Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 779 insertions, 0 deletions

diff --git a/drivers/mfd/ucb1x00-core.c b/drivers/mfd/ucb1x00-core.c
new file mode 100644
index 000000000..b690796d2
--- /dev/null
+++ b/drivers/mfd/ucb1x00-core.c
@@ -0,0 +1,779 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  linux/drivers/mfd/ucb1x00-core.c
+ *
+ *  Copyright (C) 2001 Russell King, All Rights Reserved.
+ *
+ *  The UCB1x00 core driver provides basic services for handling IO,
+ *  the ADC, interrupts, and accessing registers.  It is designed
+ *  such that everything goes through this layer, thereby providing
+ *  a consistent locking methodology, as well as allowing the drivers
+ *  to be used on other non-MCP-enabled hardware platforms.
+ *
+ *  Note that all locks are private to this file.  Nothing else may
+ *  touch them.
+ */
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/device.h>
+#include <linux/mutex.h>
+#include <linux/mfd/ucb1x00.h>
+#include <linux/pm.h>
+#include <linux/gpio/driver.h>
+
+static DEFINE_MUTEX(ucb1x00_mutex);
+static LIST_HEAD(ucb1x00_drivers);
+static LIST_HEAD(ucb1x00_devices);
+
+/**
+ *	ucb1x00_io_set_dir - set IO direction
+ *	@ucb: UCB1x00 structure describing chip
+ *	@in:  bitfield of IO pins to be set as inputs
+ *	@out: bitfield of IO pins to be set as outputs
+ *
+ *	Set the IO direction of the ten general purpose IO pins on
+ *	the UCB1x00 chip.  The @in bitfield has priority over the
+ *	@out bitfield, in that if you specify a pin as both input
+ *	and output, it will end up as an input.
+ *
+ *	ucb1x00_enable must have been called to enable the comms
+ *	before using this function.
+ *
+ *	This function takes a spinlock, disabling interrupts.
+ */
+void ucb1x00_io_set_dir(struct ucb1x00 *ucb, unsigned int in, unsigned int out)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&ucb->io_lock, flags);
+	ucb->io_dir |= out;
+	ucb->io_dir &= ~in;
+
+	ucb1x00_reg_write(ucb, UCB_IO_DIR, ucb->io_dir);
+	spin_unlock_irqrestore(&ucb->io_lock, flags);
+}
+
+/**
+ *	ucb1x00_io_write - set or clear IO outputs
+ *	@ucb:   UCB1x00 structure describing chip
+ *	@set:   bitfield of IO pins to set to logic '1'
+ *	@clear: bitfield of IO pins to set to logic '0'
+ *
+ *	Set the IO output state of the specified IO pins.  The value
+ *	is retained if the pins are subsequently configured as inputs.
+ *	The @clear bitfield has priority over the @set bitfield -
+ *	outputs will be cleared.
+ *
+ *	ucb1x00_enable must have been called to enable the comms
+ *	before using this function.
+ *
+ *	This function takes a spinlock, disabling interrupts.
+ */
+void ucb1x00_io_write(struct ucb1x00 *ucb, unsigned int set, unsigned int clear)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&ucb->io_lock, flags);
+	ucb->io_out |= set;
+	ucb->io_out &= ~clear;
+
+	ucb1x00_reg_write(ucb, UCB_IO_DATA, ucb->io_out);
+	spin_unlock_irqrestore(&ucb->io_lock, flags);
+}
+
+/**
+ *	ucb1x00_io_read - read the current state of the IO pins
+ *	@ucb: UCB1x00 structure describing chip
+ *
+ *	Return a bitfield describing the logic state of the ten
+ *	general purpose IO pins.
+ *
+ *	ucb1x00_enable must have been called to enable the comms
+ *	before using this function.
+ *
+ *	This function does not take any mutexes or spinlocks.
+ */
+unsigned int ucb1x00_io_read(struct ucb1x00 *ucb)
+{
+	return ucb1x00_reg_read(ucb, UCB_IO_DATA);
+}
+
+static void ucb1x00_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+	struct ucb1x00 *ucb = gpiochip_get_data(chip);
+	unsigned long flags;
+
+	spin_lock_irqsave(&ucb->io_lock, flags);
+	if (value)
+		ucb->io_out |= 1 << offset;
+	else
+		ucb->io_out &= ~(1 << offset);
+
+	ucb1x00_enable(ucb);
+	ucb1x00_reg_write(ucb, UCB_IO_DATA, ucb->io_out);
+	ucb1x00_disable(ucb);
+	spin_unlock_irqrestore(&ucb->io_lock, flags);
+}
+
+static int ucb1x00_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+	struct ucb1x00 *ucb = gpiochip_get_data(chip);
+	unsigned val;
+
+	ucb1x00_enable(ucb);
+	val = ucb1x00_reg_read(ucb, UCB_IO_DATA);
+	ucb1x00_disable(ucb);
+
+	return !!(val & (1 << offset));
+}
+
+static int ucb1x00_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+	struct ucb1x00 *ucb = gpiochip_get_data(chip);
+	unsigned long flags;
+
+	spin_lock_irqsave(&ucb->io_lock, flags);
+	ucb->io_dir &= ~(1 << offset);
+	ucb1x00_enable(ucb);
+	ucb1x00_reg_write(ucb, UCB_IO_DIR, ucb->io_dir);
+	ucb1x00_disable(ucb);
+	spin_unlock_irqrestore(&ucb->io_lock, flags);
+
+	return 0;
+}
+
+static int ucb1x00_gpio_direction_output(struct gpio_chip *chip, unsigned offset
+		, int value)
+{
+	struct ucb1x00 *ucb = gpiochip_get_data(chip);
+	unsigned long flags;
+	unsigned old, mask = 1 << offset;
+
+	spin_lock_irqsave(&ucb->io_lock, flags);
+	old = ucb->io_out;
+	if (value)
+		ucb->io_out |= mask;
+	else
+		ucb->io_out &= ~mask;
+
+	ucb1x00_enable(ucb);
+	if (old != ucb->io_out)
+		ucb1x00_reg_write(ucb, UCB_IO_DATA, ucb->io_out);
+
+	if (!(ucb->io_dir & mask)) {
+		ucb->io_dir |= mask;
+		ucb1x00_reg_write(ucb, UCB_IO_DIR, ucb->io_dir);
+	}
+	ucb1x00_disable(ucb);
+	spin_unlock_irqrestore(&ucb->io_lock, flags);
+
+	return 0;
+}
+
+static int ucb1x00_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+	struct ucb1x00 *ucb = gpiochip_get_data(chip);
+
+	return ucb->irq_base > 0 ? ucb->irq_base + offset : -ENXIO;
+}
+
+/*
+ * UCB1300 data sheet says we must:
+ *  1. enable ADC	=> 5us (including reference startup time)
+ *  2. select input	=> 51*tsibclk  => 4.3us
+ *  3. start conversion	=> 102*tsibclk => 8.5us
+ * (tsibclk = 1/11981000)
+ * Period between SIB 128-bit frames = 10.7us
+ */
+
+/**
+ *	ucb1x00_adc_enable - enable the ADC converter
+ *	@ucb: UCB1x00 structure describing chip
+ *
+ *	Enable the ucb1x00 and ADC converter on the UCB1x00 for use.
+ *	Any code wishing to use the ADC converter must call this
+ *	function prior to using it.
+ *
+ *	This function takes the ADC mutex to prevent two or more
+ *	concurrent uses, and therefore may sleep.  As a result, it
+ *	can only be called from process context, not interrupt
+ *	context.
+ *
+ *	You should release the ADC as soon as possible using
+ *	ucb1x00_adc_disable.
+ */
+void ucb1x00_adc_enable(struct ucb1x00 *ucb)
+{
+	mutex_lock(&ucb->adc_mutex);
+
+	ucb->adc_cr |= UCB_ADC_ENA;
+
+	ucb1x00_enable(ucb);
+	ucb1x00_reg_write(ucb, UCB_ADC_CR, ucb->adc_cr);
+}
+
+/**
+ *	ucb1x00_adc_read - read the specified ADC channel
+ *	@ucb: UCB1x00 structure describing chip
+ *	@adc_channel: ADC channel mask
+ *	@sync: wait for syncronisation pulse.
+ *
+ *	Start an ADC conversion and wait for the result.  Note that
+ *	synchronised ADC conversions (via the ADCSYNC pin) must wait
+ *	until the trigger is asserted and the conversion is finished.
+ *
+ *	This function currently spins waiting for the conversion to
+ *	complete (2 frames max without sync).
+ *
+ *	If called for a synchronised ADC conversion, it may sleep
+ *	with the ADC mutex held.
+ */
+unsigned int ucb1x00_adc_read(struct ucb1x00 *ucb, int adc_channel, int sync)
+{
+	unsigned int val;
+
+	if (sync)
+		adc_channel |= UCB_ADC_SYNC_ENA;
+
+	ucb1x00_reg_write(ucb, UCB_ADC_CR, ucb->adc_cr | adc_channel);
+	ucb1x00_reg_write(ucb, UCB_ADC_CR, ucb->adc_cr | adc_channel | UCB_ADC_START);
+
+	for (;;) {
+		val = ucb1x00_reg_read(ucb, UCB_ADC_DATA);
+		if (val & UCB_ADC_DAT_VAL)
+			break;
+		/* yield to other processes */
+		set_current_state(TASK_INTERRUPTIBLE);
+		schedule_timeout(1);
+	}
+
+	return UCB_ADC_DAT(val);
+}
+
+/**
+ *	ucb1x00_adc_disable - disable the ADC converter
+ *	@ucb: UCB1x00 structure describing chip
+ *
+ *	Disable the ADC converter and release the ADC mutex.
+ */
+void ucb1x00_adc_disable(struct ucb1x00 *ucb)
+{
+	ucb->adc_cr &= ~UCB_ADC_ENA;
+	ucb1x00_reg_write(ucb, UCB_ADC_CR, ucb->adc_cr);
+	ucb1x00_disable(ucb);
+
+	mutex_unlock(&ucb->adc_mutex);
+}
+
+/*
+ * UCB1x00 Interrupt handling.
+ *
+ * The UCB1x00 can generate interrupts when the SIBCLK is stopped.
+ * Since we need to read an internal register, we must re-enable
+ * SIBCLK to talk to the chip.  We leave the clock running until
+ * we have finished processing all interrupts from the chip.
+ */
+static void ucb1x00_irq(struct irq_desc *desc)
+{
+	struct ucb1x00 *ucb = irq_desc_get_handler_data(desc);
+	unsigned int isr, i;
+
+	ucb1x00_enable(ucb);
+	isr = ucb1x00_reg_read(ucb, UCB_IE_STATUS);
+	ucb1x00_reg_write(ucb, UCB_IE_CLEAR, isr);
+	ucb1x00_reg_write(ucb, UCB_IE_CLEAR, 0);
+
+	for (i = 0; i < 16 && isr; i++, isr >>= 1)
+		if (isr & 1)
+			generic_handle_irq(ucb->irq_base + i);
+	ucb1x00_disable(ucb);
+}
+
+static void ucb1x00_irq_update(struct ucb1x00 *ucb, unsigned mask)
+{
+	ucb1x00_enable(ucb);
+	if (ucb->irq_ris_enbl & mask)
+		ucb1x00_reg_write(ucb, UCB_IE_RIS, ucb->irq_ris_enbl &
+				  ucb->irq_mask);
+	if (ucb->irq_fal_enbl & mask)
+		ucb1x00_reg_write(ucb, UCB_IE_FAL, ucb->irq_fal_enbl &
+				  ucb->irq_mask);
+	ucb1x00_disable(ucb);
+}
+
+static void ucb1x00_irq_noop(struct irq_data *data)
+{
+}
+
+static void ucb1x00_irq_mask(struct irq_data *data)
+{
+	struct ucb1x00 *ucb = irq_data_get_irq_chip_data(data);
+	unsigned mask = 1 << (data->irq - ucb->irq_base);
+
+	raw_spin_lock(&ucb->irq_lock);
+	ucb->irq_mask &= ~mask;
+	ucb1x00_irq_update(ucb, mask);
+	raw_spin_unlock(&ucb->irq_lock);
+}
+
+static void ucb1x00_irq_unmask(struct irq_data *data)
+{
+	struct ucb1x00 *ucb = irq_data_get_irq_chip_data(data);
+	unsigned mask = 1 << (data->irq - ucb->irq_base);
+
+	raw_spin_lock(&ucb->irq_lock);
+	ucb->irq_mask |= mask;
+	ucb1x00_irq_update(ucb, mask);
+	raw_spin_unlock(&ucb->irq_lock);
+}
+
+static int ucb1x00_irq_set_type(struct irq_data *data, unsigned int type)
+{
+	struct ucb1x00 *ucb = irq_data_get_irq_chip_data(data);
+	unsigned mask = 1 << (data->irq - ucb->irq_base);
+
+	raw_spin_lock(&ucb->irq_lock);
+	if (type & IRQ_TYPE_EDGE_RISING)
+		ucb->irq_ris_enbl |= mask;
+	else
+		ucb->irq_ris_enbl &= ~mask;
+
+	if (type & IRQ_TYPE_EDGE_FALLING)
+		ucb->irq_fal_enbl |= mask;
+	else
+		ucb->irq_fal_enbl &= ~mask;
+	if (ucb->irq_mask & mask) {
+		ucb1x00_reg_write(ucb, UCB_IE_RIS, ucb->irq_ris_enbl &
+				  ucb->irq_mask);
+		ucb1x00_reg_write(ucb, UCB_IE_FAL, ucb->irq_fal_enbl &
+				  ucb->irq_mask);
+	}
+	raw_spin_unlock(&ucb->irq_lock);
+
+	return 0;
+}
+
+static int ucb1x00_irq_set_wake(struct irq_data *data, unsigned int on)
+{
+	struct ucb1x00 *ucb = irq_data_get_irq_chip_data(data);
+	struct ucb1x00_plat_data *pdata = ucb->mcp->attached_device.platform_data;
+	unsigned mask = 1 << (data->irq - ucb->irq_base);
+
+	if (!pdata || !pdata->can_wakeup)
+		return -EINVAL;
+
+	raw_spin_lock(&ucb->irq_lock);
+	if (on)
+		ucb->irq_wake |= mask;
+	else
+		ucb->irq_wake &= ~mask;
+	raw_spin_unlock(&ucb->irq_lock);
+
+	return 0;
+}
+
+static struct irq_chip ucb1x00_irqchip = {
+	.name = "ucb1x00",
+	.irq_ack = ucb1x00_irq_noop,
+	.irq_mask = ucb1x00_irq_mask,
+	.irq_unmask = ucb1x00_irq_unmask,
+	.irq_set_type = ucb1x00_irq_set_type,
+	.irq_set_wake = ucb1x00_irq_set_wake,
+};
+
+static int ucb1x00_add_dev(struct ucb1x00 *ucb, struct ucb1x00_driver *drv)
+{
+	struct ucb1x00_dev *dev;
+	int ret;
+
+	dev = kmalloc(sizeof(struct ucb1x00_dev), GFP_KERNEL);
+	if (!dev)
+		return -ENOMEM;
+
+	dev->ucb = ucb;
+	dev->drv = drv;
+
+	ret = drv->add(dev);
+	if (ret) {
+		kfree(dev);
+		return ret;
+	}
+
+	list_add_tail(&dev->dev_node, &ucb->devs);
+	list_add_tail(&dev->drv_node, &drv->devs);
+
+	return ret;
+}
+
+static void ucb1x00_remove_dev(struct ucb1x00_dev *dev)
+{
+	dev->drv->remove(dev);
+	list_del(&dev->dev_node);
+	list_del(&dev->drv_node);
+	kfree(dev);
+}
+
+/*
+ * Try to probe our interrupt, rather than relying on lots of
+ * hard-coded machine dependencies.  For reference, the expected
+ * IRQ mappings are:
+ *
+ *  	Machine		Default IRQ
+ *	adsbitsy	IRQ_GPCIN4
+ *	cerf		IRQ_GPIO_UCB1200_IRQ
+ *	flexanet	IRQ_GPIO_GUI
+ *	freebird	IRQ_GPIO_FREEBIRD_UCB1300_IRQ
+ *	graphicsclient	ADS_EXT_IRQ(8)
+ *	graphicsmaster	ADS_EXT_IRQ(8)
+ *	lart		LART_IRQ_UCB1200
+ *	omnimeter	IRQ_GPIO23
+ *	pfs168		IRQ_GPIO_UCB1300_IRQ
+ *	simpad		IRQ_GPIO_UCB1300_IRQ
+ *	shannon		SHANNON_IRQ_GPIO_IRQ_CODEC
+ *	yopy		IRQ_GPIO_UCB1200_IRQ
+ */
+static int ucb1x00_detect_irq(struct ucb1x00 *ucb)
+{
+	unsigned long mask;
+
+	mask = probe_irq_on();
+
+	/*
+	 * Enable the ADC interrupt.
+	 */
+	ucb1x00_reg_write(ucb, UCB_IE_RIS, UCB_IE_ADC);
+	ucb1x00_reg_write(ucb, UCB_IE_FAL, UCB_IE_ADC);
+	ucb1x00_reg_write(ucb, UCB_IE_CLEAR, 0xffff);
+	ucb1x00_reg_write(ucb, UCB_IE_CLEAR, 0);
+
+	/*
+	 * Cause an ADC interrupt.
+	 */
+	ucb1x00_reg_write(ucb, UCB_ADC_CR, UCB_ADC_ENA);
+	ucb1x00_reg_write(ucb, UCB_ADC_CR, UCB_ADC_ENA | UCB_ADC_START);
+
+	/*
+	 * Wait for the conversion to complete.
+	 */
+	while ((ucb1x00_reg_read(ucb, UCB_ADC_DATA) & UCB_ADC_DAT_VAL) == 0);
+	ucb1x00_reg_write(ucb, UCB_ADC_CR, 0);
+
+	/*
+	 * Disable and clear interrupt.
+	 */
+	ucb1x00_reg_write(ucb, UCB_IE_RIS, 0);
+	ucb1x00_reg_write(ucb, UCB_IE_FAL, 0);
+	ucb1x00_reg_write(ucb, UCB_IE_CLEAR, 0xffff);
+	ucb1x00_reg_write(ucb, UCB_IE_CLEAR, 0);
+
+	/*
+	 * Read triggered interrupt.
+	 */
+	return probe_irq_off(mask);
+}
+
+static void ucb1x00_release(struct device *dev)
+{
+	struct ucb1x00 *ucb = classdev_to_ucb1x00(dev);
+	kfree(ucb);
+}
+
+static struct class ucb1x00_class = {
+	.name		= "ucb1x00",
+	.dev_release	= ucb1x00_release,
+};
+
+static int ucb1x00_probe(struct mcp *mcp)
+{
+	struct ucb1x00_plat_data *pdata = mcp->attached_device.platform_data;
+	struct ucb1x00_driver *drv;
+	struct ucb1x00 *ucb;
+	unsigned id, i, irq_base;
+	int ret = -ENODEV;
+
+	/* Tell the platform to deassert the UCB1x00 reset */
+	if (pdata && pdata->reset)
+		pdata->reset(UCB_RST_PROBE);
+
+	mcp_enable(mcp);
+	id = mcp_reg_read(mcp, UCB_ID);
+	mcp_disable(mcp);
+
+	if (id != UCB_ID_1200 && id != UCB_ID_1300 && id != UCB_ID_TC35143) {
+		printk(KERN_WARNING "UCB1x00 ID not found: %04x\n", id);
+		goto out;
+	}
+
+	ucb = kzalloc(sizeof(struct ucb1x00), GFP_KERNEL);
+	ret = -ENOMEM;
+	if (!ucb)
+		goto out;
+
+	device_initialize(&ucb->dev);
+	ucb->dev.class = &ucb1x00_class;
+	ucb->dev.parent = &mcp->attached_device;
+	dev_set_name(&ucb->dev, "ucb1x00");
+
+	raw_spin_lock_init(&ucb->irq_lock);
+	spin_lock_init(&ucb->io_lock);
+	mutex_init(&ucb->adc_mutex);
+
+	ucb->id  = id;
+	ucb->mcp = mcp;
+
+	ret = device_add(&ucb->dev);
+	if (ret)
+		goto err_dev_add;
+
+	ucb1x00_enable(ucb);
+	ucb->irq = ucb1x00_detect_irq(ucb);
+	ucb1x00_disable(ucb);
+	if (!ucb->irq) {
+		dev_err(&ucb->dev, "IRQ probe failed\n");
+		ret = -ENODEV;
+		goto err_no_irq;
+	}
+
+	ucb->gpio.base = -1;
+	irq_base = pdata ? pdata->irq_base : 0;
+	ucb->irq_base = irq_alloc_descs(-1, irq_base, 16, -1);
+	if (ucb->irq_base < 0) {
+		dev_err(&ucb->dev, "unable to allocate 16 irqs: %d\n",
+			ucb->irq_base);
+		ret = ucb->irq_base;
+		goto err_irq_alloc;
+	}
+
+	for (i = 0; i < 16; i++) {
+		unsigned irq = ucb->irq_base + i;
+
+		irq_set_chip_and_handler(irq, &ucb1x00_irqchip, handle_edge_irq);
+		irq_set_chip_data(irq, ucb);
+		irq_clear_status_flags(irq, IRQ_NOREQUEST);
+	}
+
+	irq_set_irq_type(ucb->irq, IRQ_TYPE_EDGE_RISING);
+	irq_set_chained_handler_and_data(ucb->irq, ucb1x00_irq, ucb);
+
+	if (pdata && pdata->gpio_base) {
+		ucb->gpio.label = dev_name(&ucb->dev);
+		ucb->gpio.parent = &ucb->dev;
+		ucb->gpio.owner = THIS_MODULE;
+		ucb->gpio.base = pdata->gpio_base;
+		ucb->gpio.ngpio = 10;
+		ucb->gpio.set = ucb1x00_gpio_set;
+		ucb->gpio.get = ucb1x00_gpio_get;
+		ucb->gpio.direction_input = ucb1x00_gpio_direction_input;
+		ucb->gpio.direction_output = ucb1x00_gpio_direction_output;
+		ucb->gpio.to_irq = ucb1x00_to_irq;
+		ret = gpiochip_add_data(&ucb->gpio, ucb);
+		if (ret)
+			goto err_gpio_add;
+	} else
+		dev_info(&ucb->dev, "gpio_base not set so no gpiolib support");
+
+	mcp_set_drvdata(mcp, ucb);
+
+	if (pdata)
+		device_set_wakeup_capable(&ucb->dev, pdata->can_wakeup);
+
+	INIT_LIST_HEAD(&ucb->devs);
+	mutex_lock(&ucb1x00_mutex);
+	list_add_tail(&ucb->node, &ucb1x00_devices);
+	list_for_each_entry(drv, &ucb1x00_drivers, node) {
+		ucb1x00_add_dev(ucb, drv);
+	}
+	mutex_unlock(&ucb1x00_mutex);
+
+	return ret;
+
+ err_gpio_add:
+	irq_set_chained_handler(ucb->irq, NULL);
+ err_irq_alloc:
+	if (ucb->irq_base > 0)
+		irq_free_descs(ucb->irq_base, 16);
+ err_no_irq:
+	device_del(&ucb->dev);
+ err_dev_add:
+	put_device(&ucb->dev);
+ out:
+	if (pdata && pdata->reset)
+		pdata->reset(UCB_RST_PROBE_FAIL);
+	return ret;
+}
+
+static void ucb1x00_remove(struct mcp *mcp)
+{
+	struct ucb1x00_plat_data *pdata = mcp->attached_device.platform_data;
+	struct ucb1x00 *ucb = mcp_get_drvdata(mcp);
+	struct list_head *l, *n;
+
+	mutex_lock(&ucb1x00_mutex);
+	list_del(&ucb->node);
+	list_for_each_safe(l, n, &ucb->devs) {
+		struct ucb1x00_dev *dev = list_entry(l, struct ucb1x00_dev, dev_node);
+		ucb1x00_remove_dev(dev);
+	}
+	mutex_unlock(&ucb1x00_mutex);
+
+	if (ucb->gpio.base != -1)
+		gpiochip_remove(&ucb->gpio);
+
+	irq_set_chained_handler(ucb->irq, NULL);
+	irq_free_descs(ucb->irq_base, 16);
+	device_unregister(&ucb->dev);
+
+	if (pdata && pdata->reset)
+		pdata->reset(UCB_RST_REMOVE);
+}
+
+int ucb1x00_register_driver(struct ucb1x00_driver *drv)
+{
+	struct ucb1x00 *ucb;
+
+	INIT_LIST_HEAD(&drv->devs);
+	mutex_lock(&ucb1x00_mutex);
+	list_add_tail(&drv->node, &ucb1x00_drivers);
+	list_for_each_entry(ucb, &ucb1x00_devices, node) {
+		ucb1x00_add_dev(ucb, drv);
+	}
+	mutex_unlock(&ucb1x00_mutex);
+	return 0;
+}
+
+void ucb1x00_unregister_driver(struct ucb1x00_driver *drv)
+{
+	struct list_head *n, *l;
+
+	mutex_lock(&ucb1x00_mutex);
+	list_del(&drv->node);
+	list_for_each_safe(l, n, &drv->devs) {
+		struct ucb1x00_dev *dev = list_entry(l, struct ucb1x00_dev, drv_node);
+		ucb1x00_remove_dev(dev);
+	}
+	mutex_unlock(&ucb1x00_mutex);
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int ucb1x00_suspend(struct device *dev)
+{
+	struct ucb1x00_plat_data *pdata = dev_get_platdata(dev);
+	struct ucb1x00 *ucb = dev_get_drvdata(dev);
+	struct ucb1x00_dev *udev;
+
+	mutex_lock(&ucb1x00_mutex);
+	list_for_each_entry(udev, &ucb->devs, dev_node) {
+		if (udev->drv->suspend)
+			udev->drv->suspend(udev);
+	}
+	mutex_unlock(&ucb1x00_mutex);
+
+	if (ucb->irq_wake) {
+		unsigned long flags;
+
+		raw_spin_lock_irqsave(&ucb->irq_lock, flags);
+		ucb1x00_enable(ucb);
+		ucb1x00_reg_write(ucb, UCB_IE_RIS, ucb->irq_ris_enbl &
+				  ucb->irq_wake);
+		ucb1x00_reg_write(ucb, UCB_IE_FAL, ucb->irq_fal_enbl &
+				  ucb->irq_wake);
+		ucb1x00_disable(ucb);
+		raw_spin_unlock_irqrestore(&ucb->irq_lock, flags);
+
+		enable_irq_wake(ucb->irq);
+	} else if (pdata && pdata->reset)
+		pdata->reset(UCB_RST_SUSPEND);
+
+	return 0;
+}
+
+static int ucb1x00_resume(struct device *dev)
+{
+	struct ucb1x00_plat_data *pdata = dev_get_platdata(dev);
+	struct ucb1x00 *ucb = dev_get_drvdata(dev);
+	struct ucb1x00_dev *udev;
+
+	if (!ucb->irq_wake && pdata && pdata->reset)
+		pdata->reset(UCB_RST_RESUME);
+
+	ucb1x00_enable(ucb);
+	ucb1x00_reg_write(ucb, UCB_IO_DATA, ucb->io_out);
+	ucb1x00_reg_write(ucb, UCB_IO_DIR, ucb->io_dir);
+
+	if (ucb->irq_wake) {
+		unsigned long flags;
+
+		raw_spin_lock_irqsave(&ucb->irq_lock, flags);
+		ucb1x00_reg_write(ucb, UCB_IE_RIS, ucb->irq_ris_enbl &
+				  ucb->irq_mask);
+		ucb1x00_reg_write(ucb, UCB_IE_FAL, ucb->irq_fal_enbl &
+				  ucb->irq_mask);
+		raw_spin_unlock_irqrestore(&ucb->irq_lock, flags);
+
+		disable_irq_wake(ucb->irq);
+	}
+	ucb1x00_disable(ucb);
+
+	mutex_lock(&ucb1x00_mutex);
+	list_for_each_entry(udev, &ucb->devs, dev_node) {
+		if (udev->drv->resume)
+			udev->drv->resume(udev);
+	}
+	mutex_unlock(&ucb1x00_mutex);
+	return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(ucb1x00_pm_ops, ucb1x00_suspend, ucb1x00_resume);
+
+static struct mcp_driver ucb1x00_driver = {
+	.drv		= {
+		.name	= "ucb1x00",
+		.owner	= THIS_MODULE,
+		.pm	= &ucb1x00_pm_ops,
+	},
+	.probe		= ucb1x00_probe,
+	.remove		= ucb1x00_remove,
+};
+
+static int __init ucb1x00_init(void)
+{
+	int ret = class_register(&ucb1x00_class);
+	if (ret == 0) {
+		ret = mcp_driver_register(&ucb1x00_driver);
+		if (ret)
+			class_unregister(&ucb1x00_class);
+	}
+	return ret;
+}
+
+static void __exit ucb1x00_exit(void)
+{
+	mcp_driver_unregister(&ucb1x00_driver);
+	class_unregister(&ucb1x00_class);
+}
+
+module_init(ucb1x00_init);
+module_exit(ucb1x00_exit);
+
+EXPORT_SYMBOL(ucb1x00_io_set_dir);
+EXPORT_SYMBOL(ucb1x00_io_write);
+EXPORT_SYMBOL(ucb1x00_io_read);
+
+EXPORT_SYMBOL(ucb1x00_adc_enable);
+EXPORT_SYMBOL(ucb1x00_adc_read);
+EXPORT_SYMBOL(ucb1x00_adc_disable);
+
+EXPORT_SYMBOL(ucb1x00_register_driver);
+EXPORT_SYMBOL(ucb1x00_unregister_driver);
+
+MODULE_ALIAS("mcp:ucb1x00");
+MODULE_AUTHOR("Russell King <rmk@arm.linux.org.uk>");
+MODULE_DESCRIPTION("UCB1x00 core driver");
+MODULE_LICENSE("GPL");