Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 174 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/intel-ixp42x-gateworks-gw2348.dts b/arch/arm/boot/dts/intel-ixp42x-gateworks-gw2348.dts
new file mode 100644
index 000000000..a5943f51e
--- /dev/null
+++ b/arch/arm/boot/dts/intel-ixp42x-gateworks-gw2348.dts
@@ -0,0 +1,174 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the Gateworks Avila GW2348 board.
+ * This machine is based on IXP425.
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Gateworks Avila GW2348";
+	compatible = "gateworks,gw2348", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x4000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = "uart0:115200n8";
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-user {
+			label = "gw2348:green:user";
+			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	i2c {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hwmon@28 {
+			compatible = "adi,ad7418";
+			reg = <0x28>;
+		};
+		rtc: ds1672@68 {
+			compatible = "dallas,ds1672";
+			reg = <0x68>;
+		};
+		eeprom@51 {
+			compatible = "atmel,24c08";
+			reg = <0x51>;
+			pagesize = <16>;
+			size = <1024>;
+			read-only;
+		};
+	};
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/* Enable writes on the expansion bus */
+				intel,ixp4xx-eb-write-enable = <1>;
+				/* 16 MB of Flash mapped in at CS0 */
+				reg = <0 0x00000000 0x1000000>;
+
+				partitions {
+					compatible = "redboot-fis";
+					/* Eraseblock at 0x0fe0000 */
+					fis-index-block = <0x7f>;
+				};
+			};
+			ide@1,0 {
+				compatible = "intel,ixp4xx-compact-flash";
+				/*
+				 * Set up expansion bus config to a really slow timing.
+				 * The CF driver will dynamically reconfigure these timings
+				 * depending on selected PIO mode (0-4).
+				 */
+				intel,ixp4xx-eb-t1 = <3>; // 3 cycles extra address phase
+				intel,ixp4xx-eb-t2 = <3>; // 3 cycles extra setup phase
+				intel,ixp4xx-eb-t3 = <15>; // 15 cycles extra strobe phase
+				intel,ixp4xx-eb-t4 = <3>; // 3 cycles extra hold phase
+				intel,ixp4xx-eb-t5 = <15>; // 15 cycles extra recovery phase
+				intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle type
+				intel,ixp4xx-eb-byte-access-on-halfword = <1>;
+				intel,ixp4xx-eb-mux-address-and-data = <0>;
+				intel,ixp4xx-eb-ahb-split-transfers = <0>;
+				intel,ixp4xx-eb-write-enable = <1>;
+				intel,ixp4xx-eb-byte-access = <1>;
+				/* First register set is CMD second is CTL (notice it uses CS2) */
+				reg = <1 0x00000000 0x1000000>, <2 0x00000000 0x1000000>;
+				interrupt-parent = <&gpio0>;
+				interrupts = <12 IRQ_TYPE_EDGE_RISING>;
+			};
+			/*
+			 * FIXME: Latch LEDs or extra UARTs at CS4
+			 */
+		};
+
+		pci@c0000000 {
+			status = "ok";
+
+			/*
+			 * Taken from Avila PCI boardfile.
+			 *
+			 * We have up to 4 slots (IDSEL) with 4 swizzled IRQs.
+			 */
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+			/* IDSEL 1 */
+			<0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */
+			<0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */
+			<0x0800 0 0 3 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */
+			<0x0800 0 0 4 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */
+			/* IDSEL 2 */
+			<0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */
+			<0x1000 0 0 2 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */
+			<0x1000 0 0 3 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 8 */
+			<0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 11 */
+			/* IDSEL 3 */
+			<0x1800 0 0 1 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */
+			<0x1800 0 0 2 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */
+			<0x1800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 11 */
+			<0x1800 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 10 */
+			/* IDSEL 4 */
+			<0x2000 0 0 1 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 4 is irq 8 */
+			<0x2000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 4 is irq 11 */
+			<0x2000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 4 is irq 10 */
+			<0x2000 0 0 4 &gpio0 9  IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 4 is irq 9 */
+		};
+
+		/* EthB */
+		ethernet@c8009000 {
+			status = "ok";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy0>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+			};
+		};
+
+		/* EthC */
+		ethernet@c800a000 {
+			status = "ok";
+			queue-rx = <&qmgr 4>;
+			queue-txready = <&qmgr 21>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy1>;
+		};
+	};
+};