Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 140 insertions, 0 deletions

diff --git a/arch/arm64/boot/dts/qcom/pms405.dtsi b/arch/arm64/boot/dts/qcom/pms405.dtsi
new file mode 100644
index 000000000..634b0681d
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pms405.dtsi
@@ -0,0 +1,140 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2018, Linaro Limited
+
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	thermal-zones {
+		pms405-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&pms405_temp>;
+
+			trips {
+				pms405_alert0: pms405-alert0 {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				pms405_crit: pms405-crit {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+	pms405_0: pms405@0 {
+		compatible = "qcom,pms405", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pms405_gpios: gpio@c000 {
+			compatible = "qcom,pms405-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			gpio-ranges = <&pms405_gpios 0 0 12>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pon@800 {
+			compatible = "qcom,pms405-pon";
+			reg = <0x0800>;
+			mode-bootloader = <0x2>;
+			mode-recovery = <0x1>;
+
+			pwrkey {
+				compatible = "qcom,pm8941-pwrkey";
+				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				linux,code = <KEY_POWER>;
+			};
+		};
+
+		pms405_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
+			io-channels = <&pms405_adc ADC5_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pms405_adc: adc@3100 {
+			compatible = "qcom,pms405-adc", "qcom,spmi-adc-rev2";
+			reg = <0x3100>;
+			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+
+			ref_gnd@0 {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+			};
+
+			vref_1p25@1 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+			};
+
+			pon_1: vph_pwr@131 {
+				reg = <ADC5_VPH_PWR>;
+				qcom,pre-scaling = <1 3>;
+			};
+
+			die_temp@6 {
+				reg = <ADC5_DIE_TEMP>;
+				qcom,pre-scaling = <1 1>;
+			};
+
+			pa_therm1: thermistor1@77 {
+				reg = <ADC5_AMUX_THM1_100K_PU>;
+				qcom,ratiometric;
+				qcom,hw-settle-time = <200>;
+				qcom,pre-scaling = <1 1>;
+			};
+
+			pa_therm3: thermistor3@79 {
+				reg = <ADC5_AMUX_THM3_100K_PU>;
+				qcom,ratiometric;
+				qcom,hw-settle-time = <200>;
+				qcom,pre-scaling = <1 1>;
+			};
+
+			xo_therm: xo_temp@76 {
+				reg = <ADC5_XO_THERM_100K_PU>;
+				qcom,ratiometric;
+				qcom,hw-settle-time = <200>;
+				qcom,pre-scaling = <1 1>;
+			};
+		};
+
+		rtc@6000 {
+			compatible = "qcom,pm8941-rtc";
+			reg = <0x6000>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
+		};
+	};
+
+	pms405_1: pms405@1 {
+		compatible = "qcom,pms405", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+
+		pms405_spmi_regulators: regulators {
+			compatible = "qcom,pms405-regulators";
+		};
+	};
+};