Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 100 insertions, 0 deletions

diff --git a/Documentation/hwmon/ltc2947.rst b/Documentation/hwmon/ltc2947.rst
new file mode 100644
index 000000000..419fc84fe
--- /dev/null
+++ b/Documentation/hwmon/ltc2947.rst
@@ -0,0 +1,100 @@
+Kernel drivers ltc2947-i2c and ltc2947-spi
+==========================================
+
+Supported chips:
+
+  * Analog Devices LTC2947
+
+    Prefix: 'ltc2947'
+
+    Addresses scanned: -
+
+    Datasheet:
+
+        https://www.analog.com/media/en/technical-documentation/data-sheets/LTC2947.pdf
+
+Author: Nuno Sá <nuno.sa@analog.com>
+
+Description
+___________
+
+The LTC2947 is a high precision power and energy monitor that measures current,
+voltage, power, temperature, charge and energy. The device supports both SPI
+and I2C depending on the chip configuration.
+The device also measures accumulated quantities as energy. It has two banks of
+register's to read/set energy related values. These banks can be configured
+independently to have setups like: energy1 accumulates always and enrgy2 only
+accumulates if current is positive (to check battery charging efficiency for
+example). The device also supports a GPIO pin that can be configured as output
+to control a fan as a function of measured temperature. Then, the GPIO becomes
+active as soon as a temperature reading is higher than a defined threshold. The
+temp2 channel is used to control this thresholds and to read the respective
+alarms.
+
+Sysfs entries
+_____________
+
+The following attributes are supported. Limits are read-write, reset_history
+is write-only and all the other attributes are read-only.
+
+======================= ==========================================
+in0_input		VP-VM voltage (mV).
+in0_min			Undervoltage threshold
+in0_max			Overvoltage threshold
+in0_lowest		Lowest measured voltage
+in0_highest		Highest measured voltage
+in0_reset_history	Write 1 to reset in1 history
+in0_min_alarm		Undervoltage alarm
+in0_max_alarm		Overvoltage alarm
+in0_label		Channel label (VP-VM)
+
+in1_input		DVCC voltage (mV)
+in1_min			Undervoltage threshold
+in1_max			Overvoltage threshold
+in1_lowest		Lowest measured voltage
+in1_highest		Highest measured voltage
+in1_reset_history	Write 1 to reset in2 history
+in1_min_alarm		Undervoltage alarm
+in1_max_alarm		Overvoltage alarm
+in1_label		Channel label (DVCC)
+
+curr1_input		IP-IM Sense current (mA)
+curr1_min		Undercurrent threshold
+curr1_max		Overcurrent threshold
+curr1_lowest		Lowest measured current
+curr1_highest		Highest measured current
+curr1_reset_history	Write 1 to reset curr1 history
+curr1_min_alarm		Undercurrent alarm
+curr1_max_alarm		Overcurrent alarm
+curr1_label		Channel label (IP-IM)
+
+power1_input		Power (in uW)
+power1_min		Low power threshold
+power1_max		High power threshold
+power1_input_lowest	Historical minimum power use
+power1_input_highest	Historical maximum power use
+power1_reset_history	Write 1 to reset power1 history
+power1_min_alarm	Low power alarm
+power1_max_alarm	High power alarm
+power1_label		Channel label (Power)
+
+temp1_input		Chip Temperature (in milliC)
+temp1_min		Low temperature threshold
+temp1_max		High temperature threshold
+temp1_input_lowest	Historical minimum temperature use
+temp1_input_highest	Historical maximum temperature use
+temp1_reset_history	Write 1 to reset temp1 history
+temp1_min_alarm		Low temperature alarm
+temp1_max_alarm		High temperature alarm
+temp1_label		Channel label (Ambient)
+
+temp2_min		Low temperature threshold for fan control
+temp2_max		High temperature threshold for fan control
+temp2_min_alarm		Low temperature fan control alarm
+temp2_max_alarm		High temperature fan control alarm
+temp2_label		Channel label (TEMPFAN)
+
+energy1_input		Measured energy over time (in microJoule)
+
+energy2_input		Measured energy over time (in microJoule)
+======================= ==========================================