From: Thomas Gleixner Date: Thu, 14 Sep 2023 20:43:29 +0206 Subject: [PATCH 012/134] serial: 8250_omap: Use port lock wrappers Origin: https://www.kernel.org/pub/linux/kernel/projects/rt/6.6/older/patches-6.6.7-rt18.tar.xz When a serial port is used for kernel console output, then all modifications to the UART registers which are done from other contexts, e.g. getty, termios, are interference points for the kernel console. So far this has been ignored and the printk output is based on the principle of hope. The rework of the console infrastructure which aims to support threaded and atomic consoles, requires to mark sections which modify the UART registers as unsafe. This allows the atomic write function to make informed decisions and eventually to restore operational state. It also allows to prevent the regular UART code from modifying UART registers while printk output is in progress. All modifications of UART registers are guarded by the UART port lock, which provides an obvious synchronization point with the console infrastructure. To avoid adding this functionality to all UART drivers, wrap the spin_[un]lock*() invocations for uart_port::lock into helper functions which just contain the spin_[un]lock*() invocations for now. In a subsequent step these helpers will gain the console synchronization mechanisms. Converted with coccinelle. No functional change. Signed-off-by: Thomas Gleixner Signed-off-by: John Ogness Link: https://lore.kernel.org/r/20230914183831.587273-13-john.ogness@linutronix.de Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sebastian Andrzej Siewior --- drivers/tty/serial/8250/8250_omap.c | 52 ++++++++++++++++++------------------ 1 file changed, 26 insertions(+), 26 deletions(-) --- a/drivers/tty/serial/8250/8250_omap.c +++ b/drivers/tty/serial/8250/8250_omap.c @@ -401,7 +401,7 @@ static void omap_8250_set_termios(struct * interrupts disabled. */ pm_runtime_get_sync(port->dev); - spin_lock_irq(&port->lock); + uart_port_lock_irq(port); /* * Update the per-port timeout. @@ -504,7 +504,7 @@ static void omap_8250_set_termios(struct } omap8250_restore_regs(up); - spin_unlock_irq(&up->port.lock); + uart_port_unlock_irq(&up->port); pm_runtime_mark_last_busy(port->dev); pm_runtime_put_autosuspend(port->dev); @@ -529,7 +529,7 @@ static void omap_8250_pm(struct uart_por pm_runtime_get_sync(port->dev); /* Synchronize UART_IER access against the console. */ - spin_lock_irq(&port->lock); + uart_port_lock_irq(port); serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); efr = serial_in(up, UART_EFR); @@ -541,7 +541,7 @@ static void omap_8250_pm(struct uart_por serial_out(up, UART_EFR, efr); serial_out(up, UART_LCR, 0); - spin_unlock_irq(&port->lock); + uart_port_unlock_irq(port); pm_runtime_mark_last_busy(port->dev); pm_runtime_put_autosuspend(port->dev); @@ -660,7 +660,7 @@ static irqreturn_t omap8250_irq(int irq, unsigned long delay; /* Synchronize UART_IER access against the console. */ - spin_lock(&port->lock); + uart_port_lock(port); up->ier = port->serial_in(port, UART_IER); if (up->ier & (UART_IER_RLSI | UART_IER_RDI)) { port->ops->stop_rx(port); @@ -670,7 +670,7 @@ static irqreturn_t omap8250_irq(int irq, */ cancel_delayed_work(&up->overrun_backoff); } - spin_unlock(&port->lock); + uart_port_unlock(port); delay = msecs_to_jiffies(up->overrun_backoff_time_ms); schedule_delayed_work(&up->overrun_backoff, delay); @@ -717,10 +717,10 @@ static int omap_8250_startup(struct uart } /* Synchronize UART_IER access against the console. */ - spin_lock_irq(&port->lock); + uart_port_lock_irq(port); up->ier = UART_IER_RLSI | UART_IER_RDI; serial_out(up, UART_IER, up->ier); - spin_unlock_irq(&port->lock); + uart_port_unlock_irq(port); #ifdef CONFIG_PM up->capabilities |= UART_CAP_RPM; @@ -733,9 +733,9 @@ static int omap_8250_startup(struct uart serial_out(up, UART_OMAP_WER, priv->wer); if (up->dma && !(priv->habit & UART_HAS_EFR2)) { - spin_lock_irq(&port->lock); + uart_port_lock_irq(port); up->dma->rx_dma(up); - spin_unlock_irq(&port->lock); + uart_port_unlock_irq(port); } enable_irq(up->port.irq); @@ -761,10 +761,10 @@ static void omap_8250_shutdown(struct ua serial_out(up, UART_OMAP_EFR2, 0x0); /* Synchronize UART_IER access against the console. */ - spin_lock_irq(&port->lock); + uart_port_lock_irq(port); up->ier = 0; serial_out(up, UART_IER, 0); - spin_unlock_irq(&port->lock); + uart_port_unlock_irq(port); disable_irq_nosync(up->port.irq); dev_pm_clear_wake_irq(port->dev); @@ -789,10 +789,10 @@ static void omap_8250_throttle(struct ua pm_runtime_get_sync(port->dev); - spin_lock_irqsave(&port->lock, flags); + uart_port_lock_irqsave(port, &flags); port->ops->stop_rx(port); priv->throttled = true; - spin_unlock_irqrestore(&port->lock, flags); + uart_port_unlock_irqrestore(port, flags); pm_runtime_mark_last_busy(port->dev); pm_runtime_put_autosuspend(port->dev); @@ -807,14 +807,14 @@ static void omap_8250_unthrottle(struct pm_runtime_get_sync(port->dev); /* Synchronize UART_IER access against the console. */ - spin_lock_irqsave(&port->lock, flags); + uart_port_lock_irqsave(port, &flags); priv->throttled = false; if (up->dma) up->dma->rx_dma(up); up->ier |= UART_IER_RLSI | UART_IER_RDI; port->read_status_mask |= UART_LSR_DR; serial_out(up, UART_IER, up->ier); - spin_unlock_irqrestore(&port->lock, flags); + uart_port_unlock_irqrestore(port, flags); pm_runtime_mark_last_busy(port->dev); pm_runtime_put_autosuspend(port->dev); @@ -958,7 +958,7 @@ static void __dma_rx_complete(void *para unsigned long flags; /* Synchronize UART_IER access against the console. */ - spin_lock_irqsave(&p->port.lock, flags); + uart_port_lock_irqsave(&p->port, &flags); /* * If the tx status is not DMA_COMPLETE, then this is a delayed @@ -967,7 +967,7 @@ static void __dma_rx_complete(void *para */ if (dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state) != DMA_COMPLETE) { - spin_unlock_irqrestore(&p->port.lock, flags); + uart_port_unlock_irqrestore(&p->port, flags); return; } __dma_rx_do_complete(p); @@ -978,7 +978,7 @@ static void __dma_rx_complete(void *para omap_8250_rx_dma(p); } - spin_unlock_irqrestore(&p->port.lock, flags); + uart_port_unlock_irqrestore(&p->port, flags); } static void omap_8250_rx_dma_flush(struct uart_8250_port *p) @@ -1083,7 +1083,7 @@ static void omap_8250_dma_tx_complete(vo dma_sync_single_for_cpu(dma->txchan->device->dev, dma->tx_addr, UART_XMIT_SIZE, DMA_TO_DEVICE); - spin_lock_irqsave(&p->port.lock, flags); + uart_port_lock_irqsave(&p->port, &flags); dma->tx_running = 0; @@ -1112,7 +1112,7 @@ static void omap_8250_dma_tx_complete(vo serial8250_set_THRI(p); } - spin_unlock_irqrestore(&p->port.lock, flags); + uart_port_unlock_irqrestore(&p->port, flags); } static int omap_8250_tx_dma(struct uart_8250_port *p) @@ -1278,7 +1278,7 @@ static int omap_8250_dma_handle_irq(stru return IRQ_HANDLED; } - spin_lock(&port->lock); + uart_port_lock(port); status = serial_port_in(port, UART_LSR); @@ -1756,15 +1756,15 @@ static int omap8250_runtime_resume(struc up = serial8250_get_port(priv->line); if (up && omap8250_lost_context(up)) { - spin_lock_irq(&up->port.lock); + uart_port_lock_irq(&up->port); omap8250_restore_regs(up); - spin_unlock_irq(&up->port.lock); + uart_port_unlock_irq(&up->port); } if (up && up->dma && up->dma->rxchan && !(priv->habit & UART_HAS_EFR2)) { - spin_lock_irq(&up->port.lock); + uart_port_lock_irq(&up->port); omap_8250_rx_dma(up); - spin_unlock_irq(&up->port.lock); + uart_port_unlock_irq(&up->port); } priv->latency = priv->calc_latency;