1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
|
.\" From jt@hplb.hpl.hp.com Thu Dec 19 18:31:49 1996
.\" From: Jean Tourrilhes <jt@hplb.hpl.hp.com>
.\" Address: HP Labs, Filton Road, Stoke Gifford, Bristol BS12 6QZ, U.K.
.\" Jean II - HPLB - '96
.\" wavelan.c.4
.\"
.\" Provenance of this page is unclear.
.\"
.\" SPDX-License-Identifier: GPL-1.0-or-later
.\"
.TH wavelan 4 2023-02-05 "Linux man-pages 6.04"
.SH NAME
wavelan \- AT&T GIS WaveLAN ISA device driver
.SH SYNOPSIS
.nf
.BI "insmod wavelan_cs.o [io=" B,B.. "] [ irq=" I,I.. "] [name=" N,N.. ]
.fi
.SH DESCRIPTION
.I This driver is obsolete:
it was removed in Linux 2.6.35.
.PP
.B wavelan
is the low-level device driver for the NCR / AT&T / Lucent
.B WaveLAN ISA
and Digital (DEC)
.B RoamAbout DS
wireless ethernet adapter.
This driver is available as a module or
might be compiled in the kernel.
This driver supports multiple cards
in both forms (up to 4) and allocates the next available ethernet
device (eth0..eth#) for each card found, unless a device name is
explicitly specified (see below).
This device name will be reported
in the kernel log file with the MAC address, NWID, and frequency used
by the card.
.SS Parameters
This section applies to the module form (parameters passed on the
.BR insmod (8)
command line).
If the driver is included in the kernel, use the
.I ether=IRQ,IO,NAME
syntax on the kernel command line.
.TP
.B io
Specify the list of base addresses where to search for wavelan cards
(setting by dip switch on the card).
If you don't specify any io
address, the driver will scan 0x390 and 0x3E0 addresses, which might
conflict with other hardware...
.TP
.B irq
Set the list of IRQs that each wavelan card should use (the value is
saved in permanent storage for future use).
.TP
.B name
Set the list of names to be used for each wavelan card device (name
used by
.BR ifconfig (8)).
.SS Wireless extensions
Use
.BR iwconfig (8)
to manipulate wireless extensions.
.SS NWID (or domain)
Set the network ID
.RI [ 0
to
.IR FFFF ]
or disable it
.RI [ off ].
As the NWID is stored in the card Permanent Storage Area, it will be
reused at any further invocation of the driver.
.SS Frequency & channels
For the 2.4\ GHz 2.00 Hardware, you are able to set the frequency by
specifying one of the 10 defined channels
.RI ( 2.412,
.I 2.422, 2.425, 2.4305, 2.432, 2.442, 2.452, 2.460, 2.462
or
.IR 2.484 )
or directly as a numeric value.
The frequency is changed immediately and
permanently.
Frequency availability depends on the regulations...
.SS Statistics spy
Set a list of MAC addresses in the driver (up to 8) and get the last
quality of link for each of those (see
.BR iwspy (8)).
.SS /proc/net/wireless
.I status
is the status reported by the modem.
.I Link quality
reports the quality of the modulation on the air (direct sequence
spread spectrum) [max = 16].
.I Level
and
.I Noise
refer to the signal level and noise level [max = 64].
The
.I crypt discarded packet
and
.I misc discarded packet
counters are not implemented.
.SS Private ioctl
You may use
.BR iwpriv (8)
to manipulate private ioctls.
.SS Quality and level threshold
Enables you to define the quality and level threshold used by the
modem (packet below that level are discarded).
.SS Histogram
This functionality makes it possible to set a number of
signal level intervals and
to count the number of packets received in each of those defined
intervals.
This distribution might be used to calculate the mean value
and standard deviation of the signal level.
.SS Specific notes
This driver fails to detect some
.B non-NCR/AT&T/Lucent
Wavelan cards.
If this happens for you, you must look in the source code on
how to add your card to the detection routine.
.PP
Some of the mentioned features are optional.
You may enable or disable
them by changing flags in the driver header and recompile.
.\" .SH AUTHOR
.\" Bruce Janson \[em] bruce@cs.usyd.edu.au
.\" .br
.\" Jean Tourrilhes \[em] jt@hplb.hpl.hp.com
.\" .br
.\" (and others; see source code for details)
.\"
.\" SEE ALSO part
.\"
.SH SEE ALSO
.BR wavelan_cs (4),
.BR ifconfig (8),
.BR insmod (8),
.BR iwconfig (8),
.BR iwpriv (8),
.BR iwspy (8)
|
