1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
|
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* max8998.h - Voltage regulator driver for the Maxim 8998
*
* Copyright (C) 2009-2010 Samsung Electrnoics
* Kyungmin Park <kyungmin.park@samsung.com>
* Marek Szyprowski <m.szyprowski@samsung.com>
*/
#ifndef __LINUX_MFD_MAX8998_H
#define __LINUX_MFD_MAX8998_H
#include <linux/regulator/machine.h>
/* MAX 8998 regulator ids */
enum {
MAX8998_LDO2 = 2,
MAX8998_LDO3,
MAX8998_LDO4,
MAX8998_LDO5,
MAX8998_LDO6,
MAX8998_LDO7,
MAX8998_LDO8,
MAX8998_LDO9,
MAX8998_LDO10,
MAX8998_LDO11,
MAX8998_LDO12,
MAX8998_LDO13,
MAX8998_LDO14,
MAX8998_LDO15,
MAX8998_LDO16,
MAX8998_LDO17,
MAX8998_BUCK1,
MAX8998_BUCK2,
MAX8998_BUCK3,
MAX8998_BUCK4,
MAX8998_EN32KHZ_AP,
MAX8998_EN32KHZ_CP,
MAX8998_ENVICHG,
MAX8998_ESAFEOUT1,
MAX8998_ESAFEOUT2,
MAX8998_CHARGER,
};
/**
* max8998_regulator_data - regulator data
* @id: regulator id
* @initdata: regulator init data (contraints, supplies, ...)
* @reg_node: DT node of regulator (unused on non-DT platforms)
*/
struct max8998_regulator_data {
int id;
struct regulator_init_data *initdata;
struct device_node *reg_node;
};
/**
* struct max8998_board - packages regulator init data
* @regulators: array of defined regulators
* @num_regulators: number of regulators used
* @irq_base: base IRQ number for max8998, required for IRQs
* @ono: power onoff IRQ number for max8998
* @buck_voltage_lock: Do NOT change the values of the following six
* registers set by buck?_voltage?. The voltage of BUCK1/2 cannot
* be other than the preset values.
* @buck1_voltage: BUCK1 DVS mode 1 voltage registers
* @buck2_voltage: BUCK2 DVS mode 2 voltage registers
* @buck1_default_idx: Default for BUCK1 gpio pin 1, 2
* @buck2_default_idx: Default for BUCK2 gpio pin.
* @wakeup: Allow to wake up from suspend
* @rtc_delay: LP3974 RTC chip bug that requires delay after a register
* write before reading it.
* @eoc: End of Charge Level in percent: 10% ~ 45% by 5% step
* If it equals 0, leave it unchanged.
* Otherwise, it is a invalid value.
* @restart: Restart Level in mV: 100, 150, 200, and -1 for disable.
* If it equals 0, leave it unchanged.
* Otherwise, it is a invalid value.
* @timeout: Full Timeout in hours: 5, 6, 7, and -1 for disable.
* If it equals 0, leave it unchanged.
* Otherwise, leave it unchanged.
*/
struct max8998_platform_data {
struct max8998_regulator_data *regulators;
int num_regulators;
unsigned int irq_base;
int ono;
bool buck_voltage_lock;
int buck1_voltage[4];
int buck2_voltage[2];
int buck1_default_idx;
int buck2_default_idx;
bool wakeup;
bool rtc_delay;
int eoc;
int restart;
int timeout;
};
#endif /* __LINUX_MFD_MAX8998_H */
|
