diff options
Diffstat (limited to 'Documentation/devicetree/bindings/input/iqs269a.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/input/iqs269a.yaml | 552 |
1 files changed, 552 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/input/iqs269a.yaml b/Documentation/devicetree/bindings/input/iqs269a.yaml new file mode 100644 index 000000000..3c430d385 --- /dev/null +++ b/Documentation/devicetree/bindings/input/iqs269a.yaml @@ -0,0 +1,552 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/iqs269a.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Azoteq IQS269A Capacitive Touch Controller + +maintainers: + - Jeff LaBundy <jeff@labundy.com> + +description: | + The Azoteq IQS269A is an 8-channel capacitive touch controller that features + additional Hall-effect and inductive sensing capabilities. + + Link to datasheet: https://www.azoteq.com/ + +properties: + compatible: + const: azoteq,iqs269a + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + azoteq,hall-enable: + type: boolean + description: + Enables Hall-effect sensing on channels 6 and 7. In this case, keycodes + assigned to channel 6 are ignored and keycodes assigned to channel 7 are + interpreted as switch codes. Refer to the datasheet for requirements im- + posed on channels 6 and 7 by Hall-effect sensing. + + azoteq,suspend-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: | + Specifies the power mode during suspend as follows: + 0: Automatic (same as normal runtime, i.e. suspend/resume disabled) + 1: Low power (all sensing at a reduced reporting rate) + 2: Ultra-low power (channel 0 proximity sensing) + 3: Halt (no sensing) + + azoteq,clk-div: + type: boolean + description: Divides the device's core clock by a factor of 4. + + azoteq,ulp-update: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 7 + default: 3 + description: Specifies the ultra-low-power mode update rate. + + azoteq,reseed-offset: + type: boolean + description: + Applies an 8-count offset to all long-term averages upon either ATI or + reseed events. + + azoteq,filt-str-lp-lta: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Specifies the long-term average filter strength during low-power mode. + + azoteq,filt-str-lp-cnt: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Specifies the raw count filter strength during low-power mode. + + azoteq,filt-str-np-lta: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Specifies the long-term average filter strength during normal-power mode. + + azoteq,filt-str-np-cnt: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Specifies the raw count filter strength during normal-power mode. + + azoteq,rate-np-ms: + minimum: 0 + maximum: 255 + default: 16 + description: Specifies the report rate (in ms) during normal-power mode. + + azoteq,rate-lp-ms: + minimum: 0 + maximum: 255 + default: 160 + description: Specifies the report rate (in ms) during low-power mode. + + azoteq,rate-ulp-ms: + multipleOf: 16 + minimum: 0 + maximum: 4080 + default: 160 + description: Specifies the report rate (in ms) during ultra-low-power mode. + + azoteq,timeout-pwr-ms: + multipleOf: 512 + minimum: 0 + maximum: 130560 + default: 2560 + description: + Specifies the length of time (in ms) to wait for an event during normal- + power mode before transitioning to low-power mode. + + azoteq,timeout-lta-ms: + multipleOf: 512 + minimum: 0 + maximum: 130560 + default: 32768 + description: + Specifies the length of time (in ms) to wait before resetting the long- + term average of all channels. Specify the maximum timeout to disable it + altogether. + + azoteq,ati-band-disable: + type: boolean + description: Disables the ATI band check. + + azoteq,ati-lp-only: + type: boolean + description: Limits automatic ATI to low-power mode. + + azoteq,ati-band-tighten: + type: boolean + description: Tightens the ATI band from 1/8 to 1/16 of the desired target. + + azoteq,filt-disable: + type: boolean + description: Disables all raw count filtering. + + azoteq,gpio3-select: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 7 + default: 0 + description: + Selects the channel for which the GPIO3 pin represents touch state. + + azoteq,dual-direction: + type: boolean + description: + Specifies that long-term averages are to freeze in the presence of either + increasing or decreasing counts, thereby permitting events to be reported + in either direction. + + azoteq,tx-freq: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: | + Specifies the inductive sensing excitation frequency as follows (paren- + thesized numbers represent the frequency if 'azoteq,clk-div' is present): + 0: 16 MHz (4 MHz) + 1: 8 MHz (2 MHz) + 2: 4 MHz (1 MHz) + 3: 2 MHz (500 kHz) + + azoteq,global-cap-increase: + type: boolean + description: Increases the global capacitance adder from 0.5 pF to 1.5 pF. + + azoteq,reseed-select: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: | + Specifies the event(s) that prompt the device to reseed (i.e. reset the + long-term average) of an associated channel as follows: + 0: None + 1: Proximity + 2: Proximity or touch + 3: Proximity, touch or deep touch + + azoteq,tracking-enable: + type: boolean + description: + Enables all associated channels to track their respective reference + channels. + + azoteq,filt-str-slider: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 1 + description: Specifies the slider coordinate filter strength. + +patternProperties: + "^channel@[0-7]$": + type: object + description: + Represents a single sensing channel. A channel is active if defined and + inactive otherwise. + + properties: + reg: + minimum: 0 + maximum: 7 + description: Index of the channel. + + azoteq,reseed-disable: + type: boolean + description: + Prevents the channel from being reseeded if the long-term average + timeout (defined in 'azoteq,timeout-lta') expires. + + azoteq,blocking-enable: + type: boolean + description: Specifies that the channel is a blocking channel. + + azoteq,slider0-select: + type: boolean + description: Specifies that the channel participates in slider 0. + + azoteq,slider1-select: + type: boolean + description: Specifies that the channel participates in slider 1. + + azoteq,rx-enable: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + items: + minimum: 0 + maximum: 7 + description: + Specifies the CRX pin(s) associated with the channel. By default, only + the CRX pin corresponding to the channel's index is enabled (e.g. CRX0 + for channel 0). + + azoteq,tx-enable: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + items: + minimum: 0 + maximum: 7 + default: [0, 1, 2, 3, 4, 5, 6, 7] + description: Specifies the TX pin(s) associated with the channel. + + azoteq,meas-cap-decrease: + type: boolean + description: + Decreases the internal measurement capacitance from 60 pF to 15 pF. + + azoteq,rx-float-inactive: + type: boolean + description: Floats any inactive CRX pins instead of grounding them. + + azoteq,local-cap-size: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + default: 0 + description: | + Specifies the capacitance to be added to the channel as follows: + 0: None + 1: Global adder (based on 'azoteq,global-cap-increase') + 2: Global adder + 0.5 pF + + azoteq,invert-enable: + type: boolean + description: + Inverts the polarity of the states reported for proximity, touch and + deep-touch events relative to their respective thresholds. + + azoteq,proj-bias: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 2 + description: | + Specifies the bias current applied during projected-capacitance + sensing as follows: + 0: 2.5 uA + 1: 5 uA + 2: 10 uA + 3: 20 uA + + azoteq,sense-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 9, 14, 15] + default: 0 + description: | + Specifies the channel's sensing mode as follows: + 0: Self capacitance + 1: Projected capacitance + 9: Self or mutual inductance + 14: Hall effect + 15: Temperature + + azoteq,sense-freq: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 1 + description: | + Specifies the channel's sensing frequency as follows (parenthesized + numbers represent the frequency if 'azoteq,clk-div' is present): + 0: 4 MHz (1 MHz) + 1: 2 MHz (500 kHz) + 2: 1 MHz (250 kHz) + 3: 500 kHz (125 kHz) + + azoteq,static-enable: + type: boolean + description: Enables the static front-end for the channel. + + azoteq,ati-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 3 + description: | + Specifies the channel's ATI mode as follows: + 0: Disabled + 1: Semi-partial + 2: Partial + 3: Full + + azoteq,ati-base: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [75, 100, 150, 200] + default: 100 + description: Specifies the channel's ATI base. + + azoteq,ati-target: + $ref: /schemas/types.yaml#/definitions/uint32 + multipleOf: 32 + minimum: 0 + maximum: 2016 + default: 512 + description: Specifies the channel's ATI target. + + azoteq,assoc-select: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + items: + minimum: 0 + maximum: 7 + description: + Specifies the associated channels for which the channel serves as a + reference channel. By default, no channels are selected. + + azoteq,assoc-weight: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + default: 0 + description: + Specifies the channel's impact weight if it acts as an associated + channel (0 = 0% impact, 255 = 200% impact). + + patternProperties: + "^event-prox(-alt)?$": + type: object + $ref: input.yaml# + description: + Represents a proximity event reported by the channel in response to + a decrease in counts. Node names suffixed with '-alt' instead corre- + spond to an increase in counts. + + By default, the long-term average tracks an increase in counts such + that only events corresponding to a decrease in counts are reported + (refer to the datasheet for more information). + + Specify 'azoteq,dual-direction' to freeze the long-term average when + the counts increase or decrease such that events of either direction + can be reported. Alternatively, specify 'azoteq,invert-enable' to in- + vert the polarity of the states reported by the channel. + + Complementary events (e.g. event-touch and event-touch-alt) can both + be present and specify different key or switch codes, but not differ- + ent thresholds or hysteresis (if applicable). + + properties: + azoteq,thresh: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + default: 10 + description: Specifies the threshold for the event. + + linux,code: true + + additionalProperties: false + + "^event-touch(-alt)?$": + type: object + $ref: input.yaml# + description: Represents a touch event reported by the channel. + + properties: + azoteq,thresh: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + default: 8 + description: Specifies the threshold for the event. + + azoteq,hyst: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + default: 4 + description: Specifies the hysteresis for the event. + + linux,code: true + + additionalProperties: false + + "^event-deep(-alt)?$": + type: object + $ref: input.yaml# + description: Represents a deep-touch event reported by the channel. + + properties: + azoteq,thresh: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + default: 26 + description: Specifies the threshold for the event. + + azoteq,hyst: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + default: 0 + description: Specifies the hysteresis for the event. + + linux,code: true + + additionalProperties: false + + required: + - reg + + additionalProperties: false + +required: + - compatible + - reg + - interrupts + - "#address-cells" + - "#size-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/input/input.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touch@44 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "azoteq,iqs269a"; + reg = <0x44>; + interrupt-parent = <&gpio>; + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; + + azoteq,hall-enable; + azoteq,suspend-mode = <2>; + + channel@0 { + reg = <0x0>; + + event-prox { + linux,code = <KEY_POWER>; + }; + }; + + channel@1 { + reg = <0x1>; + azoteq,slider0-select; + }; + + channel@2 { + reg = <0x2>; + azoteq,slider0-select; + }; + + channel@3 { + reg = <0x3>; + azoteq,slider0-select; + }; + + channel@4 { + reg = <0x4>; + azoteq,slider0-select; + }; + + channel@5 { + reg = <0x5>; + azoteq,slider0-select; + }; + + channel@6 { + reg = <0x6>; + azoteq,invert-enable; + azoteq,static-enable; + azoteq,reseed-disable; + azoteq,rx-enable = <0>; + azoteq,sense-freq = <0x0>; + azoteq,sense-mode = <0xE>; + azoteq,ati-mode = <0x0>; + azoteq,ati-base = <200>; + azoteq,ati-target = <320>; + }; + + channel@7 { + reg = <0x7>; + azoteq,invert-enable; + azoteq,static-enable; + azoteq,reseed-disable; + azoteq,rx-enable = <0>, <6>; + azoteq,sense-freq = <0x0>; + azoteq,sense-mode = <0xE>; + azoteq,ati-mode = <0x3>; + azoteq,ati-base = <200>; + azoteq,ati-target = <320>; + + event-touch { + linux,code = <SW_LID>; + }; + }; + }; + }; + +... |