networkctl systemd networkctl 1 networkctl Query or modify the status of network links networkctl OPTIONS COMMAND LINK Description networkctl may be used to query or modify the state of the network links as seen by systemd-networkd. Please refer to systemd-networkd.service8 for an introduction to the basic concepts, functionality, and configuration syntax. Commands The following commands are understood: list PATTERN… Show a list of existing links and their status. If one or more PATTERNs are specified, only links matching one of them are shown. If no further arguments are specified shows all links, otherwise just the specified links. Produces output similar to: IDX LINK TYPE OPERATIONAL SETUP 1 lo loopback carrier unmanaged 2 eth0 ether routable configured 3 virbr0 ether no-carrier unmanaged 4 virbr0-nic ether off unmanaged 4 links listed. The operational status is one of the following: missing The device is missing. off The device is powered down. no-carrier The device is powered up, but does not yet have a carrier. dormant The device has a carrier, but is not yet ready for normal traffic. degraded-carrier One of the bonding or bridge slave network interfaces is in off, no-carrier, or dormant state, and the master interface has no address. carrier The link has carrier, or for bond or bridge master, all bonding or bridge slave network interfaces are enslaved to the master. degraded The link has carrier and addresses valid on the local link configured. For bond or bridge master this means that not all slave network interfaces have carrier but at least one does. enslaved The link has carrier and is enslaved to bond or bridge master network interface. routable The link has carrier and routable address configured. For bond or bridge master it is not necessary for all slave network interfaces to have carrier, but at least one must. The setup status is one of the following: pending systemd-udevd8 is still processing the link, we don't yet know if we will manage it. initialized systemd-udevd8 has processed the link, but we don't yet know if we will manage it. configuring Configuration for the link is being retrieved or the link is being configured. configured Link has been configured successfully. unmanaged systemd-networkd is not handling the link. failed systemd-networkd failed to configure the link. linger The link is gone, but has not yet been dropped by systemd-networkd. status PATTERN… Show information about the specified links: type, state, kernel module driver, hardware and IP address, configured DNS servers, etc. If one or more PATTERNs are specified, only links matching one of them are shown. When no links are specified, an overall network status is shown. Also see the option . Produces output similar to: ● State: routable Online state: online Address: 10.193.76.5 on eth0 192.168.122.1 on virbr0 169.254.190.105 on eth0 fe80::5054:aa:bbbb:cccc on eth0 Gateway: 10.193.11.1 (CISCO SYSTEMS, INC.) on eth0 DNS: 8.8.8.8 8.8.4.4 In the overall network status, the online state depends on the individual online state of all required links. Managed links are required for online by default. In this case, the online state is one of the following: unknown All links have unknown online status (i.e. there are no required links). offline All required links are offline. partial Some, but not all, required links are online. online All required links are online. lldp PATTERN… Show discovered LLDP (Link Layer Discovery Protocol) neighbors. If one or more PATTERNs are specified only neighbors on those interfaces are shown. Otherwise shows discovered neighbors on all interfaces. Note that for this feature to work, LLDP= must be turned on for the specific interface, see systemd.network5 for details. Produces output similar to: LINK CHASSIS ID SYSTEM NAME CAPS PORT ID PORT DESCRIPTION enp0s25 00:e0:4c:00:00:00 GS1900 ..b........ 2 Port #2 Capability Flags: o - Other; p - Repeater; b - Bridge; w - WLAN Access Point; r - Router; t - Telephone; d - DOCSIS cable device; a - Station; c - Customer VLAN; s - Service VLAN, m - Two-port MAC Relay (TPMR) 1 neighbors listed. label Show numerical address labels that can be used for address selection. This is the same information that ip-addrlabel8 shows. See RFC 3484 for a discussion of address labels. Produces output similar to: Prefix/Prefixlen Label ::/0 1 fc00::/7 5 fec0::/10 11 2002::/16 2 3ffe::/16 12 2001:10::/28 7 2001::/32 6 ::ffff:0.0.0.0/96 4 ::/96 3 ::1/128 0 delete DEVICE… Deletes virtual netdevs. Takes interface name or index number. up DEVICE… Bring devices up. Takes interface name or index number. down DEVICE… Bring devices down. Takes interface name or index number. renew DEVICE… Renew dynamic configurations e.g. addresses received from DHCP server. Takes interface name or index number. forcerenew DEVICE… Send a FORCERENEW message to all connected clients, triggering DHCP reconfiguration. Takes interface name or index number. reconfigure DEVICE… Reconfigure network interfaces. Takes interface name or index number. Note that this does not reload .netdev or .network corresponding to the specified interface. So, if you edit config files, it is necessary to call networkctl reload first to apply new settings. reload Reload .netdev and .network files. If a new .netdev file is found, then the corresponding netdev is created. Note that even if an existing .netdev is modified or removed, systemd-networkd does not update or remove the netdev. If a new, modified or removed .network file is found, then all interfaces which match the file are reconfigured. edit FILE|@DEVICE Edit network configuration files, which include .network, .netdev, and .link files. If no network config file matching the given name is found, a new one will be created under /etc/. Specially, if the name is prefixed by @, it will be treated as a network interface, and editing will be performed on the network config files associated with it. Additionally, the interface name can be suffixed with :network (default) or :link, in order to choose the type of network config to operate on. If is specified, edit the drop-in file instead of the main configuration file. Unless is specified, systemd-networkd will be reloaded after the edit of the .network or .netdev files finishes. The same applies for .link files and systemd-udevd8. Note that the changed link settings are not automatically applied after reloading. To achieve that, trigger uevents for the corresponding interface. Refer to systemd.link5 for more information. cat FILE|@DEVICE Show network configuration files. This command honors the @ prefix in the same way as edit. Options The following options are understood: Show all links with status. Show link statistics with status. Do not ellipsize the output. When used with status, controls the number of journal lines to show, counting from the most recent ones. Takes a positive integer argument. Defaults to 10. NAME When used with edit, edit the drop-in file NAME instead of the main configuration file. When used with edit, systemd-networkd.service8 or systemd-udevd.service8 will not be reloaded after the editing finishes. Exit status On success, 0 is returned, a non-zero failure code otherwise. See Also systemd-networkd.service8, systemd.network5, systemd.netdev5, ip8