- -

Multithreading options. - More...

- -

#include <container.h>

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

-Data Fields
uint32_t	flags
	Flags.

-uint32_t	threads
	Number of worker threads to use.

uint64_t	block_size
	Encoder only: Maximum uncompressed size of a Block.

uint32_t	timeout
	Timeout to allow lzma_code() to return early.

uint32_t	preset
	Encoder only: Compression preset.

const lzma_filter *	filters
	Encoder only: Filter chain (alternative to a preset)

lzma_check	check
	Encoder only: Integrity check type.

uint64_t	memlimit_threading
	Memory usage limit to reduce the number of threads.

uint64_t	memlimit_stop
	Memory usage limit that should never be exceeded.

-

Detailed Description

-

Multithreading options.

-

Field Documentation

- -

◆ flags

- -

-

- - - - -

uint32_t lzma_mt::flags

-

- -

Flags.

-

Set this to zero if no flags are wanted.

-

Encoder: No flags are currently supported.

-

Decoder: Bitwise-or of zero or more of the decoder flags:

LZMA_TELL_NO_CHECK
LZMA_TELL_UNSUPPORTED_CHECK
LZMA_TELL_ANY_CHECK
LZMA_IGNORE_CHECK
LZMA_CONCATENATED
LZMA_FAIL_FAST

- -

-

- -

◆ block_size

- -

-

- - - - -

uint64_t lzma_mt::block_size

-

- -

Encoder only: Maximum uncompressed size of a Block.

-

The encoder will start a new .xz Block every block_size bytes. Using LZMA_FULL_FLUSH or LZMA_FULL_BARRIER with lzma_code() the caller may tell liblzma to start a new Block earlier.

-

With LZMA2, a recommended block size is 2-4 times the LZMA2 dictionary size. With very small dictionaries, it is recommended to use at least 1 MiB block size for good compression ratio, even if this is more than four times the dictionary size. Note that these are only recommendations for typical use cases; feel free to use other values. Just keep in mind that using a block size less than the LZMA2 dictionary size is waste of RAM.

-

Set this to 0 to let liblzma choose the block size depending on the compression options. For LZMA2 it will be 3*dict_size or 1 MiB, whichever is more.

-

For each thread, about 3 * block_size bytes of memory will be allocated. This may change in later liblzma versions. If so, the memory usage will probably be reduced, not increased.

- -

-

- -

◆ timeout

- -

-

- - - - -

uint32_t lzma_mt::timeout

-

- -

Timeout to allow lzma_code() to return early.

-

Multithreading can make liblzma consume input and produce output in a very bursty way: it may first read a lot of input to fill internal buffers, then no input or output occurs for a while.

-

In single-threaded mode, lzma_code() won't return until it has either consumed all the input or filled the output buffer. If this is done in multithreaded mode, it may cause a call lzma_code() to take even tens of seconds, which isn't acceptable in all applications.

-

To avoid very long blocking times in lzma_code(), a timeout (in milliseconds) may be set here. If lzma_code() would block longer than this number of milliseconds, it will return with LZMA_OK. Reasonable values are 100 ms or more. The xz command line tool uses 300 ms.

-

If long blocking times are acceptable, set timeout to a special value of 0. This will disable the timeout mechanism and will make lzma_code() block until all the input is consumed or the output buffer has been filled.

-

Note: Even with a timeout, lzma_code() might sometimes take a long time to return. No timing guarantees are made.

- -

-

- -

◆ preset

- -

-

- - - - -

uint32_t lzma_mt::preset

-

- -

Encoder only: Compression preset.

-

The preset is set just like with lzma_easy_encoder(). The preset is ignored if filters below is non-NULL.

- -

-

- -

◆ filters

- -

-

- - - - -

const lzma_filter* lzma_mt::filters

-

- -

Encoder only: Filter chain (alternative to a preset)

-

If this is NULL, the preset above is used. Otherwise the preset is ignored and the filter chain specified here is used.

- -

-

- -

◆ check

- -

-

- - - - -

lzma_check lzma_mt::check

-

- -

Encoder only: Integrity check type.

-

See check.h for available checks. The xz command line tool defaults to LZMA_CHECK_CRC64, which is a good choice if you are unsure.

- -

-

- -

◆ memlimit_threading

- -

-

- - - - -

uint64_t lzma_mt::memlimit_threading

-

- -

Memory usage limit to reduce the number of threads.

-

Encoder: Ignored.

-

Decoder:

-

If the number of threads has been set so high that more than memlimit_threading bytes of memory would be needed, the number of threads will be reduced so that the memory usage will not exceed memlimit_threading bytes. However, if memlimit_threading cannot be met even in single-threaded mode, then decoding will continue in single-threaded mode and memlimit_threading may be exceeded even by a large amount. That is, memlimit_threading will never make lzma_code() return LZMA_MEMLIMIT_ERROR. To truly cap the memory usage, see memlimit_stop below.

-

Setting memlimit_threading to UINT64_MAX or a similar huge value means that liblzma is allowed to keep the whole compressed file and the whole uncompressed file in memory in addition to the memory needed by the decompressor data structures used by each thread! In other words, a reasonable value limit must be set here or it will cause problems sooner or later. If you have no idea what a reasonable value could be, try lzma_physmem() / 4 as a starting point. Setting this limit will never prevent decompression of a file; this will only reduce the number of threads.

-

If memlimit_threading is greater than memlimit_stop, then the value of memlimit_stop will be used for both.

- -

-

- -

◆ memlimit_stop

- -

-

- - - - -

uint64_t lzma_mt::memlimit_stop

-

- -

Memory usage limit that should never be exceeded.

-

Encoder: Ignored.

-

Decoder: If decompressing will need more than this amount of memory even in the single-threaded mode, then lzma_code() will return LZMA_MEMLIMIT_ERROR.

- -

-

The documentation for this struct was generated from the following file:

lzma/container.h

-

-Data Fields

Detailed Description

Field Documentation

◆ flags

◆ block_size

◆ timeout

◆ preset

◆ filters

◆ check

◆ memlimit_threading

◆ memlimit_stop