1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
|
// SPDX-License-Identifier: GPL-2.0
/* Driver for the Texas Instruments DP83TG720 PHY
* Copyright (c) 2023 Pengutronix, Oleksij Rempel <kernel@pengutronix.de>
*/
#include <linux/bitfield.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/phy.h>
#define DP83TG720S_PHY_ID 0x2000a284
/* MDIO_MMD_VEND2 registers */
#define DP83TG720S_MII_REG_10 0x10
#define DP83TG720S_STS_MII_INT BIT(7)
#define DP83TG720S_LINK_STATUS BIT(0)
#define DP83TG720S_PHY_RESET 0x1f
#define DP83TG720S_HW_RESET BIT(15)
#define DP83TG720S_LPS_CFG3 0x18c
/* Power modes are documented as bit fields but used as values */
/* Power Mode 0 is Normal mode */
#define DP83TG720S_LPS_CFG3_PWR_MODE_0 BIT(0)
#define DP83TG720S_RGMII_DELAY_CTRL 0x602
/* In RGMII mode, Enable or disable the internal delay for RXD */
#define DP83TG720S_RGMII_RX_CLK_SEL BIT(1)
/* In RGMII mode, Enable or disable the internal delay for TXD */
#define DP83TG720S_RGMII_TX_CLK_SEL BIT(0)
#define DP83TG720S_SQI_REG_1 0x871
#define DP83TG720S_SQI_OUT_WORST GENMASK(7, 5)
#define DP83TG720S_SQI_OUT GENMASK(3, 1)
#define DP83TG720_SQI_MAX 7
static int dp83tg720_config_aneg(struct phy_device *phydev)
{
int ret;
/* Autoneg is not supported and this PHY supports only one speed.
* We need to care only about master/slave configuration if it was
* changed by user.
*/
ret = genphy_c45_pma_baset1_setup_master_slave(phydev);
if (ret)
return ret;
/* Re-read role configuration to make changes visible even if
* the link is in administrative down state.
*/
return genphy_c45_pma_baset1_read_master_slave(phydev);
}
static int dp83tg720_read_status(struct phy_device *phydev)
{
u16 phy_sts;
int ret;
phydev->pause = 0;
phydev->asym_pause = 0;
/* Most of Clause 45 registers are not present, so we can't use
* genphy_c45_read_status() here.
*/
phy_sts = phy_read(phydev, DP83TG720S_MII_REG_10);
phydev->link = !!(phy_sts & DP83TG720S_LINK_STATUS);
if (!phydev->link) {
/* According to the "DP83TC81x, DP83TG72x Software
* Implementation Guide", the PHY needs to be reset after a
* link loss or if no link is created after at least 100ms.
*
* Currently we are polling with the PHY_STATE_TIME (1000ms)
* interval, which is still enough for not automotive use cases.
*/
ret = phy_init_hw(phydev);
if (ret)
return ret;
/* After HW reset we need to restore master/slave configuration.
* genphy_c45_pma_baset1_read_master_slave() call will be done
* by the dp83tg720_config_aneg() function.
*/
ret = dp83tg720_config_aneg(phydev);
if (ret)
return ret;
phydev->speed = SPEED_UNKNOWN;
phydev->duplex = DUPLEX_UNKNOWN;
} else {
/* PMA/PMD control 1 register (Register 1.0) is present, but it
* doesn't contain the link speed information.
* So genphy_c45_read_pma() can't be used here.
*/
ret = genphy_c45_pma_baset1_read_master_slave(phydev);
if (ret)
return ret;
phydev->duplex = DUPLEX_FULL;
phydev->speed = SPEED_1000;
}
return 0;
}
static int dp83tg720_get_sqi(struct phy_device *phydev)
{
int ret;
if (!phydev->link)
return 0;
ret = phy_read_mmd(phydev, MDIO_MMD_VEND2, DP83TG720S_SQI_REG_1);
if (ret < 0)
return ret;
return FIELD_GET(DP83TG720S_SQI_OUT, ret);
}
static int dp83tg720_get_sqi_max(struct phy_device *phydev)
{
return DP83TG720_SQI_MAX;
}
static int dp83tg720_config_rgmii_delay(struct phy_device *phydev)
{
u16 rgmii_delay_mask;
u16 rgmii_delay = 0;
switch (phydev->interface) {
case PHY_INTERFACE_MODE_RGMII:
rgmii_delay = 0;
break;
case PHY_INTERFACE_MODE_RGMII_ID:
rgmii_delay = DP83TG720S_RGMII_RX_CLK_SEL |
DP83TG720S_RGMII_TX_CLK_SEL;
break;
case PHY_INTERFACE_MODE_RGMII_RXID:
rgmii_delay = DP83TG720S_RGMII_RX_CLK_SEL;
break;
case PHY_INTERFACE_MODE_RGMII_TXID:
rgmii_delay = DP83TG720S_RGMII_TX_CLK_SEL;
break;
default:
return 0;
}
rgmii_delay_mask = DP83TG720S_RGMII_RX_CLK_SEL |
DP83TG720S_RGMII_TX_CLK_SEL;
return phy_modify_mmd(phydev, MDIO_MMD_VEND2,
DP83TG720S_RGMII_DELAY_CTRL, rgmii_delay_mask,
rgmii_delay);
}
static int dp83tg720_config_init(struct phy_device *phydev)
{
int ret;
/* Software Restart is not enough to recover from a link failure.
* Using Hardware Reset instead.
*/
ret = phy_write(phydev, DP83TG720S_PHY_RESET, DP83TG720S_HW_RESET);
if (ret)
return ret;
/* Wait until MDC can be used again.
* The wait value of one 1ms is documented in "DP83TG720S-Q1 1000BASE-T1
* Automotive Ethernet PHY with SGMII and RGMII" datasheet.
*/
usleep_range(1000, 2000);
if (phy_interface_is_rgmii(phydev)) {
ret = dp83tg720_config_rgmii_delay(phydev);
if (ret)
return ret;
}
/* In case the PHY is bootstrapped in managed mode, we need to
* wake it.
*/
ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, DP83TG720S_LPS_CFG3,
DP83TG720S_LPS_CFG3_PWR_MODE_0);
if (ret)
return ret;
/* Make role configuration visible for ethtool on init and after
* rest.
*/
return genphy_c45_pma_baset1_read_master_slave(phydev);
}
static struct phy_driver dp83tg720_driver[] = {
{
PHY_ID_MATCH_MODEL(DP83TG720S_PHY_ID),
.name = "TI DP83TG720S",
.config_aneg = dp83tg720_config_aneg,
.read_status = dp83tg720_read_status,
.get_features = genphy_c45_pma_read_ext_abilities,
.config_init = dp83tg720_config_init,
.get_sqi = dp83tg720_get_sqi,
.get_sqi_max = dp83tg720_get_sqi_max,
.suspend = genphy_suspend,
.resume = genphy_resume,
} };
module_phy_driver(dp83tg720_driver);
static struct mdio_device_id __maybe_unused dp83tg720_tbl[] = {
{ PHY_ID_MATCH_MODEL(DP83TG720S_PHY_ID) },
{ }
};
MODULE_DEVICE_TABLE(mdio, dp83tg720_tbl);
MODULE_DESCRIPTION("Texas Instruments DP83TG720S PHY driver");
MODULE_AUTHOR("Oleksij Rempel <kernel@pengutronix.de>");
MODULE_LICENSE("GPL");
|
