Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 729 insertions, 0 deletions

diff --git a/sound/soc/ux500/ux500_msp_i2s.c b/sound/soc/ux500/ux500_msp_i2s.c
new file mode 100644
index 000000000..d113411a1
--- /dev/null
+++ b/sound/soc/ux500/ux500_msp_i2s.c
@@ -0,0 +1,729 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) ST-Ericsson SA 2012
+ *
+ * Author: Ola Lilja <ola.o.lilja@stericsson.com>,
+ *         Roger Nilsson <roger.xr.nilsson@stericsson.com>,
+ *         Sandeep Kaushik <sandeep.kaushik@st.com>
+ *         for ST-Ericsson.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/platform_data/asoc-ux500-msp.h>
+
+#include <sound/soc.h>
+
+#include "ux500_msp_i2s.h"
+
+ /* Protocol desciptors */
+static const struct msp_protdesc prot_descs[] = {
+	{ /* I2S */
+		MSP_SINGLE_PHASE,
+		MSP_SINGLE_PHASE,
+		MSP_PHASE2_START_MODE_IMEDIATE,
+		MSP_PHASE2_START_MODE_IMEDIATE,
+		MSP_BTF_MS_BIT_FIRST,
+		MSP_BTF_MS_BIT_FIRST,
+		MSP_FRAME_LEN_1,
+		MSP_FRAME_LEN_1,
+		MSP_FRAME_LEN_1,
+		MSP_FRAME_LEN_1,
+		MSP_ELEM_LEN_32,
+		MSP_ELEM_LEN_32,
+		MSP_ELEM_LEN_32,
+		MSP_ELEM_LEN_32,
+		MSP_DELAY_1,
+		MSP_DELAY_1,
+		MSP_RISING_EDGE,
+		MSP_FALLING_EDGE,
+		MSP_FSYNC_POL_ACT_LO,
+		MSP_FSYNC_POL_ACT_LO,
+		MSP_SWAP_NONE,
+		MSP_SWAP_NONE,
+		MSP_COMPRESS_MODE_LINEAR,
+		MSP_EXPAND_MODE_LINEAR,
+		MSP_FSYNC_IGNORE,
+		31,
+		15,
+		32,
+	}, { /* PCM */
+		MSP_DUAL_PHASE,
+		MSP_DUAL_PHASE,
+		MSP_PHASE2_START_MODE_FSYNC,
+		MSP_PHASE2_START_MODE_FSYNC,
+		MSP_BTF_MS_BIT_FIRST,
+		MSP_BTF_MS_BIT_FIRST,
+		MSP_FRAME_LEN_1,
+		MSP_FRAME_LEN_1,
+		MSP_FRAME_LEN_1,
+		MSP_FRAME_LEN_1,
+		MSP_ELEM_LEN_16,
+		MSP_ELEM_LEN_16,
+		MSP_ELEM_LEN_16,
+		MSP_ELEM_LEN_16,
+		MSP_DELAY_0,
+		MSP_DELAY_0,
+		MSP_RISING_EDGE,
+		MSP_FALLING_EDGE,
+		MSP_FSYNC_POL_ACT_HI,
+		MSP_FSYNC_POL_ACT_HI,
+		MSP_SWAP_NONE,
+		MSP_SWAP_NONE,
+		MSP_COMPRESS_MODE_LINEAR,
+		MSP_EXPAND_MODE_LINEAR,
+		MSP_FSYNC_IGNORE,
+		255,
+		0,
+		256,
+	}, { /* Companded PCM */
+		MSP_SINGLE_PHASE,
+		MSP_SINGLE_PHASE,
+		MSP_PHASE2_START_MODE_FSYNC,
+		MSP_PHASE2_START_MODE_FSYNC,
+		MSP_BTF_MS_BIT_FIRST,
+		MSP_BTF_MS_BIT_FIRST,
+		MSP_FRAME_LEN_1,
+		MSP_FRAME_LEN_1,
+		MSP_FRAME_LEN_1,
+		MSP_FRAME_LEN_1,
+		MSP_ELEM_LEN_8,
+		MSP_ELEM_LEN_8,
+		MSP_ELEM_LEN_8,
+		MSP_ELEM_LEN_8,
+		MSP_DELAY_0,
+		MSP_DELAY_0,
+		MSP_RISING_EDGE,
+		MSP_RISING_EDGE,
+		MSP_FSYNC_POL_ACT_HI,
+		MSP_FSYNC_POL_ACT_HI,
+		MSP_SWAP_NONE,
+		MSP_SWAP_NONE,
+		MSP_COMPRESS_MODE_LINEAR,
+		MSP_EXPAND_MODE_LINEAR,
+		MSP_FSYNC_IGNORE,
+		255,
+		0,
+		256,
+	},
+};
+
+static void set_prot_desc_tx(struct ux500_msp *msp,
+			struct msp_protdesc *protdesc,
+			enum msp_data_size data_size)
+{
+	u32 temp_reg = 0;
+
+	temp_reg |= MSP_P2_ENABLE_BIT(protdesc->tx_phase_mode);
+	temp_reg |= MSP_P2_START_MODE_BIT(protdesc->tx_phase2_start_mode);
+	temp_reg |= MSP_P1_FRAME_LEN_BITS(protdesc->tx_frame_len_1);
+	temp_reg |= MSP_P2_FRAME_LEN_BITS(protdesc->tx_frame_len_2);
+	if (msp->def_elem_len) {
+		temp_reg |= MSP_P1_ELEM_LEN_BITS(protdesc->tx_elem_len_1);
+		temp_reg |= MSP_P2_ELEM_LEN_BITS(protdesc->tx_elem_len_2);
+	} else {
+		temp_reg |= MSP_P1_ELEM_LEN_BITS(data_size);
+		temp_reg |= MSP_P2_ELEM_LEN_BITS(data_size);
+	}
+	temp_reg |= MSP_DATA_DELAY_BITS(protdesc->tx_data_delay);
+	temp_reg |= MSP_SET_ENDIANNES_BIT(protdesc->tx_byte_order);
+	temp_reg |= MSP_FSYNC_POL(protdesc->tx_fsync_pol);
+	temp_reg |= MSP_DATA_WORD_SWAP(protdesc->tx_half_word_swap);
+	temp_reg |= MSP_SET_COMPANDING_MODE(protdesc->compression_mode);
+	temp_reg |= MSP_SET_FSYNC_IGNORE(protdesc->frame_sync_ignore);
+
+	writel(temp_reg, msp->registers + MSP_TCF);
+}
+
+static void set_prot_desc_rx(struct ux500_msp *msp,
+			struct msp_protdesc *protdesc,
+			enum msp_data_size data_size)
+{
+	u32 temp_reg = 0;
+
+	temp_reg |= MSP_P2_ENABLE_BIT(protdesc->rx_phase_mode);
+	temp_reg |= MSP_P2_START_MODE_BIT(protdesc->rx_phase2_start_mode);
+	temp_reg |= MSP_P1_FRAME_LEN_BITS(protdesc->rx_frame_len_1);
+	temp_reg |= MSP_P2_FRAME_LEN_BITS(protdesc->rx_frame_len_2);
+	if (msp->def_elem_len) {
+		temp_reg |= MSP_P1_ELEM_LEN_BITS(protdesc->rx_elem_len_1);
+		temp_reg |= MSP_P2_ELEM_LEN_BITS(protdesc->rx_elem_len_2);
+	} else {
+		temp_reg |= MSP_P1_ELEM_LEN_BITS(data_size);
+		temp_reg |= MSP_P2_ELEM_LEN_BITS(data_size);
+	}
+
+	temp_reg |= MSP_DATA_DELAY_BITS(protdesc->rx_data_delay);
+	temp_reg |= MSP_SET_ENDIANNES_BIT(protdesc->rx_byte_order);
+	temp_reg |= MSP_FSYNC_POL(protdesc->rx_fsync_pol);
+	temp_reg |= MSP_DATA_WORD_SWAP(protdesc->rx_half_word_swap);
+	temp_reg |= MSP_SET_COMPANDING_MODE(protdesc->expansion_mode);
+	temp_reg |= MSP_SET_FSYNC_IGNORE(protdesc->frame_sync_ignore);
+
+	writel(temp_reg, msp->registers + MSP_RCF);
+}
+
+static int configure_protocol(struct ux500_msp *msp,
+			struct ux500_msp_config *config)
+{
+	struct msp_protdesc *protdesc;
+	enum msp_data_size data_size;
+	u32 temp_reg = 0;
+
+	data_size = config->data_size;
+	msp->def_elem_len = config->def_elem_len;
+	if (config->default_protdesc == 1) {
+		if (config->protocol >= MSP_INVALID_PROTOCOL) {
+			dev_err(msp->dev, "%s: ERROR: Invalid protocol!\n",
+				__func__);
+			return -EINVAL;
+		}
+		protdesc =
+		    (struct msp_protdesc *)&prot_descs[config->protocol];
+	} else {
+		protdesc = (struct msp_protdesc *)&config->protdesc;
+	}
+
+	if (data_size < MSP_DATA_BITS_DEFAULT || data_size > MSP_DATA_BITS_32) {
+		dev_err(msp->dev,
+			"%s: ERROR: Invalid data-size requested (data_size = %d)!\n",
+			__func__, data_size);
+		return -EINVAL;
+	}
+
+	if (config->direction & MSP_DIR_TX)
+		set_prot_desc_tx(msp, protdesc, data_size);
+	if (config->direction & MSP_DIR_RX)
+		set_prot_desc_rx(msp, protdesc, data_size);
+
+	/* The code below should not be separated. */
+	temp_reg = readl(msp->registers + MSP_GCR) & ~TX_CLK_POL_RISING;
+	temp_reg |= MSP_TX_CLKPOL_BIT(~protdesc->tx_clk_pol);
+	writel(temp_reg, msp->registers + MSP_GCR);
+	temp_reg = readl(msp->registers + MSP_GCR) & ~RX_CLK_POL_RISING;
+	temp_reg |= MSP_RX_CLKPOL_BIT(protdesc->rx_clk_pol);
+	writel(temp_reg, msp->registers + MSP_GCR);
+
+	return 0;
+}
+
+static int setup_bitclk(struct ux500_msp *msp, struct ux500_msp_config *config)
+{
+	u32 reg_val_GCR;
+	u32 frame_per = 0;
+	u32 sck_div = 0;
+	u32 frame_width = 0;
+	u32 temp_reg = 0;
+	struct msp_protdesc *protdesc = NULL;
+
+	reg_val_GCR = readl(msp->registers + MSP_GCR);
+	writel(reg_val_GCR & ~SRG_ENABLE, msp->registers + MSP_GCR);
+
+	if (config->default_protdesc)
+		protdesc =
+			(struct msp_protdesc *)&prot_descs[config->protocol];
+	else
+		protdesc = (struct msp_protdesc *)&config->protdesc;
+
+	switch (config->protocol) {
+	case MSP_PCM_PROTOCOL:
+	case MSP_PCM_COMPAND_PROTOCOL:
+		frame_width = protdesc->frame_width;
+		sck_div = config->f_inputclk / (config->frame_freq *
+			(protdesc->clocks_per_frame));
+		frame_per = protdesc->frame_period;
+		break;
+	case MSP_I2S_PROTOCOL:
+		frame_width = protdesc->frame_width;
+		sck_div = config->f_inputclk / (config->frame_freq *
+			(protdesc->clocks_per_frame));
+		frame_per = protdesc->frame_period;
+		break;
+	default:
+		dev_err(msp->dev, "%s: ERROR: Unknown protocol (%d)!\n",
+			__func__,
+			config->protocol);
+		return -EINVAL;
+	}
+
+	temp_reg = (sck_div - 1) & SCK_DIV_MASK;
+	temp_reg |= FRAME_WIDTH_BITS(frame_width);
+	temp_reg |= FRAME_PERIOD_BITS(frame_per);
+	writel(temp_reg, msp->registers + MSP_SRG);
+
+	msp->f_bitclk = (config->f_inputclk)/(sck_div + 1);
+
+	/* Enable bit-clock */
+	udelay(100);
+	reg_val_GCR = readl(msp->registers + MSP_GCR);
+	writel(reg_val_GCR | SRG_ENABLE, msp->registers + MSP_GCR);
+	udelay(100);
+
+	return 0;
+}
+
+static int configure_multichannel(struct ux500_msp *msp,
+				struct ux500_msp_config *config)
+{
+	struct msp_protdesc *protdesc;
+	struct msp_multichannel_config *mcfg;
+	u32 reg_val_MCR;
+
+	if (config->default_protdesc == 1) {
+		if (config->protocol >= MSP_INVALID_PROTOCOL) {
+			dev_err(msp->dev,
+				"%s: ERROR: Invalid protocol (%d)!\n",
+				__func__, config->protocol);
+			return -EINVAL;
+		}
+		protdesc = (struct msp_protdesc *)
+				&prot_descs[config->protocol];
+	} else {
+		protdesc = (struct msp_protdesc *)&config->protdesc;
+	}
+
+	mcfg = &config->multichannel_config;
+	if (mcfg->tx_multichannel_enable) {
+		if (protdesc->tx_phase_mode == MSP_SINGLE_PHASE) {
+			reg_val_MCR = readl(msp->registers + MSP_MCR);
+			writel(reg_val_MCR | (mcfg->tx_multichannel_enable ?
+						1 << TMCEN_BIT : 0),
+				msp->registers + MSP_MCR);
+			writel(mcfg->tx_channel_0_enable,
+				msp->registers + MSP_TCE0);
+			writel(mcfg->tx_channel_1_enable,
+				msp->registers + MSP_TCE1);
+			writel(mcfg->tx_channel_2_enable,
+				msp->registers + MSP_TCE2);
+			writel(mcfg->tx_channel_3_enable,
+				msp->registers + MSP_TCE3);
+		} else {
+			dev_err(msp->dev,
+				"%s: ERROR: Only single-phase supported (TX-mode: %d)!\n",
+				__func__, protdesc->tx_phase_mode);
+			return -EINVAL;
+		}
+	}
+	if (mcfg->rx_multichannel_enable) {
+		if (protdesc->rx_phase_mode == MSP_SINGLE_PHASE) {
+			reg_val_MCR = readl(msp->registers + MSP_MCR);
+			writel(reg_val_MCR | (mcfg->rx_multichannel_enable ?
+						1 << RMCEN_BIT : 0),
+				msp->registers + MSP_MCR);
+			writel(mcfg->rx_channel_0_enable,
+					msp->registers + MSP_RCE0);
+			writel(mcfg->rx_channel_1_enable,
+					msp->registers + MSP_RCE1);
+			writel(mcfg->rx_channel_2_enable,
+					msp->registers + MSP_RCE2);
+			writel(mcfg->rx_channel_3_enable,
+					msp->registers + MSP_RCE3);
+		} else {
+			dev_err(msp->dev,
+				"%s: ERROR: Only single-phase supported (RX-mode: %d)!\n",
+				__func__, protdesc->rx_phase_mode);
+			return -EINVAL;
+		}
+		if (mcfg->rx_comparison_enable_mode) {
+			reg_val_MCR = readl(msp->registers + MSP_MCR);
+			writel(reg_val_MCR |
+				(mcfg->rx_comparison_enable_mode << RCMPM_BIT),
+				msp->registers + MSP_MCR);
+
+			writel(mcfg->comparison_mask,
+					msp->registers + MSP_RCM);
+			writel(mcfg->comparison_value,
+					msp->registers + MSP_RCV);
+
+		}
+	}
+
+	return 0;
+}
+
+static int enable_msp(struct ux500_msp *msp, struct ux500_msp_config *config)
+{
+	int status = 0;
+	u32 reg_val_DMACR, reg_val_GCR;
+
+	/* Configure msp with protocol dependent settings */
+	configure_protocol(msp, config);
+	setup_bitclk(msp, config);
+	if (config->multichannel_configured == 1) {
+		status = configure_multichannel(msp, config);
+		if (status)
+			dev_warn(msp->dev,
+				"%s: WARN: configure_multichannel failed (%d)!\n",
+				__func__, status);
+	}
+
+	/* Make sure the correct DMA-directions are configured */
+	if ((config->direction & MSP_DIR_RX) &&
+			!msp->capture_dma_data.dma_cfg) {
+		dev_err(msp->dev, "%s: ERROR: MSP RX-mode is not configured!",
+			__func__);
+		return -EINVAL;
+	}
+	if ((config->direction == MSP_DIR_TX) &&
+			!msp->playback_dma_data.dma_cfg) {
+		dev_err(msp->dev, "%s: ERROR: MSP TX-mode is not configured!",
+			__func__);
+		return -EINVAL;
+	}
+
+	reg_val_DMACR = readl(msp->registers + MSP_DMACR);
+	if (config->direction & MSP_DIR_RX)
+		reg_val_DMACR |= RX_DMA_ENABLE;
+	if (config->direction & MSP_DIR_TX)
+		reg_val_DMACR |= TX_DMA_ENABLE;
+	writel(reg_val_DMACR, msp->registers + MSP_DMACR);
+
+	writel(config->iodelay, msp->registers + MSP_IODLY);
+
+	/* Enable frame generation logic */
+	reg_val_GCR = readl(msp->registers + MSP_GCR);
+	writel(reg_val_GCR | FRAME_GEN_ENABLE, msp->registers + MSP_GCR);
+
+	return status;
+}
+
+static void flush_fifo_rx(struct ux500_msp *msp)
+{
+	u32 reg_val_GCR, reg_val_FLR;
+	u32 limit = 32;
+
+	reg_val_GCR = readl(msp->registers + MSP_GCR);
+	writel(reg_val_GCR | RX_ENABLE, msp->registers + MSP_GCR);
+
+	reg_val_FLR = readl(msp->registers + MSP_FLR);
+	while (!(reg_val_FLR & RX_FIFO_EMPTY) && limit--) {
+		readl(msp->registers + MSP_DR);
+		reg_val_FLR = readl(msp->registers + MSP_FLR);
+	}
+
+	writel(reg_val_GCR, msp->registers + MSP_GCR);
+}
+
+static void flush_fifo_tx(struct ux500_msp *msp)
+{
+	u32 reg_val_GCR, reg_val_FLR;
+	u32 limit = 32;
+
+	reg_val_GCR = readl(msp->registers + MSP_GCR);
+	writel(reg_val_GCR | TX_ENABLE, msp->registers + MSP_GCR);
+	writel(MSP_ITCR_ITEN | MSP_ITCR_TESTFIFO, msp->registers + MSP_ITCR);
+
+	reg_val_FLR = readl(msp->registers + MSP_FLR);
+	while (!(reg_val_FLR & TX_FIFO_EMPTY) && limit--) {
+		readl(msp->registers + MSP_TSTDR);
+		reg_val_FLR = readl(msp->registers + MSP_FLR);
+	}
+	writel(0x0, msp->registers + MSP_ITCR);
+	writel(reg_val_GCR, msp->registers + MSP_GCR);
+}
+
+int ux500_msp_i2s_open(struct ux500_msp *msp,
+		struct ux500_msp_config *config)
+{
+	u32 old_reg, new_reg, mask;
+	int res;
+	unsigned int tx_sel, rx_sel, tx_busy, rx_busy;
+
+	if (in_interrupt()) {
+		dev_err(msp->dev,
+			"%s: ERROR: Open called in interrupt context!\n",
+			__func__);
+		return -1;
+	}
+
+	tx_sel = (config->direction & MSP_DIR_TX) > 0;
+	rx_sel = (config->direction & MSP_DIR_RX) > 0;
+	if (!tx_sel && !rx_sel) {
+		dev_err(msp->dev, "%s: Error: No direction selected!\n",
+			__func__);
+		return -EINVAL;
+	}
+
+	tx_busy = (msp->dir_busy & MSP_DIR_TX) > 0;
+	rx_busy = (msp->dir_busy & MSP_DIR_RX) > 0;
+	if (tx_busy && tx_sel) {
+		dev_err(msp->dev, "%s: Error: TX is in use!\n", __func__);
+		return -EBUSY;
+	}
+	if (rx_busy && rx_sel) {
+		dev_err(msp->dev, "%s: Error: RX is in use!\n", __func__);
+		return -EBUSY;
+	}
+
+	msp->dir_busy |= (tx_sel ? MSP_DIR_TX : 0) | (rx_sel ? MSP_DIR_RX : 0);
+
+	/* First do the global config register */
+	mask = RX_CLK_SEL_MASK | TX_CLK_SEL_MASK | RX_FSYNC_MASK |
+	    TX_FSYNC_MASK | RX_SYNC_SEL_MASK | TX_SYNC_SEL_MASK |
+	    RX_FIFO_ENABLE_MASK | TX_FIFO_ENABLE_MASK | SRG_CLK_SEL_MASK |
+	    LOOPBACK_MASK | TX_EXTRA_DELAY_MASK;
+
+	new_reg = (config->tx_clk_sel | config->rx_clk_sel |
+		config->rx_fsync_pol | config->tx_fsync_pol |
+		config->rx_fsync_sel | config->tx_fsync_sel |
+		config->rx_fifo_config | config->tx_fifo_config |
+		config->srg_clk_sel | config->loopback_enable |
+		config->tx_data_enable);
+
+	old_reg = readl(msp->registers + MSP_GCR);
+	old_reg &= ~mask;
+	new_reg |= old_reg;
+	writel(new_reg, msp->registers + MSP_GCR);
+
+	res = enable_msp(msp, config);
+	if (res < 0) {
+		dev_err(msp->dev, "%s: ERROR: enable_msp failed (%d)!\n",
+			__func__, res);
+		return -EBUSY;
+	}
+	if (config->loopback_enable & 0x80)
+		msp->loopback_enable = 1;
+
+	/* Flush FIFOs */
+	flush_fifo_tx(msp);
+	flush_fifo_rx(msp);
+
+	msp->msp_state = MSP_STATE_CONFIGURED;
+	return 0;
+}
+
+static void disable_msp_rx(struct ux500_msp *msp)
+{
+	u32 reg_val_GCR, reg_val_DMACR, reg_val_IMSC;
+
+	reg_val_GCR = readl(msp->registers + MSP_GCR);
+	writel(reg_val_GCR & ~RX_ENABLE, msp->registers + MSP_GCR);
+	reg_val_DMACR = readl(msp->registers + MSP_DMACR);
+	writel(reg_val_DMACR & ~RX_DMA_ENABLE, msp->registers + MSP_DMACR);
+	reg_val_IMSC = readl(msp->registers + MSP_IMSC);
+	writel(reg_val_IMSC &
+			~(RX_SERVICE_INT | RX_OVERRUN_ERROR_INT),
+			msp->registers + MSP_IMSC);
+
+	msp->dir_busy &= ~MSP_DIR_RX;
+}
+
+static void disable_msp_tx(struct ux500_msp *msp)
+{
+	u32 reg_val_GCR, reg_val_DMACR, reg_val_IMSC;
+
+	reg_val_GCR = readl(msp->registers + MSP_GCR);
+	writel(reg_val_GCR & ~TX_ENABLE, msp->registers + MSP_GCR);
+	reg_val_DMACR = readl(msp->registers + MSP_DMACR);
+	writel(reg_val_DMACR & ~TX_DMA_ENABLE, msp->registers + MSP_DMACR);
+	reg_val_IMSC = readl(msp->registers + MSP_IMSC);
+	writel(reg_val_IMSC &
+			~(TX_SERVICE_INT | TX_UNDERRUN_ERR_INT),
+			msp->registers + MSP_IMSC);
+
+	msp->dir_busy &= ~MSP_DIR_TX;
+}
+
+static int disable_msp(struct ux500_msp *msp, unsigned int dir)
+{
+	u32 reg_val_GCR;
+	unsigned int disable_tx, disable_rx;
+
+	reg_val_GCR = readl(msp->registers + MSP_GCR);
+	disable_tx = dir & MSP_DIR_TX;
+	disable_rx = dir & MSP_DIR_TX;
+	if (disable_tx && disable_rx) {
+		reg_val_GCR = readl(msp->registers + MSP_GCR);
+		writel(reg_val_GCR | LOOPBACK_MASK,
+				msp->registers + MSP_GCR);
+
+		/* Flush TX-FIFO */
+		flush_fifo_tx(msp);
+
+		/* Disable TX-channel */
+		writel((readl(msp->registers + MSP_GCR) &
+			       (~TX_ENABLE)), msp->registers + MSP_GCR);
+
+		/* Flush RX-FIFO */
+		flush_fifo_rx(msp);
+
+		/* Disable Loopback and Receive channel */
+		writel((readl(msp->registers + MSP_GCR) &
+				(~(RX_ENABLE | LOOPBACK_MASK))),
+				msp->registers + MSP_GCR);
+
+		disable_msp_tx(msp);
+		disable_msp_rx(msp);
+	} else if (disable_tx)
+		disable_msp_tx(msp);
+	else if (disable_rx)
+		disable_msp_rx(msp);
+
+	return 0;
+}
+
+int ux500_msp_i2s_trigger(struct ux500_msp *msp, int cmd, int direction)
+{
+	u32 reg_val_GCR, enable_bit;
+
+	if (msp->msp_state == MSP_STATE_IDLE) {
+		dev_err(msp->dev, "%s: ERROR: MSP is not configured!\n",
+			__func__);
+		return -EINVAL;
+	}
+
+	switch (cmd) {
+	case SNDRV_PCM_TRIGGER_START:
+	case SNDRV_PCM_TRIGGER_RESUME:
+	case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
+		if (direction == SNDRV_PCM_STREAM_PLAYBACK)
+			enable_bit = TX_ENABLE;
+		else
+			enable_bit = RX_ENABLE;
+		reg_val_GCR = readl(msp->registers + MSP_GCR);
+		writel(reg_val_GCR | enable_bit, msp->registers + MSP_GCR);
+		break;
+
+	case SNDRV_PCM_TRIGGER_STOP:
+	case SNDRV_PCM_TRIGGER_SUSPEND:
+	case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
+		if (direction == SNDRV_PCM_STREAM_PLAYBACK)
+			disable_msp_tx(msp);
+		else
+			disable_msp_rx(msp);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+int ux500_msp_i2s_close(struct ux500_msp *msp, unsigned int dir)
+{
+	int status = 0;
+
+	dev_dbg(msp->dev, "%s: Enter (dir = 0x%01x).\n", __func__, dir);
+
+	status = disable_msp(msp, dir);
+	if (msp->dir_busy == 0) {
+		/* disable sample rate and frame generators */
+		msp->msp_state = MSP_STATE_IDLE;
+		writel((readl(msp->registers + MSP_GCR) &
+			       (~(FRAME_GEN_ENABLE | SRG_ENABLE))),
+			      msp->registers + MSP_GCR);
+
+		writel(0, msp->registers + MSP_GCR);
+		writel(0, msp->registers + MSP_TCF);
+		writel(0, msp->registers + MSP_RCF);
+		writel(0, msp->registers + MSP_DMACR);
+		writel(0, msp->registers + MSP_SRG);
+		writel(0, msp->registers + MSP_MCR);
+		writel(0, msp->registers + MSP_RCM);
+		writel(0, msp->registers + MSP_RCV);
+		writel(0, msp->registers + MSP_TCE0);
+		writel(0, msp->registers + MSP_TCE1);
+		writel(0, msp->registers + MSP_TCE2);
+		writel(0, msp->registers + MSP_TCE3);
+		writel(0, msp->registers + MSP_RCE0);
+		writel(0, msp->registers + MSP_RCE1);
+		writel(0, msp->registers + MSP_RCE2);
+		writel(0, msp->registers + MSP_RCE3);
+	}
+
+	return status;
+
+}
+
+static int ux500_msp_i2s_of_init_msp(struct platform_device *pdev,
+				struct ux500_msp *msp,
+				struct msp_i2s_platform_data **platform_data)
+{
+	struct msp_i2s_platform_data *pdata;
+
+	*platform_data = devm_kzalloc(&pdev->dev,
+				     sizeof(struct msp_i2s_platform_data),
+				     GFP_KERNEL);
+	pdata = *platform_data;
+	if (!pdata)
+		return -ENOMEM;
+
+	msp->playback_dma_data.dma_cfg = devm_kzalloc(&pdev->dev,
+					sizeof(struct stedma40_chan_cfg),
+					GFP_KERNEL);
+	if (!msp->playback_dma_data.dma_cfg)
+		return -ENOMEM;
+
+	msp->capture_dma_data.dma_cfg = devm_kzalloc(&pdev->dev,
+					sizeof(struct stedma40_chan_cfg),
+					GFP_KERNEL);
+	if (!msp->capture_dma_data.dma_cfg)
+		return -ENOMEM;
+
+	return 0;
+}
+
+int ux500_msp_i2s_init_msp(struct platform_device *pdev,
+			struct ux500_msp **msp_p,
+			struct msp_i2s_platform_data *platform_data)
+{
+	struct resource *res = NULL;
+	struct device_node *np = pdev->dev.of_node;
+	struct ux500_msp *msp;
+	int ret;
+
+	*msp_p = devm_kzalloc(&pdev->dev, sizeof(struct ux500_msp), GFP_KERNEL);
+	msp = *msp_p;
+	if (!msp)
+		return -ENOMEM;
+
+	if (!platform_data) {
+		if (np) {
+			ret = ux500_msp_i2s_of_init_msp(pdev, msp,
+							&platform_data);
+			if (ret)
+				return ret;
+		} else
+			return -EINVAL;
+	} else {
+		msp->playback_dma_data.dma_cfg = platform_data->msp_i2s_dma_tx;
+		msp->capture_dma_data.dma_cfg = platform_data->msp_i2s_dma_rx;
+		msp->id = platform_data->id;
+	}
+
+	msp->dev = &pdev->dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (res == NULL) {
+		dev_err(&pdev->dev, "%s: ERROR: Unable to get resource!\n",
+			__func__);
+		return -ENOMEM;
+	}
+
+	msp->playback_dma_data.tx_rx_addr = res->start + MSP_DR;
+	msp->capture_dma_data.tx_rx_addr = res->start + MSP_DR;
+
+	msp->registers = devm_ioremap(&pdev->dev, res->start,
+				      resource_size(res));
+	if (msp->registers == NULL) {
+		dev_err(&pdev->dev, "%s: ERROR: ioremap failed!\n", __func__);
+		return -ENOMEM;
+	}
+
+	msp->msp_state = MSP_STATE_IDLE;
+	msp->loopback_enable = 0;
+
+	return 0;
+}
+
+void ux500_msp_i2s_cleanup_msp(struct platform_device *pdev,
+			struct ux500_msp *msp)
+{
+	dev_dbg(msp->dev, "%s: Enter (id = %d).\n", __func__, msp->id);
+}
+
+MODULE_LICENSE("GPL v2");