path: root/debian/patches-rt/0012-serial-8250_omap-Use-port-lock-wrappers.patch

From: Thomas Gleixner <tglx@linutronix.de>
Date: Thu, 14 Sep 2023 20:43:29 +0206
Subject: [PATCH 012/134] serial: 8250_omap: Use port lock wrappers
Origin: https://www.kernel.org/pub/linux/kernel/projects/rt/6.6/older/patches-6.6.7-rt18.tar.xz

When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.

So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.

All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.

To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.

Converted with coccinelle. No functional change.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-13-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
---
 drivers/tty/serial/8250/8250_omap.c |   52 ++++++++++++++++++------------------
 1 file changed, 26 insertions(+), 26 deletions(-)

--- a/drivers/tty/serial/8250/8250_omap.c
+++ b/drivers/tty/serial/8250/8250_omap.c
@@ -401,7 +401,7 @@ static void omap_8250_set_termios(struct
 	 * interrupts disabled.
 	 */
 	pm_runtime_get_sync(port->dev);
-	spin_lock_irq(&port->lock);
+	uart_port_lock_irq(port);
 
 	/*
 	 * Update the per-port timeout.
@@ -504,7 +504,7 @@ static void omap_8250_set_termios(struct
 	}
 	omap8250_restore_regs(up);
 
-	spin_unlock_irq(&up->port.lock);
+	uart_port_unlock_irq(&up->port);
 	pm_runtime_mark_last_busy(port->dev);
 	pm_runtime_put_autosuspend(port->dev);
 
@@ -529,7 +529,7 @@ static void omap_8250_pm(struct uart_por
 	pm_runtime_get_sync(port->dev);
 
 	/* Synchronize UART_IER access against the console. */
-	spin_lock_irq(&port->lock);
+	uart_port_lock_irq(port);
 
 	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
 	efr = serial_in(up, UART_EFR);
@@ -541,7 +541,7 @@ static void omap_8250_pm(struct uart_por
 	serial_out(up, UART_EFR, efr);
 	serial_out(up, UART_LCR, 0);
 
-	spin_unlock_irq(&port->lock);
+	uart_port_unlock_irq(port);
 
 	pm_runtime_mark_last_busy(port->dev);
 	pm_runtime_put_autosuspend(port->dev);
@@ -660,7 +660,7 @@ static irqreturn_t omap8250_irq(int irq,
 		unsigned long delay;
 
 		/* Synchronize UART_IER access against the console. */
-		spin_lock(&port->lock);
+		uart_port_lock(port);
 		up->ier = port->serial_in(port, UART_IER);
 		if (up->ier & (UART_IER_RLSI | UART_IER_RDI)) {
 			port->ops->stop_rx(port);
@@ -670,7 +670,7 @@ static irqreturn_t omap8250_irq(int irq,
 			 */
 			cancel_delayed_work(&up->overrun_backoff);
 		}
-		spin_unlock(&port->lock);
+		uart_port_unlock(port);
 
 		delay = msecs_to_jiffies(up->overrun_backoff_time_ms);
 		schedule_delayed_work(&up->overrun_backoff, delay);
@@ -717,10 +717,10 @@ static int omap_8250_startup(struct uart
 	}
 
 	/* Synchronize UART_IER access against the console. */
-	spin_lock_irq(&port->lock);
+	uart_port_lock_irq(port);
 	up->ier = UART_IER_RLSI | UART_IER_RDI;
 	serial_out(up, UART_IER, up->ier);
-	spin_unlock_irq(&port->lock);
+	uart_port_unlock_irq(port);
 
 #ifdef CONFIG_PM
 	up->capabilities |= UART_CAP_RPM;
@@ -733,9 +733,9 @@ static int omap_8250_startup(struct uart
 	serial_out(up, UART_OMAP_WER, priv->wer);
 
 	if (up->dma && !(priv->habit & UART_HAS_EFR2)) {
-		spin_lock_irq(&port->lock);
+		uart_port_lock_irq(port);
 		up->dma->rx_dma(up);
-		spin_unlock_irq(&port->lock);
+		uart_port_unlock_irq(port);
 	}
 
 	enable_irq(up->port.irq);
@@ -761,10 +761,10 @@ static void omap_8250_shutdown(struct ua
 		serial_out(up, UART_OMAP_EFR2, 0x0);
 
 	/* Synchronize UART_IER access against the console. */
-	spin_lock_irq(&port->lock);
+	uart_port_lock_irq(port);
 	up->ier = 0;
 	serial_out(up, UART_IER, 0);
-	spin_unlock_irq(&port->lock);
+	uart_port_unlock_irq(port);
 	disable_irq_nosync(up->port.irq);
 	dev_pm_clear_wake_irq(port->dev);
 
@@ -789,10 +789,10 @@ static void omap_8250_throttle(struct ua
 
 	pm_runtime_get_sync(port->dev);
 
-	spin_lock_irqsave(&port->lock, flags);
+	uart_port_lock_irqsave(port, &flags);
 	port->ops->stop_rx(port);
 	priv->throttled = true;
-	spin_unlock_irqrestore(&port->lock, flags);
+	uart_port_unlock_irqrestore(port, flags);
 
 	pm_runtime_mark_last_busy(port->dev);
 	pm_runtime_put_autosuspend(port->dev);
@@ -807,14 +807,14 @@ static void omap_8250_unthrottle(struct
 	pm_runtime_get_sync(port->dev);
 
 	/* Synchronize UART_IER access against the console. */
-	spin_lock_irqsave(&port->lock, flags);
+	uart_port_lock_irqsave(port, &flags);
 	priv->throttled = false;
 	if (up->dma)
 		up->dma->rx_dma(up);
 	up->ier |= UART_IER_RLSI | UART_IER_RDI;
 	port->read_status_mask |= UART_LSR_DR;
 	serial_out(up, UART_IER, up->ier);
-	spin_unlock_irqrestore(&port->lock, flags);
+	uart_port_unlock_irqrestore(port, flags);
 
 	pm_runtime_mark_last_busy(port->dev);
 	pm_runtime_put_autosuspend(port->dev);
@@ -958,7 +958,7 @@ static void __dma_rx_complete(void *para
 	unsigned long flags;
 
 	/* Synchronize UART_IER access against the console. */
-	spin_lock_irqsave(&p->port.lock, flags);
+	uart_port_lock_irqsave(&p->port, &flags);
 
 	/*
 	 * If the tx status is not DMA_COMPLETE, then this is a delayed
@@ -967,7 +967,7 @@ static void __dma_rx_complete(void *para
 	 */
 	if (dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state) !=
 			DMA_COMPLETE) {
-		spin_unlock_irqrestore(&p->port.lock, flags);
+		uart_port_unlock_irqrestore(&p->port, flags);
 		return;
 	}
 	__dma_rx_do_complete(p);
@@ -978,7 +978,7 @@ static void __dma_rx_complete(void *para
 			omap_8250_rx_dma(p);
 	}
 
-	spin_unlock_irqrestore(&p->port.lock, flags);
+	uart_port_unlock_irqrestore(&p->port, flags);
 }
 
 static void omap_8250_rx_dma_flush(struct uart_8250_port *p)
@@ -1083,7 +1083,7 @@ static void omap_8250_dma_tx_complete(vo
 	dma_sync_single_for_cpu(dma->txchan->device->dev, dma->tx_addr,
 				UART_XMIT_SIZE, DMA_TO_DEVICE);
 
-	spin_lock_irqsave(&p->port.lock, flags);
+	uart_port_lock_irqsave(&p->port, &flags);
 
 	dma->tx_running = 0;
 
@@ -1112,7 +1112,7 @@ static void omap_8250_dma_tx_complete(vo
 		serial8250_set_THRI(p);
 	}
 
-	spin_unlock_irqrestore(&p->port.lock, flags);
+	uart_port_unlock_irqrestore(&p->port, flags);
 }
 
 static int omap_8250_tx_dma(struct uart_8250_port *p)
@@ -1278,7 +1278,7 @@ static int omap_8250_dma_handle_irq(stru
 		return IRQ_HANDLED;
 	}
 
-	spin_lock(&port->lock);
+	uart_port_lock(port);
 
 	status = serial_port_in(port, UART_LSR);
 
@@ -1756,15 +1756,15 @@ static int omap8250_runtime_resume(struc
 		up = serial8250_get_port(priv->line);
 
 	if (up && omap8250_lost_context(up)) {
-		spin_lock_irq(&up->port.lock);
+		uart_port_lock_irq(&up->port);
 		omap8250_restore_regs(up);
-		spin_unlock_irq(&up->port.lock);
+		uart_port_unlock_irq(&up->port);
 	}
 
 	if (up && up->dma && up->dma->rxchan && !(priv->habit & UART_HAS_EFR2)) {
-		spin_lock_irq(&up->port.lock);
+		uart_port_lock_irq(&up->port);
 		omap_8250_rx_dma(up);
-		spin_unlock_irq(&up->port.lock);
+		uart_port_unlock_irq(&up->port);
 	}
 
 	priv->latency = priv->calc_latency;