Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 528 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/aspeed-bmc-tyan-s7106.dts b/arch/arm/boot/dts/aspeed-bmc-tyan-s7106.dts
new file mode 100644
index 000000000..aff27c1d4
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-tyan-s7106.dts
@@ -0,0 +1,528 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Tyan S7106 BMC";
+	compatible = "tyan,s7106-bmc", "aspeed,ast2500";
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200 earlycon";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		p2a_memory: region@987f0000 {
+			no-map;
+			reg = <0x987f0000 0x00010000>; /* 64KB */
+		};
+
+		vga_memory: framebuffer@9f000000 {
+			no-map;
+			reg = <0x9f000000 0x01000000>; /* 16M */
+		};
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>; /* 16M */
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		identify {
+			gpios = <&gpio ASPEED_GPIO(A, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		heartbeat {
+			gpios = <&gpio ASPEED_GPIO(E, 7) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+			<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
+			<&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>,
+			<&adc 12>, <&adc 13>, <&adc 14>;
+	};
+
+	iio-hwmon-battery {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 15>;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		label = "bmc";
+		status = "okay";
+		m25p,fast-read;
+#include "openbmc-flash-layout.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		label = "pnor";
+		m25p,fast-read;
+	};
+};
+
+&uart1 {
+	/* Rear RS-232 connector */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd1_default
+			&pinctrl_rxd1_default>;
+};
+
+&uart2 {
+	/* RS-232 connector on header */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd2_default
+			&pinctrl_rxd2_default>;
+};
+
+&uart3 {
+	/* Alternative to vuart to internally connect (route) to uart1
+	 * when vuart cannot be used due to BIOS limitations.
+	 */
+	status = "okay";
+};
+
+&uart4 {
+	/* Alternative to vuart to internally connect (route) to the
+	 * external port usually used by uart1 when vuart cannot be
+	 * used due to BIOS limitations.
+	 */
+	status = "okay";
+};
+
+&uart5 {
+	/* BMC "debug" (console) UART; connected to RS-232 connector
+	 * on header; selectable via jumpers as alternative to uart2
+	 */
+	status = "okay";
+};
+
+&uart_routing {
+	status = "okay";
+};
+
+&vuart {
+	status = "okay";
+
+	/* We enable the VUART here, but leave it in a state that does
+	 * not interfere with the SuperIO. The goal is to have both the
+	 * VUART and the SuperIO available and decide at runtime whether
+	 * the VUART should actually be used. For that reason, configure
+	 * an "invalid" IO address and an IRQ that is not used by the
+	 * BMC.
+	 */
+
+	aspeed,lpc-io-reg = <0xffff>;
+	aspeed,lpc-interrupts = <15 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lpc_ctrl {
+	status = "okay";
+};
+
+&p2a {
+	status = "okay";
+	memory-region = <&p2a_memory>;
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>;
+};
+
+&adc {
+	status = "okay";
+};
+
+&vhub {
+	status = "okay";
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default
+			&pinctrl_pwm1_default
+			&pinctrl_pwm3_default
+			&pinctrl_pwm4_default>;
+
+	/* CPU fan #0 */
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00>;
+	};
+
+	/* CPU fan #1 */
+	fan@1 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x01>;
+	};
+
+	/* PWM group for chassis fans #1, #2, #3 and #4  */
+	fan@2 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02>;
+	};
+
+	fan@3 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x03>;
+	};
+
+	fan@4 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04>;
+	};
+
+	fan@5 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x05>;
+	};
+
+	/* PWM group for chassis fans #5 and #6  */
+	fan@6 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x06>;
+	};
+
+	fan@7 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x07>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	/* Hardware monitor with temperature sensors */
+	nct7802@28 {
+		compatible = "nuvoton,nct7802";
+		reg = <0x28>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@0 { /* LTD */
+			reg = <0>;
+		};
+
+		channel@1 { /* RTD1 */
+			reg = <1>;
+			sensor-type = "temperature";
+			temperature-mode = "thermistor";
+		};
+
+		channel@2 { /* RTD2 */
+			reg = <2>;
+			sensor-type = "temperature";
+			temperature-mode = "thermistor";
+		};
+
+		channel@3 { /* RTD3 */
+			reg = <3>;
+			sensor-type = "temperature";
+		};
+	};
+
+	/* Also connected to:
+	 * - IPMB pin header
+	 * - CPU #0 memory error LED @ 0x3A
+	 * - CPU #1 memory error LED @ 0x3C
+	 */
+};
+
+&i2c1 {
+	/* Directly connected to PCH SMBUS #0 */
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+
+	/* BMC EEPROM, incl. mainboard FRU */
+	eeprom@50 {
+		compatible = "atmel,24c256";
+		reg = <0x50>;
+	};
+
+	/* Also connected to:
+	 * - fan header
+	 * - mini-SAS HD connector
+	 * - SSATA SGPIO
+	 * - via switch (BMC_SMB3_PCH_IE_SML3_EN, active low)
+	 *   to PCH SMBUS #3
+	 */
+};
+
+&i2c3 {
+	status = "okay";
+
+	/* PSU1 FRU @ 0xA0 */
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+	};
+
+	/* PSU2 FRU @ 0xA2 */
+	eeprom@51 {
+		compatible = "atmel,24c02";
+		reg = <0x51>;
+	};
+
+	/* PSU1 @ 0xB0 */
+	power-supply@58 {
+		compatible = "pmbus";
+		reg = <0x58>;
+	};
+
+	/* PSU2 @ 0xB2 */
+	power-supply@59 {
+		compatible = "pmbus";
+		reg = <0x59>;
+	};
+
+	/* Also connected to:
+	 * - PCH SMBUS #1
+	 */
+};
+
+&i2c4 {
+	status = "okay";
+
+	/* Connected to:
+	 * - PCH SMBUS #2
+	 */
+
+	/* Connected via switch to:
+	 * - CPU #0 channels ABC VDDQ @ 0x80
+	 * - CPU #0 channels DEF VDDQ @ 0x81
+	 * - CPU #1 channels ABC VDDQ @ 0x82
+	 * - CPU #1 channels DEF VDDQ @ 0x83
+	 * - CPU #0 VCCIO & VMCP @ 0x52
+	 * - CPU #1 VCCIO & VMCP @ 0x53
+	 * - CPU #0 VCCIN @ 0xC0
+	 * - CPU #0 VSA @ 0xC2
+	 * - CPU #1 VCCIN @ 0xC4
+	 * - CPU #1 VSA @ 0xC6
+	 * - J110
+	 */
+};
+
+&i2c5 {
+	status = "okay";
+
+	/* Connected via switch (PCH_BMC_SMB_SW_P) to:
+	 * - mainboard FRU @ 0xAE
+	 * - XDP connector
+	 * - ME debug header
+	 * - clock buffer @ 0xD8
+	 * - i2c4 via switch (PCH_VR_SMBUS_SW_P; controlled by PCH)
+	 * - PCH SMBUS
+	 */
+};
+
+&i2c6 {
+	status = "okay";
+
+	/* Connected via switch (BMC_PE_SMB_EN_1_N) to
+	 * bus mux (selector BMC_PE_SMB_SW_BIT[1..0]) to:
+	 * - 0,0: PCIE slot 1, SMB #1
+	 * - 0,1: PCIE slot 1, SMB #2
+	 * - 1,0: PCIE slot 2, SMB #1
+	 * - 1,1: PCIE slot 2, SMB #2
+	 */
+
+	/* Connected via switch (BMC_PE_SMB_EN_2_N) to
+	 * bus mux (selector BMC_PE_SMB_SW_BIT[1..0]) to:
+	 * - 0,0: OCP0 (A) SMB
+	 * - 0,1: OCP0 (C) SMB
+	 * - 1,0: OCP1 (A) SMB
+	 * - 1,1: NC
+	 */
+};
+
+&i2c7 {
+	status = "okay";
+
+	/* Connected to:
+	 * - PCH SMBUS #4
+	 */
+};
+
+&i2c8 {
+	status = "okay";
+
+	/* Not connected */
+};
+
+&mac0 {
+	status = "okay";
+	use-ncsi;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii1_default>;
+};
+
+&mac1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
+};
+
+&ibt {
+	status = "okay";
+};
+
+&kcs1 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+};
+
+/* Enable BMC VGA output to show an early (pre-BIOS) boot screen */
+&gfx {
+	status = "okay";
+	memory-region = <&gfx_memory>;
+};
+
+/* We're following the GPIO naming as defined at
+ * https://github.com/openbmc/docs/blob/master/designs/device-tree-gpio-naming.md.
+ *
+ * Notes on led-identify and id-button:
+ * - A physical button is connected to id-button which
+ *   triggers the clock on a D flip-flop. The /Q output of the
+ *   flip-flop drives its D input.
+ * - The flip-flop's Q output drives led-identify which is
+ *   connected to LEDs.
+ * - With that, every button press toggles the LED between on and off.
+ *
+ * Notes on power-, reset- and nmi- button and control:
+ * - The -button signals can be used to monitor physical buttons.
+ * - The -control signals can be used to actuate the specific
+ *   operation.
+ * - In hardware, the -button signals are connected to the -control
+ *   signals through drivers with the -control signals being
+ *   protected through diodes.
+ */
+&gpio {
+	status = "okay";
+	gpio-line-names =
+	/*A0*/		"",
+	/*A1*/		"",
+	/*A2*/		"led-identify", /* in/out: BMC_IDLED_ON_N */
+	/*A3*/		"",
+	/*A4*/		"",
+	/*A5*/		"",
+	/*A6*/		"",
+	/*A7*/		"",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0*/		"",
+	/*C1*/		"",
+	/*C2*/		"",
+	/*C3*/		"",
+	/*C4*/		"id-button", /* in/out: BMC_IDBTN_IN_OUT_N */
+	/*C5*/		"post-complete", /* in: FM_BIOS_POST_CMPLT_N */
+	/*C6*/		"",
+	/*C7*/		"",
+	/*D0*/		"",
+	/*D1*/		"",
+	/*D2*/		"power-chassis-good", /* in: SYS_PWROK_BUF */
+	/*D3*/		"platform-reset", /* in: SYS_PLTRST_N */
+	/*D4*/		"",
+	/*D5*/		"",
+	/*D6*/		"",
+	/*D7*/		"",
+	/*E0*/		"power-button", /* in: BMC_PWBTN_IN_N */
+	/*E1*/		"power-chassis-control", /* out: BMC_PWRBTN_OUT_N */
+	/*E2*/		"reset-button", /* in: BMC_RSTBTN_IN_N */
+	/*E3*/		"reset-control", /* out: BMC_RSTBTN_OUT_N */
+	/*E4*/		"nmi-button", /* in: BMC_NMIBTN_IN_N */
+	/*E5*/		"nmi-control", /* out: BMC_NMIBTN_OUT_N */
+	/*E6*/		"",
+	/*E7*/		"led-heartbeat", /* out: BMC_HEARTBRAT_LED_N */
+	/*F0*/		"",
+	/*F1*/		"clear-cmos-control", /* out: BMC_CLR_CMOS_N */
+	/*F2*/		"",
+	/*F3*/		"",
+	/*F4*/		"led-fault", /* out: AST_HW_FAULT_N */
+	/*F5*/		"",
+	/*F6*/		"",
+	/*F7*/		"",
+	/*G0*/		"BMC_PE_SMB_EN_1_N", /* out */
+	/*G1*/		"BMC_PE_SMB_EN_2_N", /* out */
+	/*G2*/		"",
+	/*G3*/		"",
+	/*G4*/		"",
+	/*G5*/		"",
+	/*G6*/		"",
+	/*G7*/		"",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0*/		"",
+	/*Q1*/		"",
+	/*Q2*/		"",
+	/*Q3*/		"",
+	/*Q4*/		"BMC_PE_SMB_SW_BIT0", /* out */
+	/*Q5*/		"BMC_PE_SMB_SW_BIT1", /* out */
+	/*Q6*/		"",
+	/*Q7*/		"",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","",
+	/*AA0*/		"",
+	/*AA1*/		"",
+	/*AA2*/		"",
+	/*AA3*/		"BMC_SMB3_PCH_IE_SML3_EN", /* out */
+	/*AA4*/		"",
+	/*AA5*/		"",
+	/*AA6*/		"",
+	/*AA7*/		"",
+	/*AB0-AB7*/	"","","","","","","","";
+};