Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 377 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
new file mode 100644
index 000000000..e66fa59c2
--- /dev/null
+++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
@@ -0,0 +1,377 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 ST-Ericsson AB
+ */
+
+#include "ste-href-ab8500.dtsi"
+#include "ste-href.dtsi"
+
+/ {
+	model = "ST-Ericsson HREF (v60+) platform with Device Tree";
+	compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
+
+	thermal-zones {
+		chassis-thermal {
+			/* Poll every 20 seconds */
+			polling-delay = <20000>;
+			/* Poll every 2nd second when cooling */
+			polling-delay-passive = <2000>;
+
+			thermal-sensors = <&therm1>, <&therm2>;
+
+			/* Tripping points made from rough guess about operating conditions */
+			trips {
+				chassis_alert: chassis-alert {
+					/* At 50 degrees take down the CPU frequency */
+					temperature = <50000>;
+					hysteresis = <3000>;
+					type = "active";
+				};
+				chassis_crit: chassis-crit {
+					/* Just shut down at 70 degrees */
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			/* Push down the operating frequency of the SoC when it gets hot */
+			cooling-maps {
+				map0 {
+					trip = <&chassis_alert>;
+					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+					contribution = <100>;
+				};
+			};
+		};
+	};
+
+	/*
+	 * Thermistors on the board, formally to monitor battery temperatures
+	 * but what they measure is the board temperature.
+	 */
+	therm1: thermistor@0 {
+		compatible = "murata,ncp18wb473";
+		io-channels = <&gpadc 0x06>; /* AUX1 */
+		pullup-uv = <1800000>;
+		pullup-ohm = <220000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	therm2: thermistor@1 {
+		compatible = "murata,ncp18wb473";
+		io-channels = <&gpadc 0x07>; /* AUX2 */
+		pullup-uv = <1800000>;
+		pullup-ohm = <220000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	soc {
+		/* Name the GPIO muxed rails on the HREF boards */
+		gpio@8012e000 {
+			/* GPIOs 0 - 31 */
+			gpio-line-names =
+				     /* GPIO0,1 used for UART0 BT RX/TX */
+				     "", "",
+				     "UART_WAKE",
+				     "BT_WAKE",
+				     "",
+				     "SDMMC_1V8_3V_SEL",
+				     "FLASH_LED_SYNC (FLASH_CTRL_0)",
+				     "XENON_READY (FLASH_CTRL_1)",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "",
+				     "",
+				     "FLASH_LED_EN (FLASH_CTRL_3)",
+				     "", "",
+				     "", "", "", "", "",
+				     /* Used by UART2 (console) */
+				     "", "",
+				     "MAGNETOMETER_INT";
+		};
+
+		gpio@8012e080 {
+			/* GPIOs 32 - 63 */
+			gpio-line-names =
+				     "MAGNETOMETER_DRDY",
+				     "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "";
+		};
+
+		gpio@8000e000 {
+			/* GPIOs 64 - 95 */
+			gpio-line-names = "XENON_EN2 (FLASH_CTRL_4)",
+				     "DISP1_RST",
+				     "DISP2_RST",
+				     "TOUCH_INT2",
+				     "LCD_VSI0_A",
+				     "LCD_VSI1_A",
+				     /* GPIO 70-77 used for ETM */
+				     "", "", "", "", "", "", "", "",
+				     /* GPIO 78-81 used for YCBCR */
+				     "", "", "", "",
+				     "ACCELEROMETER_INT1_RDY",
+				     "ACCELEROMETER_INT2",
+				     "TOUCH_INT",
+				     "WLAN_ENA",
+				     "", "", "", "", "",
+				     "FORCE_SENSING_INT",
+				     "FORCE_SENSING_RESET",
+				     "", "",
+				     "SDMMC_CD";
+		};
+
+		gpio@8000e080 {
+			/* GPIOs 96 - 127 */
+			gpio-line-names = "",
+				     "FORCE_SENSING_WU",
+				     "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "";
+		};
+
+		gpio@8000e100 {
+			/* GPIOs 128 - 159 */
+			gpio-line-names = "", "", "", "", "", "", "", "",
+				     "", "", "",
+				     "DIPRO_INT", /* GPIO139 */
+				     "XSHUTDOWN_SECONDARY_SENSOR",
+				     "XSHUTDOWN_PRIMARY_SENSOR",
+				     "NFC_RST (NFC_CTRL_",
+				     "TOUCH_RST",
+				     "NFC_IRQ (NFC_CTRL_1)",
+				     "HAL_SW",
+				     "TOUCH_RST2",
+				     "", "",
+				     "VAUDIO_HF_EN", /* GPIO149 */
+				     "", "", "", "", "", "", "", "", "", "";
+		};
+
+		gpio@8000e180 {
+			/* GPIOs 160 - 191 */
+			gpio-line-names = "", "", "", "", "", "", "", "",
+				     "",
+				     "SDMMC_EN",
+				     "XENON_CHARGE (FLASH_CONTROL_5)",
+				     "GBF_ENA_RESET",
+				     "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "";
+		};
+
+		gpio@8011e000 {
+			/* GPIOs 192 - 223 */
+			gpio-line-names = "HDTV_INTN",
+				     "", "", "",
+				     "HDTV_RSTN",
+				     "", "", "",
+				     "", /* GPIO200 */
+				     "", "", "", "", "", "", "",
+				     /* GPIO208-216 used for WGBF_MC1 */
+				     "", "", "", "", "", "", "", "", "",
+				     "SW_FRONT_PROXIMITY", /* GPIO217 */
+				     "KPD_CTRL_INT", /* Keypad controller */
+				     "", "", "", "", "";
+		};
+
+		gpio@8011e080 {
+			/* GPIOs 224 - 255 */
+			gpio-line-names = "", "",
+				     "HSIT_ACWAKE0",
+				     "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "";
+		};
+
+		// External Micro SD slot
+		mmc@80126000 {
+			cd-gpios  = <&gpio2 31 GPIO_ACTIVE_HIGH>; // 95
+		};
+
+		pinctrl {
+			/*
+			 * Set this up using hogs, as time goes by and as seems fit, these
+			 * can be moved over to being controlled by respective device.
+			 */
+			pinctrl-names = "default";
+			pinctrl-0 = <&ipgpio_hrefv60_mode>,
+				  <&etm_hrefv60_mode>,
+				  <&nahj_hrefv60_mode>,
+				  <&nfc_hrefv60_mode>,
+				  <&force_hrefv60_mode>,
+				  <&dipro_hrefv60_mode>,
+				  <&vaudio_hf_hrefv60_mode>,
+				  <&gbf_hrefv60_mode>,
+				  <&hdtv_hrefv60_mode>,
+				  <&gpios_hrefv60_mode>;
+
+			sdi0 {
+				sdi0_default_mode: sdi0_default {
+					/* SD card detect GPIO pin, extend default state */
+					default_hrefv60_cfg1 {
+						pins = "GPIO95_E8";
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+			ipgpio {
+				/*
+				 * XENON Flashgun on image processor GPIO (controlled from image
+				 * processor firmware), mux in these image processor GPIO lines 0
+				 * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant
+				 * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias
+				 * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output.
+				 */
+				ipgpio_hrefv60_mode: ipgpio_hrefv60 {
+					hrefv60_mux {
+						function = "ipgpio";
+						groups = "ipgpio0_c_1", "ipgpio1_c_1", "ipgpio4_c_1";
+					};
+					hrefv60_cfg1 {
+						pins = "GPIO6_AF6", "GPIO7_AG5";
+						ste,config = <&in_pu>;
+					};
+					hrefv60_cfg2 {
+						pins = "GPIO21_AB3";
+						ste,config = <&gpio_out_lo>;
+					};
+					hrefv60_cfg3 {
+						pins = "GPIO64_F3";
+						ste,config = <&out_lo>;
+					};
+				};
+			};
+			etm {
+				/*
+				 * Drive D19-D23 for the ETM PTM trace interface low,
+				 * (presumably pins are unconnected therefore grounded here,
+				 * the "other alt C1" setting enables these pins)
+				 */
+				etm_hrefv60_mode: etm_hrefv60 {
+					hrefv60_cfg1 {
+						pins =
+						"GPIO70_G5",
+						"GPIO71_G4",
+						"GPIO72_H4",
+						"GPIO73_H3",
+						"GPIO74_J3";
+						ste,config = <&gpio_out_lo>;
+					};
+				 };
+			};
+			nahj {
+				nahj_hrefv60_mode: nahj_hrefv60 {
+					/* NAHJ CTRL on GPIO76 to low, CTRL_INV on GPIO216 to high */
+					hrefv60_cfg1 {
+						pins = "GPIO76_J2";
+						ste,config = <&gpio_out_lo>;
+					};
+					hrefv60_cfg2 {
+						pins = "GPIO216_AG12";
+						ste,config = <&gpio_out_hi>;
+					};
+				 };
+			};
+			nfc {
+				nfc_hrefv60_mode: nfc_hrefv60 {
+					/* NFC ENA and RESET to low, pulldown IRQ line */
+					hrefv60_cfg1 {
+						pins =
+						"GPIO77_H1", /* NFC_ENA */
+						"GPIO142_C11"; /* NFC_RESET */
+						ste,config = <&gpio_out_lo>;
+					};
+					hrefv60_cfg2 {
+						pins = "GPIO144_B13"; /* NFC_IRQ */
+						ste,config = <&gpio_in_pd>;
+					};
+				 };
+			};
+			force {
+				force_hrefv60_mode: force_hrefv60 {
+					hrefv60_cfg1 {
+						pins = "GPIO91_B6"; /* FORCE_SENSING_INT */
+						ste,config = <&gpio_in_pu>;
+					};
+					hrefv60_cfg2 {
+						pins =
+						"GPIO92_D6", /* FORCE_SENSING_RST */
+						"GPIO97_D9"; /* FORCE_SENSING_WU */
+						ste,config = <&gpio_out_lo>;
+					};
+				 };
+			};
+			dipro {
+				dipro_hrefv60_mode: dipro_hrefv60 {
+					hrefv60_cfg1 {
+						pins = "GPIO139_C9"; /* DIPRO_INT */
+						ste,config = <&gpio_in_pu>;
+					};
+				 };
+			};
+			vaudio_hf {
+				vaudio_hf_hrefv60_mode: vaudio_hf_hrefv60 {
+					/* Audio Amplifier HF enable GPIO */
+					hrefv60_cfg1 {
+						pins = "GPIO149_B14"; /* VAUDIO_HF_EN, enable MAX8968 */
+						ste,config = <&gpio_out_hi>;
+					};
+				 };
+			};
+			gbf {
+				gbf_hrefv60_mode: gbf_hrefv60 {
+					/*
+					 * GBF (GPS, Bluetooth, FM-radio) interface,
+					 * pull low to reset state
+					 */
+					hrefv60_cfg1 {
+						pins = "GPIO171_D23"; /* GBF_ENA_RESET */
+						ste,config = <&gpio_out_lo>;
+					};
+				 };
+			};
+			hdtv {
+				hdtv_hrefv60_mode: hdtv_hrefv60 {
+					/* MSP : HDTV INTERFACE GPIO line */
+					hrefv60_cfg1 {
+						pins = "GPIO192_AJ27";
+						ste,config = <&gpio_in_pd>;
+					};
+				 };
+			};
+			mcde {
+				lcd_hrefv60_mode: lcd_hrefv60 {
+					/*
+					 * Display Interface 1 uses GPIO 65 for RST (reset).
+					 * Display Interface 2 uses GPIO 66 for RST (reset).
+					 * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset)
+					 */
+					hrefv60_cfg1 {
+						pins = "GPIO65_F1";
+						ste,config = <&gpio_out_hi>;
+					};
+					hrefv60_cfg2 {
+						pins = "GPIO66_G3";
+						ste,config = <&gpio_out_lo>;
+					};
+				};
+			};
+			gpios {
+				/* Dangling GPIO pins */
+				gpios_hrefv60_mode: gpios_hrefv60 {
+					default_cfg1 {
+						/* Normally UART1 RXD, now dangling */
+						pins = "GPIO4_AH6";
+						ste,config = <&in_pu>;
+					};
+				};
+			};
+		};
+	};
+};