1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
|
==============================
PXA2xx SPI on SSP driver HOWTO
==============================
This a mini HOWTO on the pxa2xx_spi driver. The driver turns a PXA2xx
synchronous serial port into an SPI host controller
(see Documentation/spi/spi-summary.rst). The driver has the following features
- Support for any PXA2xx and compatible SSP.
- SSP PIO and SSP DMA data transfers.
- External and Internal (SSPFRM) chip selects.
- Per peripheral device (chip) configuration.
- Full suspend, freeze, resume support.
The driver is built around a &struct spi_message FIFO serviced by kernel
thread. The kernel thread, spi_pump_messages(), drives message FIFO and
is responsible for queuing SPI transactions and setting up and launching
the DMA or interrupt driven transfers.
Declaring PXA2xx host controllers
---------------------------------
Typically, for a legacy platform, an SPI host controller is defined in the
arch/.../mach-*/board-*.c as a "platform device". The host controller configuration
is passed to the driver via a table found in include/linux/spi/pxa2xx_spi.h::
struct pxa2xx_spi_controller {
u16 num_chipselect;
u8 enable_dma;
...
};
The "pxa2xx_spi_controller.num_chipselect" field is used to determine the number of
peripheral devices (chips) attached to this SPI host controller.
The "pxa2xx_spi_controller.enable_dma" field informs the driver that SSP DMA should
be used. This caused the driver to acquire two DMA channels: Rx channel and
Tx channel. The Rx channel has a higher DMA service priority than the Tx channel.
See the "PXA2xx Developer Manual" section "DMA Controller".
For the new platforms the description of the controller and peripheral devices
comes from Device Tree or ACPI.
NSSP HOST SAMPLE
----------------
Below is a sample configuration using the PXA255 NSSP for a legacy platform::
static struct resource pxa_spi_nssp_resources[] = {
[0] = {
.start = __PREG(SSCR0_P(2)), /* Start address of NSSP */
.end = __PREG(SSCR0_P(2)) + 0x2c, /* Range of registers */
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ_NSSP, /* NSSP IRQ */
.end = IRQ_NSSP,
.flags = IORESOURCE_IRQ,
},
};
static struct pxa2xx_spi_controller pxa_nssp_controller_info = {
.num_chipselect = 1, /* Matches the number of chips attached to NSSP */
.enable_dma = 1, /* Enables NSSP DMA */
};
static struct platform_device pxa_spi_nssp = {
.name = "pxa2xx-spi", /* MUST BE THIS VALUE, so device match driver */
.id = 2, /* Bus number, MUST MATCH SSP number 1..n */
.resource = pxa_spi_nssp_resources,
.num_resources = ARRAY_SIZE(pxa_spi_nssp_resources),
.dev = {
.platform_data = &pxa_nssp_controller_info, /* Passed to driver */
},
};
static struct platform_device *devices[] __initdata = {
&pxa_spi_nssp,
};
static void __init board_init(void)
{
(void)platform_add_device(devices, ARRAY_SIZE(devices));
}
Declaring peripheral devices
----------------------------
Typically, for a legacy platform, each SPI peripheral device (chip) is defined in the
arch/.../mach-*/board-*.c using the "spi_board_info" structure found in
"linux/spi/spi.h". See "Documentation/spi/spi-summary.rst" for additional
information.
Each peripheral device (chip) attached to the PXA2xx must provide specific chip configuration
information via the structure "pxa2xx_spi_chip" found in
"include/linux/spi/pxa2xx_spi.h". The PXA2xx host controller driver will use
the configuration whenever the driver communicates with the peripheral
device. All fields are optional.
::
struct pxa2xx_spi_chip {
u8 tx_threshold;
u8 rx_threshold;
u8 dma_burst_size;
u32 timeout;
};
The "pxa2xx_spi_chip.tx_threshold" and "pxa2xx_spi_chip.rx_threshold" fields are
used to configure the SSP hardware FIFO. These fields are critical to the
performance of pxa2xx_spi driver and misconfiguration will result in rx
FIFO overruns (especially in PIO mode transfers). Good default values are::
.tx_threshold = 8,
.rx_threshold = 8,
The range is 1 to 16 where zero indicates "use default".
The "pxa2xx_spi_chip.dma_burst_size" field is used to configure PXA2xx DMA
engine and is related the "spi_device.bits_per_word" field. Read and understand
the PXA2xx "Developer Manual" sections on the DMA controller and SSP Controllers
to determine the correct value. An SSP configured for byte-wide transfers would
use a value of 8. The driver will determine a reasonable default if
dma_burst_size == 0.
The "pxa2xx_spi_chip.timeout" fields is used to efficiently handle
trailing bytes in the SSP receiver FIFO. The correct value for this field is
dependent on the SPI bus speed ("spi_board_info.max_speed_hz") and the specific
peripheral device. Please note that the PXA2xx SSP 1 does not support trailing byte
timeouts and must busy-wait any trailing bytes.
NOTE: the SPI driver cannot control the chip select if SSPFRM is used, so the
chipselect is dropped after each spi_transfer. Most devices need chip select
asserted around the complete message. Use SSPFRM as a GPIO (through a descriptor)
to accommodate these chips.
NSSP PERIPHERAL SAMPLE
----------------------
For a legacy platform or in some other cases, the pxa2xx_spi_chip structure
is passed to the pxa2xx_spi driver in the "spi_board_info.controller_data"
field. Below is a sample configuration using the PXA255 NSSP.
::
static struct pxa2xx_spi_chip cs8415a_chip_info = {
.tx_threshold = 8, /* SSP hardware FIFO threshold */
.rx_threshold = 8, /* SSP hardware FIFO threshold */
.dma_burst_size = 8, /* Byte wide transfers used so 8 byte bursts */
.timeout = 235, /* See Intel documentation */
};
static struct pxa2xx_spi_chip cs8405a_chip_info = {
.tx_threshold = 8, /* SSP hardware FIFO threshold */
.rx_threshold = 8, /* SSP hardware FIFO threshold */
.dma_burst_size = 8, /* Byte wide transfers used so 8 byte bursts */
.timeout = 235, /* See Intel documentation */
};
static struct spi_board_info streetracer_spi_board_info[] __initdata = {
{
.modalias = "cs8415a", /* Name of spi_driver for this device */
.max_speed_hz = 3686400, /* Run SSP as fast a possible */
.bus_num = 2, /* Framework bus number */
.chip_select = 0, /* Framework chip select */
.platform_data = NULL; /* No spi_driver specific config */
.controller_data = &cs8415a_chip_info, /* Host controller config */
.irq = STREETRACER_APCI_IRQ, /* Peripheral device interrupt */
},
{
.modalias = "cs8405a", /* Name of spi_driver for this device */
.max_speed_hz = 3686400, /* Run SSP as fast a possible */
.bus_num = 2, /* Framework bus number */
.chip_select = 1, /* Framework chip select */
.controller_data = &cs8405a_chip_info, /* Host controller config */
.irq = STREETRACER_APCI_IRQ, /* Peripheral device interrupt */
},
};
static void __init streetracer_init(void)
{
spi_register_board_info(streetracer_spi_board_info,
ARRAY_SIZE(streetracer_spi_board_info));
}
DMA and PIO I/O Support
-----------------------
The pxa2xx_spi driver supports both DMA and interrupt driven PIO message
transfers. The driver defaults to PIO mode and DMA transfers must be enabled
by setting the "enable_dma" flag in the "pxa2xx_spi_controller" structure.
For the newer platforms, that are known to support DMA, the driver will enable
it automatically and try it first with a possible fallback to PIO. The DMA
mode supports both coherent and stream based DMA mappings.
The following logic is used to determine the type of I/O to be used on
a per "spi_transfer" basis::
if spi_message.len > 65536 then
if spi_message.is_dma_mapped or rx_dma_buf != 0 or tx_dma_buf != 0 then
reject premapped transfers
print "rate limited" warning
use PIO transfers
if enable_dma and the size is in the range [DMA burst size..65536] then
use streaming DMA mode
otherwise
use PIO transfer
THANKS TO
---------
David Brownell and others for mentoring the development of this driver.
|
