Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 466 insertions, 0 deletions

diff --git a/drivers/input/touchscreen/wm9712.c b/drivers/input/touchscreen/wm9712.c
new file mode 100644
index 000000000..6947714df
--- /dev/null
+++ b/drivers/input/touchscreen/wm9712.c
@@ -0,0 +1,466 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * wm9712.c  --  Codec driver for Wolfson WM9712 AC97 Codecs.
+ *
+ * Copyright 2003, 2004, 2005, 2006, 2007 Wolfson Microelectronics PLC.
+ * Author: Liam Girdwood <lrg@slimlogic.co.uk>
+ * Parts Copyright : Ian Molton <spyro@f2s.com>
+ *                   Andrew Zabolotny <zap@homelink.ru>
+ *                   Russell King <rmk@arm.linux.org.uk>
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/kernel.h>
+#include <linux/input.h>
+#include <linux/delay.h>
+#include <linux/bitops.h>
+#include <linux/wm97xx.h>
+
+#define TS_NAME			"wm97xx"
+#define WM9712_VERSION		"1.00"
+#define DEFAULT_PRESSURE	0xb0c0
+
+/*
+ * Module parameters
+ */
+
+/*
+ * Set internal pull up for pen detect.
+ *
+ * Pull up is in the range 1.02k (least sensitive) to 64k (most sensitive)
+ * i.e. pull up resistance = 64k Ohms / rpu.
+ *
+ * Adjust this value if you are having problems with pen detect not
+ * detecting any down event.
+ */
+static int rpu = 8;
+module_param(rpu, int, 0);
+MODULE_PARM_DESC(rpu, "Set internal pull up resistor for pen detect.");
+
+/*
+ * Set current used for pressure measurement.
+ *
+ * Set pil = 2 to use 400uA
+ *     pil = 1 to use 200uA and
+ *     pil = 0 to disable pressure measurement.
+ *
+ * This is used to increase the range of values returned by the adc
+ * when measureing touchpanel pressure.
+ */
+static int pil;
+module_param(pil, int, 0);
+MODULE_PARM_DESC(pil, "Set current used for pressure measurement.");
+
+/*
+ * Set threshold for pressure measurement.
+ *
+ * Pen down pressure below threshold is ignored.
+ */
+static int pressure = DEFAULT_PRESSURE & 0xfff;
+module_param(pressure, int, 0);
+MODULE_PARM_DESC(pressure, "Set threshold for pressure measurement.");
+
+/*
+ * Set adc sample delay.
+ *
+ * For accurate touchpanel measurements, some settling time may be
+ * required between the switch matrix applying a voltage across the
+ * touchpanel plate and the ADC sampling the signal.
+ *
+ * This delay can be set by setting delay = n, where n is the array
+ * position of the delay in the array delay_table below.
+ * Long delays > 1ms are supported for completeness, but are not
+ * recommended.
+ */
+static int delay = 3;
+module_param(delay, int, 0);
+MODULE_PARM_DESC(delay, "Set adc sample delay.");
+
+/*
+ * Set five_wire = 1 to use a 5 wire touchscreen.
+ *
+ * NOTE: Five wire mode does not allow for readback of pressure.
+ */
+static int five_wire;
+module_param(five_wire, int, 0);
+MODULE_PARM_DESC(five_wire, "Set to '1' to use 5-wire touchscreen.");
+
+/*
+ * Set adc mask function.
+ *
+ * Sources of glitch noise, such as signals driving an LCD display, may feed
+ * through to the touch screen plates and affect measurement accuracy. In
+ * order to minimise this, a signal may be applied to the MASK pin to delay or
+ * synchronise the sampling.
+ *
+ * 0 = No delay or sync
+ * 1 = High on pin stops conversions
+ * 2 = Edge triggered, edge on pin delays conversion by delay param (above)
+ * 3 = Edge triggered, edge on pin starts conversion after delay param
+ */
+static int mask;
+module_param(mask, int, 0);
+MODULE_PARM_DESC(mask, "Set adc mask function.");
+
+/*
+ * Coordinate Polling Enable.
+ *
+ * Set to 1 to enable coordinate polling. e.g. x,y[,p] is sampled together
+ * for every poll.
+ */
+static int coord;
+module_param(coord, int, 0);
+MODULE_PARM_DESC(coord, "Polling coordinate mode");
+
+/*
+ * ADC sample delay times in uS
+ */
+static const int delay_table[] = {
+	21,    /* 1 AC97 Link frames */
+	42,    /* 2 */
+	84,    /* 4 */
+	167,   /* 8 */
+	333,   /* 16 */
+	667,   /* 32 */
+	1000,  /* 48 */
+	1333,  /* 64 */
+	2000,  /* 96 */
+	2667,  /* 128 */
+	3333,  /* 160 */
+	4000,  /* 192 */
+	4667,  /* 224 */
+	5333,  /* 256 */
+	6000,  /* 288 */
+	0      /* No delay, switch matrix always on */
+};
+
+/*
+ * Delay after issuing a POLL command.
+ *
+ * The delay is 3 AC97 link frames + the touchpanel settling delay
+ */
+static inline void poll_delay(int d)
+{
+	udelay(3 * AC97_LINK_FRAME + delay_table[d]);
+}
+
+/*
+ * set up the physical settings of the WM9712
+ */
+static void wm9712_phy_init(struct wm97xx *wm)
+{
+	u16 dig1 = 0;
+	u16 dig2 = WM97XX_RPR | WM9712_RPU(1);
+
+	/* WM9712 rpu */
+	if (rpu) {
+		dig2 &= 0xffc0;
+		dig2 |= WM9712_RPU(rpu);
+		dev_dbg(wm->dev, "setting pen detect pull-up to %d Ohms\n",
+			64000 / rpu);
+	}
+
+	/* WM9712 five wire */
+	if (five_wire) {
+		dig2 |= WM9712_45W;
+		dev_dbg(wm->dev, "setting 5-wire touchscreen mode.\n");
+
+		if (pil) {
+			dev_warn(wm->dev, "pressure measurement is not "
+				 "supported in 5-wire mode\n");
+			pil = 0;
+		}
+	}
+
+	/* touchpanel pressure current*/
+	if (pil == 2) {
+		dig2 |= WM9712_PIL;
+		dev_dbg(wm->dev,
+			"setting pressure measurement current to 400uA.\n");
+	} else if (pil)
+		dev_dbg(wm->dev,
+			"setting pressure measurement current to 200uA.\n");
+	if (!pil)
+		pressure = 0;
+
+	/* polling mode sample settling delay */
+	if (delay < 0 || delay > 15) {
+		dev_dbg(wm->dev, "supplied delay out of range.\n");
+		delay = 4;
+	}
+	dig1 &= 0xff0f;
+	dig1 |= WM97XX_DELAY(delay);
+	dev_dbg(wm->dev, "setting adc sample delay to %d u Secs.\n",
+		delay_table[delay]);
+
+	/* mask */
+	dig2 |= ((mask & 0x3) << 6);
+	if (mask) {
+		u16 reg;
+		/* Set GPIO4 as Mask Pin*/
+		reg = wm97xx_reg_read(wm, AC97_MISC_AFE);
+		wm97xx_reg_write(wm, AC97_MISC_AFE, reg | WM97XX_GPIO_4);
+		reg = wm97xx_reg_read(wm, AC97_GPIO_CFG);
+		wm97xx_reg_write(wm, AC97_GPIO_CFG, reg | WM97XX_GPIO_4);
+	}
+
+	/* wait - coord mode */
+	if (coord)
+		dig2 |= WM9712_WAIT;
+
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, dig1);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, dig2);
+}
+
+static void wm9712_dig_enable(struct wm97xx *wm, int enable)
+{
+	u16 dig2 = wm->dig[2];
+
+	if (enable) {
+		wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2,
+				 dig2 | WM97XX_PRP_DET_DIG);
+		wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD); /* dummy read */
+	} else
+		wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2,
+				 dig2 & ~WM97XX_PRP_DET_DIG);
+}
+
+static void wm9712_aux_prepare(struct wm97xx *wm)
+{
+	memcpy(wm->dig_save, wm->dig, sizeof(wm->dig));
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, 0);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, WM97XX_PRP_DET_DIG);
+}
+
+static void wm9712_dig_restore(struct wm97xx *wm)
+{
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, wm->dig_save[1]);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, wm->dig_save[2]);
+}
+
+static inline int is_pden(struct wm97xx *wm)
+{
+	return wm->dig[2] & WM9712_PDEN;
+}
+
+/*
+ * Read a sample from the WM9712 adc in polling mode.
+ */
+static int wm9712_poll_sample(struct wm97xx *wm, int adcsel, int *sample)
+{
+	int timeout = 5 * delay;
+	bool wants_pen = adcsel & WM97XX_PEN_DOWN;
+
+	if (wants_pen && !wm->pen_probably_down) {
+		u16 data = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+		if (!(data & WM97XX_PEN_DOWN))
+			return RC_PENUP;
+		wm->pen_probably_down = 1;
+	}
+
+	/* set up digitiser */
+	if (wm->mach_ops && wm->mach_ops->pre_sample)
+		wm->mach_ops->pre_sample(adcsel);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, (adcsel & WM97XX_ADCSEL_MASK)
+				| WM97XX_POLL | WM97XX_DELAY(delay));
+
+	/* wait 3 AC97 time slots + delay for conversion */
+	poll_delay(delay);
+
+	/* wait for POLL to go low */
+	while ((wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER1) & WM97XX_POLL)
+	       && timeout) {
+		udelay(AC97_LINK_FRAME);
+		timeout--;
+	}
+
+	if (timeout <= 0) {
+		/* If PDEN is set, we can get a timeout when pen goes up */
+		if (is_pden(wm))
+			wm->pen_probably_down = 0;
+		else
+			dev_dbg(wm->dev, "adc sample timeout\n");
+		return RC_PENUP;
+	}
+
+	*sample = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	if (wm->mach_ops && wm->mach_ops->post_sample)
+		wm->mach_ops->post_sample(adcsel);
+
+	/* check we have correct sample */
+	if ((*sample ^ adcsel) & WM97XX_ADCSEL_MASK) {
+		dev_dbg(wm->dev, "adc wrong sample, wanted %x got %x\n",
+			adcsel & WM97XX_ADCSEL_MASK,
+			*sample & WM97XX_ADCSEL_MASK);
+		return RC_AGAIN;
+	}
+
+	if (wants_pen && !(*sample & WM97XX_PEN_DOWN)) {
+		/* Sometimes it reads a wrong value the first time. */
+		*sample = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+		if (!(*sample & WM97XX_PEN_DOWN)) {
+			wm->pen_probably_down = 0;
+			return RC_PENUP;
+		}
+	}
+
+	return RC_VALID;
+}
+
+/*
+ * Read a coord from the WM9712 adc in polling mode.
+ */
+static int wm9712_poll_coord(struct wm97xx *wm, struct wm97xx_data *data)
+{
+	int timeout = 5 * delay;
+
+	if (!wm->pen_probably_down) {
+		u16 data_rd = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+		if (!(data_rd & WM97XX_PEN_DOWN))
+			return RC_PENUP;
+		wm->pen_probably_down = 1;
+	}
+
+	/* set up digitiser */
+	if (wm->mach_ops && wm->mach_ops->pre_sample)
+		wm->mach_ops->pre_sample(WM97XX_ADCSEL_X | WM97XX_ADCSEL_Y);
+
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1,
+		WM97XX_COO | WM97XX_POLL | WM97XX_DELAY(delay));
+
+	/* wait 3 AC97 time slots + delay for conversion and read x */
+	poll_delay(delay);
+	data->x = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	/* wait for POLL to go low */
+	while ((wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER1) & WM97XX_POLL)
+	       && timeout) {
+		udelay(AC97_LINK_FRAME);
+		timeout--;
+	}
+
+	if (timeout <= 0) {
+		/* If PDEN is set, we can get a timeout when pen goes up */
+		if (is_pden(wm))
+			wm->pen_probably_down = 0;
+		else
+			dev_dbg(wm->dev, "adc sample timeout\n");
+		return RC_PENUP;
+	}
+
+	/* read back y data */
+	data->y = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	if (pil)
+		data->p = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+	else
+		data->p = DEFAULT_PRESSURE;
+
+	if (wm->mach_ops && wm->mach_ops->post_sample)
+		wm->mach_ops->post_sample(WM97XX_ADCSEL_X | WM97XX_ADCSEL_Y);
+
+	/* check we have correct sample */
+	if (!(data->x & WM97XX_ADCSEL_X) || !(data->y & WM97XX_ADCSEL_Y))
+		goto err;
+	if (pil && !(data->p & WM97XX_ADCSEL_PRES))
+		goto err;
+
+	if (!(data->x & WM97XX_PEN_DOWN) || !(data->y & WM97XX_PEN_DOWN)) {
+		wm->pen_probably_down = 0;
+		return RC_PENUP;
+	}
+	return RC_VALID;
+err:
+	return 0;
+}
+
+/*
+ * Sample the WM9712 touchscreen in polling mode
+ */
+static int wm9712_poll_touch(struct wm97xx *wm, struct wm97xx_data *data)
+{
+	int rc;
+
+	if (coord) {
+		rc = wm9712_poll_coord(wm, data);
+		if (rc != RC_VALID)
+			return rc;
+	} else {
+		rc = wm9712_poll_sample(wm, WM97XX_ADCSEL_X | WM97XX_PEN_DOWN,
+					&data->x);
+		if (rc != RC_VALID)
+			return rc;
+
+		rc = wm9712_poll_sample(wm, WM97XX_ADCSEL_Y | WM97XX_PEN_DOWN,
+					&data->y);
+		if (rc != RC_VALID)
+			return rc;
+
+		if (pil && !five_wire) {
+			rc = wm9712_poll_sample(wm, WM97XX_ADCSEL_PRES | WM97XX_PEN_DOWN,
+						&data->p);
+			if (rc != RC_VALID)
+				return rc;
+		} else
+			data->p = DEFAULT_PRESSURE;
+	}
+	return RC_VALID;
+}
+
+/*
+ * Enable WM9712 continuous mode, i.e. touch data is streamed across
+ * an AC97 slot
+ */
+static int wm9712_acc_enable(struct wm97xx *wm, int enable)
+{
+	u16 dig1, dig2;
+	int ret = 0;
+
+	dig1 = wm->dig[1];
+	dig2 = wm->dig[2];
+
+	if (enable) {
+		/* continuous mode */
+		if (wm->mach_ops->acc_startup) {
+			ret = wm->mach_ops->acc_startup(wm);
+			if (ret < 0)
+				return ret;
+		}
+		dig1 &= ~(WM97XX_CM_RATE_MASK | WM97XX_ADCSEL_MASK |
+			WM97XX_DELAY_MASK | WM97XX_SLT_MASK);
+		dig1 |= WM97XX_CTC | WM97XX_COO | WM97XX_SLEN |
+			WM97XX_DELAY(delay) |
+			WM97XX_SLT(wm->acc_slot) |
+			WM97XX_RATE(wm->acc_rate);
+		if (pil)
+			dig1 |= WM97XX_ADCSEL_PRES;
+		dig2 |= WM9712_PDEN;
+	} else {
+		dig1 &= ~(WM97XX_CTC | WM97XX_COO | WM97XX_SLEN);
+		dig2 &= ~WM9712_PDEN;
+		if (wm->mach_ops->acc_shutdown)
+			wm->mach_ops->acc_shutdown(wm);
+	}
+
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, dig1);
+	wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, dig2);
+
+	return 0;
+}
+
+struct wm97xx_codec_drv wm9712_codec = {
+	.id = WM9712_ID2,
+	.name = "wm9712",
+	.poll_sample = wm9712_poll_sample,
+	.poll_touch = wm9712_poll_touch,
+	.acc_enable = wm9712_acc_enable,
+	.phy_init = wm9712_phy_init,
+	.dig_enable = wm9712_dig_enable,
+	.dig_restore = wm9712_dig_restore,
+	.aux_prepare = wm9712_aux_prepare,
+};
+EXPORT_SYMBOL_GPL(wm9712_codec);
+
+/* Module information */
+MODULE_AUTHOR("Liam Girdwood <lrg@slimlogic.co.uk>");
+MODULE_DESCRIPTION("WM9712 Touch Screen Driver");
+MODULE_LICENSE("GPL");