1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
|
Altera SoCFPGA ECC Manager
This driver uses the EDAC framework to implement the SOCFPGA ECC Manager.
The ECC Manager counts and corrects single bit errors and counts/handles
double bit errors which are uncorrectable.
Cyclone5 and Arria5 ECC Manager
Required Properties:
- compatible : Should be "altr,socfpga-ecc-manager"
- #address-cells: must be 1
- #size-cells: must be 1
- ranges : standard definition, should translate from local addresses
Subcomponents:
L2 Cache ECC
Required Properties:
- compatible : Should be "altr,socfpga-l2-ecc"
- reg : Address and size for ECC error interrupt clear registers.
- interrupts : Should be single bit error interrupt, then double bit error
interrupt. Note the rising edge type.
On Chip RAM ECC
Required Properties:
- compatible : Should be "altr,socfpga-ocram-ecc"
- reg : Address and size for ECC error interrupt clear registers.
- iram : phandle to On-Chip RAM definition.
- interrupts : Should be single bit error interrupt, then double bit error
interrupt. Note the rising edge type.
Example:
eccmgr: eccmgr@ffd08140 {
compatible = "altr,socfpga-ecc-manager";
#address-cells = <1>;
#size-cells = <1>;
ranges;
l2-ecc@ffd08140 {
compatible = "altr,socfpga-l2-ecc";
reg = <0xffd08140 0x4>;
interrupts = <0 36 1>, <0 37 1>;
};
ocram-ecc@ffd08144 {
compatible = "altr,socfpga-ocram-ecc";
reg = <0xffd08144 0x4>;
iram = <&ocram>;
interrupts = <0 178 1>, <0 179 1>;
};
};
Arria10 SoCFPGA ECC Manager
The Arria10 SoC ECC Manager handles the IRQs for each peripheral
in a shared register instead of individual IRQs like the Cyclone5
and Arria5. Therefore the device tree is different as well.
Required Properties:
- compatible : Should be "altr,socfpga-a10-ecc-manager"
- altr,sysgr-syscon : phandle to Arria10 System Manager Block
containing the ECC manager registers.
- #address-cells: must be 1
- #size-cells: must be 1
- interrupts : Should be single bit error interrupt, then double bit error
interrupt.
- interrupt-controller : boolean indicator that ECC Manager is an interrupt controller
- #interrupt-cells : must be set to 2.
- ranges : standard definition, should translate from local addresses
Subcomponents:
L2 Cache ECC
Required Properties:
- compatible : Should be "altr,socfpga-a10-l2-ecc"
- reg : Address and size for ECC error interrupt clear registers.
- interrupts : Should be single bit error interrupt, then double bit error
interrupt, in this order.
On-Chip RAM ECC
Required Properties:
- compatible : Should be "altr,socfpga-a10-ocram-ecc"
- reg : Address and size for ECC block registers.
- interrupts : Should be single bit error interrupt, then double bit error
interrupt, in this order.
Ethernet FIFO ECC
Required Properties:
- compatible : Should be "altr,socfpga-eth-mac-ecc"
- reg : Address and size for ECC block registers.
- altr,ecc-parent : phandle to parent Ethernet node.
- interrupts : Should be single bit error interrupt, then double bit error
interrupt, in this order.
NAND FIFO ECC
Required Properties:
- compatible : Should be "altr,socfpga-nand-ecc"
- reg : Address and size for ECC block registers.
- altr,ecc-parent : phandle to parent NAND node.
- interrupts : Should be single bit error interrupt, then double bit error
interrupt, in this order.
DMA FIFO ECC
Required Properties:
- compatible : Should be "altr,socfpga-dma-ecc"
- reg : Address and size for ECC block registers.
- altr,ecc-parent : phandle to parent DMA node.
- interrupts : Should be single bit error interrupt, then double bit error
interrupt, in this order.
USB FIFO ECC
Required Properties:
- compatible : Should be "altr,socfpga-usb-ecc"
- reg : Address and size for ECC block registers.
- altr,ecc-parent : phandle to parent USB node.
- interrupts : Should be single bit error interrupt, then double bit error
interrupt, in this order.
QSPI FIFO ECC
Required Properties:
- compatible : Should be "altr,socfpga-qspi-ecc"
- reg : Address and size for ECC block registers.
- altr,ecc-parent : phandle to parent QSPI node.
- interrupts : Should be single bit error interrupt, then double bit error
interrupt, in this order.
SDMMC FIFO ECC
Required Properties:
- compatible : Should be "altr,socfpga-sdmmc-ecc"
- reg : Address and size for ECC block registers.
- altr,ecc-parent : phandle to parent SD/MMC node.
- interrupts : Should be single bit error interrupt, then double bit error
interrupt, in this order for port A, and then single bit error interrupt,
then double bit error interrupt in this order for port B.
Example:
eccmgr: eccmgr@ffd06000 {
compatible = "altr,socfpga-a10-ecc-manager";
altr,sysmgr-syscon = <&sysmgr>;
#address-cells = <1>;
#size-cells = <1>;
interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>,
<0 0 IRQ_TYPE_LEVEL_HIGH>;
interrupt-controller;
#interrupt-cells = <2>;
ranges;
l2-ecc@ffd06010 {
compatible = "altr,socfpga-a10-l2-ecc";
reg = <0xffd06010 0x4>;
interrupts = <0 IRQ_TYPE_LEVEL_HIGH>,
<32 IRQ_TYPE_LEVEL_HIGH>;
};
ocram-ecc@ff8c3000 {
compatible = "altr,socfpga-a10-ocram-ecc";
reg = <0xff8c3000 0x90>;
interrupts = <1 IRQ_TYPE_LEVEL_HIGH>,
<33 IRQ_TYPE_LEVEL_HIGH> ;
};
emac0-rx-ecc@ff8c0800 {
compatible = "altr,socfpga-eth-mac-ecc";
reg = <0xff8c0800 0x400>;
altr,ecc-parent = <&gmac0>;
interrupts = <4 IRQ_TYPE_LEVEL_HIGH>,
<36 IRQ_TYPE_LEVEL_HIGH>;
};
emac0-tx-ecc@ff8c0c00 {
compatible = "altr,socfpga-eth-mac-ecc";
reg = <0xff8c0c00 0x400>;
altr,ecc-parent = <&gmac0>;
interrupts = <5 IRQ_TYPE_LEVEL_HIGH>,
<37 IRQ_TYPE_LEVEL_HIGH>;
};
nand-buf-ecc@ff8c2000 {
compatible = "altr,socfpga-nand-ecc";
reg = <0xff8c2000 0x400>;
altr,ecc-parent = <&nand>;
interrupts = <11 IRQ_TYPE_LEVEL_HIGH>,
<43 IRQ_TYPE_LEVEL_HIGH>;
};
nand-rd-ecc@ff8c2400 {
compatible = "altr,socfpga-nand-ecc";
reg = <0xff8c2400 0x400>;
altr,ecc-parent = <&nand>;
interrupts = <13 IRQ_TYPE_LEVEL_HIGH>,
<45 IRQ_TYPE_LEVEL_HIGH>;
};
nand-wr-ecc@ff8c2800 {
compatible = "altr,socfpga-nand-ecc";
reg = <0xff8c2800 0x400>;
altr,ecc-parent = <&nand>;
interrupts = <12 IRQ_TYPE_LEVEL_HIGH>,
<44 IRQ_TYPE_LEVEL_HIGH>;
};
dma-ecc@ff8c8000 {
compatible = "altr,socfpga-dma-ecc";
reg = <0xff8c8000 0x400>;
altr,ecc-parent = <&pdma>;
interrupts = <10 IRQ_TYPE_LEVEL_HIGH>,
<42 IRQ_TYPE_LEVEL_HIGH>;
usb0-ecc@ff8c8800 {
compatible = "altr,socfpga-usb-ecc";
reg = <0xff8c8800 0x400>;
altr,ecc-parent = <&usb0>;
interrupts = <2 IRQ_TYPE_LEVEL_HIGH>,
<34 IRQ_TYPE_LEVEL_HIGH>;
};
qspi-ecc@ff8c8400 {
compatible = "altr,socfpga-qspi-ecc";
reg = <0xff8c8400 0x400>;
altr,ecc-parent = <&qspi>;
interrupts = <14 IRQ_TYPE_LEVEL_HIGH>,
<46 IRQ_TYPE_LEVEL_HIGH>;
};
sdmmc-ecc@ff8c2c00 {
compatible = "altr,socfpga-sdmmc-ecc";
reg = <0xff8c2c00 0x400>;
altr,ecc-parent = <&mmc>;
interrupts = <15 IRQ_TYPE_LEVEL_HIGH>,
<47 IRQ_TYPE_LEVEL_HIGH>,
<16 IRQ_TYPE_LEVEL_HIGH>,
<48 IRQ_TYPE_LEVEL_HIGH>;
};
};
Stratix10 SoCFPGA ECC Manager (ARM64)
The Stratix10 SoC ECC Manager handles the IRQs for each peripheral
in a shared register similar to the Arria10. However, Stratix10 ECC
requires access to registers that can only be read from Secure Monitor
with SMC calls. Therefore the device tree is slightly different. Note
that only 1 interrupt is sent in Stratix10 because the double bit errors
are treated as SErrors in ARM64 instead of IRQs in ARM32.
Required Properties:
- compatible : Should be "altr,socfpga-s10-ecc-manager"
- altr,sysgr-syscon : phandle to Stratix10 System Manager Block
containing the ECC manager registers.
- interrupts : Should be single bit error interrupt.
- interrupt-controller : boolean indicator that ECC Manager is an interrupt controller
- #interrupt-cells : must be set to 2.
- #address-cells: must be 1
- #size-cells: must be 1
- ranges : standard definition, should translate from local addresses
Subcomponents:
SDRAM ECC
Required Properties:
- compatible : Should be "altr,sdram-edac-s10"
- interrupts : Should be single bit error interrupt.
On-Chip RAM ECC
Required Properties:
- compatible : Should be "altr,socfpga-s10-ocram-ecc"
- reg : Address and size for ECC block registers.
- altr,ecc-parent : phandle to parent OCRAM node.
- interrupts : Should be single bit error interrupt.
Ethernet FIFO ECC
Required Properties:
- compatible : Should be "altr,socfpga-s10-eth-mac-ecc"
- reg : Address and size for ECC block registers.
- altr,ecc-parent : phandle to parent Ethernet node.
- interrupts : Should be single bit error interrupt.
NAND FIFO ECC
Required Properties:
- compatible : Should be "altr,socfpga-s10-nand-ecc"
- reg : Address and size for ECC block registers.
- altr,ecc-parent : phandle to parent NAND node.
- interrupts : Should be single bit error interrupt.
DMA FIFO ECC
Required Properties:
- compatible : Should be "altr,socfpga-s10-dma-ecc"
- reg : Address and size for ECC block registers.
- altr,ecc-parent : phandle to parent DMA node.
- interrupts : Should be single bit error interrupt.
USB FIFO ECC
Required Properties:
- compatible : Should be "altr,socfpga-s10-usb-ecc"
- reg : Address and size for ECC block registers.
- altr,ecc-parent : phandle to parent USB node.
- interrupts : Should be single bit error interrupt.
SDMMC FIFO ECC
Required Properties:
- compatible : Should be "altr,socfpga-s10-sdmmc-ecc"
- reg : Address and size for ECC block registers.
- altr,ecc-parent : phandle to parent SD/MMC node.
- interrupts : Should be single bit error interrupt for port A
and then single bit error interrupt for port B.
Example:
eccmgr {
compatible = "altr,socfpga-s10-ecc-manager";
altr,sysmgr-syscon = <&sysmgr>;
#address-cells = <1>;
#size-cells = <1>;
interrupts = <0 15 4>;
interrupt-controller;
#interrupt-cells = <2>;
ranges;
sdramedac {
compatible = "altr,sdram-edac-s10";
interrupts = <16 IRQ_TYPE_LEVEL_HIGH>;
};
ocram-ecc@ff8cc000 {
compatible = "altr,socfpga-s10-ocram-ecc";
reg = <ff8cc000 0x100>;
altr,ecc-parent = <&ocram>;
interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
};
emac0-rx-ecc@ff8c0000 {
compatible = "altr,socfpga-s10-eth-mac-ecc";
reg = <0xff8c0000 0x100>;
altr,ecc-parent = <&gmac0>;
interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
};
emac0-tx-ecc@ff8c0400 {
compatible = "altr,socfpga-s10-eth-mac-ecc";
reg = <0xff8c0400 0x100>;
altr,ecc-parent = <&gmac0>;
interrupts = <5 IRQ_TYPE_LEVEL_HIGH>'
};
nand-buf-ecc@ff8c8000 {
compatible = "altr,socfpga-s10-nand-ecc";
reg = <0xff8c8000 0x100>;
altr,ecc-parent = <&nand>;
interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
};
nand-rd-ecc@ff8c8400 {
compatible = "altr,socfpga-s10-nand-ecc";
reg = <0xff8c8400 0x100>;
altr,ecc-parent = <&nand>;
interrupts = <13 IRQ_TYPE_LEVEL_HIGH>;
};
nand-wr-ecc@ff8c8800 {
compatible = "altr,socfpga-s10-nand-ecc";
reg = <0xff8c8800 0x100>;
altr,ecc-parent = <&nand>;
interrupts = <12 IRQ_TYPE_LEVEL_HIGH>;
};
dma-ecc@ff8c9000 {
compatible = "altr,socfpga-s10-dma-ecc";
reg = <0xff8c9000 0x100>;
altr,ecc-parent = <&pdma>;
interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
usb0-ecc@ff8c4000 {
compatible = "altr,socfpga-s10-usb-ecc";
reg = <0xff8c4000 0x100>;
altr,ecc-parent = <&usb0>;
interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
};
sdmmc-ecc@ff8c8c00 {
compatible = "altr,socfpga-s10-sdmmc-ecc";
reg = <0xff8c8c00 0x100>;
altr,ecc-parent = <&mmc>;
interrupts = <14 IRQ_TYPE_LEVEL_HIGH>,
<15 IRQ_TYPE_LEVEL_HIGH>;
};
};
|
