Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 239 insertions, 0 deletions

diff --git a/drivers/misc/mei/hw-txe-regs.h b/drivers/misc/mei/hw-txe-regs.h
new file mode 100644
index 000000000..a92b306da
--- /dev/null
+++ b/drivers/misc/mei/hw-txe-regs.h
@@ -0,0 +1,239 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
+/*
+ * Copyright (c) 2013-2014, Intel Corporation. All rights reserved.
+ * Intel Management Engine Interface (Intel MEI) Linux driver
+ */
+#ifndef _MEI_HW_TXE_REGS_H_
+#define _MEI_HW_TXE_REGS_H_
+
+#include "hw.h"
+
+#define SEC_ALIVENESS_TIMER_TIMEOUT        (5 * MSEC_PER_SEC)
+#define SEC_ALIVENESS_WAIT_TIMEOUT         (1 * MSEC_PER_SEC)
+#define SEC_RESET_WAIT_TIMEOUT             (1 * MSEC_PER_SEC)
+#define SEC_READY_WAIT_TIMEOUT             (5 * MSEC_PER_SEC)
+#define START_MESSAGE_RESPONSE_WAIT_TIMEOUT (5 * MSEC_PER_SEC)
+#define RESET_CANCEL_WAIT_TIMEOUT          (1 * MSEC_PER_SEC)
+
+enum {
+	SEC_BAR,
+	BRIDGE_BAR,
+
+	NUM_OF_MEM_BARS
+};
+
+/* SeC FW Status Register
+ *
+ * FW uses this register in order to report its status to host.
+ * This register resides in PCI-E config space.
+ */
+#define PCI_CFG_TXE_FW_STS0   0x40
+#  define PCI_CFG_TXE_FW_STS0_WRK_ST_MSK    0x0000000F
+#  define PCI_CFG_TXE_FW_STS0_OP_ST_MSK     0x000001C0
+#  define PCI_CFG_TXE_FW_STS0_FW_INIT_CMPLT 0x00000200
+#  define PCI_CFG_TXE_FW_STS0_ERR_CODE_MSK  0x0000F000
+#  define PCI_CFG_TXE_FW_STS0_OP_MODE_MSK   0x000F0000
+#  define PCI_CFG_TXE_FW_STS0_RST_CNT_MSK   0x00F00000
+#define PCI_CFG_TXE_FW_STS1   0x48
+
+#define IPC_BASE_ADDR	0x80400 /* SeC IPC Base Address */
+
+/* IPC Input Doorbell Register */
+#define SEC_IPC_INPUT_DOORBELL_REG       (0x0000 + IPC_BASE_ADDR)
+
+/* IPC Input Status Register
+ * This register indicates whether or not processing of
+ * the most recent command has been completed by the SEC
+ * New commands and payloads should not be written by the Host
+ * until this indicates that the previous command has been processed.
+ */
+#define SEC_IPC_INPUT_STATUS_REG         (0x0008 + IPC_BASE_ADDR)
+#  define SEC_IPC_INPUT_STATUS_RDY    BIT(0)
+
+/* IPC Host Interrupt Status Register */
+#define SEC_IPC_HOST_INT_STATUS_REG      (0x0010 + IPC_BASE_ADDR)
+#define   SEC_IPC_HOST_INT_STATUS_OUT_DB             BIT(0)
+#define   SEC_IPC_HOST_INT_STATUS_IN_RDY             BIT(1)
+#define   SEC_IPC_HOST_INT_STATUS_HDCP_M0_RCVD       BIT(5)
+#define   SEC_IPC_HOST_INT_STATUS_ILL_MEM_ACCESS     BIT(17)
+#define   SEC_IPC_HOST_INT_STATUS_AES_HKEY_ERR       BIT(18)
+#define   SEC_IPC_HOST_INT_STATUS_DES_HKEY_ERR       BIT(19)
+#define   SEC_IPC_HOST_INT_STATUS_TMRMTB_OVERFLOW    BIT(21)
+
+/* Convenient mask for pending interrupts */
+#define   SEC_IPC_HOST_INT_STATUS_PENDING \
+		(SEC_IPC_HOST_INT_STATUS_OUT_DB| \
+		SEC_IPC_HOST_INT_STATUS_IN_RDY)
+
+/* IPC Host Interrupt Mask Register */
+#define SEC_IPC_HOST_INT_MASK_REG        (0x0014 + IPC_BASE_ADDR)
+
+#  define SEC_IPC_HOST_INT_MASK_OUT_DB	BIT(0) /* Output Doorbell Int Mask */
+#  define SEC_IPC_HOST_INT_MASK_IN_RDY	BIT(1) /* Input Ready Int Mask */
+
+/* IPC Input Payload RAM */
+#define SEC_IPC_INPUT_PAYLOAD_REG        (0x0100 + IPC_BASE_ADDR)
+/* IPC Shared Payload RAM */
+#define IPC_SHARED_PAYLOAD_REG           (0x0200 + IPC_BASE_ADDR)
+
+/* SeC Address Translation Table Entry 2 - Ctrl
+ *
+ * This register resides also in SeC's PCI-E Memory space.
+ */
+#define SATT2_CTRL_REG                   0x1040
+#  define SATT2_CTRL_VALID_MSK            BIT(0)
+#  define SATT2_CTRL_BR_BASE_ADDR_REG_SHIFT 8
+#  define SATT2_CTRL_BRIDGE_HOST_EN_MSK   BIT(12)
+
+/* SATT Table Entry 2 SAP Base Address Register */
+#define SATT2_SAP_BA_REG                 0x1044
+/* SATT Table Entry 2 SAP Size Register. */
+#define SATT2_SAP_SIZE_REG               0x1048
+ /* SATT Table Entry 2 SAP Bridge Address - LSB Register */
+#define SATT2_BRG_BA_LSB_REG             0x104C
+
+/* Host High-level Interrupt Status Register */
+#define HHISR_REG                        0x2020
+/* Host High-level Interrupt Enable Register
+ *
+ * Resides in PCI memory space. This is the top hierarchy for
+ * interrupts from SeC to host, aggregating both interrupts that
+ * arrive through HICR registers as well as interrupts
+ * that arrive via IPC.
+ */
+#define HHIER_REG                        0x2024
+#define   IPC_HHIER_SEC	BIT(0)
+#define   IPC_HHIER_BRIDGE	BIT(1)
+#define   IPC_HHIER_MSK	(IPC_HHIER_SEC | IPC_HHIER_BRIDGE)
+
+/* Host High-level Interrupt Mask Register.
+ *
+ * Resides in PCI memory space.
+ * This is the top hierarchy for masking interrupts from SeC to host.
+ */
+#define HHIMR_REG                        0x2028
+#define   IPC_HHIMR_SEC       BIT(0)
+#define   IPC_HHIMR_BRIDGE    BIT(1)
+
+/* Host High-level IRQ Status Register */
+#define HHIRQSR_REG                      0x202C
+
+/* Host Interrupt Cause Register 0 - SeC IPC Readiness
+ *
+ * This register is both an ICR to Host from PCI Memory Space
+ * and it is also exposed in the SeC memory space.
+ * This register is used by SeC's IPC driver in order
+ * to synchronize with host about IPC interface state.
+ */
+#define HICR_SEC_IPC_READINESS_REG       0x2040
+#define   HICR_SEC_IPC_READINESS_HOST_RDY  BIT(0)
+#define   HICR_SEC_IPC_READINESS_SEC_RDY   BIT(1)
+#define   HICR_SEC_IPC_READINESS_SYS_RDY     \
+	  (HICR_SEC_IPC_READINESS_HOST_RDY | \
+	   HICR_SEC_IPC_READINESS_SEC_RDY)
+#define   HICR_SEC_IPC_READINESS_RDY_CLR   BIT(2)
+
+/* Host Interrupt Cause Register 1 - Aliveness Response */
+/* This register is both an ICR to Host from PCI Memory Space
+ * and it is also exposed in the SeC memory space.
+ * The register may be used by SeC to ACK a host request for aliveness.
+ */
+#define HICR_HOST_ALIVENESS_RESP_REG     0x2044
+#define   HICR_HOST_ALIVENESS_RESP_ACK    BIT(0)
+
+/* Host Interrupt Cause Register 2 - SeC IPC Output Doorbell */
+#define HICR_SEC_IPC_OUTPUT_DOORBELL_REG 0x2048
+
+/* Host Interrupt Status Register.
+ *
+ * Resides in PCI memory space.
+ * This is the main register involved in generating interrupts
+ * from SeC to host via HICRs.
+ * The interrupt generation rules are as follows:
+ * An interrupt will be generated whenever for any i,
+ * there is a transition from a state where at least one of
+ * the following conditions did not hold, to a state where
+ * ALL the following conditions hold:
+ * A) HISR.INT[i]_STS == 1.
+ * B) HIER.INT[i]_EN == 1.
+ */
+#define HISR_REG                         0x2060
+#define   HISR_INT_0_STS      BIT(0)
+#define   HISR_INT_1_STS      BIT(1)
+#define   HISR_INT_2_STS      BIT(2)
+#define   HISR_INT_3_STS      BIT(3)
+#define   HISR_INT_4_STS      BIT(4)
+#define   HISR_INT_5_STS      BIT(5)
+#define   HISR_INT_6_STS      BIT(6)
+#define   HISR_INT_7_STS      BIT(7)
+#define   HISR_INT_STS_MSK \
+	(HISR_INT_0_STS | HISR_INT_1_STS | HISR_INT_2_STS)
+
+/* Host Interrupt Enable Register. Resides in PCI memory space. */
+#define HIER_REG                         0x2064
+#define   HIER_INT_0_EN      BIT(0)
+#define   HIER_INT_1_EN      BIT(1)
+#define   HIER_INT_2_EN      BIT(2)
+#define   HIER_INT_3_EN      BIT(3)
+#define   HIER_INT_4_EN      BIT(4)
+#define   HIER_INT_5_EN      BIT(5)
+#define   HIER_INT_6_EN      BIT(6)
+#define   HIER_INT_7_EN      BIT(7)
+
+#define   HIER_INT_EN_MSK \
+	 (HIER_INT_0_EN | HIER_INT_1_EN | HIER_INT_2_EN)
+
+
+/* SEC Memory Space IPC output payload.
+ *
+ * This register is part of the output payload which SEC provides to host.
+ */
+#define BRIDGE_IPC_OUTPUT_PAYLOAD_REG    0x20C0
+
+/* SeC Interrupt Cause Register - Host Aliveness Request
+ * This register is both an ICR to SeC and it is also exposed
+ * in the host-visible PCI memory space.
+ * The register is used by host to request SeC aliveness.
+ */
+#define SICR_HOST_ALIVENESS_REQ_REG      0x214C
+#define   SICR_HOST_ALIVENESS_REQ_REQUESTED    BIT(0)
+
+
+/* SeC Interrupt Cause Register - Host IPC Readiness
+ *
+ * This register is both an ICR to SeC and it is also exposed
+ * in the host-visible PCI memory space.
+ * This register is used by the host's SeC driver uses in order
+ * to synchronize with SeC about IPC interface state.
+ */
+#define SICR_HOST_IPC_READINESS_REQ_REG  0x2150
+
+
+#define SICR_HOST_IPC_READINESS_HOST_RDY  BIT(0)
+#define SICR_HOST_IPC_READINESS_SEC_RDY   BIT(1)
+#define SICR_HOST_IPC_READINESS_SYS_RDY     \
+	(SICR_HOST_IPC_READINESS_HOST_RDY | \
+	 SICR_HOST_IPC_READINESS_SEC_RDY)
+#define SICR_HOST_IPC_READINESS_RDY_CLR   BIT(2)
+
+/* SeC Interrupt Cause Register - SeC IPC Output Status
+ *
+ * This register indicates whether or not processing of the most recent
+ * command has been completed by the Host.
+ * New commands and payloads should not be written by SeC until this
+ * register indicates that the previous command has been processed.
+ */
+#define SICR_SEC_IPC_OUTPUT_STATUS_REG   0x2154
+#  define SEC_IPC_OUTPUT_STATUS_RDY BIT(0)
+
+
+
+/*  MEI IPC Message payload size 64 bytes */
+#define PAYLOAD_SIZE        64
+
+/* MAX size for SATT range 32MB */
+#define SATT_RANGE_MAX     (32 << 20)
+
+
+#endif /* _MEI_HW_TXE_REGS_H_ */
+