Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 301 insertions, 0 deletions

diff --git a/drivers/phy/intel/phy-intel-keembay-usb.c b/drivers/phy/intel/phy-intel-keembay-usb.c
new file mode 100644
index 000000000..c8b05f7b2
--- /dev/null
+++ b/drivers/phy/intel/phy-intel-keembay-usb.c
@@ -0,0 +1,301 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Intel Keem Bay USB PHY driver
+ * Copyright (C) 2020 Intel Corporation
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+/* USS (USB Subsystem) clock control registers */
+#define USS_CPR_CLK_EN		0x00
+#define USS_CPR_CLK_SET		0x04
+#define USS_CPR_CLK_CLR		0x08
+#define USS_CPR_RST_EN		0x10
+#define USS_CPR_RST_SET		0x14
+#define USS_CPR_RST_CLR		0x18
+
+/* USS clock/reset bit fields */
+#define USS_CPR_PHY_TST		BIT(6)
+#define USS_CPR_LOW_JIT		BIT(5)
+#define USS_CPR_CORE		BIT(4)
+#define USS_CPR_SUSPEND		BIT(3)
+#define USS_CPR_ALT_REF		BIT(2)
+#define USS_CPR_REF		BIT(1)
+#define USS_CPR_SYS		BIT(0)
+#define USS_CPR_MASK		GENMASK(6, 0)
+
+/* USS APB slave registers */
+#define USS_USB_CTRL_CFG0		0x10
+#define  VCC_RESET_N_MASK		BIT(31)
+
+#define USS_USB_PHY_CFG0		0x30
+#define  POR_MASK			BIT(15)
+#define  PHY_RESET_MASK			BIT(14)
+#define  PHY_REF_USE_PAD_MASK		BIT(5)
+
+#define USS_USB_PHY_CFG6		0x64
+#define  PHY0_SRAM_EXT_LD_DONE_MASK	BIT(23)
+
+#define USS_USB_PARALLEL_IF_CTRL	0xa0
+#define  USB_PHY_CR_PARA_SEL_MASK	BIT(2)
+
+#define USS_USB_TSET_SIGNALS_AND_GLOB	0xac
+#define  USB_PHY_CR_PARA_CLK_EN_MASK	BIT(7)
+
+#define USS_USB_STATUS_REG		0xb8
+#define  PHY0_SRAM_INIT_DONE_MASK	BIT(3)
+
+#define USS_USB_TIEOFFS_CONSTANTS_REG1	0xc0
+#define  IDDQ_ENABLE_MASK		BIT(10)
+
+struct keembay_usb_phy {
+	struct device *dev;
+	struct regmap *regmap_cpr;
+	struct regmap *regmap_slv;
+};
+
+static const struct regmap_config keembay_regmap_config = {
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.max_register = USS_USB_TIEOFFS_CONSTANTS_REG1,
+};
+
+static int keembay_usb_clocks_on(struct keembay_usb_phy *priv)
+{
+	int ret;
+
+	ret = regmap_update_bits(priv->regmap_cpr, USS_CPR_CLK_SET,
+				 USS_CPR_MASK, USS_CPR_MASK);
+	if (ret) {
+		dev_err(priv->dev, "error clock set: %d\n", ret);
+		return ret;
+	}
+
+	ret = regmap_update_bits(priv->regmap_cpr, USS_CPR_RST_SET,
+				 USS_CPR_MASK, USS_CPR_MASK);
+	if (ret) {
+		dev_err(priv->dev, "error reset set: %d\n", ret);
+		return ret;
+	}
+
+	ret = regmap_update_bits(priv->regmap_slv,
+				 USS_USB_TIEOFFS_CONSTANTS_REG1,
+				 IDDQ_ENABLE_MASK,
+				 FIELD_PREP(IDDQ_ENABLE_MASK, 0));
+	if (ret) {
+		dev_err(priv->dev, "error iddq disable: %d\n", ret);
+		return ret;
+	}
+
+	/* Wait 30us to ensure all analog blocks are powered up. */
+	usleep_range(30, 60);
+
+	ret = regmap_update_bits(priv->regmap_slv, USS_USB_PHY_CFG0,
+				 PHY_REF_USE_PAD_MASK,
+				 FIELD_PREP(PHY_REF_USE_PAD_MASK, 1));
+	if (ret)
+		dev_err(priv->dev, "error ref clock select: %d\n", ret);
+
+	return ret;
+}
+
+static int keembay_usb_core_off(struct keembay_usb_phy *priv)
+{
+	int ret;
+
+	ret = regmap_update_bits(priv->regmap_slv, USS_USB_CTRL_CFG0,
+				 VCC_RESET_N_MASK,
+				 FIELD_PREP(VCC_RESET_N_MASK, 0));
+	if (ret)
+		dev_err(priv->dev, "error core reset: %d\n", ret);
+
+	return ret;
+}
+
+static int keembay_usb_core_on(struct keembay_usb_phy *priv)
+{
+	int ret;
+
+	ret = regmap_update_bits(priv->regmap_slv, USS_USB_CTRL_CFG0,
+				 VCC_RESET_N_MASK,
+				 FIELD_PREP(VCC_RESET_N_MASK, 1));
+	if (ret)
+		dev_err(priv->dev, "error core on: %d\n", ret);
+
+	return ret;
+}
+
+static int keembay_usb_phys_on(struct keembay_usb_phy *priv)
+{
+	int ret;
+
+	ret = regmap_update_bits(priv->regmap_slv, USS_USB_PHY_CFG0,
+				 POR_MASK | PHY_RESET_MASK,
+				 FIELD_PREP(POR_MASK | PHY_RESET_MASK, 0));
+	if (ret)
+		dev_err(priv->dev, "error phys on: %d\n", ret);
+
+	return ret;
+}
+
+static int keembay_usb_phy_init(struct phy *phy)
+{
+	struct keembay_usb_phy *priv = phy_get_drvdata(phy);
+	u32 val;
+	int ret;
+
+	ret = keembay_usb_core_off(priv);
+	if (ret)
+		return ret;
+
+	/*
+	 * According to Keem Bay datasheet, wait minimum 20us after clock
+	 * enable before bringing PHYs out of reset.
+	 */
+	usleep_range(20, 40);
+
+	ret = keembay_usb_phys_on(priv);
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(priv->regmap_slv,
+				 USS_USB_TSET_SIGNALS_AND_GLOB,
+				 USB_PHY_CR_PARA_CLK_EN_MASK,
+				 FIELD_PREP(USB_PHY_CR_PARA_CLK_EN_MASK, 0));
+	if (ret) {
+		dev_err(priv->dev, "error cr clock disable: %d\n", ret);
+		return ret;
+	}
+
+	/*
+	 * According to Keem Bay datasheet, wait 2us after disabling the
+	 * clock into the USB 3.x parallel interface.
+	 */
+	udelay(2);
+
+	ret = regmap_update_bits(priv->regmap_slv,
+				 USS_USB_PARALLEL_IF_CTRL,
+				 USB_PHY_CR_PARA_SEL_MASK,
+				 FIELD_PREP(USB_PHY_CR_PARA_SEL_MASK, 1));
+	if (ret) {
+		dev_err(priv->dev, "error cr select: %d\n", ret);
+		return ret;
+	}
+
+	ret = regmap_update_bits(priv->regmap_slv,
+				 USS_USB_TSET_SIGNALS_AND_GLOB,
+				 USB_PHY_CR_PARA_CLK_EN_MASK,
+				 FIELD_PREP(USB_PHY_CR_PARA_CLK_EN_MASK, 1));
+	if (ret) {
+		dev_err(priv->dev, "error cr clock enable: %d\n", ret);
+		return ret;
+	}
+
+	ret = regmap_read_poll_timeout(priv->regmap_slv, USS_USB_STATUS_REG,
+				       val, val & PHY0_SRAM_INIT_DONE_MASK,
+				       USEC_PER_MSEC, 10 * USEC_PER_MSEC);
+	if (ret) {
+		dev_err(priv->dev, "SRAM init not done: %d\n", ret);
+		return ret;
+	}
+
+	ret = regmap_update_bits(priv->regmap_slv, USS_USB_PHY_CFG6,
+				 PHY0_SRAM_EXT_LD_DONE_MASK,
+				 FIELD_PREP(PHY0_SRAM_EXT_LD_DONE_MASK, 1));
+	if (ret) {
+		dev_err(priv->dev, "error SRAM init done set: %d\n", ret);
+		return ret;
+	}
+
+	/*
+	 * According to Keem Bay datasheet, wait 20us after setting the
+	 * SRAM load done bit, before releasing the controller reset.
+	 */
+	usleep_range(20, 40);
+
+	return keembay_usb_core_on(priv);
+}
+
+static const struct phy_ops ops = {
+	.init		= keembay_usb_phy_init,
+	.owner		= THIS_MODULE,
+};
+
+static int keembay_usb_phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct keembay_usb_phy *priv;
+	struct phy *generic_phy;
+	struct phy_provider *phy_provider;
+	void __iomem *base;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	base = devm_platform_ioremap_resource_byname(pdev, "cpr-apb-base");
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	priv->regmap_cpr = devm_regmap_init_mmio(dev, base,
+						 &keembay_regmap_config);
+	if (IS_ERR(priv->regmap_cpr))
+		return PTR_ERR(priv->regmap_cpr);
+
+	base = devm_platform_ioremap_resource_byname(pdev, "slv-apb-base");
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	priv->regmap_slv = devm_regmap_init_mmio(dev, base,
+						 &keembay_regmap_config);
+	if (IS_ERR(priv->regmap_slv))
+		return PTR_ERR(priv->regmap_slv);
+
+	generic_phy = devm_phy_create(dev, dev->of_node, &ops);
+	if (IS_ERR(generic_phy))
+		return dev_err_probe(dev, PTR_ERR(generic_phy),
+				     "failed to create PHY\n");
+
+	phy_set_drvdata(generic_phy, priv);
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (IS_ERR(phy_provider))
+		return dev_err_probe(dev, PTR_ERR(phy_provider),
+				     "failed to register phy provider\n");
+
+	/* Setup USB subsystem clocks */
+	ret = keembay_usb_clocks_on(priv);
+	if (ret)
+		return ret;
+
+	/* and turn on the DWC3 core, prior to DWC3 driver init. */
+	return keembay_usb_core_on(priv);
+}
+
+static const struct of_device_id keembay_usb_phy_dt_ids[] = {
+	{ .compatible = "intel,keembay-usb-phy" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, keembay_usb_phy_dt_ids);
+
+static struct platform_driver keembay_usb_phy_driver = {
+	.probe		= keembay_usb_phy_probe,
+	.driver		= {
+		.name	= "keembay-usb-phy",
+		.of_match_table = keembay_usb_phy_dt_ids,
+	},
+};
+module_platform_driver(keembay_usb_phy_driver);
+
+MODULE_AUTHOR("Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>");
+MODULE_DESCRIPTION("Intel Keem Bay USB PHY driver");
+MODULE_LICENSE("GPL v2");