/* SPDX-License-Identifier: GPL-2.0-or-later */ /* atlx_hw.h -- common hardware definitions for Attansic network drivers * * Copyright(c) 2005 - 2006 Attansic Corporation. All rights reserved. * Copyright(c) 2006 - 2007 Chris Snook <csnook@redhat.com> * Copyright(c) 2006 - 2008 Jay Cliburn <jcliburn@gmail.com> * Copyright(c) 2007 Atheros Corporation. All rights reserved. * * Derived from Intel e1000 driver * Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved. */ #ifndef ATLX_H #define ATLX_H #include <linux/module.h> #include <linux/types.h> #define ATLX_ERR_PHY 2 #define ATLX_ERR_PHY_SPEED 7 #define ATLX_ERR_PHY_RES 8 #define SPEED_0 0xffff #define SPEED_10 10 #define SPEED_100 100 #define SPEED_1000 1000 #define HALF_DUPLEX 1 #define FULL_DUPLEX 2 #define MEDIA_TYPE_AUTO_SENSOR 0 /* register definitions */ #define REG_PM_CTRLSTAT 0x44 #define REG_PCIE_CAP_LIST 0x58 #define REG_VPD_CAP 0x6C #define VPD_CAP_ID_MASK 0xFF #define VPD_CAP_ID_SHIFT 0 #define VPD_CAP_NEXT_PTR_MASK 0xFF #define VPD_CAP_NEXT_PTR_SHIFT 8 #define VPD_CAP_VPD_ADDR_MASK 0x7FFF #define VPD_CAP_VPD_ADDR_SHIFT 16 #define VPD_CAP_VPD_FLAG 0x80000000 #define REG_VPD_DATA 0x70 #define REG_SPI_FLASH_CTRL 0x200 #define SPI_FLASH_CTRL_STS_NON_RDY 0x1 #define SPI_FLASH_CTRL_STS_WEN 0x2 #define SPI_FLASH_CTRL_STS_WPEN 0x80 #define SPI_FLASH_CTRL_DEV_STS_MASK 0xFF #define SPI_FLASH_CTRL_DEV_STS_SHIFT 0 #define SPI_FLASH_CTRL_INS_MASK 0x7 #define SPI_FLASH_CTRL_INS_SHIFT 8 #define SPI_FLASH_CTRL_START 0x800 #define SPI_FLASH_CTRL_EN_VPD 0x2000 #define SPI_FLASH_CTRL_LDSTART 0x8000 #define SPI_FLASH_CTRL_CS_HI_MASK 0x3 #define SPI_FLASH_CTRL_CS_HI_SHIFT 16 #define SPI_FLASH_CTRL_CS_HOLD_MASK 0x3 #define SPI_FLASH_CTRL_CS_HOLD_SHIFT 18 #define SPI_FLASH_CTRL_CLK_LO_MASK 0x3 #define SPI_FLASH_CTRL_CLK_LO_SHIFT 20 #define SPI_FLASH_CTRL_CLK_HI_MASK 0x3 #define SPI_FLASH_CTRL_CLK_HI_SHIFT 22 #define SPI_FLASH_CTRL_CS_SETUP_MASK 0x3 #define SPI_FLASH_CTRL_CS_SETUP_SHIFT 24 #define SPI_FLASH_CTRL_EROM_PGSZ_MASK 0x3 #define SPI_FLASH_CTRL_EROM_PGSZ_SHIFT 26 #define SPI_FLASH_CTRL_WAIT_READY 0x10000000 #define REG_SPI_ADDR 0x204 #define REG_SPI_DATA 0x208 #define REG_SPI_FLASH_CONFIG 0x20C #define SPI_FLASH_CONFIG_LD_ADDR_MASK 0xFFFFFF #define SPI_FLASH_CONFIG_LD_ADDR_SHIFT 0 #define SPI_FLASH_CONFIG_VPD_ADDR_MASK 0x3 #define SPI_FLASH_CONFIG_VPD_ADDR_SHIFT 24 #define SPI_FLASH_CONFIG_LD_EXIST 0x4000000 #define REG_SPI_FLASH_OP_PROGRAM 0x210 #define REG_SPI_FLASH_OP_SC_ERASE 0x211 #define REG_SPI_FLASH_OP_CHIP_ERASE 0x212 #define REG_SPI_FLASH_OP_RDID 0x213 #define REG_SPI_FLASH_OP_WREN 0x214 #define REG_SPI_FLASH_OP_RDSR 0x215 #define REG_SPI_FLASH_OP_WRSR 0x216 #define REG_SPI_FLASH_OP_READ 0x217 #define REG_TWSI_CTRL 0x218 #define TWSI_CTRL_LD_OFFSET_MASK 0xFF #define TWSI_CTRL_LD_OFFSET_SHIFT 0 #define TWSI_CTRL_LD_SLV_ADDR_MASK 0x7 #define TWSI_CTRL_LD_SLV_ADDR_SHIFT 8 #define TWSI_CTRL_SW_LDSTART 0x800 #define TWSI_CTRL_HW_LDSTART 0x1000 #define TWSI_CTRL_SMB_SLV_ADDR_MASK 0x7F #define TWSI_CTRL_SMB_SLV_ADDR_SHIFT 15 #define TWSI_CTRL_LD_EXIST 0x400000 #define TWSI_CTRL_READ_FREQ_SEL_MASK 0x3 #define TWSI_CTRL_READ_FREQ_SEL_SHIFT 23 #define TWSI_CTRL_FREQ_SEL_100K 0 #define TWSI_CTRL_FREQ_SEL_200K 1 #define TWSI_CTRL_FREQ_SEL_300K 2 #define TWSI_CTRL_FREQ_SEL_400K 3 #define TWSI_CTRL_SMB_SLV_ADDR /* FIXME: define or remove */ #define TWSI_CTRL_WRITE_FREQ_SEL_MASK 0x3 #define TWSI_CTRL_WRITE_FREQ_SEL_SHIFT 24 #define REG_PCIE_DEV_MISC_CTRL 0x21C #define PCIE_DEV_MISC_CTRL_EXT_PIPE 0x2 #define PCIE_DEV_MISC_CTRL_RETRY_BUFDIS 0x1 #define PCIE_DEV_MISC_CTRL_SPIROM_EXIST 0x4 #define PCIE_DEV_MISC_CTRL_SERDES_ENDIAN 0x8 #define PCIE_DEV_MISC_CTRL_SERDES_SEL_DIN 0x10 #define REG_PCIE_PHYMISC 0x1000 #define PCIE_PHYMISC_FORCE_RCV_DET 0x4 #define REG_PCIE_DLL_TX_CTRL1 0x1104 #define PCIE_DLL_TX_CTRL1_SEL_NOR_CLK 0x400 #define PCIE_DLL_TX_CTRL1_DEF 0x568 #define REG_LTSSM_TEST_MODE 0x12FC #define LTSSM_TEST_MODE_DEF 0x6500 /* Master Control Register */ #define REG_MASTER_CTRL 0x1400 #define MASTER_CTRL_SOFT_RST 0x1 #define MASTER_CTRL_MTIMER_EN 0x2 #define MASTER_CTRL_ITIMER_EN 0x4 #define MASTER_CTRL_MANUAL_INT 0x8 #define MASTER_CTRL_REV_NUM_SHIFT 16 #define MASTER_CTRL_REV_NUM_MASK 0xFF #define MASTER_CTRL_DEV_ID_SHIFT 24 #define MASTER_CTRL_DEV_ID_MASK 0xFF /* Timer Initial Value Register */ #define REG_MANUAL_TIMER_INIT 0x1404 /* IRQ Moderator Timer Initial Value Register */ #define REG_IRQ_MODU_TIMER_INIT 0x1408 #define REG_PHY_ENABLE 0x140C /* IRQ Anti-Lost Timer Initial Value Register */ #define REG_CMBDISDMA_TIMER 0x140E /* Block IDLE Status Register */ #define REG_IDLE_STATUS 0x1410 /* MDIO Control Register */ #define REG_MDIO_CTRL 0x1414 #define MDIO_DATA_MASK 0xFFFF #define MDIO_DATA_SHIFT 0 #define MDIO_REG_ADDR_MASK 0x1F #define MDIO_REG_ADDR_SHIFT 16 #define MDIO_RW 0x200000 #define MDIO_SUP_PREAMBLE 0x400000 #define MDIO_START 0x800000 #define MDIO_CLK_SEL_SHIFT 24 #define MDIO_CLK_25_4 0 #define MDIO_CLK_25_6 2 #define MDIO_CLK_25_8 3 #define MDIO_CLK_25_10 4 #define MDIO_CLK_25_14 5 #define MDIO_CLK_25_20 6 #define MDIO_CLK_25_28 7 #define MDIO_BUSY 0x8000000 /* MII PHY Status Register */ #define REG_PHY_STATUS 0x1418 /* BIST Control and Status Register0 (for the Packet Memory) */ #define REG_BIST0_CTRL 0x141C #define BIST0_NOW 0x1 #define BIST0_SRAM_FAIL 0x2 #define BIST0_FUSE_FLAG 0x4 #define REG_BIST1_CTRL 0x1420 #define BIST1_NOW 0x1 #define BIST1_SRAM_FAIL 0x2 #define BIST1_FUSE_FLAG 0x4 /* SerDes Lock Detect Control and Status Register */ #define REG_SERDES_LOCK 0x1424 #define SERDES_LOCK_DETECT 1 #define SERDES_LOCK_DETECT_EN 2 /* MAC Control Register */ #define REG_MAC_CTRL 0x1480 #define MAC_CTRL_TX_EN 1 #define MAC_CTRL_RX_EN 2 #define MAC_CTRL_TX_FLOW 4 #define MAC_CTRL_RX_FLOW 8 #define MAC_CTRL_LOOPBACK 0x10 #define MAC_CTRL_DUPLX 0x20 #define MAC_CTRL_ADD_CRC 0x40 #define MAC_CTRL_PAD 0x80 #define MAC_CTRL_LENCHK 0x100 #define MAC_CTRL_HUGE_EN 0x200 #define MAC_CTRL_PRMLEN_SHIFT 10 #define MAC_CTRL_PRMLEN_MASK 0xF #define MAC_CTRL_RMV_VLAN 0x4000 #define MAC_CTRL_PROMIS_EN 0x8000 #define MAC_CTRL_MC_ALL_EN 0x2000000 #define MAC_CTRL_BC_EN 0x4000000 /* MAC IPG/IFG Control Register */ #define REG_MAC_IPG_IFG 0x1484 #define MAC_IPG_IFG_IPGT_SHIFT 0 #define MAC_IPG_IFG_IPGT_MASK 0x7F #define MAC_IPG_IFG_MIFG_SHIFT 8 #define MAC_IPG_IFG_MIFG_MASK 0xFF #define MAC_IPG_IFG_IPGR1_SHIFT 16 #define MAC_IPG_IFG_IPGR1_MASK 0x7F #define MAC_IPG_IFG_IPGR2_SHIFT 24 #define MAC_IPG_IFG_IPGR2_MASK 0x7F /* MAC STATION ADDRESS */ #define REG_MAC_STA_ADDR 0x1488 /* Hash table for multicast address */ #define REG_RX_HASH_TABLE 0x1490 /* MAC Half-Duplex Control Register */ #define REG_MAC_HALF_DUPLX_CTRL 0x1498 #define MAC_HALF_DUPLX_CTRL_LCOL_SHIFT 0 #define MAC_HALF_DUPLX_CTRL_LCOL_MASK 0x3FF #define MAC_HALF_DUPLX_CTRL_RETRY_SHIFT 12 #define MAC_HALF_DUPLX_CTRL_RETRY_MASK 0xF #define MAC_HALF_DUPLX_CTRL_EXC_DEF_EN 0x10000 #define MAC_HALF_DUPLX_CTRL_NO_BACK_C 0x20000 #define MAC_HALF_DUPLX_CTRL_NO_BACK_P 0x40000 #define MAC_HALF_DUPLX_CTRL_ABEBE 0x80000 #define MAC_HALF_DUPLX_CTRL_ABEBT_SHIFT 20 #define MAC_HALF_DUPLX_CTRL_ABEBT_MASK 0xF #define MAC_HALF_DUPLX_CTRL_JAMIPG_SHIFT 24 #define MAC_HALF_DUPLX_CTRL_JAMIPG_MASK 0xF /* Maximum Frame Length Control Register */ #define REG_MTU 0x149C /* Wake-On-Lan control register */ #define REG_WOL_CTRL 0x14A0 #define WOL_PATTERN_EN 0x1 #define WOL_PATTERN_PME_EN 0x2 #define WOL_MAGIC_EN 0x4 #define WOL_MAGIC_PME_EN 0x8 #define WOL_LINK_CHG_EN 0x10 #define WOL_LINK_CHG_PME_EN 0x20 #define WOL_PATTERN_ST 0x100 #define WOL_MAGIC_ST 0x200 #define WOL_LINKCHG_ST 0x400 #define WOL_PT0_EN 0x10000 #define WOL_PT1_EN 0x20000 #define WOL_PT2_EN 0x40000 #define WOL_PT3_EN 0x80000 #define WOL_PT4_EN 0x100000 #define WOL_PT0_MATCH 0x1000000 #define WOL_PT1_MATCH 0x2000000 #define WOL_PT2_MATCH 0x4000000 #define WOL_PT3_MATCH 0x8000000 #define WOL_PT4_MATCH 0x10000000 /* Internal SRAM Partition Register, high 32 bits */ #define REG_SRAM_RFD_ADDR 0x1500 /* Descriptor Control register, high 32 bits */ #define REG_DESC_BASE_ADDR_HI 0x1540 /* Interrupt Status Register */ #define REG_ISR 0x1600 #define ISR_UR_DETECTED 0x1000000 #define ISR_FERR_DETECTED 0x2000000 #define ISR_NFERR_DETECTED 0x4000000 #define ISR_CERR_DETECTED 0x8000000 #define ISR_PHY_LINKDOWN 0x10000000 #define ISR_DIS_INT 0x80000000 /* Interrupt Mask Register */ #define REG_IMR 0x1604 #define REG_RFD_RRD_IDX 0x1800 #define REG_TPD_IDX 0x1804 /* MII definitions */ /* PHY Common Register */ #define MII_ATLX_CR 0x09 #define MII_ATLX_SR 0x0A #define MII_ATLX_ESR 0x0F #define MII_ATLX_PSCR 0x10 #define MII_ATLX_PSSR 0x11 /* PHY Control Register */ #define MII_CR_SPEED_SELECT_MSB 0x0040 /* bits 6,13: 10=1000, 01=100, * 00=10 */ #define MII_CR_COLL_TEST_ENABLE 0x0080 /* Collision test enable */ #define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */ #define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */ #define MII_CR_ISOLATE 0x0400 /* Isolate PHY from MII */ #define MII_CR_POWER_DOWN 0x0800 /* Power down */ #define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */ #define MII_CR_SPEED_SELECT_LSB 0x2000 /* bits 6,13: 10=1000, 01=100, * 00=10 */ #define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */ #define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */ #define MII_CR_SPEED_MASK 0x2040 #define MII_CR_SPEED_1000 0x0040 #define MII_CR_SPEED_100 0x2000 #define MII_CR_SPEED_10 0x0000 /* PHY Status Register */ #define MII_SR_EXTENDED_CAPS 0x0001 /* Ext register capabilities */ #define MII_SR_JABBER_DETECT 0x0002 /* Jabber Detected */ #define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */ #define MII_SR_AUTONEG_CAPS 0x0008 /* Auto Neg Capable */ #define MII_SR_REMOTE_FAULT 0x0010 /* Remote Fault Detect */ #define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */ #define MII_SR_PREAMBLE_SUPPRESS 0x0040 /* Preamble may be suppressed */ #define MII_SR_EXTENDED_STATUS 0x0100 /* Ext stat info in Reg 0x0F */ #define MII_SR_100T2_HD_CAPS 0x0200 /* 100T2 Half Duplex Capable */ #define MII_SR_100T2_FD_CAPS 0x0400 /* 100T2 Full Duplex Capable */ #define MII_SR_10T_HD_CAPS 0x0800 /* 10T Half Duplex Capable */ #define MII_SR_10T_FD_CAPS 0x1000 /* 10T Full Duplex Capable */ #define MII_SR_100X_HD_CAPS 0x2000 /* 100X Half Duplex Capable */ #define MII_SR_100X_FD_CAPS 0x4000 /* 100X Full Duplex Capable */ #define MII_SR_100T4_CAPS 0x8000 /* 100T4 Capable */ /* Link partner ability register */ #define MII_LPA_SLCT 0x001f /* Same as advertise selector */ #define MII_LPA_10HALF 0x0020 /* Can do 10mbps half-duplex */ #define MII_LPA_10FULL 0x0040 /* Can do 10mbps full-duplex */ #define MII_LPA_100HALF 0x0080 /* Can do 100mbps half-duplex */ #define MII_LPA_100FULL 0x0100 /* Can do 100mbps full-duplex */ #define MII_LPA_100BASE4 0x0200 /* 100BASE-T4 */ #define MII_LPA_PAUSE 0x0400 /* PAUSE */ #define MII_LPA_ASYPAUSE 0x0800 /* Asymmetrical PAUSE */ #define MII_LPA_RFAULT 0x2000 /* Link partner faulted */ #define MII_LPA_LPACK 0x4000 /* Link partner acked us */ #define MII_LPA_NPAGE 0x8000 /* Next page bit */ /* Autoneg Advertisement Register */ #define MII_AR_SELECTOR_FIELD 0x0001 /* IEEE 802.3 CSMA/CD */ #define MII_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */ #define MII_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */ #define MII_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */ #define MII_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */ #define MII_AR_100T4_CAPS 0x0200 /* 100T4 Capable */ #define MII_AR_PAUSE 0x0400 /* Pause operation desired */ #define MII_AR_ASM_DIR 0x0800 /* Asymmetric Pause Dir bit */ #define MII_AR_REMOTE_FAULT 0x2000 /* Remote Fault detected */ #define MII_AR_NEXT_PAGE 0x8000 /* Next Page ability support */ #define MII_AR_SPEED_MASK 0x01E0 #define MII_AR_DEFAULT_CAP_MASK 0x0DE0 /* 1000BASE-T Control Register */ #define MII_ATLX_CR_1000T_HD_CAPS 0x0100 /* Adv 1000T HD cap */ #define MII_ATLX_CR_1000T_FD_CAPS 0x0200 /* Adv 1000T FD cap */ #define MII_ATLX_CR_1000T_REPEATER_DTE 0x0400 /* 1=Repeater/switch device, * 0=DTE device */ #define MII_ATLX_CR_1000T_MS_VALUE 0x0800 /* 1=Config PHY as Master, * 0=Configure PHY as Slave */ #define MII_ATLX_CR_1000T_MS_ENABLE 0x1000 /* 1=Man Master/Slave config, * 0=Auto Master/Slave config */ #define MII_ATLX_CR_1000T_TEST_MODE_NORMAL 0x0000 /* Normal Operation */ #define MII_ATLX_CR_1000T_TEST_MODE_1 0x2000 /* Transmit Waveform test */ #define MII_ATLX_CR_1000T_TEST_MODE_2 0x4000 /* Master Xmit Jitter test */ #define MII_ATLX_CR_1000T_TEST_MODE_3 0x6000 /* Slave Xmit Jitter test */ #define MII_ATLX_CR_1000T_TEST_MODE_4 0x8000 /* Xmitter Distortion test */ #define MII_ATLX_CR_1000T_SPEED_MASK 0x0300 #define MII_ATLX_CR_1000T_DEFAULT_CAP_MASK 0x0300 /* 1000BASE-T Status Register */ #define MII_ATLX_SR_1000T_LP_HD_CAPS 0x0400 /* LP is 1000T HD capable */ #define MII_ATLX_SR_1000T_LP_FD_CAPS 0x0800 /* LP is 1000T FD capable */ #define MII_ATLX_SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */ #define MII_ATLX_SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */ #define MII_ATLX_SR_1000T_MS_CONFIG_RES 0x4000 /* 1=Local TX is Master * 0=Slave */ #define MII_ATLX_SR_1000T_MS_CONFIG_FAULT 0x8000 /* Master/Slave config * fault */ #define MII_ATLX_SR_1000T_REMOTE_RX_STATUS_SHIFT 12 #define MII_ATLX_SR_1000T_LOCAL_RX_STATUS_SHIFT 13 /* Extended Status Register */ #define MII_ATLX_ESR_1000T_HD_CAPS 0x1000 /* 1000T HD capable */ #define MII_ATLX_ESR_1000T_FD_CAPS 0x2000 /* 1000T FD capable */ #define MII_ATLX_ESR_1000X_HD_CAPS 0x4000 /* 1000X HD capable */ #define MII_ATLX_ESR_1000X_FD_CAPS 0x8000 /* 1000X FD capable */ /* ATLX PHY Specific Control Register */ #define MII_ATLX_PSCR_JABBER_DISABLE 0x0001 /* 1=Jabber Func disabled */ #define MII_ATLX_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enbld */ #define MII_ATLX_PSCR_SQE_TEST 0x0004 /* 1=SQE Test enabled */ #define MII_ATLX_PSCR_MAC_POWERDOWN 0x0008 #define MII_ATLX_PSCR_CLK125_DISABLE 0x0010 /* 1=CLK125 low * 0=CLK125 toggling */ #define MII_ATLX_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5, * Manual MDI configuration */ #define MII_ATLX_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */ #define MII_ATLX_PSCR_AUTO_X_1000T 0x0040 /* 1000BASE-T: Auto crossover * 100BASE-TX/10BASE-T: MDI * Mode */ #define MII_ATLX_PSCR_AUTO_X_MODE 0x0060 /* Auto crossover enabled * all speeds. */ #define MII_ATLX_PSCR_10BT_EXT_DIST_ENABLE 0x0080 /* 1=Enable Extended * 10BASE-T distance * (Lower 10BASE-T RX * Threshold) * 0=Normal 10BASE-T RX * Threshold */ #define MII_ATLX_PSCR_MII_5BIT_ENABLE 0x0100 /* 1=5-Bit interface in * 100BASE-TX * 0=MII interface in * 100BASE-TX */ #define MII_ATLX_PSCR_SCRAMBLER_DISABLE 0x0200 /* 1=Scrambler dsbl */ #define MII_ATLX_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force link good */ #define MII_ATLX_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */ #define MII_ATLX_PSCR_POLARITY_REVERSAL_SHIFT 1 #define MII_ATLX_PSCR_AUTO_X_MODE_SHIFT 5 #define MII_ATLX_PSCR_10BT_EXT_DIST_ENABLE_SHIFT 7 /* ATLX PHY Specific Status Register */ #define MII_ATLX_PSSR_SPD_DPLX_RESOLVED 0x0800 /* 1=Speed & Duplex resolved */ #define MII_ATLX_PSSR_DPLX 0x2000 /* 1=Duplex 0=Half Duplex */ #define MII_ATLX_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */ #define MII_ATLX_PSSR_10MBS 0x0000 /* 00=10Mbs */ #define MII_ATLX_PSSR_100MBS 0x4000 /* 01=100Mbs */ #define MII_ATLX_PSSR_1000MBS 0x8000 /* 10=1000Mbs */ #define MII_DBG_ADDR 0x1D #define MII_DBG_DATA 0x1E /* PCI Command Register Bit Definitions */ #define PCI_REG_COMMAND 0x04 /* PCI Command Register */ #define CMD_IO_SPACE 0x0001 #define CMD_MEMORY_SPACE 0x0002 #define CMD_BUS_MASTER 0x0004 /* Wake Up Filter Control */ #define ATLX_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */ #define ATLX_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */ #define ATLX_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */ #define ATLX_WUFC_MC 0x00000008 /* Multicast Wakeup Enable */ #define ATLX_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */ #define ADVERTISE_10_HALF 0x0001 #define ADVERTISE_10_FULL 0x0002 #define ADVERTISE_100_HALF 0x0004 #define ADVERTISE_100_FULL 0x0008 #define ADVERTISE_1000_HALF 0x0010 #define ADVERTISE_1000_FULL 0x0020 #define AUTONEG_ADVERTISE_10_100_ALL 0x000F /* All 10/100 speeds */ #define AUTONEG_ADVERTISE_10_ALL 0x0003 /* 10Mbps Full & Half speeds */ #define PHY_AUTO_NEG_TIME 45 /* 4.5 Seconds */ #define PHY_FORCE_TIME 20 /* 2.0 Seconds */ /* For checksumming, the sum of all words in the EEPROM should equal 0xBABA */ #define EEPROM_SUM 0xBABA struct atlx_spi_flash_dev { const char *manu_name; /* manufacturer id */ /* op-code */ u8 cmd_wrsr; u8 cmd_read; u8 cmd_program; u8 cmd_wren; u8 cmd_wrdi; u8 cmd_rdsr; u8 cmd_rdid; u8 cmd_sector_erase; u8 cmd_chip_erase; }; #endif /* ATLX_H */