qmp-ufs-phy"; reg = <0 0x01d87000 0 0x1000>; clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_UFS_PHY_PHY_AUX_CLK>, <&gcc GCC_UFS_MEM_CLKREF_EN>; clock-names = "ref", "ref_aux", "qref"; resets = <&ufs_mem_hc 0>; reset-names = "ufsphy"; #phy-cells = <0>; status = "disabled"; }; ipa_virt: interconnect@1e00000 { compatible = "qcom,sc8180x-ipa-virt"; reg = <0 0x01e00000 0 0x1000>; #interconnect-cells = <2>; qcom,bcm-voters = <&apps_bcm_voter>; }; tcsr_mutex: hwlock@1f40000 { compatible = "qcom,tcsr-mutex"; reg = <0x0 0x01f40000 0x0 0x40000>; #hwlock-cells = <1>; }; gpu: gpu@2c00000 { compatible = "qcom,adreno-680.1", "qcom,adreno"; #stream-id-cells = <16>; reg = <0 0x02c00000 0 0x40000>; reg-names = "kgsl_3d0_reg_memory"; interrupts = ; iommus = <&adreno_smmu 0 0xc01>; operating-points-v2 = <&gpu_opp_table>; interconnects = <&gem_noc MASTER_GRAPHICS_3D 0 &mc_virt SLAVE_EBI_CH0 0>; interconnect-names = "gfx-mem"; qcom,gmu = <&gmu>; #cooling-cells = <2>; status = "disabled"; gpu_opp_table: opp-table { compatible = "operating-points-v2"; opp-514000000 { opp-hz = /bits/ 64 <514000000>; opp-level = ; }; opp-500000000 { opp-hz = /bits/ 64 <500000000>; opp-level = ; }; opp-461000000 { opp-hz = /bits/ 64 <461000000>; opp-level = ; }; opp-405000000 { opp-hz = /bits/ 64 <405000000>; opp-level = ; }; opp-315000000 { opp-hz = /bits/ 64 <315000000>; opp-level = ; }; opp-256000000 { opp-hz = /bits/ 64 <256000000>; opp-level = ; }; opp-177000000 { opp-hz = /bits/ 64 <177000000>; opp-level = ; }; }; }; gmu: gmu@2c6a000 { compatible = "qcom,adreno-gmu-680.1", "qcom,adreno-gmu"; reg = <0 0x02c6a000 0 0x30000>, <0 0x0b290000 0 0x10000>, <0 0x0b490000 0 0x10000>; reg-names = "gmu", "gmu_pdc", "gmu_pdc_seq"; interrupts = , ; interrupt-names = "hfi", "gmu"; clocks = <&gpucc GPU_CC_AHB_CLK>, <&gpucc GPU_CC_CX_GMU_CLK>, <&gpucc GPU_CC_CXO_CLK>, <&gcc GCC_DDRSS_GPU_AXI_CLK>, <&gcc GCC_GPU_MEMNOC_GFX_CLK>; clock-names = "ahb", "gmu", "cxo", "axi", "memnoc"; power-domains = <&gpucc GPU_CX_GDSC>, <&gpucc GPU_GX_GDSC>; power-domain-names = "cx", "gx"; iommus = <&adreno_smmu 5 0xc00>; operating-points-v2 = <&gmu_opp_table>; gmu_opp_table: opp-table { compatible = "operating-points-v2"; opp-200000000 { opp-hz = /bits/ 64 <200000000>; opp-level = ; }; opp-500000000 { opp-hz = /bits/ 64 <500000000>; opp-level = ; }; }; }; gpucc: clock-controller@2c90000 { compatible = "qcom,sc8180x-gpucc"; reg = <0 0x02c90000 0 0x9000>; clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPU_GPLL0_CLK_SRC>, <&gcc GCC_GPU_GPLL0_DIV_CLK_SRC>; clock-names = "bi_tcxo", "gcc_gpu_gpll0_clk_src", "gcc_gpu_gpll0_div_clk_src"; #clock-cells = <1>; #reset-cells = <1>; #power-domain-cells = <1>; }; adreno_smmu: iommu@2ca0000 { compatible = "qcom,sc8180x-smmu-500", "qcom,adreno-smmu", "qcom,smmu-500", "arm,mmu-500"; reg = <0 0x02ca0000 0 0x10000>; #iommu-cells = <2>; #global-interrupts = <1>; interrupts = , , , , , , , , ; clocks = <&gpucc GPU_CC_AHB_CLK>, <&gcc GCC_GPU_MEMNOC_GFX_CLK>, <&gcc GCC_GPU_SNOC_DVM_GFX_CLK>; clock-names = "ahb", "bus", "iface"; power-domains = <&gpucc GPU_CX_GDSC>; }; tlmm: pinctrl@3100000 { compatible = "qcom,sc8180x-tlmm"; reg = <0 0x03100000 0 0x300000>, <0 0x03500000 0 0x700000>, <0 0x03d00000 0 0x300000>; reg-names = "west", "east", "south"; interrupts = ; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; gpio-ranges = <&tlmm 0 0 191>; wakeup-parent = <&pdc>; }; remoteproc_mpss: remoteproc@4080000 { compatible = "qcom,sc8180x-mpss-pas"; reg = <0x0 0x04080000 0x0 0x4040>; interrupts-extended = <&intc GIC_SPI 266 IRQ_TYPE_EDGE_RISING>, <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>, <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>; interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack", "shutdown-ack"; clocks = <&rpmhcc RPMH_CXO_CLK>; clock-names = "xo"; power-domains = <&rpmhpd SC8180X_CX>, <&rpmhpd SC8180X_MSS>; power-domain-names = "cx", "mss"; qcom,qmp = <&aoss_qmp>; qcom,smem-states = <&modem_smp2p_out 0>; qcom,smem-state-names = "stop"; glink-edge { interrupts = ; label = "modem"; qcom,remote-pid = <1>; mboxes = <&apss_shared 12>; }; }; remoteproc_cdsp: remoteproc@8300000 { compatible = "qcom,sc8180x-cdsp-pas"; reg = <0x0 0x08300000 0x0 0x4040>; interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>, <&cdsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, <&cdsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, <&cdsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, <&cdsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack"; clocks = <&rpmhcc RPMH_CXO_CLK>; clock-names = "xo"; power-domains = <&rpmhpd SC8180X_CX>; power-domain-names = "cx"; qcom,qmp = <&aoss_qmp>; qcom,smem-states = <&cdsp_smp2p_out 0>; qcom,smem-state-names = "stop"; status = "disabled"; glink-edge { interrupts = ; label = "cdsp"; qcom,remote-pid = <5>; mboxes = <&apss_shared 4>; }; }; usb_prim_hsphy: phy@88e2000 { compatible = "qcom,sc8180x-usb-hs-phy", "qcom,usb-snps-hs-7nm-phy"; reg = <0 0x088e2000 0 0x400>; clocks = <&rpmhcc RPMH_CXO_CLK>; clock-names = "ref"; resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>; #phy-cells = <0>; status = "disabled"; }; usb_sec_hsphy: phy@88e3000 { compatible = "qcom,sc8180x-usb-hs-phy", "qcom,usb-snps-hs-7nm-phy"; reg = <0 0x088e3000 0 0x400>; clocks = <&rpmhcc RPMH_CXO_CLK>; clock-names = "ref"; resets = <&gcc GCC_QUSB2PHY_SEC_BCR>; #phy-cells = <0>; status = "disabled"; }; usb_prim_qmpphy: phy@88e9000 { compatible = "qcom,sc8180x-qmp-usb3-dp-phy"; reg = <0 0x088e9000 0 0x18c>, <0 0x088e8000 0 0x38>, <0 0x088ea000 0 0x40>; reg-names = "reg-base", "dp_com"; clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>, <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_USB3_PRIM_CLKREF_CLK>, <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>; clock-names = "aux", "ref_clk_src", "ref", "com_aux"; resets = <&gcc GCC_USB3_DP_PHY_PRIM_SP0_BCR>, <&gcc GCC_USB3_PHY_PRIM_SP0_BCR>; reset-names = "phy", "common"; #clock-cells = <1>; #address-cells = <2>; #size-cells = <2>; ranges; status = "disabled"; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; usb_prim_qmpphy_out: endpoint {}; }; port@2 { reg = <2>; usb_prim_qmpphy_dp_in: endpoint {}; }; }; usb_prim_ssphy: usb3-phy@88e9200 { reg = <0 0x088e9200 0 0x200>, <0 0x088e9400 0 0x200>, <0 0x088e9c00 0 0x218>, <0 0x088e9600 0 0x200>, <0 0x088e9800 0 0x200>, <0 0x088e9a00 0 0x100>; #phy-cells = <0>; clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>; clock-names = "pipe0"; clock-output-names = "usb3_prim_phy_pipe_clk_src"; }; usb_prim_dpphy: dp-phy@88ea200 { reg = <0 0x088ea200 0 0x200>, <0 0x088ea400 0 0x200>, <0 0x088eaa00 0 0x200>, <0 0x088ea600 0 0x200>, <0 0x088ea800 0 0x200>; #clock-cells = <1>; #phy-cells = <0>; }; }; usb_sec_qmpphy: phy@88ee000 { compatible = "qcom,sc8180x-qmp-usb3-dp-phy"; reg = <0 0x088ee000 0 0x18c>, <0 0x088ed000 0 0x10>, <0 0x088ef000 0 0x40>; reg-names = "reg-base", "dp_com"; clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>, <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_USB3_SEC_CLKREF_CLK>, <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>; clock-names = "aux", "ref_clk_src", "ref", "com_aux"; resets = <&gcc GCC_USB3_DP_PHY_SEC_BCR>, <&gcc GCC_USB3_PHY_SEC_BCR>; reset-names = "phy", "common"; #clock-cells = <1>; #address-cells = <2>; #size-cells = <2>; ranges; status = "disabled"; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; usb_sec_qmpphy_out: endpoint {}; }; port@2 { reg = <2>; usb_sec_qmpphy_dp_in: endpoint {}; }; }; usb_sec_ssphy: usb3-phy@88e9200 { reg = <0 0x088ee200 0 0x200>, <0 0x088ee400 0 0x200>, <0 0x088eec00 0 0x218>, <0 0x088ee600 0 0x200>, <0 0x088ee800 0 0x200>, <0 0x088eea00 0 0x100>; #phy-cells = <0>; clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>; clock-names = "pipe0"; clock-output-names = "usb3_sec_phy_pipe_clk_src"; }; usb_sec_dpphy: dp-phy@88ef200 { reg = <0 0x088ef200 0 0x200>, <0 0x088ef400 0 0x200>, <0 0x088efa00 0 0x200>, <0 0x088ef600 0 0x200>, <0 0x088ef800 0 0x200>; #clock-cells = <1>; #phy-cells = <0>; clock-output-names = "qmp_dptx1_phy_pll_link_clk", "qmp_dptx1_phy_pll_vco_div_clk"; }; }; system-cache-controller@9200000 { compatible = "qcom,sc8180x-llcc"; reg = <0 0x09200000 0 0x58000>, <0 0x09280000 0 0x58000>, <0 0x09300000 0 0x58000>, <0 0x09380000 0 0x58000>, <0 0x09400000 0 0x58000>, <0 0x09480000 0 0x58000>, <0 0x09500000 0 0x58000>, <0 0x09580000 0 0x58000>, <0 0x09600000 0 0x58000>; reg-names = "llcc0_base", "llcc1_base", "llcc2_base", "llcc3_base", "llcc4_base", "llcc5_base", "llcc6_base", "llcc7_base", "llcc_broadcast_base"; interrupts = ; }; gem_noc: interconnect@9680000 { compatible = "qcom,sc8180x-gem-noc"; reg = <0 0x09680000 0 0x58200>; #interconnect-cells = <2>; qcom,bcm-voters = <&apps_bcm_voter>; }; usb_prim: usb@a6f8800 { compatible = "qcom,sc8180x-dwc3", "qcom,dwc3"; reg = <0 0x0a6f8800 0 0x400>; interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, <&pdc 6 IRQ_TYPE_LEVEL_HIGH>, <&pdc 8 IRQ_TYPE_EDGE_BOTH>, <&pdc 9 IRQ_TYPE_EDGE_BOTH>; interrupt-names = "hs_phy_irq", "ss_phy_irq", "dm_hs_phy_irq", "dp_hs_phy_irq"; clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>, <&gcc GCC_USB30_PRIM_MASTER_CLK>, <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>, <&gcc GCC_USB30_PRIM_SLEEP_CLK>, <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, <&gcc GCC_USB3_SEC_CLKREF_CLK>; clock-names = "cfg_noc", "core", "iface", "sleep", "mock_utmi", "xo"; resets = <&gcc GCC_USB30_PRIM_BCR>; power-domains = <&gcc USB30_PRIM_GDSC>; interconnects = <&aggre1_noc MASTER_USB3 0 &mc_virt SLAVE_EBI_CH0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_USB3 0>; interconnect-names = "usb-ddr", "apps-usb"; assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, <&gcc GCC_USB30_PRIM_MASTER_CLK>; assigned-clock-rates = <19200000>, <200000000>; #address-cells = <2>; #size-cells = <2>; ranges; dma-ranges; status = "disabled"; usb_prim_dwc3: usb@a600000 { compatible = "snps,dwc3"; reg = <0 0x0a600000 0 0xcd00>; interrupts = ; iommus = <&apps_smmu 0x140 0>; snps,dis_u2_susphy_quirk; snps,dis_enblslpm_quirk; phys = <&usb_prim_hsphy>, <&usb_prim_ssphy>; phy-names = "usb2-phy", "usb3-phy"; port { usb_prim_role_switch: endpoint { }; }; }; }; usb_sec: usb@a8f8800 { compatible = "qcom,sc8180x-dwc3", "qcom,dwc3"; reg = <0 0x0a8f8800 0 0x400>; clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>, <&gcc GCC_USB30_SEC_MASTER_CLK>, <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>, <&gcc GCC_USB30_SEC_SLEEP_CLK>, <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>, <&gcc GCC_USB3_SEC_CLKREF_CLK>; clock-names = "cfg_noc", "core", "iface", "sleep", "mock_utmi", "xo"; resets = <&gcc GCC_USB30_SEC_BCR>; power-domains = <&gcc USB30_SEC_GDSC>; interrupts-extended = <&intc GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>, <&pdc 40 IRQ_TYPE_LEVEL_HIGH>, <&pdc 10 IRQ_TYPE_EDGE_BOTH>, <&pdc 11 IRQ_TYPE_EDGE_BOTH>; interrupt-names = "hs_phy_irq", "ss_phy_irq", "dm_hs_phy_irq", "dp_hs_phy_irq"; assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>, <&gcc GCC_USB30_SEC_MASTER_CLK>; assigned-clock-rates = <19200000>, <200000000>; interconnects = <&aggre1_noc MASTER_USB3_1 0 &mc_virt SLAVE_EBI_CH0 0>, <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_USB3_1 0>; interconnect-names = "usb-ddr", "apps-usb"; #address-cells = <2>; #size-cells = <2>; ranges; dma-ranges; status = "disabled"; usb_sec_dwc3: usb@a800000 { compatible = "snps,dwc3"; reg = <0 0x0a800000 0 0xcd00>; interrupts = ; iommus = <&apps_smmu 0x160 0>; snps,dis_u2_susphy_quirk; snps,dis_enblslpm_quirk; phys = <&usb_sec_hsphy>, <&usb_sec_ssphy>; phy-names = "usb2-phy", "usb3-phy"; port { usb_sec_role_switch: endpoint { }; }; }; }; mdss: mdss@ae00000 { compatible = "qcom,sc8180x-mdss"; reg = <0 0x0ae00000 0 0x1000>; reg-names = "mdss"; power-domains = <&dispcc MDSS_GDSC>; clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, <&gcc GCC_DISP_HF_AXI_CLK>, <&gcc GCC_DISP_SF_AXI_CLK>, <&dispcc DISP_CC_MDSS_MDP_CLK>; clock-names = "iface", "bus", "nrt_bus", "core"; resets = <&dispcc DISP_CC_MDSS_CORE_BCR>; interrupts = ; interrupt-controller; #interrupt-cells = <1>; interconnects = <&mmss_noc MASTER_MDP_PORT0 QCOM_ICC_TAG_ALWAYS &mc_virt SLAVE_EBI_CH0 QCOM_ICC_TAG_ALWAYS>, <&mmss_noc MASTER_MDP_PORT1 QCOM_ICC_TAG_ALWAYS &mc_virt SLAVE_EBI_CH0 QCOM_ICC_TAG_ALWAYS>, <&gem_noc MASTER_AMPSS_M0 QCOM_ICC_TAG_ALWAYS &config_noc SLAVE_DISPLAY_CFG QCOM_ICC_TAG_ALWAYS>; interconnect-names = "mdp0-mem", "mdp1-mem", "cpu-cfg"; iommus = <&apps_smmu 0x800 0x420>; #address-cells = <2>; #size-cells = <2>; ranges; status = "disabled"; mdss_mdp: mdp@ae01000 { compatible = "qcom,sc8180x-dpu"; reg = <0 0x0ae01000 0 0x8f000>, <0 0x0aeb0000 0 0x2008>; reg-names = "mdp", "vbif"; clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, <&gcc GCC_DISP_HF_AXI_CLK>, <&dispcc DISP_CC_MDSS_MDP_CLK>, <&dispcc DISP_CC_MDSS_VSYNC_CLK>, <&dispcc DISP_CC_MDSS_ROT_CLK>, <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>; clock-names = "iface", "bus", "core", "vsync", "rot", "lut"; assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>; assigned-clock-rates = <19200000>; operating-points-v2 = <&mdp_opp_table>; power-domains = <&rpmhpd SC8180X_MMCX>; interrupt-parent = <&mdss>; interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; dpu_intf0_out: endpoint { remote-endpoint = <&dp0_in>; }; }; port@1 { reg = <1>; dpu_intf1_out: endpoint { remote-endpoint = <&mdss_dsi0_in>; }; }; port@2 { reg = <2>; dpu_intf2_out: endpoint { remote-endpoint = <&mdss_dsi1_in>; }; }; port@4 { reg = <4>; dpu_intf4_out: endpoint { remote-endpoint = <&dp1_in>; }; }; port@5 { reg = <5>; dpu_intf5_out: endpoint { remote-endpoint = <&edp_in>; }; }; }; mdp_opp_table: opp-table { compatible = "operating-points-v2"; opp-200000000 { opp-hz = /bits/ 64 <200000000>; required-opps = <&rpmhpd_opp_low_svs>; }; opp-300000000 { opp-hz = /bits/ 64 <300000000>; required-opps = <&rpmhpd_opp_svs>; }; opp-345000000 { opp-hz = /bits/ 64 <345000000>; required-opps = <&rpmhpd_opp_svs_l1>; }; opp-460000000 { opp-hz = /bits/ 64 <460000000>; required-opps = <&rpmhpd_opp_nom>; }; }; }; mdss_dsi0: dsi@ae94000 { compatible = "qcom,mdss-dsi-ctrl"; reg = <0 0x0ae94000 0 0x400>; reg-names = "dsi_ctrl"; interrupt-parent = <&mdss>; interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>, <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, <&dispcc DISP_CC_MDSS_PCLK0_CLK>, <&dispcc DISP_CC_MDSS_ESC0_CLK>, <&dispcc DISP_CC_MDSS_AHB_CLK>, <&gcc GCC_DISP_HF_AXI_CLK>; clock-names = "byte", "byte_intf", "pixel", "core", "iface", "bus"; operating-points-v2 = <&dsi_opp_table>; power-domains = <&rpmhpd SC8180X_MMCX>; phys = <&mdss_dsi0_phy>; phy-names = "dsi"; status = "disabled"; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; mdss_dsi0_in: endpoint { remote-endpoint = <&dpu_intf1_out>; }; }; port@1 { reg = <1>; mdss_dsi0_out: endpoint { }; }; }; dsi_opp_table: opp-table { compatible = "operating-points-v2"; opp-187500000 { opp-hz = /bits/ 64 <187500000>; required-opps = <&rpmhpd_opp_low_svs>; }; opp-300000000 { opp-hz = /bits/ 64 <300000000>; required-opps = <&rpmhpd_opp_svs>; }; opp-358000000 { opp-hz = /bits/ 64 <358000000>; required-opps = <&rpmhpd_opp_svs_l1>; }; }; }; mdss_dsi0_phy: dsi-phy@ae94400 { compatible = "qcom,dsi-phy-7nm"; reg = <0 0x0ae94400 0 0x200>, <0 0x0ae94600 0 0x280>, <0 0x0ae94900 0 0x260>; reg-names = "dsi_phy", "dsi_phy_lane", "dsi_pll"; #clock-cells = <1>; #phy-cells = <0>; clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, <&rpmhcc RPMH_CXO_CLK>; clock-names = "iface", "ref"; status = "disabled"; }; mdss_dsi1: dsi@ae96000 { compatible = "qcom,mdss-dsi-ctrl"; reg = <0 0x0ae96000 0 0x400>; reg-names = "dsi_ctrl"; interrupt-parent = <&mdss>; interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>, <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>, <&dispcc DISP_CC_MDSS_PCLK1_CLK>, <&dispcc DISP_CC_MDSS_ESC1_CLK>, <&dispcc DISP_CC_MDSS_AHB_CLK>, <&gcc GCC_DISP_HF_AXI_CLK>; clock-names = "byte", "byte_intf", "pixel", "core", "iface", "bus"; operating-points-v2 = <&dsi_opp_table>; power-domains = <&rpmhpd SC8180X_MMCX>; phys = <&mdss_dsi1_phy>; phy-names = "dsi"; status = "disabled"; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; mdss_dsi1_in: endpoint { remote-endpoint = <&dpu_intf2_out>; }; }; port@1 { reg = <1>; mdss_dsi1_out: endpoint { }; }; }; }; mdss_dsi1_phy: dsi-phy@ae96400 { compatible = "qcom,dsi-phy-7nm"; reg = <0 0x0ae96400 0 0x200>, <0 0x0ae96600 0 0x280>, <0 0x0ae96900 0 0x260>; reg-names = "dsi_phy", "dsi_phy_lane", "dsi_pll"; #clock-cells = <1>; #phy-cells = <0>; clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, <&rpmhcc RPMH_CXO_CLK>; clock-names = "iface", "ref"; status = "disabled"; }; mdss_dp0: displayport-controller@ae90000 { compatible = "qcom,sc8180x-dp"; reg = <0 0xae90000 0 0x200>, <0 0xae90200 0 0x200>, <0 0xae90400 0 0x600>, <0 0xae90a00 0 0x400>; interrupt-parent = <&mdss>; interrupts = <12>; clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, <&dispcc DISP_CC_MDSS_DP_AUX_CLK>, <&dispcc DISP_CC_MDSS_DP_LINK_CLK>, <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>, <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>; clock-names = "core_iface", "core_aux", "ctrl_link", "ctrl_link_iface", "stream_pixel"; assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>, <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>; assigned-clock-parents = <&usb_prim_dpphy 0>, <&usb_prim_dpphy 1>; phys = <&usb_prim_dpphy>; phy-names = "dp"; #sound-dai-cells = <0>; operating-points-v2 = <&dp0_opp_table>; power-domains = <&rpmhpd SC8180X_MMCX>; status = "disabled"; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; dp0_in: endpoint { remote-endpoint = <&dpu_intf0_out>; }; }; port@1 { reg = <1>; mdss_dp0_out: endpoint { }; }; }; dp0_opp_table: opp-table { compatible = "operating-points-v2"; opp-160000000 { opp-hz = /bits/ 64 <160000000>; required-opps = <&rpmhpd_opp_low_svs>; }; opp-270000000 { opp-hz = /bits/ 64 <270000000>; required-opps = <&rpmhpd_opp_svs>; }; opp-540000000 { opp-hz = /bits/ 64 <540000000>; required-opps = <&rpmhpd_opp_svs_l1>; }; opp-810000000 { opp-hz = /bits/ 64 <810000000>; required-opps = <&rpmhpd_opp_nom>; }; }; }; mdss_dp1: displayport-controller@ae98000 { compatible = "qcom,sc8180x-dp"; reg = <0 0xae98000 0 0x200>, <0 0xae98200 0 0x200>, <0 0xae98400 0 0x600>, <0 0xae98a00 0 0x400>; interrupt-parent = <&mdss>; interrupts = <13>; clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, <&dispcc DISP_CC_MDSS_DP_AUX1_CLK>, <&dispcc DISP_CC_MDSS_DP_LINK1_CLK>, <&dispcc DISP_CC_MDSS_DP_LINK1_INTF_CLK>, <&dispcc DISP_CC_MDSS_DP_PIXEL2_CLK>; clock-names = "core_iface", "core_aux", "ctrl_link", "ctrl_link_iface", "stream_pixel"; assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK1_CLK_SRC>, <&dispcc DISP_CC_MDSS_DP_PIXEL2_CLK_SRC>; assigned-clock-parents = <&usb_sec_dpphy 0>, <&usb_sec_dpphy 1>; phys = <&usb_sec_dpphy>; phy-names = "dp"; #sound-dai-cells = <0>; operating-points-v2 = <&dp0_opp_table>; power-domains = <&rpmhpd SC8180X_MMCX>; status = "disabled"; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; dp1_in: endpoint { remote-endpoint = <&dpu_intf4_out>; }; }; port@1 { reg = <1>; mdss_dp1_out: endpoint { }; }; }; dp1_opp_table: opp-table { compatible = "operating-points-v2"; opp-160000000 { opp-hz = /bits/ 64 <160000000>; required-opps = <&rpmhpd_opp_low_svs>; }; opp-270000000 { opp-hz = /bits/ 64 <270000000>; required-opps = <&rpmhpd_opp_svs>; }; opp-540000000 { opp-hz = /bits/ 64 <540000000>; required-opps = <&rpmhpd_opp_svs_l1>; }; opp-810000000 { opp-hz = /bits/ 64 <810000000>; required-opps = <&rpmhpd_opp_nom>; }; }; }; mdss_edp: displayport-controller@ae9a000 { compatible = "qcom,sc8180x-edp"; reg = <0 0xae9a000 0 0x200>, <0 0xae9a200 0 0x200>, <0 0xae9a400 0 0x600>, <0 0xae9aa00 0 0x400>; interrupt-parent = <&mdss>; interrupts = <14>; clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, <&dispcc DISP_CC_MDSS_EDP_AUX_CLK>, <&dispcc DISP_CC_MDSS_EDP_LINK_CLK>, <&dispcc DISP_CC_MDSS_EDP_LINK_INTF_CLK>, <&dispcc DISP_CC_MDSS_EDP_PIXEL_CLK>; clock-names = "core_iface", "core_aux", "ctrl_link", "ctrl_link_iface", "stream_pixel"; assigned-clocks = <&dispcc DISP_CC_MDSS_EDP_LINK_CLK_SRC>, <&dispcc DISP_CC_MDSS_EDP_PIXEL_CLK_SRC>; assigned-clock-parents = <&edp_phy 0>, <&edp_phy 1>; phys = <&edp_phy>; phy-names = "dp"; operating-points-v2 = <&edp_opp_table>; power-domains = <&rpmhpd SC8180X_MMCX>; status = "disabled"; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; edp_in: endpoint { remote-endpoint = <&dpu_intf5_out>; }; }; }; edp_opp_table: opp-table { compatible = "operating-points-v2"; opp-160000000 { opp-hz = /bits/ 64 <160000000>; required-opps = <&rpmhpd_opp_low_svs>; }; opp-270000000 { opp-hz = /bits/ 64 <270000000>; required-opps = <&rpmhpd_opp_svs>; }; opp-540000000 { opp-hz = /bits/ 64 <540000000>; required-opps = <&rpmhpd_opp_svs_l1>; }; opp-810000000 { opp-hz = /bits/ 64 <810000000>; required-opps = <&rpmhpd_opp_nom>; }; }; }; }; edp_phy: phy@aec2a00 { compatible = "qcom,sc8180x-edp-phy"; reg = <0 0x0aec2a00 0 0x1c0>, <0 0x0aec2200 0 0xa0>, <0 0x0aec2600 0 0xa0>, <0 0x0aec2000 0 0x19c>; clocks = <&dispcc DISP_CC_MDSS_EDP_AUX_CLK>, <&dispcc DISP_CC_MDSS_AHB_CLK>; clock-names = "aux", "cfg_ahb"; power-domains = <&rpmhpd SC8180X_MX>; #clock-cells = <1>; #phy-cells = <0>; }; dispcc: clock-controller@af00000 { compatible = "qcom,sc8180x-dispcc"; reg = <0 0x0af00000 0 0x20000>; clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>, <&usb_prim_dpphy 0>, <&usb_prim_dpphy 1>, <&usb_sec_dpphy 0>, <&usb_sec_dpphy 1>, <&edp_phy 0>, <&edp_phy 1>; clock-names = "bi_tcxo", "sleep_clk", "dp_phy_pll_link_clk", "dp_phy_pll_vco_div_clk", "dptx1_phy_pll_link_clk", "dptx1_phy_pll_vco_div_clk", "edp_phy_pll_link_clk", "edp_phy_pll_vco_div_clk"; power-domains = <&rpmhpd SC8180X_MMCX>; required-opps = <&rpmhpd_opp_low_svs>; #clock-cells = <1>; #reset-cells = <1>; #power-domain-cells = <1>; }; pdc: interrupt-controller@b220000 { compatible = "qcom,sc8180x-pdc", "qcom,pdc"; reg = <0 0x0b220000 0 0x30000>; qcom,pdc-ranges = <0 480 94>, <94 609 31>; #interrupt-cells = <2>; interrupt-parent = <&intc>; interrupt-controller; }; tsens0: thermal-sensor@c263000 { compatible = "qcom,sc8180x-tsens", "qcom,tsens-v2"; reg = <0 0x0c263000 0 0x1ff>, /* TM */ <0 0x0c222000 0 0x1ff>; /* SROT */ #qcom,sensors = <16>; interrupts = , ; interrupt-names = "uplow", "critical"; #thermal-sensor-cells = <1>; }; tsens1: thermal-sensor@c265000 { compatible = "qcom,sc8180x-tsens", "qcom,tsens-v2"; reg = <0 0x0c265000 0 0x1ff>, /* TM */ <0 0x0c223000 0 0x1ff>; /* SROT */ #qcom,sensors = <9>; interrupts = , ; interrupt-names = "uplow", "critical"; #thermal-sensor-cells = <1>; }; aoss_qmp: power-controller@c300000 { compatible = "qcom,sc8180x-aoss-qmp", "qcom,aoss-qmp"; reg = <0x0 0x0c300000 0x0 0x400>; interrupts = ; mboxes = <&apss_shared 0>; #clock-cells = <0>; #power-domain-cells = <1>; }; sram@c3f0000 { compatible = "qcom,rpmh-stats"; reg = <0x0 0x0c3f0000 0x0 0x400>; }; spmi_bus: spmi@c440000 { compatible = "qcom,spmi-pmic-arb"; reg = <0x0 0x0c440000 0x0 0x0001100>, <0x0 0x0c600000 0x0 0x2000000>, <0x0 0x0e600000 0x0 0x0100000>, <0x0 0x0e700000 0x0 0x00a0000>, <0x0 0x0c40a000 0x0 0x0026000>; reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; interrupt-names = "periph_irq"; interrupts = ; qcom,ee = <0>; qcom,channel = <0>; #address-cells = <2>; #size-cells = <0>; interrupt-controller; #interrupt-cells = <4>; }; apps_smmu: iommu@15000000 { compatible = "qcom,sc8180x-smmu-500", "arm,mmu-500"; reg = <0 0x15000000 0 0x100000>; #iommu-cells = <2>; #global-interrupts = <1>; interrupts = , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ; }; remoteproc_adsp: remoteproc@17300000 { compatible = "qcom,sc8180x-adsp-pas"; reg = <0x0 0x17300000 0x0 0x4040>; interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>, <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack"; clocks = <&rpmhcc RPMH_CXO_CLK>; clock-names = "xo"; power-domains = <&rpmhpd SC8180X_CX>; power-domain-names = "cx"; qcom,qmp = <&aoss_qmp>; qcom,smem-states = <&adsp_smp2p_out 0>; qcom,smem-state-names = "stop"; status = "disabled"; remoteproc_adsp_glink: glink-edge { interrupts = ; label = "lpass"; qcom,remote-pid = <2>; mboxes = <&apss_shared 8>; }; }; intc: interrupt-controller@17a00000 { compatible = "arm,gic-v3"; interrupt-controller; #interrupt-cells = <3>; reg = <0x0 0x17a00000 0x0 0x10000>, /* GICD */ <0x0 0x17a60000 0x0 0x100000>; /* GICR * 8 */ interrupts = ; #redistributor-regions = <1>; redistributor-stride = <0 0x20000>; }; apss_shared: mailbox@17c00000 { compatible = "qcom,sc8180x-apss-shared", "qcom,sdm845-apss-shared"; reg = <0x0 0x17c00000 0x0 0x1000>; #mbox-cells = <1>; }; timer@17c20000 { compatible = "arm,armv7-timer-mem"; reg = <0x0 0x17c20000 0x0 0x1000>; #address-cells = <1>; #size-cells = <1>; ranges = <0 0 0 0x20000000>; frame@17c21000 { reg = <0x17c21000 0x1000>, <0x17c22000 0x1000>; frame-number = <0>; interrupts = , ; }; frame@17c23000 { reg = <0x17c23000 0x1000>; frame-number = <1>; interrupts = ; status = "disabled"; }; frame@17c25000 { reg = <0x17c25000 0x1000>; frame-number = <2>; interrupts = ; status = "disabled"; }; frame@17c27000 { reg = <0x17c26000 0x1000>; frame-number = <3>; interrupts = ; status = "disabled"; }; frame@17c29000 { reg = <0x17c29000 0x1000>; frame-number = <4>; interrupts = ; status = "disabled"; }; frame@17c2b000 { reg = <0x17c2b000 0x1000>; frame-number = <5>; interrupts = ; status = "disabled"; }; frame@17c2d000 { reg = <0x17c2d000 0x1000>; frame-number = <6>; interrupts = ; status = "disabled"; }; }; apps_rsc: rsc@18200000 { compatible = "qcom,rpmh-rsc"; reg = <0x0 0x18200000 0x0 0x10000>, <0x0 0x18210000 0x0 0x10000>, <0x0 0x18220000 0x0 0x10000>; reg-names = "drv-0", "drv-1", "drv-2"; interrupts = , , ; qcom,tcs-offset = <0xd00>; qcom,drv-id = <2>; qcom,tcs-config = , , , ; label = "apps_rsc"; power-domains = <&CLUSTER_PD>; apps_bcm_voter: bcm-voter { compatible = "qcom,bcm-voter"; }; rpmhcc: clock-controller { compatible = "qcom,sc8180x-rpmh-clk"; #clock-cells = <1>; clock-names = "xo"; clocks = <&xo_board_clk>; }; rpmhpd: power-controller { compatible = "qcom,sc8180x-rpmhpd"; #power-domain-cells = <1>; operating-points-v2 = <&rpmhpd_opp_table>; rpmhpd_opp_table: opp-table { compatible = "operating-points-v2"; rpmhpd_opp_ret: opp1 { opp-level = ; }; rpmhpd_opp_min_svs: opp2 { opp-level = ; }; rpmhpd_opp_low_svs: opp3 { opp-level = ; }; rpmhpd_opp_svs: opp4 { opp-level = ; }; rpmhpd_opp_svs_l1: opp5 { opp-level = ; }; rpmhpd_opp_nom: opp6 { opp-level = ; }; rpmhpd_opp_nom_l1: opp7 { opp-level = ; }; rpmhpd_opp_nom_l2: opp8 { opp-level = ; }; rpmhpd_opp_turbo: opp9 { opp-level = ; }; rpmhpd_opp_turbo_l1: opp10 { opp-level = ; }; }; }; }; osm_l3: interconnect@18321000 { compatible = "qcom,sc8180x-osm-l3", "qcom,osm-l3"; reg = <0 0x18321000 0 0x1400>; clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>; clock-names = "xo", "alternate"; #interconnect-cells = <1>; }; lmh@18350800 { compatible = "qcom,sc8180x-lmh"; reg = <0 0x18350800 0 0x400>; interrupts = ; cpus = <&CPU4>; qcom,lmh-temp-arm-millicelsius = <65000>; qcom,lmh-temp-low-millicelsius = <94500>; qcom,lmh-temp-high-millicelsius = <95000>; interrupt-controller; #interrupt-cells = <1>; }; lmh@18358800 { compatible = "qcom,sc8180x-lmh"; reg = <0 0x18358800 0 0x400>; interrupts = ; cpus = <&CPU0>; qcom,lmh-temp-arm-millicelsius = <65000>; qcom,lmh-temp-low-millicelsius = <94500>; qcom,lmh-temp-high-millicelsius = <95000>; interrupt-controller; #interrupt-cells = <1>; }; cpufreq_hw: cpufreq@18323000 { compatible = "qcom,cpufreq-hw"; reg = <0 0x18323000 0 0x1400>, <0 0x18325800 0 0x1400>; reg-names = "freq-domain0", "freq-domain1"; clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>; clock-names = "xo", "alternate"; #freq-domain-cells = <1>; #clock-cells = <1>; }; wifi: wifi@18800000 { compatible = "qcom,wcn3990-wifi"; reg = <0 0x18800000 0 0x800000>; reg-names = "membase"; clock-names = "cxo_ref_clk_pin"; clocks = <&rpmhcc RPMH_RF_CLK2>; interrupts = , , , , , , , , , , , ; iommus = <&apps_smmu 0x0640 0x1>; qcom,msa-fixed-perm; status = "disabled"; }; }; thermal-zones { cpu0-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens0 1>; trips { cpu-crit { temperature = <110000>; hysteresis = <1000>; type = "critical"; }; }; }; cpu1-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens0 2>; trips { cpu-crit { temperature = <110000>; hysteresis = <1000>; type = "critical"; }; }; }; cpu2-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens0 3>; trips { cpu-crit { temperature = <110000>; hysteresis = <1000>; type = "critical"; }; }; }; cpu3-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens0 4>; trips { cpu-crit { temperature = <110000>; hysteresis = <1000>; type = "critical"; }; }; }; cpu4-top-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens0 7>; trips { cpu-crit { temperature = <110000>; hysteresis = <1000>; type = "critical"; }; }; }; cpu5-top-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens0 8>; trips { cpu-crit { temperature = <110000>; hysteresis = <1000>; type = "critical"; }; }; }; cpu6-top-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens0 9>; trips { cpu-crit { temperature = <110000>; hysteresis = <1000>; type = "critical"; }; }; }; cpu7-top-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens0 10>; trips { cpu-crit { temperature = <110000>; hysteresis = <1000>; type = "critical"; }; }; }; cpu4-bottom-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens0 11>; trips { cpu-crit { temperature = <110000>; hysteresis = <1000>; type = "critical"; }; }; }; cpu5-bottom-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens0 12>; trips { cpu-crit { temperature = <110000>; hysteresis = <1000>; type = "critical"; }; }; }; cpu6-bottom-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens0 13>; trips { cpu-crit { temperature = <110000>; hysteresis = <1000>; type = "critical"; }; }; }; cpu7-bottom-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens0 14>; trips { cpu-crit { temperature = <110000>; hysteresis = <1000>; type = "critical"; }; }; }; aoss0-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens0 0>; trips { trip-point0 { temperature = <90000>; hysteresis = <2000>; type = "hot"; }; }; }; cluster0-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens0 5>; trips { cluster-crit { temperature = <110000>; hysteresis = <2000>; type = "critical"; }; }; }; cluster1-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens0 6>; trips { cluster-crit { temperature = <110000>; hysteresis = <2000>; type = "critical"; }; }; }; gpu-top-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens0 15>; cooling-maps { map0 { trip = <&gpu_top_alert0>; cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; }; }; trips { gpu_top_alert0: trip-point0 { temperature = <90000>; hysteresis = <2000>; type = "hot"; }; }; }; aoss1-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens1 0>; trips { trip-point0 { temperature = <90000>; hysteresis = <2000>; type = "hot"; }; }; }; wlan-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens1 1>; trips { trip-point0 { temperature = <90000>; hysteresis = <2000>; type = "hot"; }; }; }; video-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens1 2>; trips { trip-point0 { temperature = <90000>; hysteresis = <2000>; type = "hot"; }; }; }; mem-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens1 3>; trips { trip-point0 { temperature = <90000>; hysteresis = <2000>; type = "hot"; }; }; }; q6-hvx-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens1 4>; trips { trip-point0 { temperature = <90000>; hysteresis = <2000>; type = "hot"; }; }; }; camera-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens1 5>; trips { trip-point0 { temperature = <90000>; hysteresis = <2000>; type = "hot"; }; }; }; compute-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens1 6>; trips { trip-point0 { temperature = <90000>; hysteresis = <2000>; type = "hot"; }; }; }; mdm-dsp-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens1 7>; trips { trip-point0 { temperature = <90000>; hysteresis = <2000>; type = "hot"; }; }; }; npu-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens1 8>; trips { trip-point0 { temperature = <90000>; hysteresis = <2000>; type = "hot"; }; }; }; gpu-bottom-thermal { polling-delay-passive = <250>; polling-delay = <1000>; thermal-sensors = <&tsens1 11>; cooling-maps { map0 { trip = <&gpu_bottom_alert0>; cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; }; }; trips { gpu_bottom_alert0: trip-point0 { temperature = <90000>; hysteresis = <2000>; type = "hot"; }; }; }; }; timer { compatible = "arm,armv8-timer"; interrupts = , , , ; }; };