Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 1938 insertions, 0 deletions

diff --git a/drivers/tty/mxser.c b/drivers/tty/mxser.c
new file mode 100644
index 000000000..2436e0b10
--- /dev/null
+++ b/drivers/tty/mxser.c
@@ -0,0 +1,1938 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ *          mxser.c  -- MOXA Smartio/Industio family multiport serial driver.
+ *
+ *      Copyright (C) 1999-2006  Moxa Technologies (support@moxa.com).
+ *	Copyright (C) 2006-2008  Jiri Slaby <jirislaby@gmail.com>
+ *
+ *      This code is loosely based on the 1.8 moxa driver which is based on
+ *	Linux serial driver, written by Linus Torvalds, Theodore T'so and
+ *	others.
+ *
+ *	Fed through a cleanup, indent and remove of non 2.6 code by Alan Cox
+ *	<alan@lxorguk.ukuu.org.uk>. The original 1.8 code is available on
+ *	www.moxa.com.
+ *	- Fixed x86_64 cleanness
+ */
+
+#include <linux/module.h>
+#include <linux/errno.h>
+#include <linux/signal.h>
+#include <linux/sched.h>
+#include <linux/timer.h>
+#include <linux/interrupt.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial.h>
+#include <linux/serial_reg.h>
+#include <linux/major.h>
+#include <linux/string.h>
+#include <linux/fcntl.h>
+#include <linux/ptrace.h>
+#include <linux/ioport.h>
+#include <linux/mm.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+#include <linux/bitops.h>
+#include <linux/slab.h>
+#include <linux/ratelimit.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <linux/uaccess.h>
+
+/*
+ *	Semi-public control interfaces
+ */
+
+/*
+ *	MOXA ioctls
+ */
+
+#define MOXA			0x400
+#define MOXA_SET_OP_MODE	(MOXA + 66)
+#define MOXA_GET_OP_MODE	(MOXA + 67)
+
+#define RS232_MODE		0
+#define RS485_2WIRE_MODE	1
+#define RS422_MODE		2
+#define RS485_4WIRE_MODE	3
+#define OP_MODE_MASK		3
+
+/* --------------------------------------------------- */
+
+/*
+ * Follow just what Moxa Must chip defines.
+ *
+ * When LCR register (offset 0x03) is written the following value, the Must chip
+ * will enter enhanced mode. And a write to EFR (offset 0x02) bit 6,7 will
+ * change bank.
+ */
+#define MOXA_MUST_ENTER_ENHANCED	0xBF
+
+/* when enhanced mode is enabled, access to general bank register */
+#define MOXA_MUST_GDL_REGISTER		0x07
+#define MOXA_MUST_GDL_MASK		0x7F
+#define MOXA_MUST_GDL_HAS_BAD_DATA	0x80
+
+#define MOXA_MUST_LSR_RERR		0x80	/* error in receive FIFO */
+/* enhanced register bank select and enhanced mode setting register */
+/* This works only when LCR register equals to 0xBF */
+#define MOXA_MUST_EFR_REGISTER		0x02
+#define MOXA_MUST_EFR_EFRB_ENABLE	0x10 /* enhanced mode enable */
+/* enhanced register bank set 0, 1, 2 */
+#define MOXA_MUST_EFR_BANK0		0x00
+#define MOXA_MUST_EFR_BANK1		0x40
+#define MOXA_MUST_EFR_BANK2		0x80
+#define MOXA_MUST_EFR_BANK3		0xC0
+#define MOXA_MUST_EFR_BANK_MASK		0xC0
+
+/* set XON1 value register, when LCR=0xBF and change to bank0 */
+#define MOXA_MUST_XON1_REGISTER		0x04
+
+/* set XON2 value register, when LCR=0xBF and change to bank0 */
+#define MOXA_MUST_XON2_REGISTER		0x05
+
+/* set XOFF1 value register, when LCR=0xBF and change to bank0 */
+#define MOXA_MUST_XOFF1_REGISTER	0x06
+
+/* set XOFF2 value register, when LCR=0xBF and change to bank0 */
+#define MOXA_MUST_XOFF2_REGISTER	0x07
+
+#define MOXA_MUST_RBRTL_REGISTER	0x04
+#define MOXA_MUST_RBRTH_REGISTER	0x05
+#define MOXA_MUST_RBRTI_REGISTER	0x06
+#define MOXA_MUST_THRTL_REGISTER	0x07
+#define MOXA_MUST_ENUM_REGISTER		0x04
+#define MOXA_MUST_HWID_REGISTER		0x05
+#define MOXA_MUST_ECR_REGISTER		0x06
+#define MOXA_MUST_CSR_REGISTER		0x07
+
+#define MOXA_MUST_FCR_GDA_MODE_ENABLE	0x20 /* good data mode enable */
+#define MOXA_MUST_FCR_GDA_ONLY_ENABLE	0x10 /* only good data put into RxFIFO */
+
+#define MOXA_MUST_IER_ECTSI		0x80 /* enable CTS interrupt */
+#define MOXA_MUST_IER_ERTSI		0x40 /* enable RTS interrupt */
+#define MOXA_MUST_IER_XINT		0x20 /* enable Xon/Xoff interrupt */
+#define MOXA_MUST_IER_EGDAI		0x10 /* enable GDA interrupt */
+
+#define MOXA_MUST_RECV_ISR		(UART_IER_RDI | MOXA_MUST_IER_EGDAI)
+
+/* GDA interrupt pending */
+#define MOXA_MUST_IIR_GDA		0x1C
+#define MOXA_MUST_IIR_RDA		0x04
+#define MOXA_MUST_IIR_RTO		0x0C
+#define MOXA_MUST_IIR_LSR		0x06
+
+/* received Xon/Xoff or specical interrupt pending */
+#define MOXA_MUST_IIR_XSC		0x10
+
+/* RTS/CTS change state interrupt pending */
+#define MOXA_MUST_IIR_RTSCTS		0x20
+#define MOXA_MUST_IIR_MASK		0x3E
+
+#define MOXA_MUST_MCR_XON_FLAG		0x40
+#define MOXA_MUST_MCR_XON_ANY		0x80
+#define MOXA_MUST_MCR_TX_XON		0x08
+
+#define MOXA_MUST_EFR_SF_MASK		0x0F /* software flow control on chip mask value */
+#define MOXA_MUST_EFR_SF_TX1		0x08 /* send Xon1/Xoff1 */
+#define MOXA_MUST_EFR_SF_TX2		0x04 /* send Xon2/Xoff2 */
+#define MOXA_MUST_EFR_SF_TX12		0x0C /* send Xon1,Xon2/Xoff1,Xoff2 */
+#define MOXA_MUST_EFR_SF_TX_NO		0x00 /* don't send Xon/Xoff */
+#define MOXA_MUST_EFR_SF_TX_MASK	0x0C /* Tx software flow control mask */
+#define MOXA_MUST_EFR_SF_RX_NO		0x00 /* don't receive Xon/Xoff */
+#define MOXA_MUST_EFR_SF_RX1		0x02 /* receive Xon1/Xoff1 */
+#define MOXA_MUST_EFR_SF_RX2		0x01 /* receive Xon2/Xoff2 */
+#define MOXA_MUST_EFR_SF_RX12		0x03 /* receive Xon1,Xon2/Xoff1,Xoff2 */
+#define MOXA_MUST_EFR_SF_RX_MASK	0x03 /* Rx software flow control mask */
+
+#define	MXSERMAJOR	 174
+
+#define MXSER_BOARDS		4	/* Max. boards */
+#define MXSER_PORTS_PER_BOARD	8	/* Max. ports per board */
+#define MXSER_PORTS		(MXSER_BOARDS * MXSER_PORTS_PER_BOARD)
+#define MXSER_ISR_PASS_LIMIT	100
+
+#define WAKEUP_CHARS		256
+
+#define MXSER_BAUD_BASE		921600
+#define MXSER_CUSTOM_DIVISOR	(MXSER_BAUD_BASE * 16)
+
+#define PCI_DEVICE_ID_MOXA_RC7000	0x0001
+#define PCI_DEVICE_ID_MOXA_CP102	0x1020
+#define PCI_DEVICE_ID_MOXA_CP102UL	0x1021
+#define PCI_DEVICE_ID_MOXA_CP102U	0x1022
+#define PCI_DEVICE_ID_MOXA_CP102UF	0x1023
+#define PCI_DEVICE_ID_MOXA_C104		0x1040
+#define PCI_DEVICE_ID_MOXA_CP104U	0x1041
+#define PCI_DEVICE_ID_MOXA_CP104JU	0x1042
+#define PCI_DEVICE_ID_MOXA_CP104EL	0x1043
+#define PCI_DEVICE_ID_MOXA_POS104UL	0x1044
+#define PCI_DEVICE_ID_MOXA_CB108	0x1080
+#define PCI_DEVICE_ID_MOXA_CP112UL	0x1120
+#define PCI_DEVICE_ID_MOXA_CT114	0x1140
+#define PCI_DEVICE_ID_MOXA_CP114	0x1141
+#define PCI_DEVICE_ID_MOXA_CB114	0x1142
+#define PCI_DEVICE_ID_MOXA_CP114UL	0x1143
+#define PCI_DEVICE_ID_MOXA_CP118U	0x1180
+#define PCI_DEVICE_ID_MOXA_CP118EL	0x1181
+#define PCI_DEVICE_ID_MOXA_CP132	0x1320
+#define PCI_DEVICE_ID_MOXA_CP132U	0x1321
+#define PCI_DEVICE_ID_MOXA_CP134U	0x1340
+#define PCI_DEVICE_ID_MOXA_CB134I	0x1341
+#define PCI_DEVICE_ID_MOXA_CP138U	0x1380
+#define PCI_DEVICE_ID_MOXA_C168		0x1680
+#define PCI_DEVICE_ID_MOXA_CP168U	0x1681
+#define PCI_DEVICE_ID_MOXA_CP168EL	0x1682
+
+#define MXSER_NPORTS(ddata)		((ddata) & 0xffU)
+#define MXSER_HIGHBAUD			0x0100
+
+enum mxser_must_hwid {
+	MOXA_OTHER_UART		= 0x00,
+	MOXA_MUST_MU150_HWID	= 0x01,
+	MOXA_MUST_MU860_HWID	= 0x02,
+};
+
+static const struct {
+	u8 type;
+	u8 fifo_size;
+	u8 rx_high_water;
+	u8 rx_low_water;
+	speed_t max_baud;
+} Gpci_uart_info[] = {
+	{ MOXA_OTHER_UART,	 16, 14,  1, 921600 },
+	{ MOXA_MUST_MU150_HWID,	 64, 48, 16, 230400 },
+	{ MOXA_MUST_MU860_HWID, 128, 96, 32, 921600 }
+};
+#define UART_INFO_NUM	ARRAY_SIZE(Gpci_uart_info)
+
+
+/* driver_data correspond to the lines in the structure above
+   see also ISA probe function before you change something */
+static const struct pci_device_id mxser_pcibrds[] = {
+	{ PCI_DEVICE_DATA(MOXA, C168,		8) },
+	{ PCI_DEVICE_DATA(MOXA, C104,		4) },
+	{ PCI_DEVICE_DATA(MOXA, CP132,		2) },
+	{ PCI_DEVICE_DATA(MOXA, CP114,		4) },
+	{ PCI_DEVICE_DATA(MOXA, CT114,		4) },
+	{ PCI_DEVICE_DATA(MOXA, CP102,		2 | MXSER_HIGHBAUD) },
+	{ PCI_DEVICE_DATA(MOXA, CP104U,		4) },
+	{ PCI_DEVICE_DATA(MOXA, CP168U,		8) },
+	{ PCI_DEVICE_DATA(MOXA, CP132U,		2) },
+	{ PCI_DEVICE_DATA(MOXA, CP134U,		4) },
+	{ PCI_DEVICE_DATA(MOXA, CP104JU,	4) },
+	{ PCI_DEVICE_DATA(MOXA, RC7000,		8) }, /* RC7000 */
+	{ PCI_DEVICE_DATA(MOXA, CP118U,		8) },
+	{ PCI_DEVICE_DATA(MOXA, CP102UL,	2) },
+	{ PCI_DEVICE_DATA(MOXA, CP102U,		2) },
+	{ PCI_DEVICE_DATA(MOXA, CP118EL,	8) },
+	{ PCI_DEVICE_DATA(MOXA, CP168EL,	8) },
+	{ PCI_DEVICE_DATA(MOXA, CP104EL,	4) },
+	{ PCI_DEVICE_DATA(MOXA, CB108,		8) },
+	{ PCI_DEVICE_DATA(MOXA, CB114,		4) },
+	{ PCI_DEVICE_DATA(MOXA, CB134I,		4) },
+	{ PCI_DEVICE_DATA(MOXA, CP138U,		8) },
+	{ PCI_DEVICE_DATA(MOXA, POS104UL,	4) },
+	{ PCI_DEVICE_DATA(MOXA, CP114UL,	4) },
+	{ PCI_DEVICE_DATA(MOXA, CP102UF,	2) },
+	{ PCI_DEVICE_DATA(MOXA, CP112UL,	2) },
+	{ }
+};
+MODULE_DEVICE_TABLE(pci, mxser_pcibrds);
+
+static int ttymajor = MXSERMAJOR;
+
+/* Variables for insmod */
+
+MODULE_AUTHOR("Casper Yang");
+MODULE_DESCRIPTION("MOXA Smartio/Industio Family Multiport Board Device Driver");
+module_param(ttymajor, int, 0);
+MODULE_LICENSE("GPL");
+
+struct mxser_board;
+
+struct mxser_port {
+	struct tty_port port;
+	struct mxser_board *board;
+
+	unsigned long ioaddr;
+	unsigned long opmode_ioaddr;
+
+	u8 rx_high_water;
+	u8 rx_low_water;
+	int type;		/* UART type */
+
+	unsigned char x_char;	/* xon/xoff character */
+	u8 IER;			/* Interrupt Enable Register */
+	u8 MCR;			/* Modem control register */
+	u8 FCR;			/* FIFO control register */
+
+	struct async_icount icount; /* kernel counters for 4 input interrupts */
+	unsigned int timeout;
+
+	u8 read_status_mask;
+	u8 ignore_status_mask;
+	u8 xmit_fifo_size;
+
+	spinlock_t slock;
+};
+
+struct mxser_board {
+	unsigned int idx;
+	unsigned short nports;
+	int irq;
+	unsigned long vector;
+
+	enum mxser_must_hwid must_hwid;
+	speed_t max_baud;
+
+	struct mxser_port ports[];
+};
+
+static DECLARE_BITMAP(mxser_boards, MXSER_BOARDS);
+static struct tty_driver *mxvar_sdriver;
+
+static u8 __mxser_must_set_EFR(unsigned long baseio, u8 clear, u8 set,
+		bool restore_LCR)
+{
+	u8 oldlcr, efr;
+
+	oldlcr = inb(baseio + UART_LCR);
+	outb(MOXA_MUST_ENTER_ENHANCED, baseio + UART_LCR);
+
+	efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
+	efr &= ~clear;
+	efr |= set;
+
+	outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
+
+	if (restore_LCR)
+		outb(oldlcr, baseio + UART_LCR);
+
+	return oldlcr;
+}
+
+static u8 mxser_must_select_bank(unsigned long baseio, u8 bank)
+{
+	return __mxser_must_set_EFR(baseio, MOXA_MUST_EFR_BANK_MASK, bank,
+			false);
+}
+
+static void mxser_set_must_xon1_value(unsigned long baseio, u8 value)
+{
+	u8 oldlcr = mxser_must_select_bank(baseio, MOXA_MUST_EFR_BANK0);
+	outb(value, baseio + MOXA_MUST_XON1_REGISTER);
+	outb(oldlcr, baseio + UART_LCR);
+}
+
+static void mxser_set_must_xoff1_value(unsigned long baseio, u8 value)
+{
+	u8 oldlcr = mxser_must_select_bank(baseio, MOXA_MUST_EFR_BANK0);
+	outb(value, baseio + MOXA_MUST_XOFF1_REGISTER);
+	outb(oldlcr, baseio + UART_LCR);
+}
+
+static void mxser_set_must_fifo_value(struct mxser_port *info)
+{
+	u8 oldlcr = mxser_must_select_bank(info->ioaddr, MOXA_MUST_EFR_BANK1);
+	outb(info->rx_high_water, info->ioaddr + MOXA_MUST_RBRTH_REGISTER);
+	outb(info->rx_high_water, info->ioaddr + MOXA_MUST_RBRTI_REGISTER);
+	outb(info->rx_low_water, info->ioaddr + MOXA_MUST_RBRTL_REGISTER);
+	outb(oldlcr, info->ioaddr + UART_LCR);
+}
+
+static void mxser_set_must_enum_value(unsigned long baseio, u8 value)
+{
+	u8 oldlcr = mxser_must_select_bank(baseio, MOXA_MUST_EFR_BANK2);
+	outb(value, baseio + MOXA_MUST_ENUM_REGISTER);
+	outb(oldlcr, baseio + UART_LCR);
+}
+
+static u8 mxser_get_must_hardware_id(unsigned long baseio)
+{
+	u8 oldlcr = mxser_must_select_bank(baseio, MOXA_MUST_EFR_BANK2);
+	u8 id = inb(baseio + MOXA_MUST_HWID_REGISTER);
+	outb(oldlcr, baseio + UART_LCR);
+
+	return id;
+}
+
+static void mxser_must_set_EFR(unsigned long baseio, u8 clear, u8 set)
+{
+	__mxser_must_set_EFR(baseio, clear, set, true);
+}
+
+static void mxser_must_set_enhance_mode(unsigned long baseio, bool enable)
+{
+	mxser_must_set_EFR(baseio,
+			enable ? 0 : MOXA_MUST_EFR_EFRB_ENABLE,
+			enable ? MOXA_MUST_EFR_EFRB_ENABLE : 0);
+}
+
+static void mxser_must_no_sw_flow_control(unsigned long baseio)
+{
+	mxser_must_set_EFR(baseio, MOXA_MUST_EFR_SF_MASK, 0);
+}
+
+static void mxser_must_set_tx_sw_flow_control(unsigned long baseio, bool enable)
+{
+	mxser_must_set_EFR(baseio, MOXA_MUST_EFR_SF_TX_MASK,
+			enable ? MOXA_MUST_EFR_SF_TX1 : 0);
+}
+
+static void mxser_must_set_rx_sw_flow_control(unsigned long baseio, bool enable)
+{
+	mxser_must_set_EFR(baseio, MOXA_MUST_EFR_SF_RX_MASK,
+			enable ? MOXA_MUST_EFR_SF_RX1 : 0);
+}
+
+static enum mxser_must_hwid mxser_must_get_hwid(unsigned long io)
+{
+	u8 oldmcr, hwid;
+	int i;
+
+	outb(0, io + UART_LCR);
+	mxser_must_set_enhance_mode(io, false);
+	oldmcr = inb(io + UART_MCR);
+	outb(0, io + UART_MCR);
+	mxser_set_must_xon1_value(io, 0x11);
+	if (inb(io + UART_MCR) != 0) {
+		outb(oldmcr, io + UART_MCR);
+		return MOXA_OTHER_UART;
+	}
+
+	hwid = mxser_get_must_hardware_id(io);
+	for (i = 1; i < UART_INFO_NUM; i++) /* 0 = OTHER_UART */
+		if (hwid == Gpci_uart_info[i].type)
+			return hwid;
+
+	return MOXA_OTHER_UART;
+}
+
+static bool mxser_16550A_or_MUST(struct mxser_port *info)
+{
+	return info->type == PORT_16550A || info->board->must_hwid;
+}
+
+static void mxser_process_txrx_fifo(struct mxser_port *info)
+{
+	unsigned int i;
+
+	if (info->type == PORT_16450 || info->type == PORT_8250) {
+		info->rx_high_water = 1;
+		info->rx_low_water = 1;
+		info->xmit_fifo_size = 1;
+		return;
+	}
+
+	for (i = 0; i < UART_INFO_NUM; i++)
+		if (info->board->must_hwid == Gpci_uart_info[i].type) {
+			info->rx_low_water = Gpci_uart_info[i].rx_low_water;
+			info->rx_high_water = Gpci_uart_info[i].rx_high_water;
+			info->xmit_fifo_size = Gpci_uart_info[i].fifo_size;
+			break;
+		}
+}
+
+static void __mxser_start_tx(struct mxser_port *info)
+{
+	outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER);
+	info->IER |= UART_IER_THRI;
+	outb(info->IER, info->ioaddr + UART_IER);
+}
+
+static void mxser_start_tx(struct mxser_port *info)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&info->slock, flags);
+	__mxser_start_tx(info);
+	spin_unlock_irqrestore(&info->slock, flags);
+}
+
+static void __mxser_stop_tx(struct mxser_port *info)
+{
+	info->IER &= ~UART_IER_THRI;
+	outb(info->IER, info->ioaddr + UART_IER);
+}
+
+static int mxser_carrier_raised(struct tty_port *port)
+{
+	struct mxser_port *mp = container_of(port, struct mxser_port, port);
+	return (inb(mp->ioaddr + UART_MSR) & UART_MSR_DCD)?1:0;
+}
+
+static void mxser_dtr_rts(struct tty_port *port, int on)
+{
+	struct mxser_port *mp = container_of(port, struct mxser_port, port);
+	unsigned long flags;
+	u8 mcr;
+
+	spin_lock_irqsave(&mp->slock, flags);
+	mcr = inb(mp->ioaddr + UART_MCR);
+	if (on)
+		mcr |= UART_MCR_DTR | UART_MCR_RTS;
+	else
+		mcr &= ~(UART_MCR_DTR | UART_MCR_RTS);
+	outb(mcr, mp->ioaddr + UART_MCR);
+	spin_unlock_irqrestore(&mp->slock, flags);
+}
+
+static int mxser_set_baud(struct tty_struct *tty, speed_t newspd)
+{
+	struct mxser_port *info = tty->driver_data;
+	unsigned int quot = 0, baud;
+	unsigned char cval;
+	u64 timeout;
+
+	if (newspd > info->board->max_baud)
+		return -1;
+
+	if (newspd == 134) {
+		quot = 2 * MXSER_BAUD_BASE / 269;
+		tty_encode_baud_rate(tty, 134, 134);
+	} else if (newspd) {
+		quot = MXSER_BAUD_BASE / newspd;
+		if (quot == 0)
+			quot = 1;
+		baud = MXSER_BAUD_BASE / quot;
+		tty_encode_baud_rate(tty, baud, baud);
+	} else {
+		quot = 0;
+	}
+
+	/*
+	 * worst case (128 * 1000 * 10 * 18432) needs 35 bits, so divide in the
+	 * u64 domain
+	 */
+	timeout = (u64)info->xmit_fifo_size * HZ * 10 * quot;
+	do_div(timeout, MXSER_BAUD_BASE);
+	info->timeout = timeout + HZ / 50; /* Add .02 seconds of slop */
+
+	if (quot) {
+		info->MCR |= UART_MCR_DTR;
+		outb(info->MCR, info->ioaddr + UART_MCR);
+	} else {
+		info->MCR &= ~UART_MCR_DTR;
+		outb(info->MCR, info->ioaddr + UART_MCR);
+		return 0;
+	}
+
+	cval = inb(info->ioaddr + UART_LCR);
+
+	outb(cval | UART_LCR_DLAB, info->ioaddr + UART_LCR);	/* set DLAB */
+
+	outb(quot & 0xff, info->ioaddr + UART_DLL);	/* LS of divisor */
+	outb(quot >> 8, info->ioaddr + UART_DLM);	/* MS of divisor */
+	outb(cval, info->ioaddr + UART_LCR);	/* reset DLAB */
+
+	if (C_BAUD(tty) == BOTHER) {
+		quot = MXSER_BAUD_BASE % newspd;
+		quot *= 8;
+		if (quot % newspd > newspd / 2) {
+			quot /= newspd;
+			quot++;
+		} else
+			quot /= newspd;
+
+		mxser_set_must_enum_value(info->ioaddr, quot);
+	} else {
+		mxser_set_must_enum_value(info->ioaddr, 0);
+	}
+
+	return 0;
+}
+
+static void mxser_handle_cts(struct tty_struct *tty, struct mxser_port *info,
+		u8 msr)
+{
+	bool cts = msr & UART_MSR_CTS;
+
+	if (tty->hw_stopped) {
+		if (cts) {
+			tty->hw_stopped = 0;
+
+			if (!mxser_16550A_or_MUST(info))
+				__mxser_start_tx(info);
+			tty_wakeup(tty);
+		}
+		return;
+	} else if (cts)
+		return;
+
+	tty->hw_stopped = 1;
+	if (!mxser_16550A_or_MUST(info))
+		__mxser_stop_tx(info);
+}
+
+/*
+ * This routine is called to set the UART divisor registers to match
+ * the specified baud rate for a serial port.
+ */
+static void mxser_change_speed(struct tty_struct *tty,
+			       const struct ktermios *old_termios)
+{
+	struct mxser_port *info = tty->driver_data;
+	unsigned cflag, cval;
+
+	cflag = tty->termios.c_cflag;
+
+	if (mxser_set_baud(tty, tty_get_baud_rate(tty))) {
+		/* Use previous rate on a failure */
+		if (old_termios) {
+			speed_t baud = tty_termios_baud_rate(old_termios);
+			tty_encode_baud_rate(tty, baud, baud);
+		}
+	}
+
+	/* byte size and parity */
+	cval = UART_LCR_WLEN(tty_get_char_size(tty->termios.c_cflag));
+
+	if (cflag & CSTOPB)
+		cval |= UART_LCR_STOP;
+	if (cflag & PARENB)
+		cval |= UART_LCR_PARITY;
+	if (!(cflag & PARODD))
+		cval |= UART_LCR_EPAR;
+	if (cflag & CMSPAR)
+		cval |= UART_LCR_SPAR;
+
+	info->FCR = 0;
+	if (info->board->must_hwid) {
+		info->FCR |= UART_FCR_ENABLE_FIFO |
+			MOXA_MUST_FCR_GDA_MODE_ENABLE;
+		mxser_set_must_fifo_value(info);
+	} else if (info->type != PORT_8250 && info->type != PORT_16450) {
+		info->FCR |= UART_FCR_ENABLE_FIFO;
+		switch (info->rx_high_water) {
+		case 1:
+			info->FCR |= UART_FCR_TRIGGER_1;
+			break;
+		case 4:
+			info->FCR |= UART_FCR_TRIGGER_4;
+			break;
+		case 8:
+			info->FCR |= UART_FCR_TRIGGER_8;
+			break;
+		default:
+			info->FCR |= UART_FCR_TRIGGER_14;
+			break;
+		}
+	}
+
+	/* CTS flow control flag and modem status interrupts */
+	info->IER &= ~UART_IER_MSI;
+	info->MCR &= ~UART_MCR_AFE;
+	tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
+	if (cflag & CRTSCTS) {
+		info->IER |= UART_IER_MSI;
+		if (mxser_16550A_or_MUST(info)) {
+			info->MCR |= UART_MCR_AFE;
+		} else {
+			mxser_handle_cts(tty, info,
+					inb(info->ioaddr + UART_MSR));
+		}
+	}
+	outb(info->MCR, info->ioaddr + UART_MCR);
+	tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
+	if (~cflag & CLOCAL)
+		info->IER |= UART_IER_MSI;
+	outb(info->IER, info->ioaddr + UART_IER);
+
+	/*
+	 * Set up parity check flag
+	 */
+	info->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
+	if (I_INPCK(tty))
+		info->read_status_mask |= UART_LSR_FE | UART_LSR_PE;
+	if (I_BRKINT(tty) || I_PARMRK(tty))
+		info->read_status_mask |= UART_LSR_BI;
+
+	info->ignore_status_mask = 0;
+
+	if (I_IGNBRK(tty)) {
+		info->ignore_status_mask |= UART_LSR_BI;
+		info->read_status_mask |= UART_LSR_BI;
+		/*
+		 * If we're ignore parity and break indicators, ignore
+		 * overruns too.  (For real raw support).
+		 */
+		if (I_IGNPAR(tty)) {
+			info->ignore_status_mask |=
+						UART_LSR_OE |
+						UART_LSR_PE |
+						UART_LSR_FE;
+			info->read_status_mask |=
+						UART_LSR_OE |
+						UART_LSR_PE |
+						UART_LSR_FE;
+		}
+	}
+	if (info->board->must_hwid) {
+		mxser_set_must_xon1_value(info->ioaddr, START_CHAR(tty));
+		mxser_set_must_xoff1_value(info->ioaddr, STOP_CHAR(tty));
+		mxser_must_set_rx_sw_flow_control(info->ioaddr, I_IXON(tty));
+		mxser_must_set_tx_sw_flow_control(info->ioaddr, I_IXOFF(tty));
+	}
+
+
+	outb(info->FCR, info->ioaddr + UART_FCR);
+	outb(cval, info->ioaddr + UART_LCR);
+}
+
+static u8 mxser_check_modem_status(struct tty_struct *tty,
+				struct mxser_port *port)
+{
+	u8 msr = inb(port->ioaddr + UART_MSR);
+
+	if (!(msr & UART_MSR_ANY_DELTA))
+		return msr;
+
+	/* update input line counters */
+	if (msr & UART_MSR_TERI)
+		port->icount.rng++;
+	if (msr & UART_MSR_DDSR)
+		port->icount.dsr++;
+	if (msr & UART_MSR_DDCD)
+		port->icount.dcd++;
+	if (msr & UART_MSR_DCTS)
+		port->icount.cts++;
+	wake_up_interruptible(&port->port.delta_msr_wait);
+
+	if (tty_port_check_carrier(&port->port) && (msr & UART_MSR_DDCD)) {
+		if (msr & UART_MSR_DCD)
+			wake_up_interruptible(&port->port.open_wait);
+	}
+
+	if (tty_port_cts_enabled(&port->port))
+		mxser_handle_cts(tty, port, msr);
+
+	return msr;
+}
+
+static void mxser_disable_and_clear_FIFO(struct mxser_port *info)
+{
+	u8 fcr = UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT;
+
+	if (info->board->must_hwid)
+		fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE;
+
+	outb(fcr, info->ioaddr + UART_FCR);
+}
+
+static int mxser_activate(struct tty_port *port, struct tty_struct *tty)
+{
+	struct mxser_port *info = container_of(port, struct mxser_port, port);
+	unsigned long flags;
+	int ret;
+
+	ret = tty_port_alloc_xmit_buf(port);
+	if (ret < 0)
+		return ret;
+
+	spin_lock_irqsave(&info->slock, flags);
+
+	if (!info->type) {
+		set_bit(TTY_IO_ERROR, &tty->flags);
+		spin_unlock_irqrestore(&info->slock, flags);
+		ret = 0;
+		goto err_free_xmit;
+	}
+
+	/*
+	 * Clear the FIFO buffers and disable them
+	 * (they will be reenabled in mxser_change_speed())
+	 */
+	mxser_disable_and_clear_FIFO(info);
+
+	/*
+	 * At this point there's no way the LSR could still be 0xFF;
+	 * if it is, then bail out, because there's likely no UART
+	 * here.
+	 */
+	if (inb(info->ioaddr + UART_LSR) == 0xff) {
+		spin_unlock_irqrestore(&info->slock, flags);
+		if (capable(CAP_SYS_ADMIN)) {
+			set_bit(TTY_IO_ERROR, &tty->flags);
+			return 0;
+		}
+
+		ret = -ENODEV;
+		goto err_free_xmit;
+	}
+
+	/*
+	 * Clear the interrupt registers.
+	 */
+	(void) inb(info->ioaddr + UART_LSR);
+	(void) inb(info->ioaddr + UART_RX);
+	(void) inb(info->ioaddr + UART_IIR);
+	(void) inb(info->ioaddr + UART_MSR);
+
+	/*
+	 * Now, initialize the UART
+	 */
+	outb(UART_LCR_WLEN8, info->ioaddr + UART_LCR);	/* reset DLAB */
+	info->MCR = UART_MCR_DTR | UART_MCR_RTS;
+	outb(info->MCR, info->ioaddr + UART_MCR);
+
+	/*
+	 * Finally, enable interrupts
+	 */
+	info->IER = UART_IER_MSI | UART_IER_RLSI | UART_IER_RDI;
+
+	if (info->board->must_hwid)
+		info->IER |= MOXA_MUST_IER_EGDAI;
+	outb(info->IER, info->ioaddr + UART_IER);	/* enable interrupts */
+
+	/*
+	 * And clear the interrupt registers again for luck.
+	 */
+	(void) inb(info->ioaddr + UART_LSR);
+	(void) inb(info->ioaddr + UART_RX);
+	(void) inb(info->ioaddr + UART_IIR);
+	(void) inb(info->ioaddr + UART_MSR);
+
+	clear_bit(TTY_IO_ERROR, &tty->flags);
+	kfifo_reset(&port->xmit_fifo);
+
+	/*
+	 * and set the speed of the serial port
+	 */
+	mxser_change_speed(tty, NULL);
+	spin_unlock_irqrestore(&info->slock, flags);
+
+	return 0;
+err_free_xmit:
+	tty_port_free_xmit_buf(port);
+	return ret;
+}
+
+/*
+ * To stop accepting input, we disable the receive line status interrupts, and
+ * tell the interrupt driver to stop checking the data ready bit in the line
+ * status register.
+ */
+static void mxser_stop_rx(struct mxser_port *info)
+{
+	info->IER &= ~UART_IER_RLSI;
+	if (info->board->must_hwid)
+		info->IER &= ~MOXA_MUST_RECV_ISR;
+
+	outb(info->IER, info->ioaddr + UART_IER);
+}
+
+/*
+ * This routine will shutdown a serial port
+ */
+static void mxser_shutdown_port(struct tty_port *port)
+{
+	struct mxser_port *info = container_of(port, struct mxser_port, port);
+	unsigned long flags;
+
+	spin_lock_irqsave(&info->slock, flags);
+
+	mxser_stop_rx(info);
+
+	/*
+	 * clear delta_msr_wait queue to avoid mem leaks: we may free the irq
+	 * here so the queue might never be waken up
+	 */
+	wake_up_interruptible(&info->port.delta_msr_wait);
+
+	info->IER = 0;
+	outb(0x00, info->ioaddr + UART_IER);
+
+	/* clear Rx/Tx FIFO's */
+	mxser_disable_and_clear_FIFO(info);
+
+	/* read data port to reset things */
+	(void) inb(info->ioaddr + UART_RX);
+
+
+	if (info->board->must_hwid)
+		mxser_must_no_sw_flow_control(info->ioaddr);
+
+	spin_unlock_irqrestore(&info->slock, flags);
+
+	/* make sure ISR is not running while we free the buffer */
+	synchronize_irq(info->board->irq);
+
+	tty_port_free_xmit_buf(port);
+}
+
+/*
+ * This routine is called whenever a serial port is opened.  It
+ * enables interrupts for a serial port, linking in its async structure into
+ * the IRQ chain.   It also performs the serial-specific
+ * initialization for the tty structure.
+ */
+static int mxser_open(struct tty_struct *tty, struct file *filp)
+{
+	struct tty_port *tport = tty->port;
+	struct mxser_port *port = container_of(tport, struct mxser_port, port);
+
+	tty->driver_data = port;
+
+	return tty_port_open(tport, tty, filp);
+}
+
+static void mxser_flush_buffer(struct tty_struct *tty)
+{
+	struct mxser_port *info = tty->driver_data;
+	unsigned long flags;
+
+	spin_lock_irqsave(&info->slock, flags);
+	kfifo_reset(&info->port.xmit_fifo);
+
+	outb(info->FCR | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
+		info->ioaddr + UART_FCR);
+
+	spin_unlock_irqrestore(&info->slock, flags);
+
+	tty_wakeup(tty);
+}
+
+static void mxser_close(struct tty_struct *tty, struct file *filp)
+{
+	tty_port_close(tty->port, tty, filp);
+}
+
+static int mxser_write(struct tty_struct *tty, const unsigned char *buf, int count)
+{
+	struct mxser_port *info = tty->driver_data;
+	unsigned long flags;
+	int written;
+	bool is_empty;
+
+	spin_lock_irqsave(&info->slock, flags);
+	written = kfifo_in(&info->port.xmit_fifo, buf, count);
+	is_empty = kfifo_is_empty(&info->port.xmit_fifo);
+	spin_unlock_irqrestore(&info->slock, flags);
+
+	if (!is_empty && !tty->flow.stopped)
+		if (!tty->hw_stopped || mxser_16550A_or_MUST(info))
+			mxser_start_tx(info);
+
+	return written;
+}
+
+static int mxser_put_char(struct tty_struct *tty, unsigned char ch)
+{
+	struct mxser_port *info = tty->driver_data;
+	unsigned long flags;
+	int ret;
+
+	spin_lock_irqsave(&info->slock, flags);
+	ret = kfifo_put(&info->port.xmit_fifo, ch);
+	spin_unlock_irqrestore(&info->slock, flags);
+
+	return ret;
+}
+
+
+static void mxser_flush_chars(struct tty_struct *tty)
+{
+	struct mxser_port *info = tty->driver_data;
+
+	if (kfifo_is_empty(&info->port.xmit_fifo) || tty->flow.stopped ||
+			(tty->hw_stopped && !mxser_16550A_or_MUST(info)))
+		return;
+
+	mxser_start_tx(info);
+}
+
+static unsigned int mxser_write_room(struct tty_struct *tty)
+{
+	struct mxser_port *info = tty->driver_data;
+
+	return kfifo_avail(&info->port.xmit_fifo);
+}
+
+static unsigned int mxser_chars_in_buffer(struct tty_struct *tty)
+{
+	struct mxser_port *info = tty->driver_data;
+
+	return kfifo_len(&info->port.xmit_fifo);
+}
+
+/*
+ * ------------------------------------------------------------
+ * friends of mxser_ioctl()
+ * ------------------------------------------------------------
+ */
+static int mxser_get_serial_info(struct tty_struct *tty,
+		struct serial_struct *ss)
+{
+	struct mxser_port *info = tty->driver_data;
+	struct tty_port *port = &info->port;
+	unsigned int closing_wait, close_delay;
+
+	mutex_lock(&port->mutex);
+
+	close_delay = jiffies_to_msecs(info->port.close_delay) / 10;
+	closing_wait = info->port.closing_wait;
+	if (closing_wait != ASYNC_CLOSING_WAIT_NONE)
+		closing_wait = jiffies_to_msecs(closing_wait) / 10;
+
+	ss->type = info->type;
+	ss->line = tty->index;
+	ss->port = info->ioaddr;
+	ss->irq = info->board->irq;
+	ss->flags = info->port.flags;
+	ss->baud_base = MXSER_BAUD_BASE;
+	ss->close_delay = close_delay;
+	ss->closing_wait = closing_wait;
+	ss->custom_divisor = MXSER_CUSTOM_DIVISOR,
+	mutex_unlock(&port->mutex);
+	return 0;
+}
+
+static int mxser_set_serial_info(struct tty_struct *tty,
+		struct serial_struct *ss)
+{
+	struct mxser_port *info = tty->driver_data;
+	struct tty_port *port = &info->port;
+	speed_t baud;
+	unsigned long sl_flags;
+	unsigned int old_speed, close_delay, closing_wait;
+	int retval = 0;
+
+	if (tty_io_error(tty))
+		return -EIO;
+
+	mutex_lock(&port->mutex);
+
+	if (ss->irq != info->board->irq ||
+			ss->port != info->ioaddr) {
+		mutex_unlock(&port->mutex);
+		return -EINVAL;
+	}
+
+	old_speed = port->flags & ASYNC_SPD_MASK;
+
+	close_delay = msecs_to_jiffies(ss->close_delay * 10);
+	closing_wait = ss->closing_wait;
+	if (closing_wait != ASYNC_CLOSING_WAIT_NONE)
+		closing_wait = msecs_to_jiffies(closing_wait * 10);
+
+	if (!capable(CAP_SYS_ADMIN)) {
+		if ((ss->baud_base != MXSER_BAUD_BASE) ||
+				(close_delay != port->close_delay) ||
+				(closing_wait != port->closing_wait) ||
+				((ss->flags & ~ASYNC_USR_MASK) != (port->flags & ~ASYNC_USR_MASK))) {
+			mutex_unlock(&port->mutex);
+			return -EPERM;
+		}
+		port->flags = (port->flags & ~ASYNC_USR_MASK) |
+				(ss->flags & ASYNC_USR_MASK);
+	} else {
+		/*
+		 * OK, past this point, all the error checking has been done.
+		 * At this point, we start making changes.....
+		 */
+		port->flags = ((port->flags & ~ASYNC_FLAGS) |
+				(ss->flags & ASYNC_FLAGS));
+		port->close_delay = close_delay;
+		port->closing_wait = closing_wait;
+		if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST &&
+				(ss->baud_base != MXSER_BAUD_BASE ||
+				ss->custom_divisor !=
+				MXSER_CUSTOM_DIVISOR)) {
+			if (ss->custom_divisor == 0) {
+				mutex_unlock(&port->mutex);
+				return -EINVAL;
+			}
+			baud = ss->baud_base / ss->custom_divisor;
+			tty_encode_baud_rate(tty, baud, baud);
+		}
+
+		info->type = ss->type;
+
+		mxser_process_txrx_fifo(info);
+	}
+
+	if (tty_port_initialized(port)) {
+		if (old_speed != (port->flags & ASYNC_SPD_MASK)) {
+			spin_lock_irqsave(&info->slock, sl_flags);
+			mxser_change_speed(tty, NULL);
+			spin_unlock_irqrestore(&info->slock, sl_flags);
+		}
+	} else {
+		retval = mxser_activate(port, tty);
+		if (retval == 0)
+			tty_port_set_initialized(port, 1);
+	}
+	mutex_unlock(&port->mutex);
+	return retval;
+}
+
+/*
+ * mxser_get_lsr_info - get line status register info
+ *
+ * Purpose: Let user call ioctl() to get info when the UART physically
+ *	    is emptied.  On bus types like RS485, the transmitter must
+ *	    release the bus after transmitting. This must be done when
+ *	    the transmit shift register is empty, not be done when the
+ *	    transmit holding register is empty.  This functionality
+ *	    allows an RS485 driver to be written in user space.
+ */
+static int mxser_get_lsr_info(struct mxser_port *info,
+		unsigned int __user *value)
+{
+	unsigned char status;
+	unsigned int result;
+	unsigned long flags;
+
+	spin_lock_irqsave(&info->slock, flags);
+	status = inb(info->ioaddr + UART_LSR);
+	spin_unlock_irqrestore(&info->slock, flags);
+	result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0);
+	return put_user(result, value);
+}
+
+static int mxser_tiocmget(struct tty_struct *tty)
+{
+	struct mxser_port *info = tty->driver_data;
+	unsigned char control;
+	unsigned long flags;
+	u8 msr;
+
+	if (tty_io_error(tty))
+		return -EIO;
+
+	spin_lock_irqsave(&info->slock, flags);
+	control = info->MCR;
+	msr = mxser_check_modem_status(tty, info);
+	spin_unlock_irqrestore(&info->slock, flags);
+
+	return ((control & UART_MCR_RTS) ? TIOCM_RTS : 0) |
+		    ((control & UART_MCR_DTR) ? TIOCM_DTR : 0) |
+		    ((msr & UART_MSR_DCD) ? TIOCM_CAR : 0) |
+		    ((msr & UART_MSR_RI) ? TIOCM_RNG : 0) |
+		    ((msr & UART_MSR_DSR) ? TIOCM_DSR : 0) |
+		    ((msr & UART_MSR_CTS) ? TIOCM_CTS : 0);
+}
+
+static int mxser_tiocmset(struct tty_struct *tty,
+		unsigned int set, unsigned int clear)
+{
+	struct mxser_port *info = tty->driver_data;
+	unsigned long flags;
+
+	if (tty_io_error(tty))
+		return -EIO;
+
+	spin_lock_irqsave(&info->slock, flags);
+
+	if (set & TIOCM_RTS)
+		info->MCR |= UART_MCR_RTS;
+	if (set & TIOCM_DTR)
+		info->MCR |= UART_MCR_DTR;
+
+	if (clear & TIOCM_RTS)
+		info->MCR &= ~UART_MCR_RTS;
+	if (clear & TIOCM_DTR)
+		info->MCR &= ~UART_MCR_DTR;
+
+	outb(info->MCR, info->ioaddr + UART_MCR);
+	spin_unlock_irqrestore(&info->slock, flags);
+	return 0;
+}
+
+static int mxser_cflags_changed(struct mxser_port *info, unsigned long arg,
+		struct async_icount *cprev)
+{
+	struct async_icount cnow;
+	unsigned long flags;
+	int ret;
+
+	spin_lock_irqsave(&info->slock, flags);
+	cnow = info->icount;	/* atomic copy */
+	spin_unlock_irqrestore(&info->slock, flags);
+
+	ret =	((arg & TIOCM_RNG) && (cnow.rng != cprev->rng)) ||
+		((arg & TIOCM_DSR) && (cnow.dsr != cprev->dsr)) ||
+		((arg & TIOCM_CD)  && (cnow.dcd != cprev->dcd)) ||
+		((arg & TIOCM_CTS) && (cnow.cts != cprev->cts));
+
+	*cprev = cnow;
+
+	return ret;
+}
+
+/* We should likely switch to TIOCGRS485/TIOCSRS485. */
+static int mxser_ioctl_op_mode(struct mxser_port *port, int index, bool set,
+		int __user *u_opmode)
+{
+	int opmode, p = index % 4;
+	int shiftbit = p * 2;
+	u8 val;
+
+	if (port->board->must_hwid != MOXA_MUST_MU860_HWID)
+		return -EFAULT;
+
+	if (set) {
+		if (get_user(opmode, u_opmode))
+			return -EFAULT;
+
+		if (opmode & ~OP_MODE_MASK)
+			return -EINVAL;
+
+		spin_lock_irq(&port->slock);
+		val = inb(port->opmode_ioaddr);
+		val &= ~(OP_MODE_MASK << shiftbit);
+		val |= (opmode << shiftbit);
+		outb(val, port->opmode_ioaddr);
+		spin_unlock_irq(&port->slock);
+
+		return 0;
+	}
+
+	spin_lock_irq(&port->slock);
+	opmode = inb(port->opmode_ioaddr) >> shiftbit;
+	spin_unlock_irq(&port->slock);
+
+	return put_user(opmode & OP_MODE_MASK, u_opmode);
+}
+
+static int mxser_ioctl(struct tty_struct *tty,
+		unsigned int cmd, unsigned long arg)
+{
+	struct mxser_port *info = tty->driver_data;
+	struct async_icount cnow;
+	unsigned long flags;
+	void __user *argp = (void __user *)arg;
+
+	if (cmd == MOXA_SET_OP_MODE || cmd == MOXA_GET_OP_MODE)
+		return mxser_ioctl_op_mode(info, tty->index,
+				cmd == MOXA_SET_OP_MODE, argp);
+
+	if (cmd != TIOCMIWAIT && tty_io_error(tty))
+		return -EIO;
+
+	switch (cmd) {
+	case TIOCSERGETLSR:	/* Get line status register */
+		return  mxser_get_lsr_info(info, argp);
+		/*
+		 * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change
+		 * - mask passed in arg for lines of interest
+		 *   (use |'ed TIOCM_RNG/DSR/CD/CTS for masking)
+		 * Caller should use TIOCGICOUNT to see which one it was
+		 */
+	case TIOCMIWAIT:
+		spin_lock_irqsave(&info->slock, flags);
+		cnow = info->icount;	/* note the counters on entry */
+		spin_unlock_irqrestore(&info->slock, flags);
+
+		return wait_event_interruptible(info->port.delta_msr_wait,
+				mxser_cflags_changed(info, arg, &cnow));
+	default:
+		return -ENOIOCTLCMD;
+	}
+	return 0;
+}
+
+	/*
+	 * Get counter of input serial line interrupts (DCD,RI,DSR,CTS)
+	 * Return: write counters to the user passed counter struct
+	 * NB: both 1->0 and 0->1 transitions are counted except for
+	 *     RI where only 0->1 is counted.
+	 */
+
+static int mxser_get_icount(struct tty_struct *tty,
+		struct serial_icounter_struct *icount)
+
+{
+	struct mxser_port *info = tty->driver_data;
+	struct async_icount cnow;
+	unsigned long flags;
+
+	spin_lock_irqsave(&info->slock, flags);
+	cnow = info->icount;
+	spin_unlock_irqrestore(&info->slock, flags);
+
+	icount->frame = cnow.frame;
+	icount->brk = cnow.brk;
+	icount->overrun = cnow.overrun;
+	icount->buf_overrun = cnow.buf_overrun;
+	icount->parity = cnow.parity;
+	icount->rx = cnow.rx;
+	icount->tx = cnow.tx;
+	icount->cts = cnow.cts;
+	icount->dsr = cnow.dsr;
+	icount->rng = cnow.rng;
+	icount->dcd = cnow.dcd;
+	return 0;
+}
+
+/*
+ * This routine is called by the upper-layer tty layer to signal that
+ * incoming characters should be throttled.
+ */
+static void mxser_throttle(struct tty_struct *tty)
+{
+	struct mxser_port *info = tty->driver_data;
+
+	if (I_IXOFF(tty)) {
+		if (info->board->must_hwid) {
+			info->IER &= ~MOXA_MUST_RECV_ISR;
+			outb(info->IER, info->ioaddr + UART_IER);
+		} else {
+			info->x_char = STOP_CHAR(tty);
+			outb(0, info->ioaddr + UART_IER);
+			info->IER |= UART_IER_THRI;
+			outb(info->IER, info->ioaddr + UART_IER);
+		}
+	}
+
+	if (C_CRTSCTS(tty)) {
+		info->MCR &= ~UART_MCR_RTS;
+		outb(info->MCR, info->ioaddr + UART_MCR);
+	}
+}
+
+static void mxser_unthrottle(struct tty_struct *tty)
+{
+	struct mxser_port *info = tty->driver_data;
+
+	/* startrx */
+	if (I_IXOFF(tty)) {
+		if (info->x_char)
+			info->x_char = 0;
+		else {
+			if (info->board->must_hwid) {
+				info->IER |= MOXA_MUST_RECV_ISR;
+				outb(info->IER, info->ioaddr + UART_IER);
+			} else {
+				info->x_char = START_CHAR(tty);
+				outb(0, info->ioaddr + UART_IER);
+				info->IER |= UART_IER_THRI;
+				outb(info->IER, info->ioaddr + UART_IER);
+			}
+		}
+	}
+
+	if (C_CRTSCTS(tty)) {
+		info->MCR |= UART_MCR_RTS;
+		outb(info->MCR, info->ioaddr + UART_MCR);
+	}
+}
+
+/*
+ * mxser_stop() and mxser_start()
+ *
+ * This routines are called before setting or resetting tty->flow.stopped.
+ * They enable or disable transmitter interrupts, as necessary.
+ */
+static void mxser_stop(struct tty_struct *tty)
+{
+	struct mxser_port *info = tty->driver_data;
+	unsigned long flags;
+
+	spin_lock_irqsave(&info->slock, flags);
+	if (info->IER & UART_IER_THRI)
+		__mxser_stop_tx(info);
+	spin_unlock_irqrestore(&info->slock, flags);
+}
+
+static void mxser_start(struct tty_struct *tty)
+{
+	struct mxser_port *info = tty->driver_data;
+	unsigned long flags;
+
+	spin_lock_irqsave(&info->slock, flags);
+	if (!kfifo_is_empty(&info->port.xmit_fifo))
+		__mxser_start_tx(info);
+	spin_unlock_irqrestore(&info->slock, flags);
+}
+
+static void mxser_set_termios(struct tty_struct *tty,
+			      const struct ktermios *old_termios)
+{
+	struct mxser_port *info = tty->driver_data;
+	unsigned long flags;
+
+	spin_lock_irqsave(&info->slock, flags);
+	mxser_change_speed(tty, old_termios);
+	spin_unlock_irqrestore(&info->slock, flags);
+
+	if ((old_termios->c_cflag & CRTSCTS) && !C_CRTSCTS(tty)) {
+		tty->hw_stopped = 0;
+		mxser_start(tty);
+	}
+
+	/* Handle sw stopped */
+	if ((old_termios->c_iflag & IXON) && !I_IXON(tty)) {
+		tty->flow.stopped = 0;
+
+		if (info->board->must_hwid) {
+			spin_lock_irqsave(&info->slock, flags);
+			mxser_must_set_rx_sw_flow_control(info->ioaddr, false);
+			spin_unlock_irqrestore(&info->slock, flags);
+		}
+
+		mxser_start(tty);
+	}
+}
+
+static bool mxser_tx_empty(struct mxser_port *info)
+{
+	unsigned long flags;
+	u8 lsr;
+
+	spin_lock_irqsave(&info->slock, flags);
+	lsr = inb(info->ioaddr + UART_LSR);
+	spin_unlock_irqrestore(&info->slock, flags);
+
+	return !(lsr & UART_LSR_TEMT);
+}
+
+/*
+ * mxser_wait_until_sent() --- wait until the transmitter is empty
+ */
+static void mxser_wait_until_sent(struct tty_struct *tty, int timeout)
+{
+	struct mxser_port *info = tty->driver_data;
+	unsigned long expire, char_time;
+
+	if (info->type == PORT_UNKNOWN)
+		return;
+
+	if (info->xmit_fifo_size == 0)
+		return;		/* Just in case.... */
+
+	/*
+	 * Set the check interval to be 1/5 of the estimated time to
+	 * send a single character, and make it at least 1.  The check
+	 * interval should also be less than the timeout.
+	 *
+	 * Note: we have to use pretty tight timings here to satisfy
+	 * the NIST-PCTS.
+	 */
+	char_time = (info->timeout - HZ / 50) / info->xmit_fifo_size;
+	char_time = char_time / 5;
+	if (char_time == 0)
+		char_time = 1;
+	if (timeout && timeout < char_time)
+		char_time = timeout;
+
+	char_time = jiffies_to_msecs(char_time);
+
+	/*
+	 * If the transmitter hasn't cleared in twice the approximate
+	 * amount of time to send the entire FIFO, it probably won't
+	 * ever clear.  This assumes the UART isn't doing flow
+	 * control, which is currently the case.  Hence, if it ever
+	 * takes longer than info->timeout, this is probably due to a
+	 * UART bug of some kind.  So, we clamp the timeout parameter at
+	 * 2*info->timeout.
+	 */
+	if (!timeout || timeout > 2 * info->timeout)
+		timeout = 2 * info->timeout;
+
+	expire = jiffies + timeout;
+
+	while (mxser_tx_empty(info)) {
+		msleep_interruptible(char_time);
+		if (signal_pending(current))
+			break;
+		if (time_after(jiffies, expire))
+			break;
+	}
+}
+
+/*
+ * This routine is called by tty_hangup() when a hangup is signaled.
+ */
+static void mxser_hangup(struct tty_struct *tty)
+{
+	struct mxser_port *info = tty->driver_data;
+
+	mxser_flush_buffer(tty);
+	tty_port_hangup(&info->port);
+}
+
+/*
+ * mxser_rs_break() --- routine which turns the break handling on or off
+ */
+static int mxser_rs_break(struct tty_struct *tty, int break_state)
+{
+	struct mxser_port *info = tty->driver_data;
+	unsigned long flags;
+	u8 lcr;
+
+	spin_lock_irqsave(&info->slock, flags);
+	lcr = inb(info->ioaddr + UART_LCR);
+	if (break_state == -1)
+		lcr |= UART_LCR_SBC;
+	else
+		lcr &= ~UART_LCR_SBC;
+	outb(lcr, info->ioaddr + UART_LCR);
+	spin_unlock_irqrestore(&info->slock, flags);
+
+	return 0;
+}
+
+static bool mxser_receive_chars_new(struct mxser_port *port, u8 status)
+{
+	enum mxser_must_hwid hwid = port->board->must_hwid;
+	u8 gdl;
+
+	if (hwid == MOXA_OTHER_UART)
+		return false;
+	if (status & (UART_LSR_BRK_ERROR_BITS | MOXA_MUST_LSR_RERR))
+		return false;
+
+	gdl = inb(port->ioaddr + MOXA_MUST_GDL_REGISTER);
+	if (hwid == MOXA_MUST_MU150_HWID)
+		gdl &= MOXA_MUST_GDL_MASK;
+
+	while (gdl--) {
+		u8 ch = inb(port->ioaddr + UART_RX);
+		if (!tty_insert_flip_char(&port->port, ch, 0))
+			port->icount.buf_overrun++;
+	}
+
+	return true;
+}
+
+static u8 mxser_receive_chars_old(struct tty_struct *tty,
+		                struct mxser_port *port, u8 status)
+{
+	enum mxser_must_hwid hwid = port->board->must_hwid;
+	int ignored = 0;
+	int max = 256;
+	u8 ch;
+
+	do {
+		if (max-- < 0)
+			break;
+
+		ch = inb(port->ioaddr + UART_RX);
+		if (hwid && (status & UART_LSR_OE))
+			outb(port->FCR | UART_FCR_CLEAR_RCVR,
+					port->ioaddr + UART_FCR);
+		status &= port->read_status_mask;
+		if (status & port->ignore_status_mask) {
+			if (++ignored > 100)
+				break;
+		} else {
+			char flag = 0;
+			if (status & UART_LSR_BRK_ERROR_BITS) {
+				if (status & UART_LSR_BI) {
+					flag = TTY_BREAK;
+					port->icount.brk++;
+
+					if (port->port.flags & ASYNC_SAK)
+						do_SAK(tty);
+				} else if (status & UART_LSR_PE) {
+					flag = TTY_PARITY;
+					port->icount.parity++;
+				} else if (status & UART_LSR_FE) {
+					flag = TTY_FRAME;
+					port->icount.frame++;
+				} else if (status & UART_LSR_OE) {
+					flag = TTY_OVERRUN;
+					port->icount.overrun++;
+				}
+			}
+			if (!tty_insert_flip_char(&port->port, ch, flag)) {
+				port->icount.buf_overrun++;
+				break;
+			}
+		}
+
+		if (hwid)
+			break;
+
+		status = inb(port->ioaddr + UART_LSR);
+	} while (status & UART_LSR_DR);
+
+	return status;
+}
+
+static u8 mxser_receive_chars(struct tty_struct *tty,
+		struct mxser_port *port, u8 status)
+{
+	if (!mxser_receive_chars_new(port, status))
+		status = mxser_receive_chars_old(tty, port, status);
+
+	tty_flip_buffer_push(&port->port);
+
+	return status;
+}
+
+static void mxser_transmit_chars(struct tty_struct *tty, struct mxser_port *port)
+{
+	int count;
+
+	if (port->x_char) {
+		outb(port->x_char, port->ioaddr + UART_TX);
+		port->x_char = 0;
+		port->icount.tx++;
+		return;
+	}
+
+	if (kfifo_is_empty(&port->port.xmit_fifo) || tty->flow.stopped ||
+			(tty->hw_stopped && !mxser_16550A_or_MUST(port))) {
+		__mxser_stop_tx(port);
+		return;
+	}
+
+	count = port->xmit_fifo_size;
+	do {
+		unsigned char c;
+
+		if (!kfifo_get(&port->port.xmit_fifo, &c))
+			break;
+
+		outb(c, port->ioaddr + UART_TX);
+		port->icount.tx++;
+	} while (--count > 0);
+
+	if (kfifo_len(&port->port.xmit_fifo) < WAKEUP_CHARS)
+		tty_wakeup(tty);
+
+	if (kfifo_is_empty(&port->port.xmit_fifo))
+		__mxser_stop_tx(port);
+}
+
+static bool mxser_port_isr(struct mxser_port *port)
+{
+	struct tty_struct *tty;
+	u8 iir, status;
+	bool error = false;
+
+	iir = inb(port->ioaddr + UART_IIR);
+	if (iir & UART_IIR_NO_INT)
+		return true;
+
+	iir &= MOXA_MUST_IIR_MASK;
+	tty = tty_port_tty_get(&port->port);
+	if (!tty) {
+		status = inb(port->ioaddr + UART_LSR);
+		outb(port->FCR | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
+				port->ioaddr + UART_FCR);
+		inb(port->ioaddr + UART_MSR);
+
+		error = true;
+		goto put_tty;
+	}
+
+	status = inb(port->ioaddr + UART_LSR);
+
+	if (port->board->must_hwid) {
+		if (iir == MOXA_MUST_IIR_GDA ||
+		    iir == MOXA_MUST_IIR_RDA ||
+		    iir == MOXA_MUST_IIR_RTO ||
+		    iir == MOXA_MUST_IIR_LSR)
+			status = mxser_receive_chars(tty, port, status);
+	} else {
+		status &= port->read_status_mask;
+		if (status & UART_LSR_DR)
+			status = mxser_receive_chars(tty, port, status);
+	}
+
+	mxser_check_modem_status(tty, port);
+
+	if (port->board->must_hwid) {
+		if (iir == 0x02 && (status & UART_LSR_THRE))
+			mxser_transmit_chars(tty, port);
+	} else {
+		if (status & UART_LSR_THRE)
+			mxser_transmit_chars(tty, port);
+	}
+
+put_tty:
+	tty_kref_put(tty);
+
+	return error;
+}
+
+/*
+ * This is the serial driver's generic interrupt routine
+ */
+static irqreturn_t mxser_interrupt(int irq, void *dev_id)
+{
+	struct mxser_board *brd = dev_id;
+	struct mxser_port *port;
+	unsigned int int_cnt, pass_counter = 0;
+	unsigned int i, max = brd->nports;
+	int handled = IRQ_NONE;
+	u8 irqbits, bits, mask = BIT(max) - 1;
+
+	while (pass_counter++ < MXSER_ISR_PASS_LIMIT) {
+		irqbits = inb(brd->vector) & mask;
+		if (irqbits == mask)
+			break;
+
+		handled = IRQ_HANDLED;
+		for (i = 0, bits = 1; i < max; i++, irqbits |= bits, bits <<= 1) {
+			if (irqbits == mask)
+				break;
+			if (bits & irqbits)
+				continue;
+			port = &brd->ports[i];
+
+			int_cnt = 0;
+			spin_lock(&port->slock);
+			do {
+				if (mxser_port_isr(port))
+					break;
+			} while (int_cnt++ < MXSER_ISR_PASS_LIMIT);
+			spin_unlock(&port->slock);
+		}
+	}
+
+	return handled;
+}
+
+static const struct tty_operations mxser_ops = {
+	.open = mxser_open,
+	.close = mxser_close,
+	.write = mxser_write,
+	.put_char = mxser_put_char,
+	.flush_chars = mxser_flush_chars,
+	.write_room = mxser_write_room,
+	.chars_in_buffer = mxser_chars_in_buffer,
+	.flush_buffer = mxser_flush_buffer,
+	.ioctl = mxser_ioctl,
+	.throttle = mxser_throttle,
+	.unthrottle = mxser_unthrottle,
+	.set_termios = mxser_set_termios,
+	.stop = mxser_stop,
+	.start = mxser_start,
+	.hangup = mxser_hangup,
+	.break_ctl = mxser_rs_break,
+	.wait_until_sent = mxser_wait_until_sent,
+	.tiocmget = mxser_tiocmget,
+	.tiocmset = mxser_tiocmset,
+	.set_serial = mxser_set_serial_info,
+	.get_serial = mxser_get_serial_info,
+	.get_icount = mxser_get_icount,
+};
+
+static const struct tty_port_operations mxser_port_ops = {
+	.carrier_raised = mxser_carrier_raised,
+	.dtr_rts = mxser_dtr_rts,
+	.activate = mxser_activate,
+	.shutdown = mxser_shutdown_port,
+};
+
+/*
+ * The MOXA Smartio/Industio serial driver boot-time initialization code!
+ */
+
+static void mxser_initbrd(struct mxser_board *brd, bool high_baud)
+{
+	struct mxser_port *info;
+	unsigned int i;
+	bool is_mu860;
+
+	brd->must_hwid = mxser_must_get_hwid(brd->ports[0].ioaddr);
+	is_mu860 = brd->must_hwid == MOXA_MUST_MU860_HWID;
+
+	for (i = 0; i < UART_INFO_NUM; i++) {
+		if (Gpci_uart_info[i].type == brd->must_hwid) {
+			brd->max_baud = Gpci_uart_info[i].max_baud;
+
+			/* exception....CP-102 */
+			if (high_baud)
+				brd->max_baud = 921600;
+			break;
+		}
+	}
+
+	if (is_mu860) {
+		/* set to RS232 mode by default */
+		outb(0, brd->vector + 4);
+		outb(0, brd->vector + 0x0c);
+	}
+
+	for (i = 0; i < brd->nports; i++) {
+		info = &brd->ports[i];
+		if (is_mu860) {
+			if (i < 4)
+				info->opmode_ioaddr = brd->vector + 4;
+			else
+				info->opmode_ioaddr = brd->vector + 0x0c;
+		}
+		tty_port_init(&info->port);
+		info->port.ops = &mxser_port_ops;
+		info->board = brd;
+
+		/* Enhance mode enabled here */
+		if (brd->must_hwid != MOXA_OTHER_UART)
+			mxser_must_set_enhance_mode(info->ioaddr, true);
+
+		info->type = PORT_16550A;
+
+		mxser_process_txrx_fifo(info);
+
+		info->port.close_delay = 5 * HZ / 10;
+		info->port.closing_wait = 30 * HZ;
+		spin_lock_init(&info->slock);
+
+		/* before set INT ISR, disable all int */
+		outb(inb(info->ioaddr + UART_IER) & 0xf0,
+			info->ioaddr + UART_IER);
+	}
+}
+
+static int mxser_probe(struct pci_dev *pdev,
+		const struct pci_device_id *ent)
+{
+	struct mxser_board *brd;
+	unsigned int i, base;
+	unsigned long ioaddress;
+	unsigned short nports = MXSER_NPORTS(ent->driver_data);
+	struct device *tty_dev;
+	int retval = -EINVAL;
+
+	i = find_first_zero_bit(mxser_boards, MXSER_BOARDS);
+	if (i >= MXSER_BOARDS) {
+		dev_err(&pdev->dev, "too many boards found (maximum %d), board "
+				"not configured\n", MXSER_BOARDS);
+		goto err;
+	}
+
+	brd = devm_kzalloc(&pdev->dev, struct_size(brd, ports, nports),
+			GFP_KERNEL);
+	if (!brd)
+		goto err;
+
+	brd->idx = i;
+	__set_bit(brd->idx, mxser_boards);
+	base = i * MXSER_PORTS_PER_BOARD;
+
+	retval = pcim_enable_device(pdev);
+	if (retval) {
+		dev_err(&pdev->dev, "PCI enable failed\n");
+		goto err_zero;
+	}
+
+	/* io address */
+	ioaddress = pci_resource_start(pdev, 2);
+	retval = pci_request_region(pdev, 2, "mxser(IO)");
+	if (retval)
+		goto err_zero;
+
+	brd->nports = nports;
+	for (i = 0; i < nports; i++)
+		brd->ports[i].ioaddr = ioaddress + 8 * i;
+
+	/* vector */
+	ioaddress = pci_resource_start(pdev, 3);
+	retval = pci_request_region(pdev, 3, "mxser(vector)");
+	if (retval)
+		goto err_zero;
+	brd->vector = ioaddress;
+
+	/* irq */
+	brd->irq = pdev->irq;
+
+	mxser_initbrd(brd, ent->driver_data & MXSER_HIGHBAUD);
+
+	retval = devm_request_irq(&pdev->dev, brd->irq, mxser_interrupt,
+			IRQF_SHARED, "mxser", brd);
+	if (retval) {
+		dev_err(&pdev->dev, "request irq failed");
+		goto err_relbrd;
+	}
+
+	for (i = 0; i < nports; i++) {
+		tty_dev = tty_port_register_device(&brd->ports[i].port,
+				mxvar_sdriver, base + i, &pdev->dev);
+		if (IS_ERR(tty_dev)) {
+			retval = PTR_ERR(tty_dev);
+			for (; i > 0; i--)
+				tty_unregister_device(mxvar_sdriver,
+					base + i - 1);
+			goto err_relbrd;
+		}
+	}
+
+	pci_set_drvdata(pdev, brd);
+
+	return 0;
+err_relbrd:
+	for (i = 0; i < nports; i++)
+		tty_port_destroy(&brd->ports[i].port);
+err_zero:
+	__clear_bit(brd->idx, mxser_boards);
+err:
+	return retval;
+}
+
+static void mxser_remove(struct pci_dev *pdev)
+{
+	struct mxser_board *brd = pci_get_drvdata(pdev);
+	unsigned int i, base = brd->idx * MXSER_PORTS_PER_BOARD;
+
+	for (i = 0; i < brd->nports; i++) {
+		tty_unregister_device(mxvar_sdriver, base + i);
+		tty_port_destroy(&brd->ports[i].port);
+	}
+
+	__clear_bit(brd->idx, mxser_boards);
+}
+
+static struct pci_driver mxser_driver = {
+	.name = "mxser",
+	.id_table = mxser_pcibrds,
+	.probe = mxser_probe,
+	.remove = mxser_remove
+};
+
+static int __init mxser_module_init(void)
+{
+	int retval;
+
+	mxvar_sdriver = tty_alloc_driver(MXSER_PORTS, TTY_DRIVER_REAL_RAW |
+			TTY_DRIVER_DYNAMIC_DEV);
+	if (IS_ERR(mxvar_sdriver))
+		return PTR_ERR(mxvar_sdriver);
+
+	/* Initialize the tty_driver structure */
+	mxvar_sdriver->name = "ttyMI";
+	mxvar_sdriver->major = ttymajor;
+	mxvar_sdriver->minor_start = 0;
+	mxvar_sdriver->type = TTY_DRIVER_TYPE_SERIAL;
+	mxvar_sdriver->subtype = SERIAL_TYPE_NORMAL;
+	mxvar_sdriver->init_termios = tty_std_termios;
+	mxvar_sdriver->init_termios.c_cflag = B9600|CS8|CREAD|HUPCL|CLOCAL;
+	tty_set_operations(mxvar_sdriver, &mxser_ops);
+
+	retval = tty_register_driver(mxvar_sdriver);
+	if (retval) {
+		printk(KERN_ERR "Couldn't install MOXA Smartio/Industio family "
+				"tty driver !\n");
+		goto err_put;
+	}
+
+	retval = pci_register_driver(&mxser_driver);
+	if (retval) {
+		printk(KERN_ERR "mxser: can't register pci driver\n");
+		goto err_unr;
+	}
+
+	return 0;
+err_unr:
+	tty_unregister_driver(mxvar_sdriver);
+err_put:
+	tty_driver_kref_put(mxvar_sdriver);
+	return retval;
+}
+
+static void __exit mxser_module_exit(void)
+{
+	pci_unregister_driver(&mxser_driver);
+	tty_unregister_driver(mxvar_sdriver);
+	tty_driver_kref_put(mxvar_sdriver);
+}
+
+module_init(mxser_module_init);
+module_exit(mxser_module_exit);